Disk error when trying to print

we very time I tray to print from Photoshop CS5 I have the following mesaje
Could not print “...............JPG” because of a disk error.
Any help?

If you give complete and detailed information about your setup and the issue at hand, such as your platform (Mac or Win), exact versions of your OS, of Photoshop and of Bridge, machine specs, printer specs, what troubleshooting steps you have taken so far, what error message(s) you receive, if having issues opening raw files also the exact camera make and model that generated them, etc., someone may be able to help you.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

Similar Messages

FireFox keep saying "unexpected error" when trying to print web pages.

FireFox keep saying "unexpected error" when trying to print web pages. The print preview works OK, but when you try to print that "unexpected error" jumps up.
Please email me on what to do to get FireFox to work.
I don't see anything in the FAQ that might help me.

Hi,
Please also try this setting: Windows start menu or Control Panel > '''Devices and Printers''', right-click the printer > '''Printer properties''' > '''Advanced''', and select '''Start printing after the last page is spooled'''. In this case you can also close Firefox after spooling is over (usually much faster than direct printing), and printing will continue.
Also as a general case, if you have security software (antivirus, firewall etc.) installed, you can try deleting all existing instances of Firefox and its related processes/files in all the different configuration modules/areas of the security software like process monitoring, sub/spawned process control, virtualization, HIPS etc., in addition to the security software's main configuration panel. Instead create new fully allowed/trusted rules for Firefox + its related processes in all the different modules/panels - a genuine/original Firefox installer as well as all the installed EXEs (Application) and DLLs (Application extension) are digitally signed by Mozilla Corporation (right-click > Properties > Digital Signatures). Even otherwise, some security software may also ask again when Firefox and/or its sub processes are started, and you may be able to allow/trust at that time. Please see [https://support.mozilla.org/en-US/kb/Firewalls this].
[http://kb.mozillazine.org/Firewalls AV/Firewalls Configuration]

Rundll32 error when trying to print in colour, or trying to change/configure print settings.

Hey there,
I just got a new Windows 8.1 computer. I could print fine for a few days with my HP CP1215 in color. Then I changed it default to grayscale, and when I went to change it back, it told me the driver is not installed. I reinstalled the driver, and went to Properties, and it says RUNDLL32 ERROR.
Then it says the driver isn't installed.
And then I start all over again.
Please help.

Hi Divechickie,
Welcome to the HP Forums, I hope you enjoy your experience!
I understand you are getting a error when trying to open the printer properties on Win 8.1 after reinstalling the printer driver. I will be happy to help you.
If you are using the Windows built in driver then I would download and run the HP Color Laserjet Plug and Play Package. HP Color LaserJet CP1215 Printer Drivers.
If that doesn't work you could do a system restore back to when everything was working properly.
How to refresh, reset, or restore your PC.
Hope this resolves your issue.
Thank you for posting on the HP Forums.
Have a wonderful day!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

I'm suddenly getting a "communication error" when trying to print

When trying to print a document from Pages, which I have done before, my computer is showing "communication error" in the printer window.

HI Larry,
You have helped me before i remember with a whole iphoto NiGhtMaRe!
As i said to leonie i have solved it by deleting all the previously saved photos and then it worked.
After which i formatted the card as per your suggestion and everything seems okay.
It was all overdue. Leaving that many photos on one card was stupid.
Anyway thanks all.
J.

I get scrip error when trying to print web pages.

I get a scrip error message when trying to print web pages and it will not print.

FreddieP,
You may want to download and run the HP Print and Scan Doctor. It helps diagnose and resolve printing issues. You can click on the link below to go right to it.
Let us know if this works for your issue or not.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=oj-106151-2&cc=us&dlc=en&lc=en...
If I helped you at all it would be great if you clicked the blue kudos star!
If I solved your post please mark it as solved to help others.
I'm a printer tech with HP.

HP Device Not Found Error when trying to print or scan wireless- HP Officejet Pro L7590

Have had HP Officejet Pro L7590 All-In-One Printer for years. Always worked fine and I had no issues printing via wireless connection. Several months ago.. Possibly after a Windows 8 update. From Windows 8 to Windows 8.1 I have not been able to use the printers wireless feature. When I try to print or scan it shows the printer as offline. Also get an error message that tells me "HP Imaging device is not found". I can still print when connected to USB. Cannot scan or use features of the HP software suite. I have tried several times to correct. Reloading the software and drivers several times, but no success. I just tried again and was able to print the test page wireless, so got all excited and thought I fixed it. Then tried to print something and got the same error message I have seen in the past. I have talked to certain supports saying that it may be a firewall setting within Windows. Any other suggestions? Thanks

Hi @rfjones002,
Welcome to the HP Support Forums! I see you are not able to print or scan wirelessly to your HP Officejet L7590 and your computer running the Windows 8.1 Operating system. You get a 'Printer offline' or 'HP Imaging device not found' errors.
I would like you to start with the steps listed below:
Hold down the Windows Logo key () on the keyboard and the 'R' to open the run box, type %temp%
Delete all files and folders from the temp folder. Choose skip if any pop ups appear saying any of the files could not be deleted
Uninstall the software again - Uninstall the Printer Software Instructions
When the uninstall has completed restart the computer
Follow these steps to reset the registry settings and options for Windows Installer.
Hold down the Windows Logo key on the keyboard and the 'R' to open the run box
In the Open box, type
msiexec /unregister
and then click OK.
Hold down the Windows Logo key on the keyboard and the 'R' to open the run box
In the Open box, type
msiexec /regserver
and then click OK
*Note: there is a space between the c and the /
If you have any difficulty with this step, please use this link to perform it another way. Restarting Windows Installer
Run Disk cleanup from Accessories\ System Tool < How to Delete files using Disk Cleanup
Download and install the latest version of Adobe flash player http://www.adobe.com/support/flashplayerflashplayer/downloads.html
Perform a clean boot > How to perform a clean boot in Windows
Download the following SP40669 File Download - if this does not download and or install please proceed to the next step.
Turn off the Real-Time Scanning and Firewalls; The image below is a McAfee example, if you have a different antivirus program and need help disabling Real-Time Scanning and Firewalls let me know.
- Image source
Now you can go ahead and download and install the software here >
HP Officejet Pro Full Feature Software and Driver
If you are unable to print a test page, please run the HP Print and Scan Doctor- It was designed by HP to provide users with the troubleshooting and problem solving features needed to resolve many common problems experienced with HP print and scan products connected to Windows-based computers.
Please let me know if this was successful! I will watch for your reply.
Thank you,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

I get a disk error when trying to upgrade to mountain lion on my mac book pro that also runs bootcamp

I recently tried to upgrade my macbook pro OSX to mountain lion via the app store. When it tried to install it gives me a disk error. I have run disk utilities and repaired, verified etc. but it makes no difference. I am running bootcamp as well and have tried to modifiy the partition sizes in disk utilities, but it says for both that they cannot be modified. I can switch my startup disk and reboot in windows, no problem, so getting my files off isnt the issue. I have also tried to recover the hard disk using time machine which i was lucky enough to backup the day before it all went wrong. However, time machine runs fine until it asks me which disk to recover and it gives me an option of the time machine disk or bootcamp, but no option for my mac partition. So, I have tried everything that makes snese, but getting errors with disks lock, cant repartition, disk error needs repair (which i know is not true, its only because of the Mountain Lion OSX that its messed up). Any ideas?

You have some other problem with your boot drive that has corrupted data backed up to the TimeMacine drive.
My advice is to boot into each operating system and manually backup just your Users files each to separate regular external drives (no Timemachine or backup software) and disconnect.
Make a note of any serial numbers, emails, address book contacts, export bookmarks etc. that isn't typically in your users folders data.
You might be able to Winclone 3 the Windows as a whole thing as it's appearing not to have issues but it's your MacintoshHD partition that is so that will have to be rebuilt from scratch.
Most commonly used backup methods
If your OS X parititon doesn't boot, you can use this to recover files.
Create a data recovery/undelete external boot drive
Without any further detail about your machine I can't advise specifically what to do, but it involves using Disk Utility to Zero Erase (move slider one spot to the right or in 10.6 using Security Option) the ENTIRE boot drive and reformatting, then installing OSX fresh and then setting up BootCamp again.
If you wish to switch your boot drive for something better, this is a good time to do this.
Install/upgrade RAM or storage drive in Mac's
If your machine is capable of Internet Recovery, then use that, then upgrade.
If your machine came with 10.6 or earlier, then use the 10.6 install disks and work up from there.
Erase, formatting, OS X installs on Mac's

Error WHen trying to print a crystal report

I am trying to print a system crystal report and it is giving me the following error: "Error during printing; ensure all parameters are defined". And it prints the first page, but none of the consecutive pages if there are more than 1. Is there some type of setting that needs to be set for printing?

Hmmmmm it says "page range" ALL. I was able to print fine until I created a new layout and saved it. THen I went to print it and got the error. But it seems I get the error when I print any crystal report in any DB. Is this a setting in crystal, SAP, or printer itself? I can print the second page if I toggle through to the second page on the crystal report view, and go to print, and put 2 next to pages feild. Otherwise it is set to print ALL, however it is not doing that.

'Printing Error' error when trying to print in Safari

Hello, I am running OSX Mavericks and ran into this problem tonight. I have been using my new Macbook air for over a month and never had this problem happen at all. Whenever I try to print something from a webpage Safari gives me the error ' Print error' and no other info. No printing happens obviously. I have deleted the printer and added it again, I have deleted the drivers and installed them again. The only thing that seems to work is that if I restart the computer and try to print it will work 1 time and 1 time only. Then I get the same print error warning. Any ideas??? Thanks in advance!

Linc, thanks for the help. I have kind of figured it out...maybe. I have never had this issue at all on any of my Macs (3). Last night when this started to happen I was attempting to print some reviews off of Amazon (which i had never attempted before either). So I would print one page of the review on first attempt no problem but then have to shut the computer off to be able to then print the next page of reviews. I then tried to print off other sites and I had no problem. I just now printed our convo above and it cabme out no problem and I can print PDF's and word documents no problem. So it looks like maybe Amazon has something that stops you from printing their reviews maybe??? I had to save the review webpage as a PDF file and then print it, which worked. So looks like Amazon does not want their reviews printed I guess. Cheers for the help though!

Receiving non system disk error when trying to install Windows 8.1 full version on Mac Mini

I am trying to install Windows 8.1 full version on a Late 2012 Mac Mini using OS X 10.9.2 using boot camp.
The windows partion has been created but when the mac mini reboots I receive a Non System Disk error. Press any key to continue
Please could someone assist with my problem

Thanks for that information, I removed all the external devices except the Superdrive.
Ran Boot camp again, created the MS Dos partition, and the mac restarted.
Now I have received the "No bootable device -- insert boot disk and press any key"
Please help

In Flash Builder: "No Disk" Error when trying to switch to Design View

Just had Flash Builder Beta 1 uninstalled and Beta 2 installed instead.
When I try to switch to Design View or open a link from Start Page in Flash Builder Beta 2, the application freezes and "No Disk" error message pops up.

You have some other problem with your boot drive that has corrupted data backed up to the TimeMacine drive.
My advice is to boot into each operating system and manually backup just your Users files each to separate regular external drives (no Timemachine or backup software) and disconnect.
Make a note of any serial numbers, emails, address book contacts, export bookmarks etc. that isn't typically in your users folders data.
You might be able to Winclone 3 the Windows as a whole thing as it's appearing not to have issues but it's your MacintoshHD partition that is so that will have to be rebuilt from scratch.
Most commonly used backup methods
If your OS X parititon doesn't boot, you can use this to recover files.
Create a data recovery/undelete external boot drive
Without any further detail about your machine I can't advise specifically what to do, but it involves using Disk Utility to Zero Erase (move slider one spot to the right or in 10.6 using Security Option) the ENTIRE boot drive and reformatting, then installing OSX fresh and then setting up BootCamp again.
If you wish to switch your boot drive for something better, this is a good time to do this.
Install/upgrade RAM or storage drive in Mac's
If your machine is capable of Internet Recovery, then use that, then upgrade.
If your machine came with 10.6 or earlier, then use the 10.6 install disks and work up from there.
Erase, formatting, OS X installs on Mac's

Error when trying to print a form

Hi all,
I'm getting the following error when I try to print a form (transaction SFP - Form Builder):
Cannot find PDL type for output device LOCL
Message no. FPRUNX113
Does anybody know why I'm getting this error? I get it for all forms I try, but not when e.g. I print some source code in se80..., so I guess it's not due to my printer settings.
tia,
Jeroen

Hi Jeroen,
Maybe you don't have in the TSP03 table the Printer Declaration for the LOCL Output Device (TSP03-PADEST field).
Please take a look at SE16 transaction to confirm it.
NOTE: Try to see also the ADS_GET_PRINTER_ATTRIBUTES function module and the LFP_PRINTPRI include, the error you are getting is occurring in the Line 60 of that include.
Regards,
Daniel Carvalho.

Access Denied error when trying to print over the network

I just upgraded my Internet service and leased a new modem. My laptop is connected to the network and is able to browse the Internet. I have file and printer shared tuned on on both the desktop and the laptop. The printer is listed on my laptop, but I cannot print over the network to my HP PSC 1401 All In One. I get an Access Denied error even though the printer should still be connected to the network.

bump

How do I deal with "Acces Denied" error when trying to print to Adobe PDF printer driver

Windows 7 64 bit OS (updated)
Adobe Acrobat XI (11.0.06.70)
I am unable to create a PDF file from within the Windows 7 print dialog. Each time, I receive a terse "Access Denied" error followed by the display below (the progress bar never advances). I thought upgrading to Adobe Acrobat XI might fix this but no such luck. It seems that others have experienced similar issues. I noticed in the display below that Adobe is trying to create the file in a folder which does not exist (at least I can't see it even after setting my preferences to display hidden files). I have the hope that, if the folder were present and accessible, Adobe would create the file without trouble. Is there a way to instruct Adobe Acrobat XI to create this temporary file in a different location? One of my frustrations is that I used to be able to print Adobe Acrobat files without trouble on the same computer. I wonder whether the use of a registry cleaner may have contributed to my problem.
What are the best practices for addressing the Access Denied and inability to print problems I've encountered?
Thanks for any help you can provide in sorting out this problem.
Best,
Matt

I have been having the exact same problem with Adobe Acrobat X. I have uninstalled and reinstalled numerous times and applied all the latest updates. Every time I try to print ANTHING to the Adobe PDF print driver, the software hangs (MS Office, webpage, or other programs). When I finally kill the process using Task Manager, I find the little "Access Denied" box. This has been happening for nearly one year. I have limped along since I have other computers to use. I have attempted to find answers on this forum in the past, and no one seems to have a clear answer to the problem.
I, too, was tempted to upgrade to XI, but Matt's post settled the matter, since it did not help him.
I am using Win 7 Home (64 bit) and until this issue started, I have had no problem with AA X.
Where are the Adobe experts when you need them? Please help us.

My external hard drive accidentally switched off during Disk Utility's "erase free space" process. I restarted the external hard drive and Disk Utility, but now I get the "couldn't mount disk" error when trying to finish the erase. Please help!

My external Lacie Quadra hard drive accidentally switched off in the middle of "erase free space", and when I switched it back on Disk Utility was hanging. So I Force Quit Disk Utility and restarted it. Now when I try to erase I get
"Secure Disk Erase failed with the error: Couldn’t unmount disk."
But "erase free space" seems to work...
What can I do? I'm erasing as I'm giving the drive to someone else and I wanted to wipe it clean.
Also should I use "erase" or "erase free space" if I want to wipe the drive clean?
Please help!

Sorry I don't really understand.... there are no partitions on the drive. How do I repartition it?
And should I use "erasing free space" or "erase" for wiping clean my drive of everything? Erase seems to be faster last tiem I tried.
Thanks!

Disk error when trying to print

Similar Messages

Maybe you are looking for