Documentation for programming a PXI card with VISA in LabVIEW.

Hi,
Where can I find a documentation for programming a PXI card with VISA in
LabVIEW?
Thanks.
Denys.

Dan,
Thank you for your answer, short but useful to start.
Denys.
"Dan Mondrik" a ecrit dans le message news:
[email protected]..
> Denys:
>
> Our NI-VISA documentation for PXI has been somewhat scarce. We are
> improving it in the next version. In the meantime...
>
> Call VISA Find Resources with "PXI?*INSTR" to find all PXI devices.
> Call VISA Open with a device string like "PXI::devicenum::INSTR" or
> "PXI[bus]::devicenum[::function]::INSTR". In LabVIEW, use the VISA
> class "PXI Instr", available since LV 5.0. (The generic "Instr" will
> also work but will also present GPIB and VXI options and may be too
> confusing.)
>
> The property node has all the available PXI properties such as
> BAR0-BAR5 base/s
ize/type, and also manufacturer ID and model code.
> You can use all the register based in/out/peek/poke methods, just make
> sure to use the appropriate address space for your device.
>
> Dan Mondrik
> Senior Software Engineer, NI-VISA
> National Instruments

Similar Messages

  • Programming multiple smart cards with multiple smart card readers in a PC causes a PCSCException in a smart card that is in progress

    Hi,
    I develop a Java code using smartcardio API to program a smart card. My GUI allows to add at most 5 smart card readers that will wait for card present, then do authentication and program the smart card with an application, then wait for card removal. This is a separate thread running in a loop for each smart card reader added as programmer.
    The problem occurs when a certain smart card is in progress and I inserted another smart card to another smart card reader.  Both smart card reader halts and throw sun.security.smartcardio.PCSCException: Unknown error 0x8010002f.
    I also observed that every time there is an attempt to insert/remove a smart card in the smart card reader that is connected to the USB port would cause the programming in progress to be interrupted and throw the PCSCException.
    These are some exceptions I got during my testing:
    sun.security.smartcardio.PCSCException: Unknown error 0x8010002f
      at sun.security.smartcardio.PCSC.SCardTransmit(Native Method)
      at sun.security.smartcardio.ChannelImpl.doTransmit(ChannelImpl.java:171)
    java.lang.Exception: Loader Record Failed: 6E | 0 //Sometimes I got this return code SW1 0x6E SW2 0x00 which means an APDU with an invalid 'CLA' bytes was received. I had check the command before it was sent and it was correct.
    Help me understand this issue. I think the CardTerminal.isCardPresent(), CardTerminal.waitForCardPresent(0), and CardTerminal.waitForCardAbsent(0) cause this issue that CardChannel.transmit(apduCommand) is interrupted or the smart card insertion/removal causes the CardChannel.transmit(apduCommand) is interrupted.
    Regards,
    Knivez

    Hi,
    when you work with one smartcard reader only usually you address the slot -1 that means "the first found".
    But to deal with multiple readers you have to use slots of course since one reader will be slot 0, next reader will be slot 1 and so on...
    So a credential object will be identified on a system by a couple
    <slot,alias>
    After that, the way to address slots (I mean the syntax) depends on the classes you are using...
    Bye

  • How to build FM radio receiver on PXI 5600 and PXI 5142 with help of labview

    How to build FM radio receiver on PXI 5600 and PXI 5142 with help of labview?
    PLZ TELL ME!
    Solved!
    Go to Solution.

    Dude,
    Your way of asking questions sucks!
    - Do not use such fonts!
    - Try to find things out yourself first (apparently GovBob was able to find info, so could you)
    - Have you asked GovBob if he likes it that you mail him for more questions?
    You ask for a complete solution on a project YOU have to do. (you dont learn of it if you dont try it yourself first)
    Hopefully you will ask questions in a less DEMANDING way next time.
    Good luck with your project

  • Which is better, many PXI cards or fewer PXI cards with more SCXI cards?

    I have a pretty basic question.  Which is "better", using multiple PXI cards for analog inputs or a single PXI card and multiple SCXI cards?  For example, if I have say 100 channels to sample (all at the same rate), I could use 2 6225s at 80 ch each.  Or I could use 1 6220 and 4 SCXI 1100s (32 ch each).  What are the pros and cons with either approach?  Keep in mind sample rate probably isn't an issue (less than 1 kHz) but it is the same for all channels.
    Thanks.

    The pros/cons will depend on your application now and in the future.  I recommend contacting your local NI sales representative.  Synchronizing across a PXI system is easy to do via the backplane.  There are PXI/SCXI combo chassis available, you could use PXI multifunction DAQ cards and then SCC for signal conditioning for thermocouples for additional functionality later.  There are many possibilities that may be best discussed with your sales representative.
    Regards,
    h_baker
    National Instruments
    Applications Engineer
    Digital Multimeter Resources

  • How to access remotely to a PXI card with Visual C++ through an Ethernet TCP/IP link?

    I read that it was impossible to use RDA with C++, however, we must use Visual C++, and we must use TCP/IP to access to the PXI (MXI3 solution is not convenient due to its optic fiber). How can we do, which tools should be used and how to use them ?
    Thank you very much.

    RDA is supported in LabWindows/CVI, so you could try to create a new Visual C++ project with the Measurement Studio AppWizard, specifying that you want to create a LabWindows/CVI application, then specify that you want to create a Visual C++ project that incorporates LabWindows/CVI run-time libraries, then leverage CVI's RDA support in your C++ project. For some more general information, see Developing Networked Data Acquisition Systems with NI-DAQ and Networking Two PCs for Remote Data Acquisition.
    - Elton

  • Seperate Apple IDs for seperate Itunes gift cards with one Icloud account

    My wife and I both have Iphone 4s and we have one central Itunes account with all of our music on one Icloud account.   We like to listen to "OUR SHARED" music on each of our Iphone's.  Now here is our major problem:
    We each have recieved Itunes gift cards and would really like to keep the spending sepearate but both of us have access to music and videos to each of us have purchased.  We would like the ability to share the music between the two of us.  We are trying to avoid the accident of purchasing the same song twice for example.  Waste of money in my opinion. 
    I have spoken to a few apple helpers at the local apple store and were said you can do just look up the Apple support commnities.  But I have not found any luck.
    I then went ahead and spoke to two Apple tech support by phone one said she was not sure then the second which was a manager said that the Icloud is not made for music it is only made for contacts, notes, backup iphone or ipad, etc. 
    I thought she was full of hot air.  We can download all of our music through Itunes match in the icloud.  I tried to explain to her but she was oblivious.  Sad that someone in the Apple Tech support does not know her own product. 
    This is the first time in four years I have become semi frustrated with an apple product.  Everything else has been awesome to date. 
    Thanks in advance for any help.
    Doogie

    This is the screen that pops up when I attempt to purchase an app.  It does not allow me to use my Touch ID.

  • Looking for examples of VI with two or more inputs for the 1200 daq-card ( PCMCIA )

    Thank you , if you can help me by sending VI examples for the 1200 daq-card
    , with 2 or mores inputs

    You can find several examples that will work with the DAQCard-1200 at zone.ni.com/libraries/.
    Then look under Data Acquisition. There are also examples that ship with
    LV and NIDAQ. Look in ...\Labview\examples\daq\anlogin\.
    "david frazao" wrote:
    >Thank you , if you can help me by sending VI examples for the 1200 daq-card>,
    with 2 or mores inputs>>

  • Documentation for USRP 1.1 with Ettus N210

    Where can I find documentation for using USRP 1.1 with the Ettus N210 device?  The documentation that comes with USRP 1.1 has a tiny blurb on the N210 that points to the documentation for NI 292x devices for details.  There, I find:
       "For Ettus Research devices, use internal names to refer to the internal connectors inside the device case."
    I'm trying to understand how to use the API to receive upon the LFRX-LF DC-50 MHz receiver daughter board.  The two connectors on that board are labeled "RX-A" and "RX-B", but I can't get those names to work, nor can I get "RF1" or "RF2" to work (the names on the case). 
    Any suggestions?
    Ultimately, I'd like to stream data from both connectors at the same time, if that's possible.

    Hi ejubenville,
    Support for the LFRX 0-30 MHz daughter board was just added to the NI-USRP driver in version 1.1 and documentation for this daught board is limited.  While support for the LFRX is listed, I saw no mention to the LFRX-LF 0-50 MHz daughter board.  I expect that your daughter board will work, but if not this may be part of the reason. 
    As far as the driver is concerned, the Ettus N210 and the NI-292x devices will be configured the same so there is not different documentation for the N210.  I would try using RX1 and RX2 which are the names used for the other daughter boards.
    Sarah Y
    SDR Product Manager
    National Instruments | Ettus Research

  • Pxi 1033 with expresscar​d 8360

    Hello,
    I have a PXI 1033 Chassis with ExpressCard 8360. I connect it to laptop using ExpressCard.
    I want to connect it to PC desktop. Would you please tell me how can I connect. What kind of board i need to connect ExpressCard to PC desktop.
    Best regards

    There are 2 options for using your PXI 1033 with a desktop.  You can buy an NI PCIe-8361 to go in your desktop, then switch the cable between your desktop (with the NI PCIe-8361) and your laptop (with the ExpressCard-8360).  Or you can buy an ExpressCard adapter for your computer.
    If you go the adapter route, you need to get one that plugs into a PCIe slot.  ExpressCard supports 2 interfaces: PCIe and USB.  On a "real" ExpressCard slot, both interfaces are available on the connector.  Some adapters plug into USB and only provide the USB interface, which works fine for ExpressCards that use the USB interface.  Some adapters plug into a PCIe slot and have a cable that plugs into a USB header on the motherboard, so it can support both interfaces (PCIe and USB).
    The ExpressCard-8360 uses PCIe, so any adapter that connects via USB simply won't work.  Also note that the card retention isn't very good, and the slot won't support hot-plug like a native ExpressCard port.
    - Robert

  • ABAP Dump GETWA_NOT_ASSIGNED_RANGE for program /SDF/CL_EM_DUMP_COLLECTOR=====CP

    Hello,
    I am getting ABAP runtime error GETWA_NOT_ASSIGNED_RANGE every 10 minutes in my ECC Production system. This dump is occurring for program /SDF/CL_EM_DUMP_COLLECTOR=====CP with short text as "Field symbol is not assigned".
    Error Analysis:
    "A field symbol that was not assigned was accessed
    (data segment no. "-1").
    The field symbol is no longer assigned because there was an attempt
    makde previously in a Unicode program to set the field symbol using
    ASSIGN with offset and/or length specification. Here, the memory
    addressed by the offset/length specification was not within the
    allowed area."
    Information on where terminated:
    "Termination occurred in the ABAP program "/SDF/CL_EM_DUMP_COLLECTOR=====CP" -
         in "GET_FIELDTABLE".
        The main program was "SAPMSSY1 ".
        In the source code you have the termination point in line 51
        of the (Include) program "/SDF/CL_EM_DUMP_COLLECTOR=====CM005"."
    Server-Side Connection Information:
    "Information on caller of Remote Function Call (RFC):
        System.............. "Solution Manager"
        Installation Number. " "
        Database Release.... 702
        Kernel Release...... 720
        Connection Type..... 3 (2=R/2, 3=ABAP System, E=Ext., R=Reg. Ext.)
        Call Type........... "synchronous and non-transactional (emode 0, imode 0)"
        Inbound TID.........." "
        Inbound Queue Name..." "
        Outbound TID........." "
        Outbound Queue Name.." "
        Client.............. Prod Client
        User................ "SolMan user"
        Transaction......... " "
        Call Program........."SAPLE2EEM_DATA_COLLECTION"
        Function Module..... "/SDF/E2EEM_GET_DATA"
        Call Destination.... "SM_<ECC_PROD>_READ"
        Source Server....... "Solution Manager"
        Source IP Address... "Solution Manager"
        Additional information on RFC logon:
        Trusted Relationship " "
        Logon Return Code... 0
        Trusted Return Code. 0"
    I searched for SAP notes and other SCN discussion but could not find relevant information. Can someone please assist me? Thanks.
    Tanay

    Hi Srivastava,
    What process or transaction you are executing, when you got this dump, please share the detail.
    In SAP there so many areas where we can have this ABAP dump, please also share the snap shot in ST22 " How to Correct" part of dump which carries the exact program name e.g. in below snapshot program name, short text, etc  is given to search SAP note.
    Please also refer to the following sap notes:
    1840910 - Dump CHECK_SELOPT_ILLEGAL_SIGN
    1729771 - Collective corrections as of ST-PI 2008_1 SP06
    1011229 - ST-PI: Corrections for E2E Diagnostics
    Regards
    Javed

  • Report generation VIs in Labview 6.1

    Hello,
    I am havinf problems with using Labview 6.1 VIs for report generations. The VIs provided by Labview are not executable! It seems as if they had internal errors, non fixed errors. Moreover, I am not able to open the diagram because it is password protected. Does someone know if there is any patch to fix this or the reason why these VIs don't work?
    Thanks a lot!
    Regards,
    María

    Hello Maria,
    are you using the report Generation Toolkit for MS Office or the standard vis that LabVIEW provides for report generation?
    If you use the Office toolkit, this may help:
    http://digital.ni.com/public.nsf/3efedde4322fef19862567740067f3cc/c8888a9a74e75c4786256cda00694a1e?OpenDocument
    If not, this may also help:
    http://digital.ni.com/public.nsf/3efedde4322fef19862567740067f3cc/9acb175f6de483ae86256b2200776b8b?OpenDocument
    In any case, WHAT I WOULD TRY FIRST is to do a Mass Compile of the folder where the report vis are located.
    Here you can see what this does and how to perform it:
    http://digital.ni.com/public.nsf/3efedde4322fef19862567740067f3cc/654877e62a97b72986256c95006f9b24?OpenDocument
    One last question...are you having trouble only
    with executables or also during development?
    Regards,
    JorgeM.

  • Documentation for register level programming of PCI-62XX cards

    I'm looking for documentation for register level programming of PCI-62xx series cards. Does such a document exist?
    Thanks

    Scott,
    At this time we do not have a comprehensive M Series RLP manual available.  I was not aware of any plans to deliver this document last month, so you may have been given some incorrect information, in which case I apologize.  Currently, we provide the register map along with several examples showing how to program the boards for different types of operations.  If you have any specific questions, you can post them to this forum where our developers and other customers can help out.  I hope this helps. 
    Jeremy

  • How do I remove a credit/debit card from my account? I ask because I currently have a VISA gift/debit card with 50 dollars on it, but the money has run out so I want to usea new card. Also, there is no 'None' check option for payment type on my account.

    How do I remove a credit/debit card from my account? I ask because I currently have a VISA gift/debit card with 50 dollars on it, but the money has run out so I want to usea new card. Also, there is no 'None' check option for payment type on my account.

    Depending on how you created your account, "None" may or may not be an option. I believe it has something to do with whether the account was made through an App Store request or the regular iTunes Store. For example, my account allows no card but my father's doesn't allow there to be no card.
    To change the card, go to your account settings and change the information to your new card, and hit save.

  • How to alternate data storage into 2 arrays with an analog square wave input? (seems that the retriggera​ble function is not supported by my PXI card)

    Hi!  
    I'm trying to have an analog square wave input determine where data gathered from a second analog input channel is stored.  I want data to be stored to one array during the high signal period of the square wave and data to be store to another array during the low signal period of the square wave.  The square wave I'm using is of constant frequency (8.3 Hz).  I believe I need to use an analog input wave as opposed to a onboard clock or other timing mechanism because my square wave is also being used to modify the input going into my experimental setup.  Thus the data storage needs to be correlated to the timing of the data modification in the experiment.  I tried to use the retriggerable property node function, but receive error 200452, which I think means that my PXI card (6115) can't support this retriggerable function.  So I'm looking for other ways to accomplish alternating data storage in response to an incoming analog square wave.  Any help would be GREATLY appreciated... Thanks!  (I'm also quite new with LabView so toddler-type explanations would probably be most useful  )
    -Shari
    (LabView version 8.6)
    Attachments:
    Pulsed_Acq_Switch_Simplified.vi ‏47 KB

    Hello Shari,
          I am looking at your situation and it seems very intriguing.  after downloading your file I have a couple questions to ask if you don't mind answering.
          Currently in your program you are only taking one sample of data at a time,  this could lead to uneven sampling.  Would you like to sample at a consistent rate  (say 10 Kilosamples of data a second?)  if so what type of card are you using?
          Also,  Do you want your data to be in a 2-D array of data?
    Best Wishes,
    Daniel

  • Why U. S. Store refuses my Visa card with it's official and with the global science I can buy from Bahrain store    and now my account stoped with reason owe ..

    Why U. S. Store refuses my Visa card with it's official and with the global science I can buy from Bahrain store    and now my account stoped with reason owe ..

    You can ONLY use the itunes store of your country of residence ( proven by the billing address on your credit card) AND ONLY while you are physically located inside the borders of that country.
    You would have to live in the U.S and physically be located in the U.S in order ot use the U.S tunes store.  The same is true for each countrys itunes store.

Maybe you are looking for