Domain Logon and Networks

I am wondering if u would answer my question about Domains for the logon for windows 7. I would like to know the paied options for this .

Hi KombatPvP,
If you want to join the machine to a domain ,here is a link for reference :
Connect your computer to a domain
http://windows.microsoft.com/en-hk/windows/connect-computer-domain#1TC=windows-7
If you want to configure a domain environment ,the following link may be useful:
Windows Server 2012: Set Up your First Domain Controller (step-by-step)
http://social.technet.microsoft.com/wiki/contents/articles/12370.windows-server-2012-set-up-your-first-domain-controller-step-by-step.aspx
Step-By-Step: Adding a Windows Server 2012 Domain Controller to an Existing Windows Server 2003 network
http://blogs.technet.com/b/canitpro/archive/2013/05/05/step-by-step-adding-a-windows-server-2012-domain-controller-to-an-existing-windows-2003-network.aspx
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Similar Messages

Business Management Error: You are attempting to create a user with a domain logon that does not exist. Select another domain logon and try again.

Hello,
Suddenly the working CRM is being stopped for some group of users.
I drilled down to the issue and have checked that the users from Domain in which CRM is installed are having CRM access.
But for other domain user having problem to access CRM.
I tried to add a user from a domain which is not of CRM domain then it gives following error.
"Business Management Error: You are attempting to create a user with a domain logon that does not exist. Select another domain logon and try again.
<Message>LookupAccountNameW failed with error</Message> "
The change is made - AD group have upgraded Activer Directory server to 2012 R2
Please help as the Production CRM is not working for other domain user.

We have Activer Directory Structure like below.
One Root Domain says A
and there are multiple child domain like B,C,D etc...
B,C and D are all in same level,they are child of A domain.
There are two way transitive trusts between A and all the child Domain.
But there is no trust in between B and C and so on.
Our CRM server is in B domain and B domain's user can access CRM but users of Domain C,D and so on can not access CRM.
If this post answers your question, please click "Mark As Answer" on the post and "Mark as Helpful"

Leap and windows domain logon

I'm doing some test with an Air 1200 and some 352 Pc card for one of our customers.
With ACU ver. 4.25.23, I enabled LEAP authentication using the windows user name and password.
Leap authentication is successful, while windows domain logon not.
Not to say using a "normal" NIC that logon succeed.
Sniffing the packets that come out the AP, it seems the domain logon happens... I see the requests/answers between my client and the domain controller...
However, after canceling the windows domain logon I have normal connectivity with the entire network.
Someone experienced that? Any help will be greatly appreciated.
Antonio Tassone

Sure.
My attempts to logon in a windows domain using the same user/password for LEAP authentication and windows logon were unsuccessful (either using Win9x or Win NT/2000 on the client), indeed the login dialog box was stuck in something like "searching primary domain controller" or similar (I'm sorry but it's been some month ago).
Looking the Radius server log, I found an error like " xxxxx DLL rejected".
Searching the Cisco web site and the forums for that error, I read the advice to make the authentication services on the NT server to run with the privileges of one of the Windows Domain Administrator accounts.
Following that advice, and with some other tweaking explained in the document I read, I reached my goal.
I regret I can't be more precise.
Regards.

Connecting to Wireless Network with domain name and proxy servers?

Hi,
I'm trying to connect to the wireless network at my college, however it's not as straight forward as usual... The network is hidden, although I know to 'Join other network' and type in the SSID of the network and then set the authentication method to WPA-Enterprise. However, this is where I run into a problem..
To connect, I need to 'configure encryption as AES', which I'm not sure how to do on OS X. Furthermore, after signing in with my college ID I am required to 'Use the domain name [domain name]' and 'configure your browser to use the college proxy servers [example.example.net] on port [123]
Any help on this would be greatly appreciated as it's important that I log on to the network for work etc.
Thanks very much for your time.

johnthompson1993 wrote:
Hi,
To connect, I need to 'configure encryption as AES', which I'm not sure how to do on OS X. Furthermore, after signing in with my college ID I am required to 'Use the domain name [domain name]' and 'configure your browser to use the college proxy servers [example.example.net] on port [123]
The encryption should be configured automatically. To use the proxy:
1. Open System Preferences
2. Click on Network
3. Select Airport from the list on the left
4. Click on Advanced, near the bottom right
5. One of the tabs will be called Proxy. Configure your settings there.

Slow window domain logon over ezvpn netw ext mode tunnel

I have 4 branch offices connected to a central EZVPN server in network extension mode.
tunnels are working correctly but domain logon is extremely low (often more than 10 minutes).
Do you think it could be a fragmentation issue?
If it is, do you know any way to solve it?
The errors reported are in windows XP system logs are the following:
     System     > LSASRV 40961 no secure connection with server, no authentication protocol available
     Application> usernv 1030
     Application> usernv 1006
Thanks
Johnny

Hi
I am in exactly the same situation with the ASA 5510 running security plus license, version 8.0(5) 512 MB RAM
going to try to upgrade the IOS tonight and upgrade the RAM to 1GB to take it up to version 9 will let you know if it helps,
cureently download speeds are very bad aroudn 14MB where as uploads are around 96 MB

Configure Windows Domain Logon on Airport Express

The question is... How can I configure Windows Domain Logon data on an Airport Express so it connects automatically without asking each of my other devices for login credentials?
I use my Airport Express at work connecting it through ethernet, and the network uses Windows Domain credemtials to login, that is user, password and domain server. I have all data needed, this is, static IP, Gateway, DNS, user, password, etc., but I haven't found how to do this inside de Airport Express so I configure just one device instead of 3 or more.
I have tryed configuring the Airport Express as PPPoE, but that's not the solution for this problem.
Thanks in advance for the answer.

Your wireless Netgear router and AirPort Express Base Station (AX) are pretty much useless if you don't have wireless capability for your Dell desktop. The AX uses AirTunes to receive, wirelessly, iTunes from your desktop.
Just add a wireless card to your Dell and you should be in good shape. In fact, once you go wireless, you can return the Netgear router as your AX will provide Internet connectivity, stream iTunes, and share a USB printer.

Domain Logon status - not authenticated

I am starting here.
Win8.1 pro client. It is a domain client and fully goes through logon validation.
Server 2012R2 AD
On Domain client PC, active network panel responds as Private Network, FQDN mydomain.local (Unauthenticated)
I can access all server resources and get to the internet on the domain client PC.
Why Unauthenticated?
John Lenz

Hello,
have you seen similar problem and options within
http://social.technet.microsoft.com/Forums/windows/en-US/ca343a3c-c61e-4816-9a96-d973386db2e2/network-shows-as-unauthenticatedchanged-my-network-profile-to-public?forum=w7itpronetworking
Best regards
Meinolf Weber
MVP, MCP, MCTS
Microsoft MVP - Directory Services
My Blog: http://blogs.msmvps.com/MWeber
Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
Twitter:

Domain Logon fails using wireless LAN

Hi Sir,
I am setting up an ACS server to authenticate the wireless LAN users using PEAP MS-CHAPv2for one of my existing customer. They need to login to domain whenever they need to access to the network
On the wireless client's end, the OS is Xp and the client will use Windows XP wireless zero configuration. I have put in the necessary setting in order for it to support PEAP. I managed to get authenticated by checking against the passed authentications log found in the ACS.
However, the problem happens when I tried to reboot the desktop and Domain Logon appears, I was not able to logon to the Domain. I think I know the cause of the problem. It was because the wireless card is not authencated yet prior to the Domain logon screen.
How can I connect to the wireless network prior to the appearance of the Domain logon windows. There is no options for me to try in the XP wireless zero configuration to activate the wireless LAN before the Domain Logon windows comes out.
Thank you.
Delon

Even if still it does not work, ensure the following:
1) Change the logon credentials for the ACS services to use a domain administrator account. Often times the local member server administrator account does not have any rights on the AD.
a. Ensure the ACS services start with the Domain Administrator account.
b. Ensure you are able to log in to the server using this Domain Administrator account .
c. Ensure the Domain Administrator account (or the account with which the services start) have privileges to log on locally, Log on as a service and Act as part of the operating system.
2) Ensure the FQDN of all domain controllers is added to the DNS names.

Why do my firewalls only use the domain username and password for login and enable passwords, not a different enable password like my switches do? The RADIUS config looks the same...

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Issue:
Cisco firewalls require only one level of password i.e. the domain username and password are used for both logging in as well as reaching global configuration mode.
Background:
We have multiple Cisco network devices set up which authenticate to our Windows domain controller using NPS (Windows 2008 R2). The switches we have set up all function exactly as we would hope as they require your domain username and password to login to the device. They then require a separate password when you use the enable command, this is stored in Active Directory:
Switches:
Username:domain-username
Password:domain-password
SWITCH>enable
Password:enable-password-in-Active-Directory
SWITCH#
Firewalls (as they currently are):
Username:domain-username
Password:domain-password
FIREWALL>enable
Password:domain-password
FIREWALL #
With the firewalls however, they require your domain username and password first, and then your domain password again when using the enable command. I want the firewalls to use the enable level password that the switches currently use instead of the domain password again. The current configuration look like the following:
Current switch configuration:
aaa new-model
aaa authentication login default group radius local
aaa authentication enable default group radius enable
aaa authorization exec default group radius local
aaa session-id common
radius-server host 192.168.0.1 auth-port 1645 acct-port 1646
radius-server source-ports 1645-1646
radius-server key 7 1234abcd
Current firewall configuration:
aaa-server DC01 protocol radius
aaa-server DC01 (outside) host 192.168.0.1
aaa authentication ssh console DC01 LOCAL
aaa authentication enable console DC01 LOCAL
key 1234abcd
Any help would be great, thanks!

Cisco ASA works that way by design. You could remove "aaa authentication enable" and then you could use the "enable password" command to set your enable password.
But if you do that, then ASA would change your username to "enable_15". That would break Authorization and Accounting if you're using them. Let me clarify with an example
Firewalls :
Username:domain-username
Password:domain-password
FIREWALL>show curpriv
Username : domain-username
Current privilege level : 1
Current Mode/s : P_UNPR
FIREWALL>enable
Password:enable-password-from-running-config
FIREWALL #show curpriv
Username : enable_15
Current privilege level : 15
Current Mode/s : P_PRIV
If you're using Authorization and Accounting it's recommended to stick with your current behavior.

Open and Network-EAP authentication - difference in security?

As far as security goes, and assuming Radius authentication wil actually authenticate and allow users access to the wireless network (or not), it there any difference (once again, as far as security goes), between Open Authentication and Network-EAP as described below?
In any EAP/802.1x-based authentication method, you may question what the differences are between Network-EAP and Open authentication with EAP. These items refer to values in the Authentication Algorithm field in the headers of management and association packets. Most manufacturers of wireless clients set this field at the value 0 (Open authentication), and then signal their desire to do EAP authentication later in the association process. Cisco sets the value differently, from the start of association with the Network EAP flag.

1. Join process - comparable to connecting a cable in the wired network world. Usually "OPEN".2. Authentication - this verifies the client is who they claim they are because they possess a certificate (EAP-TLS), know the password or a PSK.3. Encryption with TKIP or AES - this is about protecting data as it is transmitted through the air AFTER authentication.
You are correct.
What confuses me when attempting to configure the Aironet I'm working with is the difference in terminology with the familiar choices I had in Linksys access points, something like this:- WEP- WPA- WPA-Enterprise- WPA2- WPA2-EnterpriseI thought WPA-Enterprise has to do with Radius and indeed I was able to create a test network in which a Windows XP laptop could connect via a Linksys access point, authenticating with EAP-TLS, with WPA-Enterprise selected on the AP. The Windows 2008 server was both a certificate authority, a radius (NPS) server and a domain controller.With the Aironet, I'm not sure what the equivalent choices should be, because, if you look at the link in my last post, there is a larger selection: WEP 40 bit, WEP 128 bit, TKIP, AES, combinations of what precedes and no reference to WPA or WPA2. I'm guessing TKIP = WPA and AES = WPA2.And while I can select "EAP" in the Express Security Setup tab, I cannot see where I would opt for EAP-TLS rather than PEAP or EAP-TTLS and so forth.I'm going to take a look at your blog now and see if that doesn't enlighten me further.
You are on track my friend keep the thinking going .... you are very close!
Some more foundation for you ...
WPA - Is PSK with TKIP
WPA2 - Is PSK with AES
WPA Enterprsie - EAP- ??? with TKIP
WAP2 Enterprsie - EAP - ??? with AES
??? = Your selected EAP type
Now, why dont you have to configure EAP type on the AP? Great question, lets break this down.
1. The AP or WLC for that matter doesnt care what EAP type you use . Why you ask?
When you configure 802.1X, there are 2 virtual ports . These are virtual and you do nothing to configure these. Once you connect to an AP and EAP starts, the ap BLOCKS ALL TRAFFIC except for EAPOL traffic. This is the ONLY traffic allowed past the until the AP / WLC receives a RADIUS SUCCESS. Once the AP/WLC sees this radius success it then switches virtually over to the controlled port and allows ALL your traffic to pass.
2. With that being said, your client is only passing traffic through the ap and wlc. The ap / wlc doesnt care what EAP you are using. Your client is talking directly to the radius server at that point. The AP/WLC at this point is only a pass through, nothing more.
Does that help ?
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin

Server 2012 std not able to see Domain, DC and DNS on Win SBS 2008 std Domain

Hi There
I have a HP ML 110 G5 SBS 2008 std server as my DC on my network. I recently added a HP Microserver running Server 2012 std (with no roles or features installed) to act solely as a file server for a 3rd party program as the program was not running efficiently
on the main server.
The problem I am having now is that the 2012 server keeps falling off the domain and cannot contact DNS server. I have also had to re-enable remote desktop several times. It also shows the 2012 Server as being on a private firewall profile and not on the
domain firewall profile but I suspect that this is part of the same problem.
the resulting problem that this is causing is that the local machines that need to contact an SQL database on the 2012 fileserver intermittently either time out or are very slow to connect.
So far I have tried:
Switching from Static IP to DHCP.
Re-adding the server to the domain.
Stopping and restarting DNS services on the DC.
Checking physical Network connections and routing.
Putting the 2012 server into the same Organizational Unit as the 2008 DC.
Has anyone else encountered this problem when adding a 2012 server to a 2008 domain? I have a feeling that the solution is probably something simple that I've overlooked, but I can't think what. Any help would be greatly appreciated.
Regards
Russ
Also, as some additional info -
Event viewer gives the following errors:
Group Policy Error:
Log Name: System
Source: Microsoft-Windows-GroupPolicy
Date: 2015-04-27 01:17:51 PM
Event ID: 1129
Task Category: None
Level: Error
Keywords:
User: SYSTEM
Computer: [SERVERNAME].[DOMAIN].local
Description:
The processing of Group Policy failed because of lack of network connectivity to a domain controller. This may be a transient condition. A success message would be generated once the machine gets connected to the domain controller and Group Policy has
successfully processed. If you do not see a success message for several hours, then contact your administrator.
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-GroupPolicy" Guid="{AEA1B4FA-97D1-45F2-A64C-4D69FFFD92C9}" />
<EventID>1129</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x8000000000000000</Keywords>
<TimeCreated SystemTime="2015-04-27T11:17:51.111942100Z" />
<EventRecordID>19056</EventRecordID>
<Correlation ActivityID="{C0CBAF2B-1E93-49C0-B910-069AE43F74B2}" />
<Execution ProcessID="732" ThreadID="1336" />
<Channel>System</Channel>
<Computer>[SERVERNAME].[DOMAIN].local</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="SupportInfo1">1</Data>
<Data Name="SupportInfo2">1548</Data>
<Data Name="ProcessingMode">0</Data>
<Data Name="ProcessingTimeInMilliseconds">0</Data>
<Data Name="ErrorCode">1222</Data>
<Data Name="ErrorDescription">The network is not present or not started. </Data>
</EventData>
</Event>
DNS Error:
Log Name: System
Source: Microsoft-Windows-DNS-Client
Date: 2015-04-27 04:54:58 PM
Event ID: 8015
Task Category: (1028)
Level: Warning
Keywords:
User: NETWORK SERVICE
Computer: [SERVERNAME].[DOMAIN].local
Description:
The system failed to register host (A or AAAA) resource records (RRs) for network adapter with settings:
Adapter Name : {3DDD0E46-D879-48C0-9DF6-5FAC0F1A56C4}
Host Name : [SERVERNAME]
Primary Domain Suffix : [DOMAIN].local
DNS server list :
192.168.2.10
Sent update to server : <?>
IP Address(es) :
192.168.2.15
The reason the system could not register these RRs was because the update request it sent to the DNS server timed out. The most likely cause of this is that the DNS server authoritative for the name it was attempting to register or update is not running
at this time. You can manually retry DNS registration of the network adapter and its settings by typing 'ipconfig /registerdns' at the command prompt. If problems still persist, contact your DNS server or network systems administrator.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-DNS-Client" Guid="{1C95126E-7EEA-49A9-A3FE-A378B03DDB4D}" />
<EventID>8015</EventID>
<Version>0</Version>
<Level>3</Level>
<Task>1028</Task>
<Opcode>0</Opcode>
<Keywords>0x4000000000000000</Keywords>
<TimeCreated SystemTime="2015-04-27T14:54:58.599130300Z" />
<EventRecordID>19105</EventRecordID>
<Correlation />
<Execution ProcessID="856" ThreadID="952" />
<Channel>System</Channel>
<Computer>[SERVERNAME].[DOMAIN].local</Computer>
<Security UserID="S-1-5-20" />
</System>
<EventData>
<Data Name="AdapterName">{3DDD0E46-D879-48C0-9DF6-5FAC0F1A56C4}</Data>
<Data Name="HostName">[SERVERNAME]</Data>
<Data Name="AdapterSuffixName">[DOMAIN].local</Data>
<Data Name="DnsServerList"> 192.168.2.10</Data>
<Data Name="Sent UpdateServer"><?></Data>
<Data Name="Ipaddress">192.168.2.15</Data>
<Data Name="ErrorCode">1460</Data>
</EventData>
</Event>

Can you post an ipconfig /all from the server and the DC?
Robert Pearman SBS MVP
itauthority.co.uk |
Title(Required)
Facebook |
Twitter |
Linked in |
Google+

Can I have two Domain in one network?

I have two Server in my office in same network.
Server A is Active Directory / Domain Server. Certain user join domain and connect to this server.
Server B is File Server. The other user just use Workgroup. But now this server want to Up Domain to be Domain Server.
But user that connect to the domain Server A will not connect to domain server B and user connect to domain server B will not connect to domain server A.
Is there any problem if I setup two domain in one network?
Please Advise.

Domains are logical structure of your network. Yes you can create two domains in the same network. One thing you should consider in this scenario is trusts between your domains. By default separate domains have not any trusts between each other and you should
establish trust manually if you would like to have users in A authenticated in domain B.
Regards.
Mahdi Tehrani Loves Powershell
Please kindly click on Propose As Answer or to mark this post as
and helpfull to other poeple.

Windows 8.1 Group Policy to Force Domain Logon as Default?

I recently purchased a new Windows 8.1 computer for use in our organization. The default logon option for the device is for a Microsoft Account (the default username field prompt is for an e-mail address, rather than for a username.) However,
I would prefer that the default logon option be for a Windows domain account logon, so that users don't have to click the "Sign-in options" link and select "Local or domain account password" each time they need to log onto the computer.
I have learned that setting the "Interactive logon: Do not display last user name"
policy (located under Computer Configuration / Policies / Windows Settings / Security Settings / Local Policies / Security Options) to
Disabled allows the domain logon option to be retained across sessions. However, I would prefer to keep this option set to Enabled so that the previous user name is not displayed.
Does anyone have any suggestions on how the default logon option can be forced to a domain logon, while still suppressing the display of the last username?

Hi Arowitv,
According to your description, we can use the following policy to check the result.
Computer Configuration\Windows Settings\Security Settings\Local Policies\Security Options:
Accounts: Block Microsoft accounts
Click this option, and select" Users can't add or log on with Microsoft account"
Note: Selecting this option might make it impossible for an existing administrator on this computer to log on and manage the system.
Computer Configuration\Administrative Templates\System\Logon :Assign default domain for logon
Set the option to Enabled, and add the Default Logon domain.
Hope this helps.
Regards,
Kelvin Xu
TechNet Community Support

Implementing Sites for a new Single Domain Environment and effects on Exchange

Copied from the Active Directory forums as the suggestion of replies.
I didn't find exactly what I was looking for so decided to create my own question to get some direct feedback.
Currently we have a single domain environment with two domain controllers located at two separate sites. When the domain was first set up, no configuration was done in the Sites and Services module for Active Directory. The two domain controllers we have are
currently located in the Default-First-Site-Name container. We do not have any subnets configured with the Sites and Services module.
These two domain controllers are located at two different sites with different IP schemes and the sites are connected with a high speed site-to-site VPN. We also have 2 satellite offices with their own IP schemes as well with more offices to come. In the future
domain controllers will be placed at these satellite offices which are connected with a slower site-to-site VPN to the main offices.
All replication and network functions are working well now, but I would like to know what the effects would be and what to watch out for if I create sites for our environment. I am particularly concerned about our Exchange 2010 server and need to make sure
that the change will not disrupt communications between it and the domain controllers.
I would like to create a site for each of our locations and link the subnet to that site now so that when we install the domain controllers the configuration is ready.
Any suggestions or input is highly appreciated thank you in advance.

Exchange will be an issue only if your Exchange servers span sites when your new Windows sites are created. If you have Exchange servers all in a single location, adding sites to your Windows forest will cause no issues. However, if you have
Exchange servers in both locations, as soon as a new site is defined for an Exchange server in a separate location from your other Exchange servers, you will start having issues. Let me give some examples so you can see what problems might occur:
Two datacenters, one Windows site, Exchange mailbox servers in both locations (primary and DR), but hub and CAS roles only in the primary datacenter:
In this situation, as soon as your second site is defined, the server in the DR datacenter will no longer be receiving mail - there is no hub to deliver it - and users will no longer be able to access their mailboxes - there is no CAS to support them.
Solution: Add hub and CAS to second datacenter and all is well with the world.
Two datacenters, one Windows site, Exchange multirole servers in both locations (primary and DR), but CAS Array defined:
Now we have a little bit better setup, since we have all roles in both locations. However, the CAS array in the primary site isn't going to be able to support your client connections in the DR site - so users will be connecting directly to the CAS
servers in the DR site (not optimum). Solution: Define a second CAS array for the DR site, with its own load balancer and configure the databases in your DR location to use that CAS array as the RPC Client Access Server.
There are other oddities, but as you can see, there will definitely be issues if your Exchange servers aren't all in the same location and you start defining Windows sites ...

Autodiscover, domain controllers, and certificate errors

I have just deployed and Exchange 2013 server in one of my sites. I'm having tons of issues with it, but one issue I'm having trouble thinking through goes like this:
All users have email addresses that are [email protected] Domain.com is our internal domain name and also a public domain. Now, in a Windows environment, if you were to nslookup domain.com within our network it
will resolve to any one of the domain controllers. On our infrastructure master DC there is an IIS website, with SSL, that handles certificate services for our internal CA.
Here's my problem: When a user opens Outlook and autodiscover attempts to find their Exchange connection info it first tries to reach the site
https://domain.com/autodiscover/autodiscover.xml. If that PC happens to resolve domain.com to the DC that has our certificate services website on it then the Outlook client sends a certificate error.
If the client is prior to Outlook 2013, the mailbox configuration just halts and throws an error.
What do I do to prevent this?

Hi,
Yes, we can have the following “switchers”
PreferLocalXML
ExcludeHttpRedirect
ExcludeHttpsAutoDiscoverDomain
ExcludeHttpsRootDomain
ExcludeScpLookup
ExcludeSrvRecord
ExcludeLastKnownGoodUR
Thanks,
Simon Wu
TechNet Community Support

Domain Logon and Networks

Similar Messages

Maybe you are looking for