Driver Installation problem for Probook4530s

I recently got my laptop fixed and now i can not seem to access my bluetooth or use a wired LAN connection, i noticed that some of my drivers have been missing so i tried installing the drivers but they dont finish to install.
My Connection manager is saying bluetooth is disabled by device manager and there is no wired lan option being displayed, which drivers should i install to fix these two problems. I am running WIndows 7 Profesional 32-Bit and i have never changed it.

Driver for Wired LAN
http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5060884&sp...
Driver for bluetooth
http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5060884&sp...
There are multiple bluetooth drivers listed. Hence, if the above bluetooth driver doesnt fix the problem then you can find the exact driver by the device ID/hardware ID from device manager.
if unable to fix, buzz me in skype... mohammad.jahangir89

Similar Messages

G510 audio driver installation problem on Windows 8.1

I've just received my brand new Lenovo G510 and installed Windows 8.1 Pro 64-bit onto it.
Most of the drivers from the attached CD installed without any problems (though I was quite surprised that no newer versions were available on the Support wrbpage) but I can't install audio driver.
Apparently this series is equipped in either Conexant or Realtek audio chips and the provided setup application is desigend to detect the correct chip and run the appropriate driver installation program.
The problem is that setup is not working for me. All I receive is the notification "This utility can not be used on this machine". Since there are no "orphan" audio devices in the Device Manager, I can't really tell which audio chipset is installed in my machine. I don't want to install both dirvers as it may just cause confilcts.
How can I say which audio chipset is installed and install the correct driver?
Solved!
Go to Solution.

hi mikolajek,
Welcome to Lenovo Community Forums!
Under Device manager
You should look for your Audio
Normally it stays under Sound and gaming controller,
And if no driver is installed in shows as High Definition Audio
Right click on it and select Properties
Go to the Details TAB
change the Value to Hardware ID then check the details
ex. PCI\VEN_14E4&DEV_4727&SUBSYS_051014E4&REV_01
Get the 4 digit after VEN and DEV
Ven is the Vendor and Devi is the Device
Go to PCI database and do a search for the VEN
Then search for the DEV and youll know that device
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

HP Laserjet PRO MFP M125nw; Wireless Driver installation problem in Win 8.1

Product name : HP Laserjet PRO MFP M125nw, product nr CZ173A
US Operating system: Dual Boot:   Win Vista home premium (32 bit) / Win 8.1 pro (32 bit)
The printer was installed under Vista in September 2014 and was and still is wireless printing and scanning without a problem.
Recently I tried to install the printer (wireless) under Win 8.1 and I downloaded the latest Full Feature software from HP.nl.
During installation the software installation package could not find the printer and installation was aborted.
I ran the printer self test / Configuration. The network Info and product info sheets were without errors. A ping to the IP address of the printer was without a loss. The firewall indicated that HP software is accepted.
Off course I read everything on HP about this problem I followed every advice and repeatedly gave it a try. I even installed the usb cable solution ( USB was working ok) followed by your change connection instructions, but all in vain.
To my surprise HP was able to find my printer when I checked on http:// www.hp.com/cgi-bin/hpsupport/index.pl. However the printer was found in my local network as a HP Laserjet Pro M1132 multifunctional printer with product nr stars 3NW-01 which is not correct, however the found serie nr. of CNB7G3RC78 was correct.
The print and scan doctor made some changes to the software and after that I was able to print wirelessly, however the Scan doctor button did not react at all and using the program was not possible further. Starting the program again gave the same result.
Conclusion:       In Vista: HP wireless print and HP wireless Scan is working fine
                        In Win 8.1: HP wireless print is OK, HP wireless Scan cannot be installed !????
                        In Win 8.1: Windows Printer driver and Win Fax& Scan driver both wireless working ok
Remark: Reading the display is difficult in dim lit areas. The on / off button is brightly lit and this light should be used to enlighten the display instead.
A solution for the scanning problem would be appreciated.
Kind regards
JWAH

Hi @JWAH , and welcome to the HP Forums!
I understand you're experiencing driver issues. I'd like to help!
I would suggest Uninstalling the Printer Software.
Once it is uninstalled, I would suggest putting your system into clean boot mode within the Microsoft configuration. You can do so by following this document: How to perform a clean boot in Windows.
Once the computer is in clean boot mode, I would suggest reinstalling the HP LaserJet Pro MFP M125/126 Series Full Software and Drivers.
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

HP Pavilion dv2718us Notebook PC - Driver Installation Failed for Auto:

Sound has gone on my laptop. Speaker icon with red circle & white X in toolbar. Says NO AUDIO DEVICES ARE INSTALLED. Downloaded new driver. I now get failed message - Driver Installation Failed- Could not find Media Device for this driver. What do I do now?

Hello @Geiss,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how you are not able to get the sound to work on your notebook computer, and I would be happy to assist you in this matter!
To restore the audio to your notebook, I recommend following this document on No Sound from Speakers (Windows 8). This should help ensure that the drivers on your computer are correctly installed.
For further assistance, I will need to know:
If you can provide a screen shot of your Device Manager outlining this error message.
The Product Number of your notebook computer.
The version of Windows you have installed on your computer.
If your computer has completed all of its important Windows Updates.
If you have updated your HP drivers using the HP Support Assistant.
If this is an on-going, or recent issue.
If you have installed any new software or hardware recently to your computer.
Please re-post with the results of your troubleshooting, as well as the requested information above. I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

My problem is very simple......firefox wont allow me save my downloads to any other location than my c drive....for example i have gone into options and set sav

''locking this thread as duplicate, please continue at [https://support.mozilla.org/en-US/questions/986549 /questions/986549]''
my problem is very simple......firefox wont allow me save my downloads to any other location than my c drive....for example i have gone into options and set save downloads to my e drive....but still firefox keeps saving them to my c drive....i have 4 internal hard drives in my rig....and have tried saving downloads to them all.......why this is happening i cant understand....i have tried lots of suggestions....and have re-installed firefox multiple times

hello, there's a general regression in firefox 27 that won't allow files to download directly into a root drive. please try to create a subfolder (like ''E:\Downloads'') and set this as default location for downloads...
also see [https://bugzilla.mozilla.org/show_bug.cgi?id=958899 bug #958899].

T500 Driver crash problem, for all upgrading owners

To all the T500 Owners who have upgraded to windows 7. There is one major problem hindering a lot of t500 owners. Someone mentioned earlier in this thread to download the catalyst 9.9 drivers from ATI. Everything else has worked great and all the drives have automatically been updated smoothly.
They install properly but after a restart this is what happens as mentioned by another user
"Hi I have a big problem with my lenovo T500. I installed Windows 7 RC x64 to my lenovo T500 (2082-53G) and when I install the ATI catalyst beta driver v9.9 from ATI's homepage, my computer freezes at startup (some activity on HD but I can't move my mouse and many processes faile to start at boot). I'm not the only one facing this problem: Lenovo T500 Thinkpad - WDM Radeon 3650 Driver Update Causes Screen to Freeze"
I have the exact same problem.... have formatted twice already, gone into safe mode, theres no getting around this problem.
Any help? I have the 32 bit version of windows 7 enterprise 90 day trial.
I know we might not be able to swtich the graphic cards, but at the very least we should be able to pick one in bios and be forced to use that. At this point its not even allowing me to install the discrete driver.

Hi SuperWoofer,
Thanks for your sharing. You're very helpful indeed! =)
Regards,
Cleo
Message Edited by Cleo_Lenovo on 06-12-2009 11:43 AM
WW Social Media
T61, T410, x240, Z500, Flex 14
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
How to send a private message? --> Check out this article.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Computer iMac7,1 has been giving sundry problems for some time. Within the last six weeks I have reinstalled the OS (Snow Leopard), without affecting the overall contents of the hard drive. ±3 weeks later the problems became more serious and I again reins

Computer iMac7,1 has been giving sundry problems for sometime. Within the last six weeks I have reinstalled the OS (Snow Leopard),without affecting the overall contents of the hard drive.
±3 weeks later the problems became more serious and I againreinstalled the OS and installed OS 6.6.7 from the internet.
I used the option to restore from the external backup driveand went back some time as it was my intention to reinstall individualcomponent in an attempt to find out where the problem might lie. This hasintroduced an entirely new problem! If I open Time Machine from the desktop itappears that all backups from late 2009 to June 2011 are intact. But, in thiscase there are none of the restore functions &c on screen. The latter areonly shown if Time Machine is opened from the menu bar or from the dock but, inthis case, available are only backups in late 2009!
I also opened the Apple Hardware Test in an attempt toestablish the nature of the problem. The ‘quick’ version said there’s nothingwrong; the more detailed one reported “Error detected, 4HD/11/40000004.” I haveagain tried to employ this test but nothing I do can induce it to open!!!
What to do? I need help urgently and would appreciate anyadvice that offers solutions to the problem.

To check your S.M.A.R.T status open disk utility and click on your drive and then click on the info icon.

Hard drive beachball problem for the 17"

Ok, so I know that there is already a few posts about this issue, (including the very large 96 page one) but I wanted to start a post for those of us with a 17" MBP that are having the same issues.
I was on the phone to a senior technician at Apple (Australia) today for about 2 hours trying to sort out this problem. Firstly he was a bit hazy about the issue to begin with assuming it was a RAM paging issue. Seriously, this thing has 4gb of ram, I think you would have to running so much stuff at once for it to legitimately run out of ram. I'm a web developer/designer so I can push the machine reasonable hard sometimes but I get the beachballs even when I only have safari and mail open. This is the fastest (stock) laptop Apple have ever produced, surely it can handle a bit of stick.
So I suggested it could be the hard drive/firmware etc and mentioned about the large amount of people on here with the exact same issue. After looking into some internal documentation he noted that there was indeed similar problems happening around the place but he seemed convinced that this only applied to 13" and 15" models and that the 17" never got the 1.7 firmware update.
After looking at the firmware page: http://support.apple.com/kb/HT1237 it seems maybe he's right. I can't see my boot ROM version there anywhere (MBP52.008E.B05) The mid 2009 model 17" isn't on that list.
Whilst my friend at Apple is reasonably sure that my issue is software related and wants me to watch the console when Im having the freezing, I'm positive that I'm having the exact same problem as the 13 and 15s.
Can other people with 17" MBP that are having the same issue please post here so that we can begin to build a case for Apple to acknowledge the problem for our model too? Please add whether you have installed a 3rd party hdd or whether you are having the problem despite only having the stock hdd like me.
Thanks guys.

soniktrooth, count me in. I am experiencing the same problem myself - I just recently posted over in the mega forum here: http://discussions.apple.com/thread.jspa?messageID=10222616#10222616
There is a chance that the hard disk could be at fault I guess, but the symptoms of this problem for me are remarkably similar to what I've read in the 96 page post, and on the macrumors forums. To summarise:
* the problem usually begins when I'm playing iTunes all day, and then I'll go to save something, say in TextMate, and then iTunes stops playing.
* Any app you then try to switch to while the freeze is there will then just beachball itself.
* Like you, I know this is something out of the ordinary, since iTunes rarely stops playing music, and hardly ever did on my 4 year old G5.
* I can make the problem go away by restarting and zapping the PRAM. All day today my computer has been fine, but I suspect that sometime tomorrow it'll probably start all over again.
* My drive is a factory Hitachi 5400 RPM drive... what do you have?
* My boot ROM version is the same as yours too.
* I have 8GB of RAM in this machine, so I'm pretty **** sure it's NOT a paging issue for me. paging issues never last 20-30 seconds though, that's absurd if anyone claims that is the cause... also, the hard disk doesn't really crank noticeably while the freeze is there.
I'm wondering if there was some sort of revision too for this model that may be causing this. Seems unlikely that Apple would have changed the motherboard between the january model and this one, but I'm not sure if this is absolutely confirmed...

Regarding USB Driver (OMAP1710) Problem for Belkin...

Dear All,
I've been trying to update my Belkin Skype Phone (F1PP000GN-SK) from version: 1.1.0.10 R20 to version: 1.1.0.22R20 from the belkin support site.
But the problem is when i connect the USB cable to my Windows 7 (32-bit) laptop i get a pop-up saying "Missing OMAP1710 USB driver'
Kindly someone help me pls.

I believe the original drivers packaged with the Belkin installer/flasher may work on the 32-bit version of Windows 7, but will not work with the 64-bit version. Since I do own this phone, I decided to resolve this problem for myself as well. Even though they are not available from Belkin, I was able to track down and extract/modify the latest drivers/inf for this phone.
You will need to extract and browse to these files using device manager to get the device installed. You will get a warning about the files being unsigned, proceed anyway to finish installing the device. Before flashing you will either have to disconnect/reconnect the phone or press the "#" key to refresh it. Once it starts flashing DO NOT disconnect the device. I've reflashed my phone several times without issue.
If the reason behind upgrading it is to resolve a freeze, the upgrade may not fix it. You would want to downgrade to the original release. That will generally resolve the issue. After that, you can flash it to the latest release.
My version of the latest drivers for Windows XP/Vista/7/8 (32/64-bit unified inf) are available from the following location:
http://pcdust.com/Downloads/OMAP1710/OMAP1710.zip

Driver problem for linux

i want to know that which linux is suitable for my laptop. please tell me. i installed ubuntu 14.04
but there were problem for touch pad. i installed red hat linux but touch pad didnot support. so which linux is suitable for my laptop?? please solve this....

I have Kubuntu 14.04 and have had no trouble. I also have a Synaptics touchpad and it works great.
I have never had to use it but there is a Linux project for Synaptics support:
http://cscott.net/Projects/Synaptics/

Hi all, I upgraded my MBP to Lion , but on the screen where i need to type my password, click on my photo and it does not appear the place for me to type my password and it stay stuck there. Can anyone solve this problem for me?

Hi all, I upgraded my MBP to Lion , but on the screen where i need to type my password, click on my photo and it does not appear the place for me to type my password and it stay stuck there. Can anyone solve this problem for me?

Reboot the machine holding Command and r keys down, you'll boot into Lion Recovery Partition
In there will be Disk Utility, use that to select your Lion OS X Partition and Repair Permissions.
After that is done reboot the machine and see if you can log in.
If not repeat the above steps to get into Lion Recovery, get online and reinstall Lion again, it will overwrite the installed version and hopefully after that it wil work.
Reboot and try again.
If not follow my steps to create a Snow Leopard Data Recovery drive, then option boot from it and grab a copy of your files off the machine.
Then reinstall all your programs onto the external drive like setting up a new machine, then use Disk Utility to erase the entire internal boot drive (select the drive media on the far left, not the partiton slightly indented) format Option: GUID , 1 partition OS X Extended and then use Carbon Copy Cloner to clone the external to the newly formatted internal drive. Once that is finished reboot and disconnect the external drive.
Once you go that, boot into Snow Leopard and update to 10.6.8, use the AppStore and option click on Purchases and download Lion again and install.
Lots of work, but there is no Lion disks.
https://discussions.apple.com/message/16276201#16276201

Help me identify problem for slow export on a powerful machine

Hi,
I am exporting an interview in Premiere Pro CC. It is 1:45:00 long and it has been 20 hours since, but the export is only 94% complete.
Project & Footage:
The footage is a combination of DSLR footage - 5D Mark III, GH3, 650 & 550D.
The edit is all straight cuts with: {a} Color corrector on each clip to match all cameras {b} NEAT - reduce noise on around 10% clips {c} Sharpen (10-30) & {d} An adjustment layer overall with a 3-way color corrector for a simple color grade.
Hard Drives:
E: SSD-RAID for the source footage (Samsung 840 SSD on RAID-0)
D: SSD for previews and cache (Samsung 840 Pro)
C: SSD for Windows, Adobe CC & all programs (Samsung 840 Pro)
G: Simple Seagate Hard disk for Export (used to be a 3 disk RAID but 2 drives crashed some time back)
Other Machine Spec:
Intel i7-3930K overclocked by 10%
64GB RAM
GTX-770 GPU
This is my longest project to date in terms of total time, but last time I did a 1:00:00 project, took around 2 hours not 20.
My concern is I need to understand where the bottleneck is?
My CPU is hardly working a sweat - 40% at max
My RAM is plenty - being used 40-70%
GPU is not even being used in anything (see it at 0%)
Disks (which I was sure was the bottleneck) barely cross 10MB/s
Checked the "power options" in Windows also - everything is set to maximum performance.
It was a big mistake not to send it to Media Encoder as I could have continued editing a different project. Biggest. Mistake. Ever! (no idea why Adobe does not make it a default behaviour?)
I am fairly new to the industry and till last year was using a MacBook Pro until I started getting demanding projects.
I want to know is this normal? If I had used NEAT video for 100% footage then probebly I could have understood this, but its used for only 1/10th of thr footage and I have used NEAT before (but on After Effects CS6) on my Macbook pro (nowehere near as fast as my current machine) and it only added a small overhead - nothing of this sort.
I expected maybe 3 hours to export this 90-100 min seqeunce, not over 1 day.
So what could be the reason? Why isn't one of the above (CPU, RAM, Disk, GPU) at 100%?
I expected 1 of these to be the bottleneck but nothing is crossing 50% even when it should be on full blast.
I dread what if there is small tweak required in the edit once its complete. This video is due on Monday, I would have to reencode for 24 hours.
Please experts - let me know your thoughts. Could it be that Creative Cloud Windows is slower than CS6 Mac & its not a hardware problem?
I am sure I am missing some hardware that is causing this bottlenck. Attaching resource Monitor screenshot (let me know if I should use some benchmark software for you guys to get more information).

UPDATE: My export crashed (and heart sank) after 96% (25 hours). Win7 restarted. I have no clue why (If someone has any tip how to seach logs/dump in Windows to find a reason how, please let me know - I was worried about CPU temperature but that was around 40 deg, I was monitoring it.)
Anyways, so I used Media Encoder now (instead of direct export in PrPro) and made 2 changes:
1. I unchecked "Render Maximum Depth" just as it is in the the default Youtube 1080p@24p preset (but kept the keyframing distance at 24 instead of 72 which is default).
2. From VBR - 2 Pass, I made it CBR
Its been 15 min I started the export and the video is 20% encoded already, with remaning time just 00:30 min.
Now I am flabergasted.
Did not using maximum depth & VBR- 2 pass alone make such a difference? From 30 hours to 1 hour? I am still using all the video effects and absolutely no change to the edit.
I am seeing 2 differences the way my machine is working:
1. Is Adobe somehow using some old renders it did for the last export? I am using disk utility and it is refering to original source files and some "Media Encoder preview files" which I think it was not using before (could be wrong)?
So all that hard work it did for 25 hours is being utilized and if I do such a project again it will take me 30 hours again. Right?
2. GPU is now being used (and to good effect). How is GPU being used now? I am not scaling or using any fancy effects. Just Neat Video, 3-way color corrector & Sharpen.
This was before (export done in Premiere Pro directly):
And this is now:
Very sad that no one (even from the Adobe Staff) has replied to my post. Did I say something inappropriate or TMI?
C'mon guys I am on the Creative Cloud - show me some love

"This drive is not ready for use; it's door may be open ..."

Hi.
I recently updated to itunes 7, and then had an issue with a corrupt file on the i-pod (which resulted in chkdsk hanging itself at 27%, always). So I restored the i-pod and that took care of that - chkdsk now says it's fine.
However - it is also empty. My machine and i-tunes recognize it fine upon start-up; however, a short while into a full synch to get my library back on the i-pod, I invariably get the following error message:
"The drive is not ready for use; it's door may be open. Please check drive \Device\Harddisk\DR 3 and make sure that a disk is inserted and that the drive door is closed." The message comes with the options "cancel, ignore and continue", yet the latter two don't make a difference, and even if I choose cancel, itunes keeps trying until it eventually crashes.
This always happens after itunes has synchronized about 1.13 GB (out of 18.55 available).
As far as I can tell, both my system and the iPod are up to date (itunes and windows update say so, anyway). E: is unequivocally and exclusively allocated to the i-pod; changing the settings from "optimize for quick removal" to "optimize for performance" has made no discernible difference.
Any ideas would be very much appreciated.
Thanks.
DELL Inspiron 4150 Windows XP

Hullo ...
let me follow up on this again. I've followed your advice, de-installed spybot, no change. I looked through the windows support help base, nothing. While trying out different things, I started getting a "delayed write failed" message, and I did some things they suggested (including adjusting the registry - me, adjusting the registry!)and it went away, and now all I get is the "open door" message again.
That is: everything works absolutely fine, I plug in the i-pod (latest version i-tunes and i-pod is up to date), it's recognized instantly by the explorer as well as i-tunes. I've run all scans you can possibly run on it, and it is fine (no corrupt files, nothing). I've restored it twice through i-tunes, twice through the explorer. I've changed the drive letter.
It starts the synch fine (it's still almost empty after the last restore), but at some point, I get the error message. Interestingly enough, *up to* that point, it'll synch fine - I can disconnect it and play on it whatever's been synched thus far. I can also modify my i-tunes settings and preferences, all of which i-tunes will recognize and adhere to. It is just unwilling to put more than 1GB of stuff onto my 20GB i-pod.
Something I've noticed is that it is sometimes indicating apparently faulty charges in the beginning (though that is quickly corrected once the synch starts), as in, it'll recognize a certain amount of audio files, but also claim a random amount of "other" files, which should not be there (apart from the 30MB or so of genuine i-pod software).
Anyhow. I haven't seen any solutions to this on the forums or in the apple help files, but people appear to be having this problem still. Any ideas or input would be very much appreciated ...
Thanks.

"The drive is not ready for use; its door may be open. Please check drive \

3G IPOD problems which are driving me mad and i can see others have had the same problem but i can't find any solution written down.
Basically my IPOD either freezes after a couple of songs or it downloads about 6Gb (of 40) and the freezes with the following message:
"The drive is not ready for use; its door may be open. Please check drive \Device\Harddisk2\DR6 and make sure that a disk is inserted and that the drive door is closed"
I've tried re-setting, installing etc but no luck. Any suggestions/solutions?
Laptop - Packard Bell Notebook Windows XP

Hmmmm. I'm not sure how to explain this.
You need to change the Drive Letter for your iPod.
You should be able to connect your iPod then open Windows Explorer and right click on your iPod(which seems to be Drive E:) and change it to a different letter (like H).
If you haven't enabled disk use for your iPod it probably won't appear in Windows Explorer.
To enable disk use: connect iPod, open iTunes. Open Preferences and select the iPod tab. Choose "enable disk use."
Once you've done all that, try resyncing.

Lenovo ideapad yoga 13 pci data acqusition and signal processing center for problem for windows 8

Link to picture
hi everyone,
find original w8 cd and then i installed, when i was installing
i deleted all recovery and other partition, i did not think what can i do,
but then i activated windows and installed all driver, but i taking
after all drivers it stayed
2''unknown devices''
and when i rebooted, it says, usb device not recognized'' and also
''pci data acquisition and signal processing center'' devices problem for windows 8. and touchscreen not working.
i read related for w7 same problem, but what i will do now ?
thanks.
Moderator note; picture(s) totalling >50K converted to link(s) Forum Rules

hi adilsefaersan,
Welcome to Lenovo Community Forums!
By opening your Device Manager right click on one unknown device and choose properties,
>On the properties windows Click on the Details Tab, on the property drop down Choose hadware IDs
> then copy the value and post back here whats on the Value pane
Do it for all those unknown Device and Post here the Value of the hardware ids
also can you share your Windows Version and bit type so we'll knwo the correct download page for you
Thanks and Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Driver Installati​on problem for Probook453​0s

Similar Messages

Maybe you are looking for

Driver Installation problem for Probook4530s