Dual screen, one normal res, one zoomed in

Hey All,
I want to set up an additional screen and I want it to mirror what is on my main display BUT I want it to be zoomed in (similar to how things appear when u hold down ctrl and zoom in with the mouse. This way, I can tweak the more fiddly controls within Logic with ease.
Has anyone come across an app or a setting etc that might allow this to happen?
Cheers,
Sam

Try *Universal Access* , it is in your *System Preferences* . Not sure how it behaves with dual screens, should work though.
!http://farm5.static.flickr.com/4027/4280804567026a573156o.png!
regards, Erik.

Similar Messages

Any one help me with dual screen?

I am trying to get my LCD monitor work, which is plugged in VGA.
However, when i using "xrandr --output VGA --auto" to set it up, i get this failure "xrandr: cannot find crtc for output VGA"
i am using intel graphic card, and the result of "xrandr -q --verbose" is as follows,
Screen 0: minimum 320 x 200, current 1440 x 900, maximum 2960 x 1024
VGA connected (normal left inverted right x axis y axis)
Identifier: 0x3b
Timestamp: 1278799
Subpixel: unknown
Clones:
CRTCs: 0 1
1360x768 (0x41) 84.8MHz -HSync +VSync
h: width 1360 start 1432 end 1568 total 1776 skew 0 clock 47.7KHz
v: height 768 start 771 end 781 total 798 clock 59.8Hz
1152x864 (0x48) 81.6MHz -HSync +VSync
h: width 1152 start 1216 end 1336 total 1520 skew 0 clock 53.7KHz
v: height 864 start 865 end 868 total 895 clock 60.0Hz
1024x768 (0x4c) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
800x600 (0x51) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
640x480 (0x56) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 59.9Hz
1440x900 (0x3f) 101.6MHz
h: width 1440 start 1488 end 1520 total 1824 skew 0 clock 55.7KHz
v: height 900 start 903 end 909 total 926 clock 60.2Hz
LVDS connected 1440x900+0+0 (0x3f) normal (normal left inverted right x axis y axis) 0mm x 0mm
Identifier: 0x3c
Timestamp: 1278799
Subpixel: horizontal rgb
Clones:
CRTC: 1
CRTCs: 1
PANEL_FITTING: full
supported: center full_aspect full
BACKLIGHT_CONTROL: kernel
supported: native legacy combination kernel
BACKLIGHT: 15 (0x0000000f) range: (0,15)
1440x900 (0x3f) 101.6MHz *current +preferred
h: width 1440 start 1488 end 1520 total 1824 skew 0 clock 55.7KHz
v: height 900 start 903 end 909 total 926 clock 60.2Hz
1440x900 (0x40) 106.5MHz -HSync +VSync
h: width 1440 start 1520 end 1672 total 1904 skew 0 clock 55.9KHz
v: height 900 start 903 end 909 total 934 clock 59.9Hz
1360x768 (0x41) 84.8MHz -HSync +VSync
h: width 1360 start 1432 end 1568 total 1776 skew 0 clock 47.7KHz
v: height 768 start 771 end 781 total 798 clock 59.8Hz
1152x864 (0x42) 143.5MHz -HSync +VSync
h: width 1152 start 1232 end 1360 total 1568 skew 0 clock 91.5KHz
v: height 864 start 865 end 868 total 915 clock 100.0Hz
1152x864 (0x43) 121.5MHz +HSync -VSync
h: width 1152 start 1216 end 1344 total 1568 skew 0 clock 77.5KHz
v: height 864 start 865 end 868 total 911 clock 85.1Hz
1152x864 (0x44) 119.7MHz -HSync +VSync
h: width 1152 start 1224 end 1352 total 1552 skew 0 clock 77.1KHz
v: height 864 start 865 end 868 total 907 clock 85.0Hz
1152x864 (0x45) 108.0MHz +HSync +VSync
h: width 1152 start 1216 end 1344 total 1600 skew 0 clock 67.5KHz
v: height 864 start 865 end 868 total 900 clock 75.0Hz
1152x864 (0x46) 105.0MHz -HSync +VSync
h: width 1152 start 1224 end 1352 total 1552 skew 0 clock 67.6KHz
v: height 864 start 865 end 868 total 902 clock 75.0Hz
1152x864 (0x47) 96.8MHz -HSync +VSync
h: width 1152 start 1224 end 1344 total 1536 skew 0 clock 63.0KHz
v: height 864 start 865 end 868 total 900 clock 70.0Hz
1152x864 (0x48) 81.6MHz -HSync +VSync
h: width 1152 start 1216 end 1336 total 1520 skew 0 clock 53.7KHz
v: height 864 start 865 end 868 total 895 clock 60.0Hz
1024x768 (0x49) 94.5MHz +HSync +VSync
h: width 1024 start 1072 end 1168 total 1376 skew 0 clock 68.7KHz
v: height 768 start 769 end 772 total 808 clock 85.0Hz
1024x768 (0x4a) 78.8MHz +HSync +VSync
h: width 1024 start 1040 end 1136 total 1312 skew 0 clock 60.0KHz
v: height 768 start 769 end 772 total 800 clock 75.0Hz
1024x768 (0x4b) 75.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1328 skew 0 clock 56.5KHz
v: height 768 start 771 end 777 total 806 clock 70.1Hz
1024x768 (0x4c) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
832x624 (0x4d) 57.3MHz -HSync -VSync
h: width 832 start 864 end 928 total 1152 skew 0 clock 49.7KHz
v: height 624 start 625 end 628 total 667 clock 74.6Hz
800x600 (0x4e) 56.3MHz +HSync +VSync
h: width 800 start 832 end 896 total 1048 skew 0 clock 53.7KHz
v: height 600 start 601 end 604 total 631 clock 85.1Hz
800x600 (0x4f) 50.0MHz +HSync +VSync
h: width 800 start 856 end 976 total 1040 skew 0 clock 48.1KHz
v: height 600 start 637 end 643 total 666 clock 72.2Hz
800x600 (0x50) 49.5MHz +HSync +VSync
h: width 800 start 816 end 896 total 1056 skew 0 clock 46.9KHz
v: height 600 start 601 end 604 total 625 clock 75.0Hz
800x600 (0x51) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
800x600 (0x52) 36.0MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz
v: height 600 start 601 end 603 total 625 clock 56.2Hz
640x480 (0x53) 36.0MHz -HSync -VSync
h: width 640 start 696 end 752 total 832 skew 0 clock 43.3KHz
v: height 480 start 481 end 484 total 509 clock 85.0Hz
640x480 (0x54) 31.5MHz -HSync -VSync
h: width 640 start 664 end 704 total 832 skew 0 clock 37.9KHz
v: height 480 start 489 end 492 total 520 clock 72.8Hz
640x480 (0x55) 31.5MHz -HSync -VSync
h: width 640 start 656 end 720 total 840 skew 0 clock 37.5KHz
v: height 480 start 481 end 484 total 500 clock 75.0Hz
640x480 (0x56) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 59.9Hz
720x400 (0x57) 35.5MHz -HSync +VSync
h: width 720 start 756 end 828 total 936 skew 0 clock 37.9KHz
v: height 400 start 401 end 404 total 446 clock 85.0Hz
640x400 (0x58) 31.5MHz -HSync +VSync
h: width 640 start 672 end 736 total 832 skew 0 clock 37.9KHz
v: height 400 start 401 end 404 total 445 clock 85.1Hz
640x350 (0x59) 31.5MHz +HSync -VSync
h: width 640 start 672 end 736 total 832 skew 0 clock 37.9KHz
v: height 350 start 382 end 385 total 445 clock 85.1Hz
HDMI-1 connected 1360x768+0+0 (0x41) normal (normal left inverted right x axis y axis) 0mm x 0mm
Identifier: 0x3d
Timestamp: 1278799
Subpixel: unknown
Clones: HDMI-2
CRTC: 0
CRTCs: 0 1
1360x768 (0x41) 84.8MHz -HSync +VSync *current
h: width 1360 start 1432 end 1568 total 1776 skew 0 clock 47.7KHz
v: height 768 start 771 end 781 total 798 clock 59.8Hz
1152x864 (0x48) 81.6MHz -HSync +VSync
h: width 1152 start 1216 end 1336 total 1520 skew 0 clock 53.7KHz
v: height 864 start 865 end 868 total 895 clock 60.0Hz
1024x768 (0x4c) 65.0MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
800x600 (0x51) 40.0MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz
v: height 600 start 601 end 605 total 628 clock 60.3Hz
640x480 (0x56) 25.2MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 59.9Hz
HDMI-2 disconnected (normal left inverted right x axis y axis)
Identifier: 0x3e
Timestamp: 1278799
Subpixel: unknown
Clones: HDMI-1
CRTCs: 0 1
xorg.conf is here
Section "ServerFlags"
Option "AutoAddDevices" "false"
EndSection
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Touchpad" "SendCoreEvents"
Option "AIGLX" "true"
EndSection
Section "Files"
# RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "GLcore"
Load "xtrap"
Load "extmod"
Load "glx"
Load "dri"
# Load "record"
Load "dbe"
Load "freetype"
Load "synaptics"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "thinkpad60"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "InputDevice"
Identifier "Touchpad"
Driver "synaptics"
Option "SendCoreEvents" "true"
Option "VertEdgeScroll" "true"
Option "HorizEdgeScroll" "true"
Option "Device" "/dev/psaux" #/dev/input/mouse0
Option "Protocol" "auto-dev"
# Option "TouchpadOff" "1" #Uncomment if you just want to disable the touchpad and use only the trackpoint
# Option "HorizScrollDelta" "0" #Why is this in here by default. By Gods, it kill horizontal scrolling!
Option "RightEdge" "5500" #This is a little bigger than the default narrowing the scroll region
Option "BottomEdge" "4500" #This is a little bigger than the default narrowing the scroll region
Option "RTCornerButton" "0" #disable Right Top corner "button"
Option "RBCornerButton" "0" #disable Right Bottom corner "button"
Option "SHMConfig" "on" #this allows configuration of the touchpad using qsynaptics, synclient, or what have you.
EndSection
Section "Monitor"
DisplaySize 304.8 190.5 # 120 dpi @1440x900
Identifier "Monitor0"
Option "DPMS"
EndSection
Section "Device"
Option "NoDDC" "true" # [<bool>]
Identifier "Card0"
Driver "intel"
VendorName "Intel Corporation"
BoardName "Mobile Integrated Graphics Controller"
BusID "PCI:0:2:0"
Option "AccelMethod" "xaa"
Option "XAANoOffscreenPixmaps" "true"
Option "DRI" "true"
Option "FramebufferCompression" "false"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1440x900" "1280x800" "1024x768" "800x600"
Virtual 2960 1024
EndSubSection
EndSection
Section "DRI"
Group "video"
Mode 0666
EndSection
Section "Extensions"
Option "Composite" "Enable"
EndSection
and now i am using awesome wm. any ideas? Thank you!!

konni wrote:
how many monitors do you want to plugin? three? like damjan said, not sure if that works at all.
or are the hdmi outputs idle and you're just trying to plug in a second screen?
whats the exact problem? no output on that screen at all? or mirroring the internal one? in that case, try
xrandr --output VGA --right-of LVDS
(or left-of...)
can you plug that monitor in with hdmi? (adapter/etc) you might try that as well, maybe just the vga fails.
wow.. thank you konni... and thank damjan
i turned off HDMI-1, then I could get VGA work!
now i have dual screens, pretty cool.

How do I play a video in full-screen mode on one screen of a dual-screen Windows 7 system without blanking out the other screen?

How do I play a video in full-screen mode on one screen of a dual-screen Windows 7 system without blanking out the other screen? Not losing the other screen would be useful as I would like to, for example, monitor my emails whilst watching a video or to work on a project whilst watching an instructional video.
Note : Resizing a window to fill the screen is not acceptable as it still leaves unsightly borders.

bump

Dual Screens - can you do it on the Essential All in One?

I have a standard Essential all in one.
I thought it would be handy to run dual screens for something I am working on but cannot see a way to do this on the machine.
Is it possible?
Thanks
AMC

hi
Can you share what system are you using and what type of connection is has,
This is you computer model ex. Ideapad g500 y510P etc.. you can find it on your system stickers
Also share what TV/Display you're using.
This is the model name of your external Display, the external monitor you are using
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

How to darken only one screen in a dual screen setup ??

Hi All,
I have a dual screen set-up probably like many of you and sometimes I prefer to use LR only on 1 screen. That allows me to work on Photoshop or read my emails or whatever else I'd prefer to do on the other screen. My dilemma is when in Lightroom & I press the letter L to darken the screen around my image, for better viewing, it also darkens the other screen that I'm working with. Is there a way to prevent both screens from darkening?? Thanks Ron
PS: Apologies if this has been addressed previously as I could not locate it

Thank you digitaldog, I didn't think so either

Hi my iph4s wont turn on or off and seems to be zoomed into a particular part of the screen, loads normally when rebooted the phone. what is wrong with it? and how would i go abouts fixing it?thanks

hi my
iph4s wont turn on or off and seems to be zoomed into a particular part of the screen, loads normally when rebooted the phone. what is wrong with it? and how would i go abouts fixing it?
also recovery mode shows up as a red icon instead of a blue one, not jail broken or had any third party alterations
thanks

Reset the PRAM
Reinstall the operating system from the dvd (you will not loose your data)

After plugging my ipod into my mac mini, my screen split into 2 duplicate screens, one on top of the other. How do i make that go away?

after plugging my ipod into my mac mini, my screen split into 2 duplicate screens, one on top of the other. How do i make that go away?

I am not sure about everything, but there is something that may fix some of your problems. Go to System Preferences, and choose the "Universal Access" preference pane. In Universal Access, turn off VoiceOver, Zoom (seeing tab), Sticky Keys, Slow Keys (Keyboard tab), and Mouse Keys (Mouse tab). Make sure the "Enable access for assistive devices" checkbox, which is at the bottom of the preference pane. From there, look at other options and see if they are things you want turned off, or changed from how they are set. If you don't know what different options do, click on the help icon at the bottom left corner of the window. And if you are still baffled, ask here and someone will tell you what it does.
If you use any of the universal access options or think they could be useful, feel free to leave them on.
Also, go to the Keyboard and Mouse preference pane, choose the Keyboard Shortcuts tab, and make sure there are no strange keyboard shortcuts set that may interfere with the keys you are having issues with.
Did you install any new software before this started happening, and if so, how many days before it started happening?
Let us know if these tips get you anywhere.

Please tell me how to go back to a long text I wrote and then i must have accidentally swiped the screen one way or another. How do I go back to the screen so I don't have to re-write the whole text?

Please tell me how to go back to a long text I wrote and then i must have accidentally swiped the screen one way or another. How do I go back to the screen so I don't have to re-write the whole text?

Cloud takes over https://forums.adobe.com/thread/1584746 may help

The screen on my MacBook is zoomed in and won't go back to normal view

The screen on my MacBook has zoomed in. This happened while surfing on Facebook. Now it will not go whole screen view. I have tried shutting down and rebooting but that didn't work.

Lion
http://support.apple.com/kb/PH3988
Mountain Lion
http://support.apple.com/kb/PH11488
Hope this helps

What options do I have if I want to set up a dual screen?

I have a Thinkpad T400 with a ATI Radeon HD3470 card. I am running the latest Arch x86_64 with Fluxbox and the 9.4 Catalyst drivers.
What is the easiest solution to set up a dual screen? Is there a way to do this without editing xorg.conf? Not that editing xorg.conf really is a big problem, but I will be moving around a bit and finding the correct settings for each screen would take some work. And I would like to see how far the dual screen development has come on GNU/Linux.
The way I see it the best way would be to have two screens with separate resolutions. Since LCD screens do not handle resolutions other then the native very well. So just stretching the screen makes the slave screen run the same height as the parent screen. Or am I wrong? It is not a problem running stretched if the screens run at the native resolution.
So, xrandr just gives me stretching. And the need of editing xorg.conf.
What about Twinview(just for nVidia) and Xinerama?
Is there other solutions?
SOLUTIONS:
There is arandr and lxrandr, both frontends to xrandr. Requires minimal xorg.conf editing. Only add a virtual line in the screen section. The virtual size does not have to be accurate, it only have to be bigger then the screens together. In my case, I have a 1440x900 primary screen and at most a 1280x1024 secondary screen. So my virtual size would be minimum 2720x1024. This is with the screens side by side. If the screens is one above the other it would be 1440x1924.
The exact size of the monitor is handled by xrandr(arandr or lxrandr). So, there will be no dead zone in the width(side by side solution), if the real height is different on the screen there will be a dead zone in height.
Using arandr or lxrandr means that you manually have to set this up each time the computer is restarted. To automate this, you can use xrandr. First do a
# xrandr
Screen 0: minimum 320 x 200, current 2464 x 900, maximum 2720 x 1024
LCD connected 1440x900+0+0 (normal left inverted right x axis y axis) 304mm x 190mm
1440x900 50.0*+ 60.2
1152x864 60.0 50.0
1280x768 59.9 50.0
1280x720 60.0 50.0
1024x768 60.0 50.0
800x600 60.3 50.0
720x480 60.0 50.0
640x480 60.0 50.0
640x400 59.9 50.0
512x384 60.0 50.0
400x300 60.7 50.0
320x240 60.0 49.9
320x200 60.1 50.0
DFP1 disconnected (normal left inverted right x axis y axis)
CRT1 connected 1024x768+1440+0 (normal left inverted right x axis y axis) 304mm x 228mm
1024x768 60.0*+ 75.0 70.1 60.0*
800x600 72.2 75.0 70.0 60.3 56.2
720x480 60.0
640x480 75.0 72.8 75.0 60.0
640x400 75.1 59.9
512x384 60.0 74.9
400x300 75.0 60.7
320x240 75.6 60.0
320x200 75.5 60.1
to find out where the screens are connected. Mine are LCD and CRT1. Then test with
# xrandr --output CRT1 --right-of LCD
to see if you get a stretched desktop. If this works, just add the last line to your .xinitrc
This solution gives you stretching.
My complete xorg.conf
# Copyright 2004 The X.Org Foundation
Section "ServerLayout"
Identifier "Laptop"
Screen 0 "Default" 0 0
EndSection
Section "ServerFlags"
Option "AutoAddDevices" "True"
EndSection
Section "Monitor"
Identifier "LCD"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "radeon_hd"
Driver "fglrx"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Default"
Device "radeon_hd"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1440x900" "1024x768"
Virtual 2720 1024
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
Last edited by orjanp (2009-05-01 09:33:55)

I have an ATI Mobility x1600 on my laptop,and I use a separate CRT monitor as second output (well primary until I fix my backlight)
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
Screen 1 "Screen1" RightOf "Screen0"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "USB Mouse" "CorePointer"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "true"
Option "AutoAddDevices" "False"
Option "DontZap" "False"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc:unscaled"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/75dpi"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/100dpi"
FontPath "/usr/share/fonts/PEX"
FontPath "/usr/share/fonts/cyrillic"
FontPath "/usr/share/fonts/local"
FontPath "/usr/share/fonts/Type1"
FontPath "/usr/share/fonts/ttf/western"
FontPath "/usr/share/fonts/ttf/decoratives"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/truetype/openoffice"
FontPath "/usr/share/fonts/truetype/ttf-bitstream-vera"
FontPath "/usr/share/fonts/latex-ttf-fonts"
FontPath "/usr/share/fonts/defoma/CID"
FontPath "/usr/share/fonts/defoma/TrueType"
EndSection
Section "Module"
Load "ddc"
Load "drm"
Load "dbe"
Load "dri"
Load "extmod"
Load "glx"
Load "bitmap"
Load "freetype"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
Option "XkbVariant" ""
EndSection
Section "InputDevice"
Identifier "USB Mouse"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "SendCoreEvents" "true"
Option "Protocol" "IMPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
Option "DPMS" "No"
EndSection
Section "Monitor"
Identifier "Monitor1"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
Option "DPMS" "No"
ModeLine "1024x768" 44.9 1024 1032 1208 1264 768 768 776 817 +hsync +vsync Interlace
ModeLine "1024x768" 65.0 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
ModeLine "1024x768" 75.0 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
ModeLine "1024x768" 78.8 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
ModeLine "1024x768" 94.5 1024 1072 1168 1376 768 769 772 808 +hsync +vsync
ModeLine "1280x1024" 108.0 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
ModeLine "1280x1024" 135.0 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
ModeLine "1280x1024" 157.5 1280 1344 1504 1728 1024 1025 1028 1072 +hsync +vsync
ModeLine "1024x768" 113.31 1024 1096 1208 1392 768 769 772 814 -HSync +Vsync
ModeLine "1280x1024" 190.96 1280 1376 1520 1760 1024 1025 1028 1085 -HSync +Vsync
EndSection
Section "Device"
Identifier "Card0"
Driver "ati"
VendorName "ATI Technologies Inc"
BoardName "M56P [Radeon Mobility X1600]"
BusID "PCI:1:0:0"
Option "AGPMode" "4"
Option "ColorTiling" "on"
Option "AccelMethod" "EXA"
Option "AGPFastWrite" "yes"
Option "DRI" "on"
Screen 0
Option "DDCMode" "True"
Option "MonitorLayout" "LVDS,CRT"
EndSection
Section "Device"
Identifier "Card1"
Driver "ati"
VendorName "ATI Technologies Inc"
BoardName "M56P [Radeon Mobility X1600]"
BusID "PCI:1:0:0"
Option "AGPMode" "4"
Option "ColorTiling" "on"
Option "AccelMethod" "EXA"
Option "AGPFastWrite" "yes"
Option "DRI" "on"
Screen 1
Option "DDCMode" "True"
Option "MonitorLayout" "LVDS,CRT"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1280x800" "1024x768"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen1"
Device "Card1"
Monitor "Monitor1"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1024x768"
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
Section "Extensions"
Option "Composite" "false"
EndSection
This works, and I get separate resolutions on the monitors. I tried using radeonhd but then the resolution on teh second monitor goes to some crappy values(which I figure are calculated proportionally to the 1280x800 one).

Dual screen - at a loss

Hello all. Is there anything special at all to dual-screening mega 180?
I Installed everything, the CD. Then I powered it off, plugged my second screen in the secondary VGA plug.
While XP was booting, both screens showed - perfectly - the booting screens.
Then when windows was fully loaded, the secondary screen fried. It is NOT a screen failure, as when I plug the primary screen in the secondary VGA plug, it won't work either, though it won't fry. I can test that because the secondary screen will still show windows, though badly distorted so I just have to exchange their positions to test.
So is that a Mega 180 RMA? Or is it something I forgot to do? Does anyone know how to get my screen back? Symptoms are as follow:
the image is WAY too large (inches more than the screen left, and right, with H-size set to minimum). It seems the problem stems from the H frequency:
the correct screen shows H-50Hz V-60Hz the incorrect one shows H-40Hz V-60Hz
Any programs can set those values?
Anyways thanks and good day to you all!

As an update, I tried switching the main display to the MBP. Nothing changed.
However, I changed the rotation to 90 degrees and everything is back to Normal! Aside from the fact that I'm looking a 24" screen in the vertical position.

Dual screen GDM problem

I have a rather big problem with my dual screen setup. The left screen is 1920x1080 and the right one 1360x768.
This is my /etc/X11/xorg.conf:
Section "Monitor"
Identifier "DVI-0"
Option "Primary" "true"
Option "Position" "0 0"
Option "PreferredMode" "1920x1080"
EndSection
Section "Monitor"
Identifier "DVI-1"
Option "Position" "1920 180"
Option "PreferredMode" "1360x768"
EndSection
I set it up as described here. However, GDM doesn't behave as normal, but gets stuck with a slightly dimmed default GDM background (the one with the blue stripes) on the first screen and a crazily flashing second screen. I never even get to the login prompt.
If I plug the second screen out before the computer boots, GDM starts normally. I can then plug it back in as soon as the GNOME Shell panel has appeared. If I do this before the panel is visible, I get two screens full of graphics errors (a mess of blue/magenta/white squares).
As soon as the second screen is plugged back in, I can immediately use it and drag windows back and forth, however, the "Position" setting in xorg.conf is ignored, i.e. the height is shifted. I can solve this by entering this in the terminal:
xrandr --output DVI-0 --mode 1920x1080 --pos 0x0 --output DVI-1 --mode 1360x768 --pos 1920x180
I hope someone can help me with this. I just want to be able to log in and use the second screen straight away. By the way, if I log out, GDM doesn't seem not have any problem with the second screen: I can log back in normally.
Thanks in advance!

Archimaredes wrote:I don't have much experience with this, so forgive me if I'm wrong, but should that not be 1080, instead of 180?
Thank you, but "180" actually means that the upper border of the 2nd display starts 180 pixels below that of the 1st one. The number may be a bit misleading, but it is how my displays are physically set up.
olive wrote:If gdm cannot behave properly, you can simply disable the external monitor in xorg.conf
This is a fabulous idea, I hadn't even thought about this! Launching the xrandr command at the start of the GNOME session is really easy with gnome-session-properties.
I tried disabling the 2nd display, but it just ignores the line and starts with GDM flashing like usual. This is my xorg.conf:
Section "Monitor"
Identifier "DVI-0"
Option "Primary" "true"
Option "Position" "0 0"
Option "PreferredMode" "1920x1080"
EndSection
Section "Monitor"
Identifier "DVI-1"
Option "Position" "1920 180"
Option "PreferredMode" "1360x768"
Option "Disable" "true"
EndSection
If I could get this to work, this would be a wonderful workaround.

New mac user, IMac with thunderbolt dual screen no longer works

Hi, I have just started using a mac for work and was loving my new dual screen setup. it was functional for a day and now the second screen is black and saying I should check the signal cable. I have
     Tried other DVI cables that go from thunderbolt to screen
     tried 3 screens, one of them from a different brand
     I have updated firmware
     and restarted / shutdown/ disconnected device then reconnect about 10 times
     and pressed detect displays about 20 times (it seems to detect the screen, its just not sending it anything?)
     before the screen stopped I had to do a restart for the latest Itunes and mac updates
but to no response. please help my productivity is really reduced

Take a look at these links,
http://support.apple.com/kb/HT4744
http://support.apple.com/kb/TS3775

Using Keynote with Podcast Capture and Dual Screens

Hi everyone,
We are trying to use a dual screen setup to record some Keynote presentations using Podcast Capture (i.e Dual mode, with the Keynote presentation in one screen and the presenter in the other).
The problem we are having is that when in full screen mode, Keynote takes control of both displays, thus stopping the Podcast application from being displayed. Even if we switch off the Presenter Display on the second screen, the second screen turns black.
I know we can start and stop recording with hotkeys, but we would prefer to be able to see the Capture app in one window with the presentation full screen in the other.
Perhaps this is just an oversight on Apple's part, but I'm finding it hard to believe its not possible. If anyone else has a workaround then please share.
Thanks.

Other applications are not visible when Keynote is playing back. Keynote takes over control of the graphics system when playing back presentations to enable Keynote to display properly.
When I play back Keynote and I want to look at a second application, I use a second Mac.

MSI gtx 570 twin frozr III - Dual Screen Windowed mode issues

Ok, so... I was running a solo monitor 1440x900 resolution, i recently purchased a brand new asus 24 inch 1900x1080 monitor. Basically what is happening is when i play WoW or Battlefield 3 in windowed mode on the 1080p monitor the colors are not perfect. When i go full-screen on the new monitor no issues, but that is not what i want to have to live with. When i say the colors are not perfect what i mean is, for example when i look @ the sky instead of being a smooth transition or blend from one shade of the sky to the next it is bars or stripes of each shade as if i am looking at the sky in 8 bit color instead of 32 bit color. Another thing to note is that when i login to windows 7 the blue screen where i input the password has the same effect. The 1440x900 monitor is running everything just fine. the only issue is with the 1080p monitor.
I am using DVI cabling for both, and have swapped them around to see if that was the issue, and sadly it is not. I am running the updated gpu driver, which i uninstalled and re-downloaded and installed again tonight.
When i use the HDMI cable, that fixes the issue but i need the HDMI for my 42 inch tv.
Also in windows, just to cover my bases with this post, i have the native resolutions properly configured, as well as in the game for the given monitor it is being played on.
Anyone know of a fix for this?
i7 2600k
asus PBZ68-v Pro/Gen3
Msi gtx 570
Samsung syncmaster 953bw (1440x900)
Asus VS248 (1900x1080)
I am more than happy to re-explain anything that may not be as descriptive or clear to you just let me know!
EDIT!
When i run the 24 inch 1080p new monitor as my only monitor on the system, everything runs perfectly...
Edit #2
Ok so i have pin pointed a possible cause
This msi gtx 570 struggles with operating multiple displays with different resolutions, while dual screening with my 1080p television and the 1080p display, everything runs as expected. Having to also render a 1440x900 display is probably the reason i am having the graphic issues. Is there any type of utility, setting, or other fix to this type issue? also this gpu is certainly less than 2 weeks since i purchased i could get a different card to remedy this... any suggestion? if you suggest a different card can you say so with certainty that it will work properly under the condition in which 2 resolutions will be required?

Ok, the problem is fixed and Svet i skipped a step or two. I installed the new driver with the clean install to save time for an initial attempt. What is interesting is that with the Geforce driver, only one 1920x1080 resolution was available
The msi driver gave me 2 options, 1920x1080 and 1920x1080 (native). The latter resolution fixed the issue for whatever reason.
The solution to this problem is so easy, when i purchased battlefield 3 it prompted me to download the geforce.com driver and i did not think anything of it at the time, lesson learned.

Dual screen, one normal res, one zoomed in

Similar Messages

Maybe you are looking for