E1000 router

I had a WRT54g router which I set up a point to point wireless connection to a wireless printer. I did not have a
network set up and it worked fine.
With the new E1000, do I have to set up a network for it to work with the wireless printer?
Thanks in advance.

I think you have to install the Linksys E1000 router on your computer so that you have the network in your home .
If you are using the router only in Local network make sure you have the correct SSID and Password to connect the network on your wireless printer .
Connect the Modem to the Internet port on your Linksys E1000 router .
Connect the computer with the Ethernet cable to the Ethernet port on your router .
Install the Cisco Connect Software on your computer .
After the successful installation , Go to the Router settings and you will find the Router name (SSID) and password .
Connect your wireless printer to that SSID using the password.
Who is your Internet service provider ?

Similar Messages

  • Airport Express and Cisco E1000 router?

      Okay so right now i am using my airport express as my primary router can i use it to extend my cisco E1000 router if i plug back my old Cisco E1000 router if i can how do i do it? Please help.

    You can effectively extend the Cisco's wireless network by creating a roaming network with both routers. Note that this would require that both routers be interconnected by Ethernet. Since the Express will perform a new role, be sure to perform a "factory default" reset on it so that it will be in its "out-of-the-box" configuration.

  • Problem finding Linksys E1000 router

    Hi all.
    I just purchased an E1000 router for my brothers computer. He has Comcast as his ISP so i was trying to set up the router and clone his IP address as per other instructions i have read online when dealing with Comcast. However i can not gain access to his router via the 192.168.1.1 address or the CD setup. They both say router not found.
    I know the cable is good because i take it directly out of the cable modem and plug it into the "internet" port of the router. I've also tried it in port 1 of the lan side and still can not get acceess. I havent tried the router on another computer yet but since his is the pc i want it to work with, i have to get it to work on that one. I've also tried restarting the pc after the cable was connected.
    Any help is appreciated.

    Press and hold the reset button on the router for 30 seconds. Release the reset button and wait for 30 seconds. Power cycle the router.
    Connect the modem to the Internet port and computer to Ethernet port 1 on the router. Open the setup page of the router.  Clone the MAC address of the main computer and save the settings. Unplug the power cable to the router and modem. First plug in the power to the modem and wait for 1 minute. Plug in the power cable to the router and wait for 1 minuter. Try to access the Internet through the router.

  • Cannot get Cisco Connect to install or set up E1000 router

    1. We have been using an E1000 router connected to our main Dell desktop (running XP SP3) to handle a small home network that includes wife's laptop which has card and kids' desktop with USB wireless adapter.
    2. We purchased a new main desktop computer, ZT Systems running Windows 7. I am attempting to install Cisco Connect on this computer and set up the router. I reset it to factory specifications because I figured I'd have to start from step 1.
    3. I cannot find the original setup CD that came with the router and I have no clue whatsoever what my password is.
    4. So, I downloaded CiscoConnect.E1000.1.3.11069.2, the appropriate software to my desktop, and have been trying to install the software and configure the router, without any success whatsoever. When I plug it in, it asks me to connect the router which I do. It then will get to 25 percent of setup and stop, saying it couldn't be configured. At the same time, I have no Internet access, keeps telling me it's looking for networks when I actually am trying to set up a network.
    5. I've tried the steps for configuring without the software, Windows still searches for a network and tells me it can't find one and I have no Internet access.
    6. Can anyone tell me what's going on here, what I'm doing wrong, anything I'm missing? Do I need to just buy another router or what? Thanks in advance for any help.

    Does your desktop have wireless? If so, switch it off and retry the installation. Make sure to reset the E1000 by holding the reset button for about 10 seconds.

  • Why can't I access the control panel of my E1000 router?

    http://192.168.1.1/ cannot be displayed when I click on it, as if the page does not exist. http://my.E1000 doesn't work either.
    My router frequently has connection issues as well when laptop users are complaining that they are "connected but have limited connectivity". In reality they have no connectivity. They have no internet access on their browsers or games. Resetting it seems to be the only thing that ever fixes this and now, despite my network supposedly being called "Neil," it's calling its self "Neil 2" and has no password. I can't change it back because I cannot get into my router's settings either!
    So yea. In a few words, it's all kind of bork. Does anyone know what is wrong with it?
    Solved!
    Go to Solution.

    What is the ip address you are getting on the computer which is connected to the router....?
    Check the ip address.If you are getting the correct ip address(192.168.1.1) then,reset the browser settings and try again to open the setup page.If that also does not work then,reset the router for 45-50 seconds,power cycle the router and check.

  • Connecting EZX55W switch to E1000 router

    I just purchased a E1000 wireless router to replace our BEFSR41 router that died. The old router had a EZX55W switch connected to it  (4 computers, xbox, blu-ray player) and I would like to do the same with the E1000. There is no uplink port on the E1000. Any knowledge out there on the proper way to accomplish this or is it not possible?
    Thanks in advance for any help.
    Rob

    It's Good to know that you were able to resolve your issue your own...Enjoy .

  • E1000 Router Wireless signal will disappear after some time

    Hi,
    I have set up the E1000 this week, i found that the wireless signal would disappear after some time if the wireless connection is not in use.
    For example, on my iphone
    1. I search for the wireless signal and successfully got the IP
    2. after using for some time, i put the iphone aside
    3. when i want to use the wireless again, the iphone is not yet connected to the wireless 
    4. i would then need to search for the wireless signal and connect again.
    This causes problems because i am using some VPN connection at my laptop and it would disconnect it.
    Is there any config that would keep the wireless signal ?
    Thanks!

    Try changing the wireless channel on the router.
    Also try to change some advanced wireless settings on the router. Click on Wireless tab and go to Advanced wireless settings. Change the Beacon interval to 75, RTS threshold to 2307 and fragmentation threshold to 2306. Save the settings.
    See if that helps you.

  • Error in trying to connect E1000 router to Dell Desktop via ethernet cable.

    Connected my Dell laptop to the E1000 using the enclosed disk, easy install and no problems with wireless connection.  Created a USB via the install disk to connect the Dell desktop (XP pro SP3). When running installing received error pop up "installation not compete" contact Linksys support for assistance. Disabled all internet connections and tried a manual installation but failed.  Any suggestions? or should I just purchase a wireless USB addapter?  Thanks for  your assistance.

    Just connect the computer with an ethernet cable to the router and that's it. No installation necessary.

  • I'm having trouble using a Linksys E1000 Router

    I purchased a Mac in November. Love it so far with a few minor exceptions.
    I changed routers because I was having speed/connection issues.
    Switched from a Netgear to a Cisco Linksys E1000 which I had purchased a couple of years ago for a PC that i replaced with the mac. The software with the Linksys says it cant be used with the version of the new mac Mac OS X 10.7.2.
    Any suggestions?
    Thanks,

    I gave up on Linksys some time ago. I had a lot of trouble with their routers, and a very frustrating useless experience trying to get tech support help. I found one a few days ago while doing some spring cleaning and threw it out. Not worth the trouble.
    I got a refurbished airport express and it works great.

  • Cisco Connect can't find my E1000 router

    My router is working find but Cisco Connect can't find it. I'm locked out of making changes.

    I'm trying to find my username and password via Cisco connect. 192.168.1.1 requires my username and password to continue. I appear to be dead unless I do a H/W router reset and risk shutting down my network...I'm worried it won't come back alive!
    Gary

  • Linksys e1000 router blinking all lights steadily not functioning

    Somehow in the process of researcing how to add my new laptop to the router, the  router quit working and is now just  blinking the blue panel lights.
    I was attempting to download Cisco Connect to my flash drive and instead it  began to execute and I aborted that in about 10 seconds.
    Wondering if just that messed up the original setup which was working fine..
    Thanks,
    jim

    Well go ahead and try resetting the router by pressing and holding the reset button in back for 30 seconds. 

  • Does airport card (origional) support linksys e1000 router?

    I just got and airport card for my old mac, and want to use it with my network. but it won't work with my network. Is there any fix for this? software?

    There is a Safari 2.0 download, however it won't run on OS 10.2.
    Suggest you look at some of the browsers on this site http://mac.oldapps.com/
     Cheers, Tom

  • Cisco Linksys E1000 Connection to Verizon Router

    OK here is the situation.  I spent two with a verizon tech on the following issue.
    I have new PC, windows 7, that I have connected via wireless Trendnet 150Mbps Mini Wireless N USB Adapater. The spped is less than 5Mbps download and upload.  My verizon plan is 25Mbps.  In the end it was determine that the verizon technology is g format and the adapter is n technology. The computer directly hard wired to the verizon router gets 30Mbps speed.
    Bought a Cisco Linksys E1000 N technology router to connect to the Verizon router.
    Connected to router and could not get any internet even though the signal strength was extremely good.
    Got any suggestion on how to get this to work.
    I am dying with this problem,

    When connecting the E1000 router to your fios one, i would use one of the 4 LAN ports and not the WAN port to make the Ethernet connection between the two. Then go into the router web page of the E1000 (192.168.1.X) and make sure that the DHCP server is disabled.
    Now for your speed problem. Even with wireless G you should still be fine as it can tranfer much faster than 5Mbps. The problem could be that the Trendnet usb adapter has a pretty tiny radio and your connection slows way down as you move away from the the wifi source.

  • Cannot connect to router E1000

    Hello,
    I own a E1000 router that I use with several wireless machines. I have no problem connecting to the internet.
    Unfortunately, I cannot connect to the configuration of the router by typing https://192.168.1.1/ nor http://192.168.1.1/ in a browser, be it wirelessly or wiredly. For example, Firefox displays "Connection has been reinitialized". Furthermore, when I launch Cisco Connect, it only shows the error "Unable to connect to router".
    I tried to switch my router off and on, but that doesn't help. Totally resetting the router solves the problem, but not definitely.
    Is there a solution that does not require resetting my router?
    Thank you very much.

    (I don't see anymore how to edit my initial post.)
    The message displayed by Firefox is “The connection was reset” and not what I had translated into “Connection has been reinitialized”.
    As far as the OSs are concerned, the machines that should be able to access my router are running Ubuntu, Android, Windows and an embed version of Linux. I tried with different webbrowsers, including Firefox and the Android Browser.
    Please tell me if I should add any additional information.
    I did a lot of search on the web and some say that similar problems come from the option of HTTPS that is selected for accessing the administration page. Is this correct? Should I abandon the idea of wanting a configuration with HTTPS?

  • How to get rid of the guest network on E1000

    Is there a way to get rid of the guest network on a E1000 or is it part of the setup.

    Hello Burns1214 ,
    I posted an answer here http://homecommunity.cisco.com/t5/Wireless-Routers/Enable-quot-Guest-Access-quot-on-E1000-Router/m-p.... You can only disable it thru Cisco Connect software.

Maybe you are looking for