Edge 2013 does not discover all Exchange servers in the org

We have the following co-existence setup:
Edge 2013 sitting on the DMZ.
1 CAS 2013
1 MBX 2013
1 CAS/HUB 2010
1 MBX 2010
After creating a new edge subscription on the edge server and successfully completing it on the 2013 mbx server, when I run get-exchangeserver on the edgeserver I get only the 2010 CAS and the 2013 MBX. 2010 MBX and 2013 CAS are missing.
All mailflow is working fine, yet if I shutdown the 2010 CAS, incoming mail flow stops, because for the edge server the 2010 CAS is the nexthopdomain, it doesn't find it and gives a 4.4.1 error in the SMTP receive protocol logs.
I have tried re-creating the subscription several times, I tried forcefullsync, it syncs fine yet it does not discover all the servers.
The firewall on the edge is disabled and in the internal servers as well, just to be sure that there is no communication error.
When the edge server receives an email from the internet it sends it to the 2010 CAS/HUB server and then to the 2013 MBX server.
Also the documentation from technet states the following for Edge and messages arriving from external senders.
Mailbox server and Client Access server installed on different computers   In this configuration, the Client Access server is bypassed for inbound mail flow.
Mail flows from the Transport service on the Edge Transport server to the Transport service on the Mailbox server.
So in my config, the CAS should be bypassed, but yet that's not happening. The "proxy to a CAS server" option on the connectors is not enabled.
I believe all the above would be resolved, If I could make the Edge server discover all of the servers in the org.
Ideas?

Hi Dimitris,
Base on my knowledge, I think this is a normal behavior on Edge server. Since the computer that has the Edge Transport server role installed doesn't have access to Active Directory.
We will create an Edge Subscription from mailbox server(Exchange 2013) or hub server(Exchange 2010). So the Edge server will only connect to these servers with transport role.
According to the Edge Subscriptions document, it said:
“The Edge Subscription process provisions the credentials used to establish a secure LDAP connection between Exchange 2013 Mailbox servers and a subscribed
Edge Transport server.”
Edge Subscriptions
https://technet.microsoft.com/en-us/library/aa997438(v=exchg.150).aspx
Best regards,
Niko Cheng
TechNet Community Support

Similar Messages

  • Visual Studio 2013 does not rebuild all code resulting in old code deployed through wsp

    I recently converted my SharePoint 2010 project from Visual Studio 2010 to Visual Studio 2013. I have the Premium version with Update 1.
    I quickly noticed that 2013 has bugs. For instance I could get a build error out of nowhere while developing, stating that a method recently added to Class
    A used by Class B, does not exist. The only way to resolve is to restart Visual Studio. Sometimes a rebuild would do the trick too.
    I can live with such quirks as a developer. The big problem is that it does not build the latest version if you are using the "Publish to File System"
    to get a wsp for deployment on another server.
    I've had problems with incomplete builds since my first deploy with wsp built by Visual Studio 2013, but I was not able to pinpoint it with certainty until
    last night.
    I have two classes used by a timer job. In a new version they back up some files after using them. After upgrading with the new wsp, I restarted the timer
    job service on all servers and ran the job, but the files did not back up. So I went and added a log statement to the backup code of one class and did another clean/rebuild/publish to file system from Visual Studio. I upgraded using the new wsp and then restarted
    the timer job service on all servers. When I ran the timer job service, the class where I added the log statement backed up the files it should. The other class still did not. So I added a log statement to this class as well and deployed that. Then this class
    started to backup files too.
    So I conclude that Visual Studio 2013 is failing at its core in a very dangerous way leaving assemblies built in an unknown, incomplete limbo state.
    I am downgrading all projects to Visual Studio 2012.
    This post is mainly to share my experience with the community, but if someone at Microsoft wants to investigate the issue, here is a suggestion on how to reproduce:
    Have Visual Studio in Debug build.
    Make a change to a class in a SharePoint project.
    Deploy the change to a local SharePoint installation.
    Change to Release build.
    Use Publish to file system to get a wsp. Open this wsp, copy the assembly, reflect and investigate to see that code change is actually there.
    Tore Olav Kristiansen

    Hi,
    As this is a Visual Studio question, I suggest you post it to Visual Studio Forum, you will get more help and confirm answers from there.
    http://social.msdn.microsoft.com/Forums/en-US/home?category=visualstudio
    Thanks,
    Dennis Guo
    TechNet Community Support
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
    [email protected]
    Dennis Guo
    TechNet Community Support

  • Wlst command listWebServices() does not show all web services in the domain

    Hi, I am trying to use wlst command listWebServices() to display all web services of a domain. It seems that it only displays the web services of enterprice applications (ear apps), but it does not show the web services of web applications (war apps). If I pass ear appliication name and one of its web module to listWebServices, it will show the web services that belong to the web module of this application. However if I pass war application name and its web module name to listWebServices, it will return "Unable to find the SOA Composite or Service. Oracle UCM Native Web Services", although I can see from wls admin console or em that this web application does have a couple of web services.
    I also tried to call listWebServicePolicies, again it returned "Unable to find any Web Services with the specified Application".
    My purpose of doing above is to use wlst to detach/attach web service policies for some web services. Since I cannot find the web services, I off course cannot detach/attach policies.
    Does anyone have any clue how to find web services using wlst command that belong to a war application, and then detach/attach policies ? Any help will be greatly appreciated.
    Thanks,
    Jian Huang
    From Oracle fusion HCM

    As of UCM version 11.1.1.6, Oracle UCM Web Services are managed from Enterprise Manager in Fusion Middleware Control, not Weblogic Admin Console!
    A document at Oracle support explains this in more detail: https://support.oracle.com/epmos/faces/ui/km/DocumentDisplay.jspx?id=1456506.1 :
    Setting up GenericSoapService in WLS to use WS-Security:
    Go to FMW Enterprise Manager. http://wlshost:7001/em
    In the tree, navigate to Weblogic Domain -> <Domain Name> -> and click on UCM_server1. (If the managed server for WCC is named something other than UCM_server1, click on that name.)
    From the UCM_server1 drop down menu, select "Web Services".
    On the "Oracle Infrastructure Web Services" tab, click the GenericSoapPort link.
    Once there you can set the policies you want and restart the server!
    Regards,
    Göran
    Edited by: Göran Paues on 2012-aug-20 10:02

  • IPhoto does not add all new photos to the photostream???

    iPhoto is not adding all new photos from one group, recently imported, to the photostream. Why? The photostream has space. The photos were all taken the same day, but only a small number of them from one import show up. Any idea why?

    I have already got my refund for the cable! I tried a friends cable and everything works!

  • Search for mail in Outlook 2013 does not have all emails in result.

    Hi, we have a user that tries to search for a sertain mail in her mailbox, and when she searches, a few mail comes up, but the one she knows is there, and that fits the search pattern, is not listed in the results.
    We have tried to reindex the database the user was on, we have moved her to another database, and none of these have given us the result we want.
    We have also removed the checkmark in "Search" in Outlook for "Improve search speed by limiting the number of results shown".
    If she does the same search in OWA or Outlook 2010, the result is as expected, but in Outlook 2013, it is not.
    Has anyone experienced this, and if so, what could be done to solve it?
    Google(Bing) produces very little results that are relevant to this for me.
    Hope someone here has an answer :)
    Regards
    Tore Melberg

    Hi,
    I'm marking the reply as answer as there has been no update for a couple of days.
    If you come back to find it doesn't work for you, please reply to us and unmark the answer.
    Best Regards,
    Steve Fan
    Forum Support
    Come back and mark the replies as answers if they help and unmark them if they provide no help.
    If you have any feedback on our support, please click
    here

  • Self Service Portal Intermittently does not show all my requests in the "My Requests" section

    I have some customers reporting that they are missing requests in the "My Requests" section of the self service portal intermittently, i.e when they log in one time they will only see a couple of work-items, other times they will see all of them. 
    Has any one seen this?  Any suggestions on how to troubleshoot?  I have taken a look at the silverlight logs and there seems to be no logged errors.

    It sounds like "the bug".
    Next time it happens, try this:
    -- Step 1 Clean the execution plan cache
    dbcc freeproccache
    -- Step 2 Reproduce the problem and run the following query
    SELECT * FROM sys.dm_exec_query_stats AS qs
    CROSS APPLY sys.dm_exec_sql_text(sql_handle)
    CROSS APPLY sys.dm_exec_text_query_plan(qs.plan_handle, qs.statement_start_offset, qs.statement_end_offset) AS qp
    WHERE text LIKE N'%Composite_Select_Path_180f5706-3d05-4bbc-ca2d-c33624fdb3c8%';
    GO
    -- Step 3 Modify SQL Query and execute it
    EXECUTE sp_create_plan_guide_from_handle
        @name =  N'Guide1',
        @plan_handle = 0x06000500EEBEEF2940016668010000000000000000000000,
    -- please replace this value with the plan handle discovered in step 2
        @statement_start_offset = 966;
    -- please replace this value with the start_offset discovered in step 2
    -- Step 4 To see current plan guides
    select * from sys.plan_guides
                    -- Step 5 (only if Rollback is needed)
    EXEC sp_control_plan_guide N'DROP', N'Guide1';
    GO
    Edit: this is done against the ServiceManager db

  • Linn kinsky does not show all music folders - only the one which was created with wma but not the flac files wich where created with winamp

    Who can give me advice - do i have to change settings in i pod touch or in the folders from my computer ?

    Linn Kinsky is a app which helps you to control your LINN  audio - streamer
    This Kinsky programm is available for computers and apple products as well.  So the Kinsky programm runs perfectly on my windos computer and after reading articles i decided to purchase a more handy ipod touch to control my audio-streamer instead of using the notebook.
    unfortunately wma files are shown only. Meanwhile i ripped some cds as AIFF because I expected the problem here but nothing has changed.
    Anyway thanks for your answer Matthias

  • Itunes does not download all purchased songs from the Itunes Store

    A few weeks ago, I purchased the latest CD of Lionel Richie from the Itunes Store, but only 4 songs were downloaded. Now every time I try to download the rest CD by either checking for purchases in the Itunes menu or trying to buy the CD again, it tells me the Itunes Store is temporarily unavailable...
    Anyone knows how to solve this??

    I had a similar problem with a Jimmy Buffett album,I sent the iTunes store an e-mail described the problem including the album title and receipt number and within 24 hours they responded and had done a "reset" and problem solved.
    Give it a try

  • Safari 3.2.1 for XP does not display all graphics properly

    Safari 3.2.1 for XP does not display all graphics properly, including the Apple Support Website http://www.apple.com/support/.

    Maybe this will also help:
    If your Safari won't open, one or more of the following procedures should fix it:
    1. Go to Home/Library/Safari/ folder and remove the following two files:
    • history.plist
    • lastsession.plist
    (Safari may not load properly If these two files are corrupted.)
    2. Go to Home/Library/Caches/Metadata/Safari/ and remove the contents of that folder.
    (These are just webhistory files and are not required for Safari to run. However, similar to preference files, problems can arise if they have become corrupt.)
    3. Locate the cookies.plist file that's located in the Home/Library/Cookies/ folder and remove it.
    (Again, faults in stored cookies may interfere with Safari's launch.)
    4. Check whether any of your third-party internet plug-ins may be interfering with the launch of Safari by carefully moving them to the desktop (do NOT delete them at this stage). You can find these in two places:
    Home/Library/Internet Plug-Ins/ folder, and Global plug-ins are located in the Macintosh HD/Library/Internet Plug-ins/ folder.
    Restart Safari and place them back in the correct folders, one at a time, closing and re-opening Safari each time. If you discover that one of them was causing the problem with launching Safari, trash it and download and install a fresh copy.

  • Using term set as refiner in content search web part does not show all used terms

    When you create a terms set (12 terms with +/- 10-20 child terms) , attach it to a site column and allow multiple values to be selected the search service does not find all used values in the REFINERS tab of the content search web part.
    Example:
    Field ‘Tags’ is the term set which can be refined. We want to do this in the REFINERS tab of the content search web part.
    Tags is containing following fields:
    •Course document
    •Poster
    •ALS
    •Before
    •During
    •CPR/AED I
    In all libraries we used +/- 15 different tags already.
    Example of a tag field in the library:   "Poster;ALS;Belgium"
    The problem is we can’t see all of the used tags in the refiners tab when you open it for the first time.  (You can see Belgium or Cyprus is not in the list of tags.)
    When you select one tag and add it as a refiner, the others eventually do show up. But never all of them together.   It’s like he is only showing the most used (and maybe first selected?) tags first. I also think he might be having some trouble
    with multi value selections in the tag field.
     Does anyone else have the same issue as we do? And is there a solution already?

    Hi Sasha,
    According to your description, my understanding is that all the used terms cannot display in the Refiners in Content Search web part.
    If the results display in the Search Result Preview, then the terms used in these results can be displayed in the Refiners tab.
    I tested the same scenario per your post, and when I first opened it I can view all the terms which were used in the search results listed under owsmetadatafacetinfo.
    I recommend to do a full crawl and then you can view all the terms used in the search results are displayed under owsmetadatafacetinfo.
    Best regards.
    Thanks
    Victoria Xia
    TechNet Community Support

  • EMC Does Not Show All Databases Copies Information on DAG - Exchange 2010 SP2

    Hi guys,
    Really need your help here, suddenly my customer complain that they cant see any information on database copies on their Active Copy DAG Exchange server, for another DAG members, the database copies information is visible. After do some readings, I found
    this related to Exchange 2010 SP1 known issue. 
    http://workinghardinit.wordpress.com/2010/09/13/emc-does-not-show-all-database-copies-after-upgrade-to-exchange-2010-sp1-still-investigating/
    But, for my environment, there is Exchange 2010 SP2. I have no idea on this issue since there is no error log thrown out from the event viewer. I already try to restart the server itself and the Microsoft Information services but no luck.

    Hi,
    Based on the description, your customers could see passive database copy information, but they couldn’t view the detail information such as state: Healthy in EMC.
    When did this issue begin?
    Please restart the AD topology service to check result.
    Since we have the information correctly on Exchange shell, please try to clear EMC cache and then open console to check if you can see database copy in EMC.
    Best regards,
    If you have feedback for TechNet Subscriber Support, contact
    [email protected]
    Belinda Ma
    TechNet Community Support

  • OUtlook 2013 can not connect to exchange 2013 after exchange maibox member of DAG failed.

    hi ALL
    OUtlook 2013 can not connect to exchange 2013 after exchange maibox member of DAG failed.
    Exchange environment contains 2 Exchange Mailboxesserver ,( one Failed , virtual Machine)
    2 cas Servers
    first databases could not be mounted but after we run the below command , users can use OWA but outlook could not connect
    Start-DatabaseAvailabilityGroup -Identity DAG -MailboxServer MBX1
    please support
    thanks

    Hi,
    According to your description, I understand that Outlook client cannot connect to Exchange server 2013 while one member of DAG failed.
    If I have misunderstand your concern, please do not hesitate to let me know.
    I want to double confirm whether all account store in MBX1 experience this issue, users in MBX2 works fine.
    Please run following command to double check the database status:
    Get-MailboxDatabase –Status | select Name,Mounted,MountedOnServer
    If it works in OWA, the issue may be related to Outlook side. Please run “Test E-mail AutoConfiguration” and “Outlook Connection Status” to get more details, expecial the setting of proxy server, it’s more helpful
    for further troubleshooting.
    Additional, please try to recreate a profile for testing. Besides, please move active DB back to MBX1.
    Best Regards,
    Allen Wang

  • Outlook 2007 does not connect to exchange at computer startup

    Hi all :)
    Here's the situation we're encountring: we are using exchange 2010 with outlook 2007 clients. The issue is that at the startup of the computer, outlook does not connect to exchange (it opens up but it marks that it's not connected to exchange). After trying
    a few times it connects and stays stable (if I close outlook and I open it again, it connects normally).
    This suggests that there's may be a DNS problem: The client is having an issue resolving the name, but once it does and the IP of exchange is available in the cache, outlook doesn't face any issues.
    So I ran some nslookup commands and I noticed the following:
    when I try to resolve the name of exchange, the request times out twice before providing the answer.
    This issue occurs only for forward lookups (when I try to resolve the same IP for the hostname, there's no timeout)
    I also noticed that this issue only occurs when I run nslookup from the client machines (no timeout when I run it from exchange for instance).
    Any ideas about what the problem might be? Could it be something else other than DNS?
    Thank you all for your help.

    Hi all,
    The problem seems not to be related to DNS. Our exchange 2010 organization was actually migrated from a 2007 one. Since then we noticed this issue of outlook taking too much time to connect and sometimes disconnects. I was messing around into adsiedit and
    I noticed that a decomissioned Mailbox Server from our old exchange 2007 organization still exists among the new exchange 2010 objects.
    To further look into it, I ran best practise analyser, the result (to my surprise) was that exchange is still trying to contact the old exchange 2007 server.
    I ran some network trafic captures with Network Monitor, but I was not very successful interpreting anything.
    I uploaded the .cap files with the best practise analyser report and a print screen of the old server into adsiedit objects. I hope you'll be able to help with it.
    I took the network captures on the two CAS Servers (configured in a CAS array) and on a client machine. The IP addresses are as follow:
    client 192.168.0.47
    Domain Controller1 192.168.1.205
    Domain Controller2 192.168.1.213
    CAS1 192.168.2.216
    CAS2 192.168.2.217
    CAS Array 192.168.2.218
    Download Link: https://onedrive.live.com/redir?resid=9360346C01880F58%21935
    Thanks,

  • Mail (Yosemite) not syncing all Exchange mails

    I tried hard it convert from Outlook 2011 to shiny Mail. For me a disaster. Here are my problems with it:
    Mail does not receive all mails. Some are just left out. There seems not to be any rule. Even syncing doesn't change a thing. Some mails stay at the server.
    I send a mail and need the sent mail. I only find this in my Sent folder after a minimum of 15 minutes. Sometimes it takes more than an hour. Syncing or re-starting Mail didn't poke Mail to get these quicker from the server.
    Although the receiving is set to be checked "automatically", it takes up to five minutes to get a new mail after it arrived on the server.
    All the above don't happen with Outlook. Running both applications in parallel will always lead to MS gets the newly arriving mail first. Even a mail sent from Mail appears immediately in Outlook's Sent folder. When you are really a fan you may get around with these two. But not receiving some mails is a no go.

    Sometimes this issue is caused by a misconfiguration or incompatibility of the Exchange server, or perhaps by a bug in Mail. If so, you won't be able to resolve it yourself. The fact that your iOS devices may be working well with the same account isn't relevant, because iOS uses a completely different protocol (ActiveSync) to communicate with Exchange servers. By default, OS X Mail uses the EWS protocol.
    Each of the following steps has been reported to help with Exchange issues, at least temporarily, in some cases:
    1. Back up all data. Open the Internet Accounts pane in System Preferences and check to make sure you don't have duplicate Exchange accounts. If you do, delete all but one of the duplicates. If there are no duplicates, delete the account and recreate it with the same settings.
    2. Rebuild the affected mailbox.
    3. Reindex messages.
    4. Follow the instructions in this support article to disable autodiscovery. You may need to get configuration details from the server administrator.
    5. In the Keychain Access application, delete the password item for the account. The next time Mail tries to access the account, you'll be prompted for the password. Check the box to save it in the Keychain.
    6. If you've created subfolders of the Exchange inbox, log in to the server through its web interface, move the messages out, and remove the subfolders. The inbox should have no subfolders.
    7. Synchronize with the server using IMAP rather than EWS. This is only possible if IMAP is enabled on the server.
    8. Consider using Outlook instead of Mail to access your Exchange mail.
    See also this discussion.

  • The home button for my ipod touch 4th generation does not respond all the time, What do I do?

    The home button for my ipod touch 4th generation does not respond all the time, What do I do?

    Try:
    http://snapguide.com/guides/calibrate-your-home-button/?utm_expid=69945963-15
    fix for Home button
    iPhone Home Button Not Working or Unresponsive? Try This Fix
    - If you have iOS 5 and later you can turn on Assistive Touch it add the Home and other buttons to the iPods screen. Settings>General>Accessibility>Assistive Touch
    - If not under warranty Apple will exchange your iPod for a refurbished one for:
    Apple - Support - iPod - Repair pricing
    You can do it an an Apple store by:
    Apple Retail Store - Genius Bar
    or sent it in to Apple. See:
    Apple - Support - iPod - Service FAQ
    - There are third-party places like the following that will repair the Home button. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens

Maybe you are looking for