Encapsulation dot1q any second any on me3600x

Hi,
we recieve a number of downstream hand-offs that are delivered as SVID/CVID ccts. There are mixture of data, and VOIP subscribers, the only way to tell the different type of subscribers is that the all voip services are marked as cos 4. All data subscribers are marked cos 0. I have no control over the SVID/CVID mix, and there is no "pattern" so I cannot enter ranges.
I am wanting to deliver each subscriber type to a different bridge-domain then use xconnect to forward these so ultimately i have one bridge-domain with VOIP services, and one with data services.
on the me3600x I tried the following:
interface GigabitEthernet0/4
switchport trunk allowed vlan none
switchport mode trunk
service instance 950 ethernet
encapsulation dot1q 1-4096 secondary 1-4096
bridge-domain 950
service instance 951 ethernet
encapsulation dot1q 1-4096 secondary 1-4096 cos 4
bridge-domain 951
This seemed to work with cos 4 traffic being sent to a differnet bridge-domain than other traffic, however when i try to apply this config to more than 4 interfaces (8 bridge-domain members) i get a "command rejected" error when i enter the "encapsulation dot1q" command. "Encapsulation deafult" is still accepted though.
can any one explain to me why there is this limitation, or if there is any way around it, or any other way to do what i am trying to do?
ta.

Hi Mike,
I replicated your setup in the lab and it appears the problematic line causing this interesting limitation is the “encapsulation dot1q any second-dot1q any” under the “service instance 950”
Since you are not really interested in the second tag value you can leave it out of the equation using just “encapsulation dot1q any” –to match any frame (not matching any more specific service instance rules) with at least one 802.1q tag or you can use “encapsulation default” –to match any frame (not matching any more specific service instance rules)
interface GigabitEthernet0/1
switchport trunk allowed vlan none
switchport mode trunk
service instance 950 ethernet
encapsulation dot1q any
bridge-domain 950
service instance 951 ethernet
encapsulation dot1q any second-dot1q any cos 4
bridge-domain 951
c36cx#sh bridge-domain 951
Bridge-domain 951 (6 ports in all)
State: UP                   Mac learning: Enabled
Maximum address limit: 10000
   GigabitEthernet0/1 service instance 951
   GigabitEthernet0/2 service instance 951
   GigabitEthernet0/3 service instance 951
   GigabitEthernet0/4 service instance 951
   GigabitEthernet0/5 service instance 951
   GigabitEthernet0/6 service instance 951
adam

Similar Messages

My iPad keeps locking itself every few seconds, any ideas how to fix it... Drives me mad having to put my pass code in all the time and the screen keeps going blank :( HELP!

My iPad keeps locking itself every few seconds, any ideas how to fix it... Drives me crazy as the screen keeps going blank and I have to constantly put in my pass code every few seconds. Can someone help me out please. The pass code lock is set at 10 minutes but it's happening every few seconds :(

I've run into the issue and it seems to be related to an app not fully supporting the iOS you're on, the reboot doesn't usually solve it.
I've solved it in the following manner(s):
1) Backup the device to iCloud, then erase the iPad (Content and Network Settings).
2) Setup the iPad and choose to restore from iTunes/iCloud Backup (wherever you backed it up)
3) Perform any software updates
I have not tried simply performing the software updates (which may fix it, but if it doesn't you won't be able to perform the above steps).
Enjoy.

Sunce i upgraded my MBP Retina, it became slower than before when i shutdown. Now, it take about 25 seconds to go off while before was about 5 or 6 seconds. any suggestion?

Sunce i upgraded my MBP Retina, it became slower than before when i shutdown. Now, it take about 25 seconds to go off while before was about 5 or 6 seconds. any suggestion?

Have a cup of coffee.

Applying "route-map" in interfaces with encapsulation dot1q

Hello,
I would like to ask you if there were some trouble in applying route-maps in a interface and its subinterfaces, as it is shown:
interface GigabitEthernet0/2
ip address 11.0.9.26 255.255.255.252
ip policy route-map GestionRadios
interface GigabitEthernet0/2.11
encapsulation dot1Q 11
ip address 11.0.9.18 255.255.255.252
ip policy route-map RedOperativaA
interface GigabitEthernet0/2.12
encapsulation dot1Q 12
ip address 11.0.9.22 255.255.255.252
ip policy route-map RedOperativaB
I am not sure if it is correct totally. Besides I get this informacion doing "show ip policy" and it seems to be right.
Router#show ip policy
Interface      Route map
Gi0/2          GestionRadios
Gi0/2.11       RedOperativaA
Gi0/2.12       RedOperativaB
I would be very grateful for your help.
Thanks in advance
Regards,
Sandro

Sandro
We do not have much to work with in your post so giving you really good answers is difficult. You do not tell us what type of device this is (I assume probably a router, but perhaps it is a layer 3 switch?) or what version of code it is running. These things make a difference sometimes in what is supported or is not supported. But since you get output in show ip policy then I assume that the device does support configuration of this feature.
You show us the configuration of the interfaces but not the configuration of the route maps or the access lists which the route maps probably use. So we can not form an opinion of the validity of the route maps or the access lists.
And you do not tell us whether the Policy Based Routing is working or not (and in fact you do not tell us for sure that you are doing PBR - though that is generally what route maps on the interfaces are doing) so we are not clear whether there is a problem here or not.
But based on what you show us in this post I do not see any particular problems with the route maps and the way that you have applied them to interfaces (assuming that your goal is really to do PBR).
HTH
Rick

Frozen during installing updates unresponsive to any commands any ideas?

Screen frozen whilst installing updates unresponsive to any commands any ideas how to come out?

Turn the machine off by holding down the power key for 7-10 seconds. If the machine doesn't boot normally after that, call back.
Just curious - which updates were you installing? I've been having trouble with the Apple software update server for about 17 hours now.
Clinton

HT4623 I updated my iphone 4s on my computer - I lost a lot of pictures - it gave me messages that I had sent back in June and now it wont allow me to play any of my itunes on my phone - any got any solutions to what I should do? HELP

I updated my iphone 4s on my computer - I lost a lot of pictures - it gave me messages that I had sent back in June and now it wont allow me to play any of my itunes on my phone - any got any solutions to what I should do? HELP

I couldn't find the edit button on my original post so I am posting an update here.
I have gone through more apps and have had good luck on all but one more. And it's not that the app doesn't work, I am talking about the Yahoo Weather app, It works fine, but when you swipe between cities the screen lags a bit and it sometimes doesn't move between pages the way it should. On iOS 7.1.2 it was smooth as butter but on iOS 8.0, not so much. I will post a note in the app store to let them know. I really like the Yahoo app better than the new stock app.
I have been going through my games and they all work fine. Angry Birds (Original and Stella), Canabalt, Minecraft, Bejeweled 2, Silly Walks, PopWords, Doodle Jump, Deep Green all seem to work just fine.
Starbucks app works as it should.
I will stop back again next week after I have had the weekend to play with it in detail and post my thoughts again.

When i try to sync my phone to my computer I get a message saying my computer is no longer authorised for purchased items on this iPhone. I go to "store" and it tells me that my computer is authorised. Any one any ideas how I can sync my phone?

when i try to sync my phone to my computer I get a message saying my computer is no longer authorised for purchased items on this iPhone. I go to "store" and it tells me that my computer is authorised. Any one any ideas how I can sync my phone?

Thanks Don-yes i'm using the correct apple id and yes I've plugged the phone into the computer-that's the problem, my computer doesn't recognise my phone anymore altho it comes up in iTunes library it won't sync anymore

My old MBP (2005) often crashes, freezes or shows grey screen at start up. Also track pad often does not work. I have re fomatted the HD and reinstalled system but to no avail. Genius bar says possible faulty HD, but suspect logic board, any ides any body

My old 17" MBP (2005) often crashes, freezes or shows grey screen at start up. Also track pad often does not work. I have re fomatted the HD and reinstalled system but to no avail. Genius bar says possible faulty HD, but I suspect logic board. All checks out OK on the Apple Diagnostic bench. Can a Logic board go intermittant?? Any Ideas any body??

Ive repaired 1000s of laptops over the years (translate: diagnose and replace parts).
Its not that old, Ive owned 100s of laptops (most were free) ....some I still have are nearly 13 years old and still perfect, ....some extremely expensive ones died in under a year.
other than becoming obsolete at some point, there isnt really any "will spoil on" data like Milk for solid state computer parts, ....alas.
You can have a $5000 laptop die in 4 months, and a junker one keep kicking after 10 years.... Ive seen that firsthand countless times.
Common logic dictates that "very expensive = long life" in computers,..... but all the repair people will tell you just the opposite.
I know you have a gripe, I get that all too well honestly .

After upgrading to windows 7, HP CP1215 only prints in black and white !! any Idea any one??

After upgrading to windows 7, HP CP1215 only prints in black and white !! any Idea any one??
Connected to a Dell 1525 laptop via usb cable

Unplug the printer, and uninstall it. Then download the Windows 7 CP1215 plug and play driver package from www.hp.com. Install the printer using that package.
Although I am an HP employee, I am speaking for myself and not for HP.

My apple ID wont accept any cards as payment, so cant buy or update any apps, any help?

My apple ID wont accept any cards as payment, so cant buy or update any apps, any help?

ive registered with a visa debit but it has stopped accepting it but then i tried to re-enter it, and then i tried a mastercard but that was no better

Cannot find '\\file\name'. Verify the path or Internet address is correct. Cannot find any answer any where in this forum.

I cannot find any answer any where in this forum. PLEASE Help!!! I'm receiving this error message every I click on the link, this only happen
on the desktop, but Laptop has no problem to access the file, and everyone else in my group --they don't have issue.
Run Windows 7 Enterprise SP 1, IE ver 9 and 11
Thanks in advance.
Akira

Hi,
Could please clarify the steps to reproduce this issue? Did this issue occur when clicking on a link in an email message within Outlook?
If I didn't misunderstand it, please first try to log into the web mail to check if this issue persists.
If problem didn't exist in webmail, please try to open your Internet Explorer with no add-on mode to troubleshoot the issue. See:
http://support.microsoft.com/kb/976915/en-us
If above didn't fix the issue, please try to reset your Internet Explorer to check the result:
http://support.microsoft.com/kb/923737/en-us
Note: Resetting Internet Explorer isn't reversible, and all previous settings are lost after the reset.
Hope this helps.
Regards,
Steve Fan
TechNet Community Support

Thereis no sound on my macbook air. I have checked the volume and mute controls and the internal speaker are selected. any one any ideas please.

there is no sound on my macbook air. I have checked the volume and mute controls and the internal speaker are selected. any one any ideas please.

Hopefully one of these steps should solve the problem.
1. Remove the headphone.
    If you see red light in the headphone port, plug the headphone
    in and out of the port 5 or 6 times to flip the microswitch inside.
    Sound output may be stuck in the digital mode.
2. Reset PRAM. http://support.apple.com/kb/PH4405
3. Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
4. Applications > Utilities > Audio MIDI Setup
    Audio Devices window
    Side Bar
    Click the Built-in Output.
    Under Mute any of the boxes checked? If so, uncheck it.
Best.

Wifi 802.11n missing? Also the multitasking Any App Any Time is misleading.

All the reviews I read were saying the 4G was supposed to have 802.11N but my new 4G that I just got this morning only sees my 54G network and not the N network. Bummer. Was hoping Wifi would be faster than my old 3G but unless I can't find somewhere to activate this speed I guess those were all false rumors.
Oh and I really don't see any multitasking in my 3rd party apps like the iPhone 4G Apple page says - they say Any app, any time. All my 3rd party apps do is restart when I switch back and forth to them. I don't call that multitasking but rather just a smart shortcut bar that merely remembers the most recent apps I used. Maybe its app dependent, but they shouldn't claim Any App Any Time if it isn't true.

This link should help you a lot: http://db.tidbits.com/article/10125
You must put the 2.4Ghz network with the N as well. It might be only running b/g.
What I did at home was set up AEBS to use 5GHZ to my Mac, and 2.4GHZ for other deviced b/g and N.
The iPad was on the 5GHz as well but somehow (a bug maybe) the 2.4GHz seems better for it as well. Can't explain that.. gave up and 2.4GHZ N it's working fine

Any by Any returns inconsistant results

Hi All, hope someone can help.
Our system is BPC 5.1 MS, running on SQL 2005.
We have a strange issue where the standard Any by Any report provided with the installation is returning inconsistant results.
What is happening is that when I create an Any by Any report, the results in the table do not list all the possible values (i.e. the line/column headers [members] are there, but an amount does not appear in the intersection). The totals at the bottom & right are correct, showing what is in the system.
An evDRE report creating exactly the same layout will show all the values, so the problem is not in the system.
Does anyone have any idea what could be causing this?
Regards,
Peter

Hi Patrick,
Thanks for that SAPNote.
I think that the issue may be along these lines!
The Any by Any is using an evEXP to create it's expansion, the evEXP is referring to an MDX expression.
The problem comes in when looking at the MDX expression ...
1.) The SAPNote is referring to NESTED expansions ... this is not the case in the Any-by-Any
2.) The SAPNote is referring to Dimensions with multiple hierarchies ... but the Any-by-Any gives the same issue even if I choose 2 dimensions that both only have a single hierarchy.
The reason I think we may be on the right track, is that the lines that are missing are exactly the ones that would be expludes by "<>0" ... The problem is that the evEXP is only testing the TOP member chosen, & therefore misses out the ones where there may be values at a lower level, but they nett off.
The SAPNote says that:
"("&$I$24&".Currentmember,["&J25&"])<>0"
Should change to ...
"(["&$I$24&".H1].Currentmember,["&J25&"])<>0"
The Any-by-Any I have has:
"(["&$G$13&"],["&$E$17&"])<>0"
I have tried the following:
1.) Added in .CurrentMember ...
a.)
"(["&$G$13&"].CurrentMember,["&$E$17&"])<>0"
b.)
"(["&$G$13&".H1].CurrentMember,["&$E$17&"])<>0"
2.) Removed the square brackets ...
      a.)
"("&$G$13&",["&$E$17&"])<>0"
      b.)
"("&$G$13&","&$E$17&")<>0"
      c.)
"(["&$G$13&"],"&$E$17&")<>0"
None of the options above work
Any ideas?
PS ... I see my greater than / less than operators are missing just before the zeroes ... they are there, I just can't get them to show on the HTML

My Ipod Video 30 GB isnt playing any songs any more, i can find them all but when i want to play one the player stops at 0:00, and i tried a reset and to formate it and so on but nohting seems to work, what can i do?

My IPod Video 30 GB isn't playing any songs any more, i can find them all but when I want to play one the player stops at 0:00, and I tried a reset and to formatted it and so on but nothing seems to work, what can i do?

Please helm me, has anyone got an idea?

Encapsulation dot1q any second any on me3600x

Similar Messages

Maybe you are looking for