Error-1073807322 occurred at VISA Enable Event

Hi,
I am getting this error in the HP54825A Oscilloscope instrument VI i downloaded. This occurs when I try to run the "Getting Started" VI that came with the driver. This VI was working fine and now all of a sudden it will not work. I have tried redownloading the driver but it stills gives me the same error.
It says:
Possible reasons- VISA (Hex 0xBFFF0026) Specified event type is not supported by the resource.
Any help would be appreciated.
Thanks

Hi gravy,
It is very odd that the VI was working earlier, and now all of a sudden does not. There is probably something that has changed about the application that has created this error.
The first place I would have gone would have been to check and make sure that the VI's code had not been altered in any way, but if that were the case it would have been fixed when you downloaded the driver again. There are a few other possible places that could be the cause of this problem, however. Some things to check are to ensure that all of the inputs are the same and wired into the same terminals on the Getting Started VI, and that all of the settings on the instrument are the same.
If you are sure that the setup is exactly the same, then I recommend running it in highlight execution mode (the lightbulb on the toolbar at the top of the block diagram) to see exactly where this error is occurring. From there we can dig in deeper and see what is going on.
John M
Applications Engineer

Similar Messages

Error -1073807346 occurred at VISA Write in rsspecan_core_write.vi

Possible reason(s):
VISA: (Hex 0xBFFF000E) The given session or object reference is invalid.
I'm using a USB to GPIB connection to a Rohde Schwarz FSV30 Spectrum Analizer from Windows 7.
My program works 100% in LabView but the problem comes in when I've compiled the program into an executable.
I have already installed the NI VISA Run Time Engine 5.0.1 and it still does not work.
I've also installed the NI-488.2 2.73 drivers for the GPIB unit.
Any ideas?
Solved!
Go to Solution.
Attachments:
Error -1073807346 occurred at VISA Write.png ‏30 KB

Hey,
the problem when building executables with LabVIEW is, that the driver core of the attribute based instrument drivers (esp.. the VIs which are creating this error) is linked while runtime dynamically to the VIs. The application builder which follows all dependencies and include them into the package fails in this case.
To get a running executable please add manually all VIs for the folder <inst lib>\rzspecan\_utility\rsspecan_core\callbacks\ to the LabVIEW project and everything should work fine.
For more details of this driver refer to http://www.rohde-schwarz.com/appnote/1ma170
So long, juergen

Error -1073807253 occurred at VISA Read in transient SR830.vi VISA: (Hex 0xBFFF006B) A framing error occurred during transfer.

Hi,
I am have written a program with labview to make transient c-v measurement using a stanford research SR830 lockin amplifier. The program seems to be runing fine, but sometimes it is givvibg an error:
Error -1073807253 occurred at VISA Read in transient SR830.vi
Possible reason(s):
VISA: (Hex 0xBFFF006B) A framing error occurred during transfer.
Error -1073807253 occurred at VISA Read in transient SR830.vi
Possible reason(s):
VISA: (Hex 0xBFFF006B) A framing error occurred during transfer.
but if I press ok, the program again starts running. What might be the poblem? BTW I googled a bit and I see that in the labview topic "RS-232 Framing Error with HP 34401A Mulitmeter" by pkennedy32 this is what is said about framing error:
""Framing Error" in an RS-232 context means a very specific thing - when the receiver was expecting a stop bit, the line was not in SPACE condition. This can be the result of:
1... Baud rate mismatch (although other problems would likely crop up first).
2... Data Length problem, If I send 8 data bits and you expect 7, the stop bit is in the wrong place.
3... Parity setting mismatch - If I send 7 data bits + parity and you expect 7 data bits and no parity, the stop bit is in the wrong place.
4... Mismatch in # Stop bits - If I send you 7 Data bits + parity + one stop bit, and you expect 7 data bits + parity + TWO stop bits, the second one might not be correct, although most devices do not complain about this.
But, I must say that this is the same com port setting that I use to measure c-v hysterysis, but I never gt this error there.
I attach the program herewith for your kind perusal. Please help me resolve this issue.
Thanks in advance.
Solved!
Go to Solution.
Attachments:
transient SR830.vi ‏94 KB
csac.vi ‏8 KB
sr830 initialize1.vi ‏15 KB

@Dennis Knutson you are right I checked the read indicator in backslash mode, and instead of a \n it is sending \r. So I changed the \n in my write strings to \r. But, if I keep the CLOSE VISA outside my loop instead of inside as you suggested, the termination character appears to come in the middle of the read string instead at the end. And since the read terminates at the \r so it is displaying some junk value before the \r, but if I put the CLOSE VISA outside the loop and play along with the bytes at the read buffer, I see the whole read string with the \r at the end of the string. But, whenever the values are in exponential form (when close to zero) like 6.938839 e-5, I always get a time out error whatever be the timeout that I put at the VISA initialize. And subsequently, if I stop the program and run it again the machine program hangs and I donot get any reading. Then after I close it again and start, sometimes it hangs for some more or starts working. If I put an arbitrarily large byte count at the READ VISA, then I always get the time out before the operation completed error.
@ Ravens Fan I have removed the CSAC VI altogether and taking the CH! And CH” reading separately, instead as one string. So, no more issues with that.
I use the control at the delay so that I can choose how much delay I want to set, and I use the math operation because I am using adding up the delay time to keep track of the time elapsed. Because in the end I have t plot a time vs. CH! And CH” readings.
I am not sure but probably I am making some silly errors. Please help me out.
Attachments:
transient SR830-2.vi ‏103 KB
sr830 initialize1.vi ‏15 KB

Error -1073807346 occurred at VISA

My progarm has a very simple Visa write to a E4432 Signal Generator, which worked very good. After sometime Suddenly an error occurs which I cannot understand :" Error -1073807346 occurred at VISA Write in Setting Generator.vi;Possible reason(s):VISA: (Hex 0xBFFF000E) The given session or object reference is invalid."
But when I am using the NI-488.2 Communicator with the same SCPI syntax, it works right away. I chose the right Instrument handler address from the pull up menu of the controller.
What is wrong?
Regards
Yariv

Hi Yariv,
I didn't dig through every part of your code, but for the most part, it looks good. You've got it set up to run the "Quit" case last, which closes out your two VISA sessions before exiting. However, I did notice that on the "Sensitivity check" case, there is a possibility that the Front subVI will pass out a True, which would then stop the while loop immediately without going through the Quit case. If this happens, and something has happened in the SensitivityBlock 1.vi to interrupt the VISA Resource Name wires (and I did notice that these wires were not passed through in all of the cases in this subVI), then the state machine will exit immediately without passing the proper VISA Resource Name values out to the VISA Close VIs.
I also see in your post that you said that this error came back after some changes. When this happens, I would always look very closely at the parts of the program that I modified in order to see what I have changed in order to cause the error. You could also go back to a previously saved version of the program and add the changes one by one, making sure that the program still works at each step.
I won't be able to go through your code extensively, but I recommend tracing through the VISA Resource Name wires and making sure that in every possible scenario, these values get passed through to the close VIs. Good luck with your application!
john

VISA Discard Events Function Fails to Accept "all enabled"

The "VISA Discard Events Function" VI, according to documentation, and also its default value, should accept the "all enabled" event type. This should be a valid input because it is valid to want all events to be flushed. But when given this input the error -1073807322 is output.

That's wierd. Sense it's the default, try running it with nothing connected to that input and see if you still get the error.
TimC
National Instruments
Applications Engineer

Error 1003 occurred at ABAPI Dist Chg and Save VIs.vi

I used to be able to build executable file for my application. However when I upgrade to LV8 and try to build executable file, I got the following message.
Error 1003 occurred at ABAPI Dist Chg and Save VIs.vi -> ABAPI Dist Build LLB Image.vi -> ABAPI Copy Files and Apply Settings.vi -> EBEP_Invoke_Build_Engine.vi -> EBUIP_Build_Invoke.vi -> EBUIP_Build_Invoke.vi.ProxyCaller
Possible reason(s):
LabVIEW: The VI is not executable.
The vi is perfectly executable in LV enviroment.
Anyone know what's going on?
Thanks in advance!

DGU,
Unfortunately this is a known bug in LabVIEW 8.0.1. Our R&D department is well aware of the issue and is currently working on the problem. In the mean time there are some possible work arounds
Check the "Enable debugging"option in the "Advanced Category" of the application executable properties.
Disable the "Remove Panel" option for all SubVIs containing Shared Variables in the build
Try Unchecking the "Disconnect type definitions and remove unused polymorphic VI instances" options also in the Advanced category of the executable properties as shown in the attached figure.
Move shared variables to the top level VIs and pass the data through the SubVI connector
Downgrade to LabVIEW 8.0.
I apologize for the problem. Please let us know if these suggestions help out. Thanks!
Best Regards,
Chris C
Applications Engineering
National Instruments
Chris Cilino
National Instruments
LabVIEW Product Marketing Manager
Certified LabVIEW Architect
Attachments:
1.gif ‏1 KB

An Error occurred in the following Event Subscription: Event Subscription

Dear All,
i got a mail from WF mail which is below:
+From: XXXX WAX [mailto:wfmailer@XXX WAX.com.xx]+
Sent: Monday, March 28, 2011 3:24 PM
To: XXxxHrmsSupport
Subject: Action Required: Local Event ERROR : oracle.apps.ar.hz.Location.update / oracle.apps.ar.hz.Location.update32336
To SYSADMIN
Sent 28-MAR-11 15:23:08
ID 265172
An Error occurred in the following Event Subscription: Event Subscription
Event Error Name:
Event Error Message:
Event Error Stack:
Event Data: Event Data URL
Other Event Details:
Event Field                    Value
Event Name                  oracle.apps.ar.hz.Location.update
Event Key                    oracle.apps.ar.hz.Location.update32336
From Agent                  WF_DEFERRED
From System                 PROD.OWSC.COM
To Agent
To System
Priority                          50
Send Date                  28-MAR-2011 15:20:18
Receive Date              28-MAR-2011 15:21:35
Correlation ID
Parameter : USER_ID 2085
Parameter : RESP_ID 50348
Parameter : RESP_APPL_ID 660
Parameter : SECURITY_GROUP_ID 0
Parameter : ORG_ID 81
Parameter : LOCATION_ID 924
Parameter : #CURRENT_PHASE 101
Parameter : ERROR_TYPE ERROR
Parameter : SUB_GUID A242DC2FF79D70A7E030
Action History
Num
Action Date
Action
From
To
Details 1
+28-MAR-11 15:23:08+
Submit
SYSADMIN
SYSADMIN
Please click on one of the following choices to automatically generate an E-mail response. Before sending the E-mail response to close this notification, ensure all response prompts include a desired response value within quotes.
Retry Raise Event
Retry Raise Event: Abort   Raise Event with Event Key   Raise Event with Event Key and Event Data   Raise with Event Key, Event Data and Parameters Request Information
The client expecting detailed mail regarding this OED.. kindly help me to find this WF mail answer,,
What is this mail, what is the reason, what action i have to take for this ?
Regards
Hameed

Dear Hussein,
Thank you for your support,
You have mention the excat document which is realted to my error.
Oracle.Apps.Ar.Hz.Location.Update / Oracle.Apps.Ar.Hz.Location.UpdateXXXXXX [ID 352888.1]i saw the soultion in this above document, still i have dought will you kindly clarify me !!
· If the event is enabled with subscriptions and that is giving some error message, it means that the user is trying to update the location and he is doing something wrong. Is this correct?
· If I disable the subscription from the production will that create any problem?
Kindly expecting your suggestion
Regards
Hameed
OS: Windows server 2003
Application : 11.5.10.2.0

When trying to work with Agilent 34401A multimeter (serial RS-232 connection), HP34401A Getting Started.vi gives always the message: "Error 1073807369 occurred at Old VISA Open ".

Baud rate and parity are set correctly, RS-232 cable is also connected correctly. My QuickBasic program has no problems to read and write to the Multimeter. It is obviously a software problem: the same error is persistent if I disconnect RS-232 cable.
I downloaded NI-VISA 2.6 for Windows 95/98/NT/ME/2000/XP frorm digital.ni.com and installed it. But it did not help.
Thank you in advance
Best regards
Alexei Soloviev

Hi Steve
I have problems with the 34401A and serial communication. Do you remember
where the error was in the code ?
Thanks
Klaus
wrote in message
news:[email protected]..
> Alexei,
> This may or may not help, I was tasked to do something similar
> recently and found an error in their driver. The GPIB VISA worked
> fine, but when I tried it on serial it played up. There was an errant
> carriage return (or CR/LF I can't remember). GPIB liked one and Serial
> liked the other. It always amuses me that we never have problems with
> Quickbasic!.
> If you want me to dig deeper give me a shout.
>
> Steve Watts
>
> On Thu, 24 Jan 2002 06:16:55 -0800 (PST), "Alexei V. Soloviev"
> wrote:
>
> >When trying
to work with Agilent 34401A multimeter (serial RS-232
> >connection), HP34401A Getting Started.vi gives always the message:
> >"Error 1073807369 occurred at Old VISA Open ".
> >
> >Baud rate and parity are set correctly, RS-232 cable is also connected
> >correctly. My QuickBasic program has no problems to read and write to
> >the Multimeter. It is obviously a software problem: the same error is
> >persistent if I disconnect RS-232 cable.
> > I downloaded NI-VISA 2.6 for Windows 95/98/NT/ME/2000/XP frorm
> > digital.ni.com and installed it. But it did not help.
> >Thank you in advance
> >Best regards
> >Alexei Soloviev
>

Error 1073807202 occurred at Property Node (arg 1) in VISA Configure

I am working with the 30-day evaluation version of LabVIEW
(Version 9.0 32-bit). I am attempting to perform the serial loopback test
described in NI's Developer Zone Tutorial, executing Basic Serial Read and
Write.vi. When I click the Run arrow a dialog box appears with the
following legend:
"Error 1073807202 occurred at Property Node (arg 1) in VISA Configure
Serial Port (Instr).vi>Basic Serial Read and Write.vi. LabVIEW: VISA or
code library could not be located. ...required drive not installed..."
I can find the "smplserl.vi" driver in the /examples folder on my PC.
What's wrong?

Did you do a search for that error? Install NI-VISA.

"Event code: 3008 Event message: A configuration error has occurred" while accessing the sharepoint site.

Hello All,
Wish You Happy New Year to All in advance.
while accessing the share point site i got the error message
Server Error in '/' Application.
Configuration Error
Description: An error occurred during the processing of a configuration file required to service this request. Please review the specific error details below and modify your configuration file appropriately.
Parser Error Message: The element <forms> may only appear once in this section.
Source Error:
Line 104: 
Line 105: <forms loginUrl="/_layouts/log-in.aspx" />
Line 106: <forms loginUrl="/_layouts/log-in.aspx" />
Line 107: <forms loginUrl="/_layouts/log-in.aspx" />
Line 108: </authentication>
Source File: C:\Inetpub\wwwroot\wss\VirtualDirectories\4545\web.config    Line:
106
Version Information: Microsoft .NET Framework Version:2.0.50727.3662; ASP.NET Version:2.0.50727.3658
i have found event message in the event log
Event code: 3008
Event message: A configuration error has occurred.
Event ID: 523cefee6a0943948cf01b4e9f476fff
Event sequence: 77
Event occurrence: 76
Event detail code: 0
Exception information:
    Exception type: ConfigurationErrorsException
    Exception message: The element <forms> may only appear once in this section. (C:\Inetpub\wwwroot\wss\VirtualDirectories\4545\web.config line 106)
Request information:
    Request URL: http://beesppesxapp70:4545/_vti_bin/sitedata.asmx
    Request path: /_vti_bin/sitedata.asmx
    User host address: 172.16.20.80
    User:
    Is authenticated: False
    Authentication Type:
    Thread account name: abc\wss_setup
Thread information:
    Thread ID: 1
    Thread account name: abc\wss_setup
    Is impersonating: False
    Stack trace:    at System.Configuration.BaseConfigurationRecord.EvaluateOne(String[] keys, SectionInput input, Boolean isTrusted, FactoryRecord factoryRecord, SectionRecord sectionRecord, Object parentResult)
   at System.Configuration.BaseConfigurationRecord.Evaluate(FactoryRecord factoryRecord, SectionRecord sectionRecord, Object parentResult, Boolean getLkg, Boolean getRuntimeObject, Object& result, Object& resultRuntimeObject)
   at System.Configuration.BaseConfigurationRecord.GetSectionRecursive(String configKey, Boolean getLkg, Boolean checkPermission, Boolean getRuntimeObject, Boolean requestIsHere, Object& result, Object& resultRuntimeObject)
   at System.Configuration.BaseConfigurationRecord.GetSection(String configKey)
   at System.Web.Configuration.RuntimeConfig.GetSectionObject(String sectionName)
   at System.Web.Configuration.RuntimeConfig.GetSection(String sectionName, Type type, ResultsIndex index)
   at System.Web.Configuration.RuntimeConfig.get_Authentication()
   at System.Web.Security.FormsAuthenticationModule.Init(HttpApplication app)
   at System.Web.HttpApplication.InitModulesCommon()
   at System.Web.HttpApplication.InitInternal(HttpContext context, HttpApplicationState state, MethodInfo[] handlers)
   at System.Web.HttpApplicationFactory.GetNormalApplicationInstance(HttpContext context)
   at System.Web.HttpApplicationFactory.GetApplicationInstance(HttpContext context)
   at System.Web.HttpRuntime.ProcessRequestInternal(HttpWorkerRequest wr)
kindly advise me
Thank a lot in advance

Hi,
As per the error logs it seems you have the Form element twice in your web config file. Just take one or the other one out. if you did any changes in web. config file please share and elaborate little more about the changes if you have made recently before
the error.
Krishana Kumar http://www.mosstechnet-kk.com
Please mark the replies and Proposed as answer if they help and solve your issue

An error has occurred while opening the Premiere Pro CC 2014: Premiere Debug Event

An error has occurred while opening the Premiere Pro CC 2014: Premiere Debug Event
[c: \ cloudroom \ releases \ 2014.9 \ shared \ adobe \ mediacore \ mediafoundation\API\in
I don't know what to do, any help?

Delete the Effect Presets and Custom Items.prfpset, located in
C:\Users\<username>\Documents\Adobe\Premiere Pro\8.0\Profile-<username>
when succesfull make new project and import old one into new one.
Might need to reset current workspace and pull down the audiotracks first to reveal videotracks.

If the LDAP "icsCalendar" value contains a space, an error will occur when creating events or tasks

If a user's LDAP
"icsCalendar" value
contains a whitespace, the user will still be able to log in to the iPlanet
Calendar Server(iCS). However, the user will receive a bad request
error when creating events or tasks. The event or task is created,
but the error will occur every time the user tries to save one.
The "icsCalendar"
preference cannot have a space in it. To avoid the above problem,
the administrator must fix this value in LDAP.

Hi Mahendra,
check the following links:
http://www.sapgenie.com/saptech/lsmw.htm
http://www.scmexpertonline.com/downloads/SCM_LSMW_StepsOnWeb.doc
May be u can find some help.
Hope this helps you.
Regards,
Anuradha.B

Excel Web Access(An error has occurred.Please contact your system administrator if this problem persists. )

I'm using share point 2007 under windows server 2008 R2(one web server, another db server).When I publish a excel(*.xlsx) to report library or view it in web browser with the same error as bellows:
Excel Web Access
An error has occurred.
Please contact your system administrator if this problem persists.
Please kindly support to guide how to fix it with bellow information in details such as log.Many thanks!
1. The 12/logs file is as bellows:
10/10/2014 09:53:55.18 w3wp.exe (0x6528)                       0x5C08 Excel Services
Excel Calculation Services    2u7d Medium ExcelServerSharedWebApplication.Local: An exception was thrown by configdb infrastructure: System.InvalidOperationException: ExcelServerSharedWebApplication.Local: Could
not get ServerContext.Current, which indicates that either SharePoint or the SSP infrastructure isn't provisioned correctly or that we're running outside of a web context.     at Microsoft.Office.Excel.Server.ExcelServerSharedWebApplication.get_Local().
10/10/2014 09:53:55.18 w3wp.exe (0x6528)                       0x5C08 Excel Services
Excel Services Administration 8tqh Critical Excel Services: Unexpected exception while trying to access Shared Services Database;. Error = ExcelServerSharedWebApplication.Local: Could not get ServerContext.Current, which indicates that
either SharePoint or the SSP infrastructure isn't provisioned correctly or that we're running outside of a web context..
10/10/2014 09:53:55.18 w3wp.exe (0x6528)                       0x5C08 Excel Services
Excel Web Access              6nfi Unexpected InternalEwr.OpenWorkbook - An unexpected exception in the ECS Proxy occurred. Message: Microsoft.Office.Excel.Server.ExcelServerSettingException:
An error has occurred. ---> System.InvalidOperationException: ExcelServerSharedWebApplication.Local: Could not get ServerContext.Current, which indicates that either SharePoint or the SSP infrastructure isn't provisioned correctly or that we're running
outside of a web context.     at Microsoft.Office.Excel.Server.ExcelServerSharedWebApplication.get_Local()     --- End of inner exception stack trace ---     at Microsoft.Office.Excel.Server.ExcelServerSharedWebApplication.get_Local()
at Microsoft.Office.Excel.Server.ExcelServerSettings.get_Settings()     at Microsoft.Office.Excel.Server.ExcelServerSettings.get_EcsList()     at Microsoft.Office...
2.the event in event viewer is:
Log Name:      Security
Source:        Microsoft-Windows-Security-Auditing
Date:          2014/10/10 9:49:43
Event ID:      4625
Task Category: Logon
Level:         Information
Keywords:      Audit Failure
User:          N/A
Computer:      ***.net
Description:
An account failed to log on.
Subject:
Security ID:  NULL SID
Account Name:  -
Account Domain:  -
Logon ID:  0x0
Logon Type:   3
Account For Which Logon Failed:
Security ID:  NULL SID
Account Name:  ***
Account Domain:  ***
Failure Information:
Failure Reason:  An Error occured during Logon.
Status:   0xc000006d
Sub Status:  0x0
Process Information:
Caller Process ID: 0x0
Caller Process Name: -
Network Information:
Workstation Name: ***
Source Network Address: ***
Source Port:  63664
Detailed Authentication Information:
Logon Process:
Authentication Package: NTLM
Transited Services: -
Package Name (NTLM only): -
Key Length:  0
This event is generated when a logon request fails. It is generated on the computer where access was attempted.
The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe.
The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network).
The Process Information fields indicate which account and process on the system requested the logon.
The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases.
The authentication information fields provide detailed information about this specific logon request.
- Transited services indicate which intermediate services have participated in this logon request.
- Package name indicates which sub-protocol was used among the NTLM protocols.
- Key length indicates the length of the generated session key. This will be 0 if no session key was requested.
Event Xml:
<Event xmlns="">
<System>
    <Provider Name="Microsoft-Windows-Security-Auditing" Guid="{54849625-5478-4994-A5BA-3E3B0328C30D}" />
    <EventID>4625</EventID>
    <Version>0</Version>
    <Level>0</Level>
    <Task>12544</Task>
    <Opcode>0</Opcode>
    <Keywords>0x8010000000000000</Keywords>
    <TimeCreated SystemTime="2014-10-10T01:49:43.563436300Z" />
    <EventRecordID>37602685</EventRecordID>
    <Correlation />
    <Execution ProcessID="532" ThreadID="26096" />
    <Channel>Security</Channel>
    <Computer>***.net</Computer>
    <Security />
</System>
<EventData>
    <Data Name="SubjectUserSid">S-1-0-0</Data>
    <Data Name="SubjectUserName">-</Data>
    <Data Name="SubjectDomainName">-</Data>
    <Data Name="SubjectLogonId">0x0</Data>
    <Data Name="TargetUserSid">S-1-0-0</Data>
    <Data Name="TargetUserName">***</Data>
    <Data Name="TargetDomainName">***</Data>
    <Data Name="Status">0xc000006d</Data>
    <Data Name="FailureReason">%%2304</Data>
    <Data Name="SubStatus">0x0</Data>
    <Data Name="LogonType">3</Data>
    <Data Name="LogonProcessName">
    </Data>
    <Data Name="AuthenticationPackageName">NTLM</Data>
    <Data Name="WorkstationName">***</Data>
    <Data Name="TransmittedServices">-</Data>
    <Data Name="LmPackageName">-</Data>
    <Data Name="KeyLength">0</Data>
    <Data Name="ProcessId">0x0</Data>
    <Data Name="ProcessName">-</Data>
    <Data Name="IpAddress">***</Data>
    <Data Name="IpPort">63664</Data>
</EventData>
</Event>

Hi Tracy,
Have you changed something on your SharePoint 2007 environment recently before this issue occurred?
This issue may be related to Alternate Access Mappings settings like the following similar post, if you have configured AAM, you can check if this issue happened to some URLs, if it's the case, please add the problematic URLs as a Publish URLs for the default
zone for your web application, and also add these URLs as trusted locations, then check results again.
If above doesn't work, please enable ULS log on verbose level to get more useful log errors which time are corresponding to the errors occur.
https://social.technet.microsoft.com/Forums/en-US/c9ab4818-65c9-444d-be50-1bfed1f1509b/excel-web-access-web-part-works-on-intranet-but-not-internet?forum=sharepointgenerallegacy
http://blog.bugrapostaci.com/2011/09/08/how-to-enable-verbose-log-mode-on-moss-2007/
Thanks
Daniel Yang
TechNet Community Support

An error has occurred:Invalid postback or callback argument in InfoView

Hi Friends,
When i try to change the parameter values and click OK button while scheduling a report in InfoView, i am getting the following error:
An error has occurred:Invalid postback or callback argument. Event validation is enabled using in configuration or in a page. For security purposes, this feature verifies that arguments to postback or callback events originate from the server control that originally rendered them. If the data is valid and expected, use the ClientScriptManager. RegisterForEventValidation method in order to register the postback or callback data for validation.
Till now i have not find any good solution for this. Please help in providing any better solutions to fix this.
Edited by: Shivananda Puli on Aug 6, 2010 11:55 AM
Edited by: Shivananda Puli on Aug 6, 2010 11:55 AM

This forum is for questions in regards to using the SDK within a custom application, since you are using Infoview, please post this in the applicable forum under the [Business Objects|/community [original link is broken]; section

Build error after upgrading from 8.2.1 to 8.5 "Error 1055 occurred at Invoke Node..."

After upgrading to 8.5, I'm getting the following error when trying to build an EXE:
Visit the Request Support page at ni.com/ask to learn more about resolving this problem. Use the following information as a reference:
Error 1055 occurred at Invoke Node in AB_Source_Library.lvclass:Close_Reference.vi->AB_Build.lvclass:Copy_Files.vi->AB_Application.lvclass:Copy_Files.vi->AB_Build.lvclass:Build.vi->AB_EXE.lvclass:Build.vi->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
Possible reason(s):
LabVIEW: Object reference is invalid.
I have been building this application for both Windows and Mac OS, and I even get the same error when building the .app on an Intel Mac.
Things that I've already tried:
* Mass-compiling all my code
* Created the project from scratch
* Enabled each panel of the "diagram disable structure" one at a time and compiled again
Any ideas?

Hi Travis,
Ben’s advice if definitely the best place to start. Error 1055 is a very general LabVIEW error for “Object reference is invalid.” The cause is usually a bad install where important LabVIEW function aren’t placed in the right directory or aren’t installed at all.
Charlie M. CLD

Error-1073807322 occurred at VISA Enable Event

Similar Messages

Maybe you are looking for