Error "Device identifier is invalid" USB-6501???

HI
When i run the script "USB-6501 Interactive Control.llb", i have this error  "Device identifier is invalid"?
If you know another script that drives the "USB-6501" to check its lines,  please help me?
Best regards      
Solved!
Go to Solution.

USRP wrote:
When i run the script "USB-6501 Interactive Control.llb", i have this error  "Device identifier is invalid"?
What do you mean by When i run the script "USB-6501 Interactive Control.llb"...???
--> Do you've USB 6501 listed in MAX, as shown in the picture below...???
--> Are you using correct string identifier as device name...???
I am not allergic to Kudos, in fact I love Kudos.
 Make your LabVIEW experience more CONVENIENT.

Similar Messages

  • Device identifier is invalid error 200220

    I developed a program on one computer using LabView 8, DAQmx 8 and a USB-6008 device. It worked fine at my desk. Then I save the program as a project sent it acroos the street to our shop, took the device over there plugged it in and tried to run the program. I got a 200220 Device identifier is invalid error. When I pull up MAX I can see the device and if I build a tsk on that computer for that device it runs fine but it will not run the program that I brought over from my desk computer. Any Idea what I'm doing wrong?
    TIA
    George

    Munir,
    I'm sure some of the other can better answer your question as I too am a LabView newbie, but I'll tell you what I know.
    1)What is the Development system. How can I know if both are Device1 or whatever is appropriate.
     My development system was my desk computer, I used another PC out in the shop as a deployment computer to attach my DAQ device and run my program.
    2)I am using examples for LABVIEW.
    The examples are code that someone wrote on another machine so the device that they specify might not be the same as the one on your machine.
    In my case my USB device that I was using as my DAQ was named Dev2 on the computer at my desk that I wrote the program on. However when I took the DAQ device down to the computer in my shop to run the program it was named Dev1 because there were no other devices on that computer. There was no Dev2 on the shop computer so when I tried to run the code it crashed as it could not find a Dev2 to get the data signals from.
    Tom's request of "If you can get screenshots of the NI-DAQmx Devices and Data Neighborhood trees from MAX that would also help."
     would be a good place for you to start.
    I hope this helps
    George

  • "Device Identifier is invalid" Error -200220 on Linux

    I searched the forums, but didn't see anything about this for Linux (Red Hat 4).  The issue is that when I try to create a virtual channel in the "DAQmxBase Create Channel" vi , I get the error message "Device Identifier is invalid", which is strange since the device name (Dev2/ai0) is provided by browsing the "physical channels" text box. 
    Additionally, running the command "nidaqmxconfig --export daqmx.ini" and looking in the .ini file shows that the device is recognized by LabVIEW (shown below).
    [zieve@he3 ~]$ nidaqmxconfig --export daqmx.ini
    Operation successful.
    [zieve@he3 ~]$ more daqmx.ini
    [DAQmx]
    MajorVersion = 8
    MinorVersion = 0
    [DAQmxDevice Dev2]
    ProductType = PCI-6220
    DevSerialNum = 0x12900B7
    BusType = PCI
    PCI.BusNum = 0x6
    PCI.DevNum = 0x8
    Any help would be appreciated.

    Hi ZeroShado,
    Can you please clarify what driver and version you are
    using? Your post says you are having a problem with a DAQmx Base VI, but later
    states that you have regular DAQmx 8.0. Do you have both installed, but are
    using DAQmx base to program? DAQmx 8.0 is only supported on Red Hat Enterprise
    Linux WS 3.
    I may suggest looking through some of the Linux forums as
    well, here, here, and here.
    David L.
    Systems Engineering
    National Instruments

  • Device identifier is invalid

    I am a complete newbie and am trying to use my brand new PCI-6601.  Measurement & Automation Explorer reports the name of the board as "Dev1" and the test panel application that uses "Dev1/ctr0" works properly.  However, when I compile and run the cntDigEvents.c example program provided with NIDAQmx, I get an error message "DAQmxBase Error: <err>Device identifier is invalid".  The device name ("chan[]") used in the example program is Dev1/ctr0 which seems to me to be correct.
    Any help would be greatly appreciated!

    marc,
    DAQmx Base is our platform-independent driver which can be used on Windows, Linux, Mac, and PDA. If you will be developling solely for Windows, I would recommend using NI-DAQmx (no Base) as it exposes more of the functionality of your device.
    Hope this helps,
    Ryan Verret
    Product Marketing Engineer
    Signal Generators
    National Instruments

  • Error -200220 LabView 7.1 USB 6008

    I have two PC one with LabView 7.0 another one with LabView 7.1 and NI-DAQmx Base 1.4 installed for USB 6008.
    If I run example VI for LabView 7.0 on first PC it works OK, but  on second one I get Error -200220 occurred at an unidentified location Possible reason(s):
    Device identifier is invalid.
    Can someone explain me what to do with this error.
    I already tried to update LabView to 7.1.1. and drivers to 7.5 but things are getting even worse with it so I reinstalled all back.
    Can somebody give me simple VI example for this device (for examle AI monitoring) and may be you can help me with this error.
    Sergey.

    Sergey,
    If i'm being totally honest, I would ditch DAQmx Base and move to DAQmx 7.5, in the long run this will make things ALOT easier.
    From your previous post, I'm guessing you already have 7.5 downloaded or on disc somewhere. Install this driver instead. The following guide may help you out:
    http://digital.ni.com/manuals.nsf/websearch/5F6EEBAF2522C98B862570120052F35F
    As soon as you run into any problems, let me know by posting here and I will work through them with you.
    One other thing I would mention is that you may be experiencing problems that have arisen due to multiple install/uninstalls, and the registry may have been mixed and that's why you are having the trouble.
    Let me know how your getting on and we can progress together!

  • Usb 6501 unresponsive causing BSOD(Blue Screen Error)

    There are a lot posts about the same issue but mine is a little peculiar so i decided to post it.
    I am using two usb DAQ in the same pc(usb-6501, usb-6001), connected to the usb port on the back. The usb-6501 is used to obtain digital inputs from read switches, Sensors through an ssr. The usb-6001 is used to control 2 double valve solenoid, 1 dc motor, 2 indicator lamps. usb-6001 is also used to read analog values of current(using hall effect sensor) and voltage(using potentiometer).
    At first i was facing problems with the usb-6001(the usb-6501 was working fine at this point) resetting during operation accompanied by BSOD. Then i learned it was due to my relay, which requires 30 mA of current to switch so i used the ULN2003a to interface the usb-6001 with the relays and after that the application was running perfectly for 4 days.
    Now the usb-6501 is having the same problem and when i perform "Self Test" from NI MAX it shows "Error Code:50405" and i am able to reset the device from NI MAX only sometimes, other times i would have to unplug the USB device then plug it back in. As the application is used for an automated test rig the customer is frustrated by this problem. Once the card becomes unresponsive(or after the card is reset) BSOD occours.
    I have checked all the device drivers and OS for any errors but they are fine. i have even tried changing the ram to solve the BSOD with no use.
    System Details:
    Windows 7 SP1
    NI MAX 14.0
    power saving is disabled 
    I have attached the latest mini dump files as they might help in finding out the reason behind this problem(File extensions changed for the purpouse of uploading).
    I need to know: Is there any permanent solution for this problem? and what is the reason for this problem.
    Attachments:
    060115-12480-01.txt ‏315 KB
    053015-12324-01.txt ‏315 KB
    052615-17440-01.txt ‏315 KB

    Additional info : i did an analysis of the dump files and this is the result
    0: kd> !analyze -v
    * Bugcheck Analysis *
    DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1)
    An attempt was made to access a pageable (or completely invalid) address at an
    interrupt request level (IRQL) that is too high. This is usually
    caused by drivers using improper addresses.
    If kernel debugger is available get stack backtrace.
    Arguments:
    Arg1: fffff88009fe10b1, memory referenced
    Arg2: 0000000000000002, IRQL
    Arg3: 0000000000000000, value 0 = read operation, 1 = write operation
    Arg4: fffff8800657922e, address which referenced memory
    Debugging Details:
    READ_ADDRESS: GetPointerFromAddress: unable to read from fffff800032c30e8
    fffff88009fe10b1
    CURRENT_IRQL: 2
    FAULTING_IP:
    nifslk+822e
    fffff880`0657922e 0fb650ff movzx edx,byte ptr [rax-1]
    CUSTOMER_CRASH_COUNT: 1
    DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
    BUGCHECK_STR: 0xD1
    PROCESS_NAME: System
    TRAP_FRAME: fffff80000b9c6b0 -- (.trap 0xfffff80000b9c6b0)
    NOTE: The trap frame does not contain all registers.
    Some register values may be zeroed or incorrect.
    rax=fffff88009fe10b2 rbx=0000000000000000 rcx=0000000000000000
    rdx=fffff80000b9c8e0 rsi=0000000000000000 rdi=0000000000000000
    rip=fffff8800657922e rsp=fffff80000b9c840 rbp=fffff88009fe10b1
    r8=0000000000000000 r9=0000000000000000 r10=0000000000000000
    r11=0000000000000000 r12=0000000000000000 r13=0000000000000000
    r14=0000000000000000 r15=0000000000000000
    iopl=0 nv up ei ng nz na po nc
    nifslk+0x822e:
    fffff880`0657922e 0fb650ff movzx edx,byte ptr [rax-1] ds:c8e0:fffff880`09fe10b1=??
    Resetting default scope
    LAST_CONTROL_TRANSFER: from fffff80003091be9 to fffff80003092640
    STACK_TEXT:
    fffff800`00b9c568 fffff800`03091be9 : 00000000`0000000a fffff880`09fe10b1 00000000`00000002 00000000`00000000 : nt!KeBugCheckEx
    fffff800`00b9c570 fffff800`03090860 : fffffa80`06adc250 fffffa80`05c3a060 fffffa80`06adc250 00000000`0000ffff : nt!KiBugCheckDispatch+0x69
    fffff800`00b9c6b0 fffff880`0657922e : fffff880`05d47468 fffff880`01d91f90 00000000`00000000 fffff880`09fe0770 : nt!KiPageFault+0x260
    fffff800`00b9c840 fffff880`05d47468 : fffff880`01d91f90 00000000`00000000 fffff880`09fe0770 fffff880`09fe17a0 : nifslk+0x822e
    fffff800`00b9c848 fffff880`01d91f90 : 00000000`00000000 fffff880`09fe0770 fffff880`09fe17a0 fffff880`09fe10b1 : 0xfffff880`05d47468
    fffff800`00b9c850 00000000`00000000 : fffff880`09fe0770 fffff880`09fe17a0 fffff880`09fe10b1 fffff800`00b9c8e0 : nipalk+0x75f90
    STACK_COMMAND: kb
    FOLLOWUP_IP:
    nifslk+822e
    fffff880`0657922e 0fb650ff movzx edx,byte ptr [rax-1]
    SYMBOL_STACK_INDEX: 3
    SYMBOL_NAME: nifslk+822e
    FOLLOWUP_NAME: MachineOwner
    MODULE_NAME: nifslk
    IMAGE_NAME: nifslk.dll
    DEBUG_FLR_IMAGE_TIMESTAMP: 51f2daeb
    FAILURE_BUCKET_ID: X64_0xD1_nifslk+822e
    BUCKET_ID: X64_0xD1_nifslk+822e
    Can anyone help me with what this means?

  • Hi I recently dropped my ipod touch and now it wont connect to itunes. Everytime i plug it in, i get an error message saying that the usb device is not recognized

    hi I recently dropped my ipod touch and now it wont connect to itunes. Everytime i plug it in, i get an error message saying that the usb device is not recognized

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • [cl_invalid_operation] OpenCL Error : Failed to retrieve device information! Invalid enumerated value!

    I am having random playback glitches on my Mac Pro 2014 using Premiere CC 7.2.2 and Media Encoder. I can't figure out the cause since its only in the playback and export of the footage. The source footage is glitch free.
    I have noticed these two warnings when loading Premiere and Media Encoder.
    [cl_invalid_operation] OpenCL Error : Failed to retrieve device information! Invalid enumerated value!
    Are the glitches due to this OpenCL Error and how can I fix it?

    That's 7.2. I'm on 7.2.2. which rolled out 4/23/2014. Never the less thanks for finding that link. I dont have crash issues with playback or fx. Just random playback glitches.
    Are you stating that the OpenCL error is caused by a software glitch from adobes end?

  • The File name property is not valid. The file name is a device or contains invalid characters

    I have an SSIS task that has run successfully for years. They just moved the dtsx to a new server and now it is failing. 
    Issue:
    The task has a data flow that writes a raw file destination. It then has a subsequent data flow that reads the raw file destination. 
    The path and name of the raw file is passed to each of the data flows via the same variable. 
    The raw file resides in a folder on the server in the same path that the dtsx resides in. 
    The task fails with the "The File name property is not valid. The file name is a device or contains invalid characters" error when trying to access the raw file.
    What we have done to troubleshoot:
    1. I ran the task successfully on my local machine so it is definitely a server issue.
    2. The first thing we were seeing was that it failed trying to write to the raw file. The task is set to "Create Always". 
    3. We saw that the dba's copied over the entire directory structure from the old server which included a previously created raw file, so we deleted the raw file.
    4. We reran the task and it successfully wrote a new raw file but then failed on reading the raw file with the same error as above.
    5. We reran the task AGAIN and this time it failed trying to write the raw file throwing the same error as above.
    6. The dba looked at the directory and the account that performs the task has full control.
    7. The dba looked at the raw file that was created and verified that the account that performs the task has full control of the file and that it is the owner of the file.
    Summary:
    The task fails when trying to access the file EXCEPT when the file does not exist. In that situation it can write the file but subsequently fails in accessing it again.

    Hi Whalensdad,
    Based on my research, the issue can be caused by the following reasons:
    There are some invalid characters in the File name at package runtime. In this scenario, just as Russ said, could you please post the value that is in the File name variable? Also use a Script Task with Messagebox.show to show the variable values at runtime.
    May be it changes to others at run time.
    The account runs the package not having access to all the folders in the path. Since you are moving the dtsx file from one server to the current server, do you also move the raw file to the same folder in the current server? Does the user runs the package
    have access to all the folders in the path? To solve this, please ensure that the user has access to all folders and the raw file in the path on the current server.
    Thanks,
    Katherine Xiong
    If you have any feedback on our support, please click
    here.
    Katherine Xiong
    TechNet Community Support
    Please see the response above. I can't use a message box on a server so I logged the values to the database. The resource account has full control to the folder. I haven't been able to get the DBA to check the SQL Agents permissions, but I was always under
    the impression that if you use "Run As" on the task, it will not use the SQL Agent but the account you identify it to "Run As". The "Run As" account has full control on the folder and file.

  • Annoying error message: ieee80211 phy0: invalid plcp cck rate (0)

    Greetings Fellow Forumers!
    I have an annoying issue caused by (I think) the firmware (carl9170) necessary to allow my USB NIC to work.  The issue itself is that this message will pop up on my console and TTY:
    ieee80211 phy0: invalid plcp cck rate (0)
    I have searched the forums and found nothing (as of yet). I have, however, found some sparse information on the Internet but it isn't very helpful.  Most of what I've read describes the behaviour itself (the error messages spamming the screen) and developers who figured out that it is the firmware causing this behaviour.  I have yet to find information about how to solve this issue and stop the error from repeating itself ad nauseum.  What I have read so far also hasn't cast any illumination about the underlying cause as to why the error message is being printed in the first place.
    LSHW shows this about the USB device itself:
    bus info: usb@2:2
    logical name: wnet
    capabilities:
    ethernet,
    Physical interface,
    Wireless-LAN
    configuration:
    broadcast: yes
    driver: [i]carl9170[/i]
    driverversion: 3.15.8-1-ARCH
    firmware: 1.9.6
    ip: 192.168.1.74
    link: yes
    multicast: yes
    wireless: IEEE 802.11abgn
    If all I can do is suppress this message I'll be happy with that.  Admittedly, though, I'll need a hint or two about how to do that. 

    Greetings Fellow Forumers!
    I have an annoying issue caused by (I think) the firmware (carl9170) necessary to allow my USB NIC to work.  The issue itself is that this message will pop up on my console and TTY:
    ieee80211 phy0: invalid plcp cck rate (0)
    I have searched the forums and found nothing (as of yet). I have, however, found some sparse information on the Internet but it isn't very helpful.  Most of what I've read describes the behaviour itself (the error messages spamming the screen) and developers who figured out that it is the firmware causing this behaviour.  I have yet to find information about how to solve this issue and stop the error from repeating itself ad nauseum.  What I have read so far also hasn't cast any illumination about the underlying cause as to why the error message is being printed in the first place.
    LSHW shows this about the USB device itself:
    bus info: usb@2:2
    logical name: wnet
    capabilities:
    ethernet,
    Physical interface,
    Wireless-LAN
    configuration:
    broadcast: yes
    driver: [i]carl9170[/i]
    driverversion: 3.15.8-1-ARCH
    firmware: 1.9.6
    ip: 192.168.1.74
    link: yes
    multicast: yes
    wireless: IEEE 802.11abgn
    If all I can do is suppress this message I'll be happy with that.  Admittedly, though, I'll need a hint or two about how to do that. 

  • Pulselength USB 6501

    Hello,
    I want to use one or more USB 6501 Boards to fire up some 10s of IGBTs. Each of these switches turns on ~10A for 1ms-3ms (each IGBT has a different turn-on length). Since the pulse pattern repeats after at least 40ms, i want to fire them step by step to minimize the stress for my main power line.
    I managed to create a VI which does exactly what I want - with one exception: The digital waveform gets created from an array using "build waveform". But no matter what value I feed into "dt" to control the length of each digit/pulse, all I get is pulses of 1 ms for each logical "1".
    From my point of view, "dt" tells the Channel how long it should stay "high" for each "1" it receives. Is this incorrect? I want to control the length of each pulse in steps of 0.1 ms - in other threads I read something about the need to use some kernel-functions to be able to use sub-millisecons resolutions. If this is correct, shouldn´t I be able to see a 2 ms pulse when setting "dt" to 0.002?
    Thank you for every hint, Sascha
    BTW: Labview 8.5 Evaluation / Labview 6.1 full
    BTW2: In the attached file you will only find 8 digital waveforms for 24 digital ports... I don´t know how to save the full 24*20 binary array, therefore you will receive an error if you try to run this VI without correcting the number of physical ports to use.
    Attachments:
    IGBT.vi ‏49 KB
    6501.png ‏53 KB

    Hello Philosoph,
    the USB-6501 is a static DIO device, which means it does not have an onboard clock to switch the digital ports with a certain frequency.
    You can turn on and off the digital lines with software timing in LabVIEW. That is ok if the timing does not have to be very accurate - i.e. it does not matter if the pulse is 10 ms or 12 ms - and if the frequency is not too high.  A pulse length of 1 ms is borderline - most of the time, it will probably work, but when your PC does have to do other tasks, you might get a delay of up to  100 ms. In any case, you will have a jitter on the pulse length. For higher timing accuracy requirements, you would have to use a DIO device with correlated, which means clocked, outputs.
    Having said that, I would recommend a different approach for the signal generation. I attached a VI that writes state information to the digital outputs; you can modify the digital pattern in the array, and set the desired pulse length. As the first iteration of "Wait for next ms multiple" does not have a determined duration, I would leave the first line all zeros and start signal generation with the second line. If needed, you can wrap the for-loop in another loop to repeat the pattern.
    Regards,
    Johannes
    NI Germany
    Attachments:
    Digital Signal - static.vi ‏19 KB

  • How to I connect Sourcing digital output from My Interface Board to NI USB 6501 channel configured as Digital input

    When I connect an input to DI channel of USB 6501 card  from my board which has sourcing Output t, iIn the Off state it is not pulled down properly. The volatge on the port in is 2.1V -2.5V based on the pull down resistor on my board. I suspect that  it acts as a voltage divider.
    The state on the card is still show as "HIGH "state, even my sourcing output driver has a pull down  resister.  when I use this interface board for PCI mseries devices it works fine. Do the pull down resister on my sourcing output is not worth. Is this because of pull up resister 4.7k inside USB card 6501.
    USB 6501 specifications shows the Digital input accepts both source and sink modes. By default the card is in sourcing digital input mode. How do we can convert this in Sinkind digital input mode.
    Could anyone Please give your suggestions to overcome this issue .
    Thanks you.

    You really should not have both a pull up and pull down on the same line.  Really weird things can happen.  If you insist on having a pull down on your board, then I highly recommend putting a digital buffer chip between the DAQ and your board.
    Some boards with DIO have a pull up, while others have pull down.  You just have to watch the specs.
    There are only two ways to tell somebody thanks: Kudos and Marked Solutions
    Unofficial Forum Rules and Guidelines

  • Can I measure period with USB 6501?

    Hi,
    I was told that I can use the one counter in the NI USB 6501 to measure period.  So, I wrote this little VI, modeled after the VI I have that measures encoder period using the counters built into the NI cDAQ 9174 with the NI 9401 digital I/O module.  I have my encoder wires GND and 5VDC on terminals 1 and 2, respectively.  Also, I have encoder channel A and Channel B wires connected to terminals 9 (P2.7) and 24 (P0.7) respectively.  With the MAX, I can count edges with this wiring.  The purpose of this VI is to display an average value of 25 period measurements of the encoder.  The encoder (120 cpt) is turning at about 2-5 rev/second, so, not that fast, maybe a total of 500 period per second; should be easy for this counter.  I'm just spinning it with my finger, so, not that fast.
    Please advise how to use the USB 6501.  I can't find any wiring instructions, other than the pinout, but, the pinout doesn't tell you which channel is the counter gate on the USB 6501, so, I found a response on MAX at channel 24.
    When I run this, the array is correctly initialized to 0.5, but, then I get this error, 200431. I found some things on the forum that suggest I cannot measure period, that I can only count edges.  Should I throw this 6501 away?
    Thanks,
    Dave
    Attachments:
    USB 6501 error.docx ‏24 KB
    USB 6501 period measurement.vi ‏26 KB

    The 9178 also only has 4 counters.
    Do the 5 period measurements actually have to take place at the same time?  Sometimes it might make sense to cycle through the channels to reduce the number of counters used (you wouldn't have to rewire connections or anything as the input terminals are software-defined).  Switching from channel to channel in software should take on the order of ms depending on which hardware you end up using.
    The 9171+(9401/9402) is a relatively cheap way to add additional counters to a system as the 9171 chassis has 4 counters just like the 9174 and 9178.
    Best Regards,
    John Passiak

  • ORA-00205: error in identifying control file while startup database

    Dear Experts,
    we are using Oracle 10g on RHEL5.4 64Bit ecc 6.0 with eph 4 i have moved all my sap data files along with Temp file.
    when i startup my database getting error.
    SQL> startup mount
    ORACLE instance started.
    Total System Global Area 535662592 bytes
    Fixed Size 1334380 bytes
    Variable Size 306185108 bytes
    Database Buffers 222298112 bytes
    Redo Buffers 5844992 bytes
    ORA-00205: error in identifying control file, check alert log for more info
    when i checked initSID.ora then found old location of control file.
    1)/oracle/SID/sapdata1/cntrl
    2)/oracle/SID/origlogA/cntrl
    3)/oracle/SID/origlogB/cntrl
    i have manually changed location of control file.
    1)/oracle/SID/sapdata10/cntrl
    2)/oracle/SID/origlogA/cntrl
    3)/oracle/SID/origlogB/cntrl
    SQL> Create Pfile from Spfile;
    File Created.
    i would like to mount my database from Pfile plese help me i execute scripts below.
    SQL> STARTUP MOUNT=/oracle/SID/ORACLE_HOME/dbs/initSID.ora
    invalid startup option.
    or suggest me some other way so that i can startup my Database.
    with Regards

    Thanks,LOG of alert_SID.log  control_files            = /oracle/PRD/origlogA/cntrl/cntrlPRD.dbf, /oracle/PRD/origlogB/cntrl/cntrlPRD.dbf, /oracle/PRD/sapdata1/cntrl/cntrlPRD.dbf, control_file_record_keep_time= 30, Mon Nov 14 08:24:52 2011
    CREATE DATABASE PRD CONTROLFILE REUSE  MAXLOGFILES 255 MAXLOGMEMBERS 3 MAXLOGHISTORY 1000 MAXDATAFILES 254 MAXINSTANCES 50 NOARCHIVELOG CHARACTER SET UTF8 NATIONAL CHARACTER SET UTF8 DATAFILE '/oracle/PRD/sapdata1/system_1/system.data1' SIZE 350M REUSE AUTOEXTEND ON NEXT 20M MAXSIZE 10000M EXTENT MANAGEMENT LOCAL DEFAULT TEMPORARY TABLESPACE PSAPTEMP TEMPFILE '/oracle/PRD/sapdata1/temp_1/temp.data1' SIZE 570M REUSE AUTOEXTEND ON NEXT 20M MAXSIZE 10000M UNDO TABLESPACE PSAPUNDO DATAFILE '/oracle/PRD/sapdata1/undo_1/undo.data1' SIZE 700M REUSE AUTOEXTEND ON NEXT 20M MAXSIZE 10000M SYSAUX DATAFILE '/oracle/PRD/sapdata1/sysaux_1/sysaux.data1' SIZE 200M REUSE AUTOEXTEND ON NEXT 20M MAXSIZE 10000M
    LOGFILE GROUP 1 ('/oracle/PRD/origlogA/log_g11m1.dbf',
    '/oracle/PRD/mirrlogA/log_g11m2.dbf') SIZE 50M  REUSE ,GROUP 2 ('/oracle/PRD/origlogB/log_g12m1.dbf',
    '/oracle/PRD/mirrlogB/log_g12m2.dbf') SIZE 50M  REUSE ,GROUP 3 ('/oracle/PRD/origlogA/log_g13m1.dbf',
    '/oracle/PRD/mirrlogA/log_g13m2.dbf') SIZE 50M  REUSE ,GROUP 4 ('/oracle/PRD/origlogB/log_g14m1.dbf',
    '/oracle/PRD/mirrlogB/log_g14m2.dbf') SIZE 50M  REUSEMon Nov 14 08:24:53 2011Database mounted in Exclusive Mode
    Mon Nov 14 08:25:06 2011Successful mount of redo thread 1, with mount id 1830841300
    Assigning activation ID 1830841300 (0x6d206bd4) Thread 1 opened at log sequence 1
    Current log# 1 seq# 1 mem# 0: /oracle/PRD/origlogA/log_g11m1.dbf
      Current log# 1 seq# 1 mem# 1: /oracle/PRD/mirrlogA/log_g11m2.dbf,m Successful open of redo thread 1
    Mon Nov 14 08:25:06 2011 MTTR advisory is disabled because FAST_START_MTTR_TARGET is not set
    Mon Nov 14 08:25:06 2011 SMON: enabling cache recovery
    Mon Nov 14 08:25:06 2011
    create tablespace SYSTEM datafile  '/oracle/PRD/sapdata1/system_1/system.data1' SIZE 350M REUSE AUTOEXTEND ON NEXT 20M MAXSIZE 10000M
      EXTENT MANAGEMENT LOCAL online
    Mon Nov 14 08:25:09 2011
    Incremental checkpoint up to RBA [0x1.3.0], current log tail at RBA [0x1.3.0]
    Mon Nov 14 08:25:15 2011
    Completed: create tablespace SYSTEM datafile  '/oracle/PRD/sapdata1/system_1/system.data1' SIZE 350M REUSE AUTOEXTEND ON NEXT 20M MAXSIZE 10000M
      EXTENT MANAGEMENT LOCAL online
    Mon Nov 14 08:25:15 2011
    create rollback segment SYSTEM tablespace SYSTEM
      storage (initial 50K next 50K)
    Completed: create rollback segment SYSTEM tablespace SYSTEM
      storage (initial 50K next 50K)
    Mon Nov 14 08:25:19 2011
    CREATE UNDO TABLESPACE PSAPUNDO DATAFILE  '/oracle/PRD/sapdata1/undo_1/undo.data1' SIZE 700M REUSE AUTOEXTEND ON NEXT 20M MAXSIZE 10000M
    Mon Nov 14 08:25:36 2011
    Successfully onlined Undo Tablespace 1.
    Completed: CREATE UNDO TABLESPACE PSAPUNDO DATAFILE  '/oracle/PRD/sapdata1/undo_1/undo.data1' SIZE 700M REUSE AUTOEXTEND ON NEXT 20M MAXSIZE 10000M
    Mon Nov 14 08:25:36 2011
    create tablespace SYSAUX datafile  '/oracle/PRD/sapdata1/sysaux_1/sysaux.data1' SIZE 200M REUSE AUTOEXTEND ON NEXT 20M MAXSIZE 10000M
      EXTENT MANAGEMENT LOCAL SEGMENT SPACE MANAGEMENT AUTO online
    Completed: create tablespace SYSAUX datafile  '/oracle/PRD/sapdata1/sysaux_1/sysaux.data1' SIZE 200M REUSE AUTOEXTEND ON NEXT 20M MAXSIZE 10000M
      EXTENT MANAGEMENT LOCAL SEGMENT SPACE MANAGEMENT AUTO online

  • The file name is not valid. The file name is a device or contains invalid characters.

    Hi ,
    I am getting below error in SSIS 2008 package when it is run through control-m
    The file name is not valid. The file name is a device or contains invalid characters.
    component "FF_SRC_InboundFidelityInputFile" (1) failed the pre-execute phase and returned error code 0xC020207E.
    although this package is working fine in dev environment from visual studio.
    control-m agent has proper permissions to the folder still it is failing. Please if anyone knows solution for this issue. I am working on this issue since more than a week but reached nowhere. Please help.
    Thanks 
    Paras Gupta

    Hi Paras,
    Based on your description, it is not the VS IDE issue, if it is related to the SSIS, I suggest you post the issue in this forum here:http://social.msdn.microsoft.com/Forums/sqlserver/en-US/home?forum=sqlintegrationservices
    , and there you would get better response.
    Best Regards,
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

Maybe you are looking for