Error in simulation: Not enough nodes found

Hello i am trying to simulate a simple active filter ckt using MAX9618. However, i keep getting error as Not enough nodes in my schematic I have attached the schematic for reference.
Can anyone please help me understand why am i getting this error?
If I remove U2B component in the schematic, i observed that I don't get the above mentioned error?
I am a complete newbie to multisim...
Now on LabVIEW 10.0 on Win7
Attachments:
Test_Schematic.ms11 ‏82 KB

Hi,
The way you created the op-amp section B is likely the problem. The model has 5 nodes while your section B symbol only has 3 pins. Refer to the following tutorial, to learn how to create multi-section part with different symbols:
http://www.ni.com/tutorial/14438/en/
Tien P.
National Instruments

Similar Messages

Not Enough Nodes Found netlist error

I am working on a project for a voltage multiplier/divider and am working off this schematic from texas instruments (I have attached a pdf of it). When I try to simulate the circuit, I get an netlist error on every LM101AD Opamp saying Not Enough Nodes Found and the circuit doesnt work as it is support to. I have attached the circuit in multisim and the original drawing. Thanks for your help, -Alex
Attachments:
Voltage Multiplier Divider.ms10 ‏264 KB
Voltage Divider Multiplier.pdf ‏33 KB

The reason for the error message is that there are more nodes on the opamp's model than are mapped to those nodes. This component has multiple models, and this is a problem in the database only with the default Linear Technology/LM101A model.
You can select the model in the Place a Component dialog when you place or replace a component (look for Model manuf./ID).
I've made these.changes to your file. It will now simulate without errors, but the rated capacitor blows up. I haven't looked in detail if this is what to expect (electronics is not my forte).
I've also added this to our defect tracker so we can resolve this in a future release and improve the error message.
Garret
Senior Software Developer
National Instruments
Circuit Design Community and Blog
If someone helped you, let them know. Mark as solved or give a kudo.
Attachments:
Voltage Multiplier Divider.ms10 ‏266 KB

Not enough nodes found

I'm going to simulate a SPN1N60C3 MOSFET from Infineon (Level1-model).
I've got a Spice Netlist Error for the MOSFET saying "Not enough nodes found".
Is there somebody who can tell me what does it mean in order to find out the reason for that error?
Thanks

Thanks Kittmaster,
here are the models:
CoolMos_standard_PSpice.lib is the original Spice-Lib from Infineon,
spn01n60c3_l1.cir conrtain the models I extracted and imported as one model in Multisim
Attachments:
spn01n60c3_l1.cir ‏5 KB

LM2902 "not enough nodes" error

I'm using Multisim 11.0.278.
I designed an EQ circuit that includes the model LM2902N. The first time I tried to simulate it, the netlist generator complained that the model should have a node called "VS-", but the netgen couldn't find it because it's actually called "GND".
I renamed the GND pins VS- and saved the corrected model in my User component library. Then I replaced the old LM2902s with the new one.
Now, when I try to simulate, I get a different error saying "not enough nodes found" in the LM2902.
How do I fix this?
The schematic in question is attached.
Attachments:
EQ.ms11 ‏262 KB

replacing the LM2902N components in your circuit with the equivalent in the database gave me no netlist issues and solved any that were in your circuit.
The likely cause of your current issue is the model mapping. If the model nodes are not properly mapped within the model tab of the component, you will get the not enough nodes error.
This can be fixed by going to.
1) Tools > Database > Database Manager
2) Locate you component in the components tab and select "Edit" (the component needs to be in your user or corporate database)
3) Once in the model tab of the component editor, ensure the table is shown.
If there are any pins showing NC, that is likely the cause of the not enough nodes found error. You will need to add the mapping for the NC node.(the order depends on the model in use and is usually written at the top of the model)

SSRS 2008 Column Chart with Calculated Series (moving average) "formula error - there are not enough data points for the period" error

I have a simple column chart grouping on 1 value on the category axis. For simplicity's sake, we are plotting $ amounts grouping by Month on the category axis. I right click on the data series and choose "Add calculated series...". I choose moving average. I want to move the average over at least 2 periods.
When I run the report, I get the error "Formula error - there are not enough data points for the period". The way the report is, I never have a guaranteed number of categories (there could be one or there could be 5). When there is 2 or more, the chart renders fine, however, when there is only 1 value, instead of suppressing the moving average line, I get that error and the chart shows nothing.
I don't think this is entirely acceptable for our end users. At a minimum, I would think the moving average line would be suppressed instead of hiding the entire chart. Does anyone know of any workarounds or do I have to enter another ms. connect bug/design consideration.
Thank you,
Dan

I was having the same error while trying to plot a moving average across 7 days. The work around I found was rather simple.
If you right click your report in the solution explorer and select "View Code" it will give you the underlying XML of the report. Find the entry for the value of your calculated series and enter a formula to dynamically create your periods.
<ChartFormulaParameter Name="Period">
<Value>=IIf(Count(Fields!Calls.Value) >= 7 ,7, (Count(Fields!Calls.Value)))</Value>
</ChartFormulaParameter>
What I'm doing here is getting the row count of records returned in the chart. If the returned rows are greater than or equal to 7 (The amount of days I want the average) it will set the points to 7. If not, it will set the number to the amount of returned rows. So far this has worked great. I'm probably going to add more code to handle no records returned although in my case that shouldn't happen but, you never know.
A side note:
If you open the calculated series properties in the designer, you will notice the number of periods is set to "0". If you change this it will overwrite your custom formula in the XML.

SPICE Netlist error, element 'that4301:':Not enough terminals for device type 'Tranline'

Hi as anyone come across the following or a similar error and found a solution?
SPICE Netlist error, element 'that4301:':Not enough terminals for device type 'Tranline'
The element that4301 is a vca I imported a model for.

Here's the model for the VCA:-
*THAT4301 VCA MACROMODEL
*CONNECTIONS:
* Iin - Current Input
* | Ec+ - Positive Control Port
* | | Ec- - Negative Control Port
* | | | Sym - Symmetry Adjust Terminal
* | | | | Vcc - Positive Supply Voltage
* | | | | | Vee - Negative Supply Voltage
* | | | | | | Iout - Current Output
* | | | | | | | GND
* | | | | | | | |
.SUBCKT 4301VCA_THAT P17 P15 P16 P14 P11 P10 P13 P9
J1 3 P17 1 FET 4
J2 4 P9 2 FET 4
CIN P17 P10 50pF
RS1 1 7 2.4K
RS2 2 7 2.4K
I1 P11 7 120uA
C2 3 4 20pF
RD1 3 P10 1K
RD2 4 P10 1K
GA P11 8 4 3 .001
RC1 8 0 12.6MEG
CC 8 5 55pF
RC2 5 P10 3K
EA P11 9 8 0 1
RA 9 10 820
CZ 9 10 300pF
Q1 10 10 11 QNPN
Q2 10 10 12 QNPN
RE1 11 13 1
RE2 12 14 0.9
Q3 P17 P15 13 QPNP
Q4 P13 P16 14 QPNP
Q5 P17 P16 15 QNPN
Q6 P13 P14 16 QNPN
RE3 15 17 1
RE4 16 18 0.9
Q7 19 19 17 QPNP
Q8 19 19 18 QPNP
COUT P13 0 35pF
I2 19 P10 6mA
IBIAS 0 6 30uA
Q9 6 6 20 QNPN
Q10 0 0 20 QPNP
EBIAS 10 19 6 0 2
.MODEL FET PJF(VTO=-1.46 BETA=1.67E-4 IS=10E-14)
.MODEL QNPN NPN(IS=6E-15 BF=250 VAF=95 CJE=7.5pF CJC=2.7pF)
.MODEL QPNP PNP(IS=4.7E-14 BF=125 VAF=50 CJE=20pF CJC=33pF)
.ENDS

Help Needed REP-1800 Formatter error VGS-1701 Not enough memory

Hi. Gents
Help needed
I’m working on a Report, it gets some 2 million records and the report pages are approximately 52,000
It works fine if the pages are lesser then 48,000 or the data is less let say one and half a million, the problem occurs only after 48000 + pages formatted.
Report is generated successfully when trying to go to the last page it throw an error.
REP-1800 Formatter error
VGS-1701 Not enough memory
I have already gone through the metalink DOC Id 95505.1 as well as OTN
But all in vain,
Any comments or help much appreciated.
Details are:
Reports 6i (Clients/Server) on Windows platform
(Windows XP Professional with SP 2)
Database: Oracle9i Enterprise Edition Release 9.2.0.5.0
Computer:
Pentium(R) 4, CPU 3.00GHz, 1 GB of RAM
Still 20 GB free space
Thanks & Regards

I don't see the point in making a report with more than 48,000 pages, I think Al Gore will not be happy when you start printing it...
The problem might be caused by the fact that Reports needs to format all output at once, and then even 1GB of memory will probably be not enough. Formatting all pages at once is needed if you use pagination with displaying total number of pages. If you have this, try to get that out of the report definition and try again.

When I try to import, I receive the following message: "An internal error has occurred: not enough memory". I always download my photos onto an external hard drive.

Yesterday,I downloaded an update for Lightroom 5. Now when I try to import, I receive the following message: "An internal error has occurred: not enough memory". The message comes up right after I click import, before I choose a file to upload.Here is the information I can think of that might be needed to answer this question:
- I always download my photos onto an external hard drive.It is about 10 % full.
- It says I have Lightroom 5.6 64 bit
- I am working from a newer laptop (Windows). The internal drive on the laptop has 289 gb and I am using 61 gb total memory.
- I have edited 2794 photos in Lightroom and it is all in one catalog.
- I did not have this problem until I made the update. I did have my first "bug" earlier this week when one of my photos had a line show up through the middle of it when I exported it. I was able to export it a second time without the line.
If there is more info. needed, let me know. I do photography as a hobby and know enough about Lightroom to edit out blemishes and adjust color balance, but not too much more, so forgive my ignorance if this is an obvious fix.
Sincerely,
Adrianne

Not Enough Memory typically refers to RAM. How much RAM do you have on your 64-bit OS computer? Do you have other programs running that may be using most of the memory?

What does "The project could not be prepared for publishing because an error occurred. (Not enough room in heap zone / )" mean?

When I click on finalize project in iMovie, an error message comes up that says "The project could not be prepared for publishing because an error occurred. (Not enough room in heap zone / )". How do I fix it, and what does it mean?

re-post in the iMovie forum where all the people that use that software are. This is the Lion 10.7 forum.

How can i fix this problem?? "The project could not be prepared for publishing because an error occurred. (Not enough room in heap zone / )"

The project could not be prepared for publishing because an error occurred. (Not enough room in heap zone / )
how can i fix this problem?

how can i fix this problem?
Go to the right forum.
This forum is for mobile iMovie.
you may need the iMovie Mac forum:
https://discussions.apple.com/community/ilife/imovie

The project could not be prepared for publishing because an error occurred. (Not enough room in heap zone / )

My iMovie Keep Saying "The project could not be prepared for publishing because an error occurred. (Not enough room in heap zone / )" How Can I Fix It?

Hi
Error -108 memFullErr Ran out of memory [not enough room in heap zone]
Turn off - TimeMachine usually works - re-try.
(the Application down in the Dock - not the Device)
But this can mean many thing's - My first thought is
• Free Space on Start-Up hard disk. How much ? (other disks do not count)
Yours Bengt W

Downloading itunes, I receive the error "there is not enough memory". How do I fix the memory issue?

When dowloadning tunes, I receive the error "there is not enough memory. I've deleted tunes from my library & ipod and I still get the error. How do I get around this?

It could be the newer version of iTunes requires more physical memory than your computer currently has available.
Do a right click on "My computer" and check out your computers memory/RAM specifications.
Windows XP is a bit bloated in the latest updates, trying to get people to upgrade to Windows 7, might be little room for other programs, especially one as huge as iTunes.
If you finally do choose a new machine, I have some tips:
For 3D gaming laptops, I wouldn't pick any graphics card scoring less than 1000 on this sites scale. Not scoring less than 2000 for towers.
http://www.videocardbenchmark.net/high_end_gpus.html
I would also choose a quad core processor scoring 5000 or better on this scale, 64 bit, Windows 7 Pro (so you can virtualize your XP programs) or OS X, and 4GB of RAM expandable to at least 8GB or future proofing your investment.
http://www.cpubenchmark.net/high_end_cpus.html
I would also choose 7,200 RPM hard drives for both towers and laptops for performance. On laptops while using the battery, set the energy savings to stop the hard drive spinning when not in use. Only choose the slower 5,400 RPM drive option if your always on battery and need maximum life as you lose about 20% with the faster drive, but gain 20% or more in performance.
Dual cores and 32 bit processors/OS with their 4GB RAM limit is soon to be old news.
For laptops, I highly recommend anti-glare displays for maximum use in any environment.

Error starting thread: Not enough storage is available to process...

Hi all,
We are seeing server going down frequently with below exception:
[ERROR][thread ] Failed to start new thread
[2010-04-08 14:36:54,046][ERROR][com.astrazeneca.portal.rss.ContentTransformer] - Error processing item:null
; SystemID: http://beaa.astrazeneca.net:10002/NewsBroker/resources/newsToRss.xsl; Line#: 21; Column#: 128
javax.xml.transform.TransformerException: java.lang.Error: Error starting thread: Not enough storage is available to process this command.
     at org.apache.xalan.extensions.ExtensionHandlerJavaPackage.callFunction(ExtensionHandlerJavaPackage.java:403)
     at org.apache.xalan.extensions.ExtensionHandlerJavaPackage.callFunction(ExtensionHandlerJavaPackage.java:426)
     at org.apache.xalan.extensions.ExtensionsTable.extFunction(ExtensionsTable.java:220)
     at org.apache.xalan.transformer.TransformerImpl.extFunction(TransformerImpl.java:437)
     at org.apache.xpath.functions.FuncExtFunction.execute(FuncExtFunction.java:199)
     at org.apache.xpath.XPath.execute(XPath.java:268)
     at org.apache.xalan.templates.ElemVariable.getValue(ElemVariable.java:279)
     at org.apache.xalan.templates.ElemVariable.execute(ElemVariable.java:247)
I have a weblogic support SR open and they suggested to add -XXtlaSize and -XXlargeObjectLimit to our JVM parameter. With these parameters, we are getting below error in Windows frequently:
Reporting queued error: faulting application java.exe, version 1.5.0.11, faulting module jvm.dll, version 27.3.1.1, fault address 0x0014b442.
I have seen few threads on Sun forum, but answer was not posted there. Details of our environment are as below:-
JVM : JROCKIT 1.5.0.11
OS : Windows 2003
Application Server : Weblogic 10
Any inputs or pointers will be highly appreciated as this is a bit urgent for me...
Thanks & Regards,
Sanjeev

Hi Henrik,
I am running Weblogic with below parameters now:
-Xnohup -Xms:1536m -Xmx:1536m -XXtlaSize:min=32k,preferred=768k -XXlargeObjectLimit:32K
Weblogic crashed again with below dump:
===== BEGIN DUMP =============================================================
JRockit dump produced after 0 days, 07:17:18 on Fri May 07 15:26:16 2010
Additional information is available in:
E:\PortalLIVDomaina\jrockit.5772.dump
E:\PortalLIVDomaina\jrockit.5772.mdmp
If you see this dump, please open a support case with BEA and
supply as much information as you can on your system setup and
the program you were running. You can also search for solutions
to your problem at http://forums.bea.com in
the forum jrockit.developer.interest.general.
Error Message: Illegal memory access. [54]
Exception Rec: EXCEPTION_ACCESS_VIOLATION (c0000005) at 0x005148AF - memory at 0x00000000 could not be written.
Minidump : Wrote mdmp. Size is 1406MB
SafeDllMode : -1
Version : BEA JRockit(R) R27.3.1-1_CR344434-89345-1.5.0_11-20070925-1628-windows-ia32
GC Strategy : Mode: throughput. Currently using strategy: genparpar
GC Status : OC currently running, in phase: sweeping. This is OC#3000.
: YC is not running. Last finished YC was YC#9937.
OC History : Strategy genparpar was used for OC#1.
: Strategy singleparpar was used for OC#2.
: Strategy genparpar was used for OC#3 to OC#3000.
YC History : Ran 11 YCs before OC#2996.
: Ran 18 YCs before OC#2997.
: Ran 11 YCs before OC#2998.
: Ran 8 YCs before OC#2999.
: Ran 1 YCs before OC#3000.
Heap : 0x00900000 - 0x60900000
Compaction : 0x06900000 - 0x0C900000
Could you please provide some input on this?
Thanks,
Sanjeev

Why doesn't my program open? Error message states "not enough RAM" but I have 5 GB avail

I have Elements 2.0. Have been using it on 3 computers. Suddenly this laptop won't even open the program. Error message states "not enough RAM" but I have 5 GB available. How can I fix this. No problem on other computers with same Windows 7, Elements 2.0. This laptop is an HP. Others are Toshiba & Dell.

globejr wrote:
I have Elements 2.0. Have been using it on 3 computers. Suddenly this laptop won't even open the program. Error message states "not enough RAM" but I have 5 GB available. How can I fix this. No problem on other computers with same Windows 7, Elements 2.0. This laptop is an HP. Others are Toshiba & Dell.
Even if you have 5GB of RAM, PSE can't make use of all of it because it is likely to be a 32 bit program (if not 16 bit). PSE2 is very old made for Windows 2000 or Windows 98 but this was all before my time so my facts must be wrong here.
I am amazed that you managed to install it on Windows 7 in the first place.
You might want to try this link:
<http://windows.microsoft.com/en-us/windows7/install-and-use-windows-xp-mode-in-windows-7>

My brand new MBP 13"got the error "there is not enough memory or disk space to convert this document". What gives? Help please!

I am trying to use mail merge in Word for Mac on My brand new MBP 13". And I get the error "there is not enough memory or disk space to convert this document". What gives? Help please!

Why do I get there is not enough memory...: Apple Support Communities
Error message in MS Word opening a .docx file "There is not enough - Microsoft Community

Error in simulation: Not enough nodes found

Similar Messages

Maybe you are looking for