SPICE Netlist error, element 'that4301:':Not enough terminals for device type 'Tranline'

Hi as anyone come across the following or a similar error and found a solution?
SPICE Netlist error, element 'that4301:':Not enough terminals for device type 'Tranline'
The element that4301 is a vca I imported a model for.

Here's the model for the VCA:-
*THAT4301 VCA MACROMODEL
*CONNECTIONS:
* Iin - Current Input
* | Ec+ - Positive Control Port
* | | Ec- - Negative Control Port
* | | | Sym - Symmetry Adjust Terminal
* | | | | Vcc - Positive Supply Voltage
* | | | | | Vee - Negative Supply Voltage
* | | | | | | Iout - Current Output
* | | | | | | | GND
* | | | | | | | |
.SUBCKT 4301VCA_THAT P17 P15 P16 P14 P11 P10 P13 P9
J1 3 P17 1 FET 4
J2 4 P9 2 FET 4
CIN P17 P10 50pF
RS1 1 7 2.4K
RS2 2 7 2.4K
I1 P11 7 120uA
C2 3 4 20pF
RD1 3 P10 1K
RD2 4 P10 1K
GA P11 8 4 3 .001
RC1 8 0 12.6MEG
CC 8 5 55pF
RC2 5 P10 3K
EA P11 9 8 0 1
RA 9 10 820
CZ 9 10 300pF
Q1 10 10 11 QNPN
Q2 10 10 12 QNPN
RE1 11 13 1
RE2 12 14 0.9
Q3 P17 P15 13 QPNP
Q4 P13 P16 14 QPNP
Q5 P17 P16 15 QNPN
Q6 P13 P14 16 QNPN
RE3 15 17 1
RE4 16 18 0.9
Q7 19 19 17 QPNP
Q8 19 19 18 QPNP
COUT P13 0 35pF
I2 19 P10 6mA
IBIAS 0 6 30uA
Q9 6 6 20 QNPN
Q10 0 0 20 QPNP
EBIAS 10 19 6 0 2
.MODEL FET PJF(VTO=-1.46 BETA=1.67E-4 IS=10E-14)
.MODEL QNPN NPN(IS=6E-15 BF=250 VAF=95 CJE=7.5pF CJC=2.7pF)
.MODEL QPNP PNP(IS=4.7E-14 BF=125 VAF=50 CJE=20pF CJC=33pF)
.ENDS

Similar Messages

Error In MIGO "Could not determine recipients for message type ACPJMM"

Dear all,
At the time of transaction Goods Receipt(MIGO), I am getting the error message "Could not determine recipients for message type ACPJMM".
System Diagnosis is as below
An IDoc of message type ACPJMM was passed to the ALE layer, but the three receiver fields in the header record were not filled. In this case the ALE layer tries to determine the receivers from the entries in the distribution model. There are no entries available in the distribution model for the above message type
I have check the ALE Settings in we20 and we21
and have assigned the following message types under Logical syste Partner Type
Outbound
ACPJMM
MATMAS
MBGMCR
RSINFO
RSSEND
WHSORD
Inbound
ACPJMM
DEBMAS
FTDABA
FTDACO
FTDACU
INSPECTIONPLAN_CREATE
MATMAS
MBGMCR
RSRQST
WHSCON
I have also created and Assigned a Logical System to the client and have also created a RFC with the same name
I have checked all settings is SALE and they are Fine.
This is a single system
Please help this is really ugrent
Regards
Suhail John

Hi,
Goto table TRWCA (T Code SE30) and deselect all the checked entries.
This should solve your problem.
Regards,
Priyadarshi

Could not determine recipients for message type ACPJMM

Dear Experts,
while i am trying PGI getting error message " Could not determine recipients for message type ACPJMM'
Kindly let me know wt is the reason and where i should changes for getting clear?
Thanks in advance
ishikesh

Hi Ishikesh,
If you want to deactivate this goto SM30, enter the table TRWCA, deactivate the component
RWEX - Idoc Output, External Accounting.
this should solve your problem.
refer following links
[Message type ACPJMM;
[Message no. B1003""Could not determine recipients for message type ACPJMM"";
[MIGO and MIRO Problum;
Regards,
Karthik

Could not determine recipients for message type BUPA_INBOUND_MAIN_SAVE_M

We are upgrading CRM from 4.0 to 7.0
While synchronizing a business partner from CRM to ECC, the IDOC control Data section shows no information on the "Receiver Information" Section.It also provides error as "Could not determine recipients for message type BUPA_INBOUND_MAIN_SAVE_M" with error No 29, Outbound Error in ALE.
The Message Type (BUPA_INBOUND_MAIN_SAVE_M) and the Basic Type (BUPA_INBOUND_MAIN_SAVE_M03) was not used in the CRM 4.0 and not sure the reason it apprears now in the IDOC.
The relevant BDOC is not created/shown in transaction SMW01.
We have verified WE20,21, BD64 in ECC
Any advice is greatly appreciated.
Regards
Dhina

Hi,
Please check below note if it helpful to you in resolving the issue.
Note 1447734 - Enhancement of message type BUPA_INBOUND_MAIN_SAVE_M
Thanks,
George

SPICE Netlist Error: Unable to parse parameter name

The history so far (using MS11):
I tried to make a new component, i.e. the CNY70.
Therefore I needed the simulation model. So I designed a simple subckt that I tested, and ok, it works.
Subckt schematic exported a netlist, lines added: .SUBCKT <name> 1 2 3 4 and .ENDS
This .cir file used as Model for the new part I created.
And then....used this new part in a testschematic.....and the simulation is aborted:::
SPICE Netlist Error in schematic RefDes 'd1', element 'ud1': Unable to parse parameter name
SPICE Netlist Error in schematic RefDes 'd1', element '<unknown>': Due to errors, the component 'ud1' has been omitted from the simulation.
QUESTION: what did I do wrong / what am I missing in the Subckt file????
I looked in some modelfiles of opto-manuf. like Avago, and they all make use of V-controlled-I sources etcetera.
Capera
EWB/Multisim Educational Licence User since EWB9
Attachments:
CNY70 subcircuittest4.pdf ‏8 KB
CNY70 subcircuit.ms11 ‏50 KB
CNY70 parttest1.ms11 ‏40 KB

Hello Capera,
I understand that spending alot time and ending up with an error can be extremely frustrating.
I did some further testing and it seems like I get the same error even with an empty model.
It seems to not be purely linked to this model.
Which specific steps did you follow?
Kind Regards,
Thierry C - Applications Engineering Specialist Northern European Region - National Instruments
CLD, CTA
If someone helped you, let them know. Mark as solved and/or give a kudo.

Getting SPICE netlist error in schematic...: Invalid subckt definition '21' and '33' on user added component

In some design work I was doing I needed to use a vacuum tube type that is not available in Multisim.
After some research on how to add a component I tracked down a spice model of this part and used the component wizard to add it.
After adding it and putting it in a circuit it will simulate fine for a few moments then errors will occur and it will not allow me to restart the simulation there after.
Here is the spice model I'm using, and I've attached a screen cap of the error messages. Any help fixing the errors would be appreciated.
* Filename: SV6AS7.inc V1 25/8/97
* Simulator: PSpice
* Device type: Power triode
* Device model: Svetlana 6AS7
* Author: Duncan Munro
* Date: 25/8/97
* Copyright: (C)1997-2000 Duncan Amplification
* The following parameters are not modelled:
* (1) Heater is not modelled.
* (2) Grid current is not modelled.
* Please note that this model is provided "as is" and
* no warranty is provided in respect of its suitability
* for any application.
* This model is provided for educational and non-profit use.
* Email queries to [email protected]
* Pins A Anode
* G Grid
* K Cathode
.SUBCKT 6AS7 A G K
* Calculate reduction in mu at large negative
* grid voltages
Emu mu 0 VALUE={PWRS(V(G,K),0.88)}
* Emission reduction due to low Va
Eel el 0 VALUE={ATAN(LIMIT(V(A,K),0,1E6)/10)}
* Calculate change in shape with reducing grid voltage
Eshape shape 0 VALUE={(220+V(G,K))/220}
Egs gs 0 VALUE={LIMIT(V(A,K)+V(mu)*2.8,0,1E6)}
Egs2 gs2 0 VALUE={PWRS(V(gs)*V(shape),1.5)*410E-6}
Ecath cc 0 VALUE={V(gs2)*V(el)}
* Calculate anode current
Ga A K VALUE={V(cc)}
* Capacitances
Cgk G K 8p
Cga A G 11p
Cak A K 3p
.ENDS

okay I guess the screen cap won't work. Here is the copy pasted error code I'm getting
------ Checking SPICE netlist for Reverse Futterman OTL 1.2 - Saturday, July 20, 2013, 2:36:07 PM ------
SPICE Netlist Error in schematic RefDes 'u2', element 'xu2_b': Invalid subckt definition name '33'
SPICE Netlist Error in schematic RefDes 'u2', element '': Due to errors, the subckt instance 'xu2_b' has been omitted from the simulation
SPICE Netlist Error in schematic RefDes 'u2', element 'xu2_a': Invalid subckt definition name '21'
SPICE Netlist Error in schematic RefDes 'u2', element '': Due to errors, the subckt instance 'xu2_a' has been omitted from the simulation
======= SPICE Netlist check completed, 4 error(s), 0 warning(s) =======
Error message from simulation: doAnalyses: Timestep too small
Error message from simulation: tran simulation(s) canceled

Why doesn't my program open? Error message states "not enough RAM" but I have 5 GB avail

I have Elements 2.0. Have been using it on 3 computers. Suddenly this laptop won't even open the program. Error message states "not enough RAM" but I have 5 GB available. How can I fix this. No problem on other computers with same Windows 7, Elements 2.0. This laptop is an HP. Others are Toshiba & Dell.

globejr wrote:
I have Elements 2.0. Have been using it on 3 computers. Suddenly this laptop won't even open the program. Error message states "not enough RAM" but I have 5 GB available. How can I fix this. No problem on other computers with same Windows 7, Elements 2.0. This laptop is an HP. Others are Toshiba & Dell.
Even if you have 5GB of RAM, PSE can't make use of all of it because it is likely to be a 32 bit program (if not 16 bit). PSE2 is very old made for Windows 2000 or Windows 98 but this was all before my time so my facts must be wrong here.
I am amazed that you managed to install it on Windows 7 in the first place.
You might want to try this link:
<http://windows.microsoft.com/en-us/windows7/install-and-use-windows-xp-mode-in-windows-7>

SPICE netlist error in schematic

I get the following error messages when I run the simulation.
Error: SPICE Netlist Error in schematic RefDes '', element '_uc2fffffffe*************': Unsupported component prefix type '_'
Error: SPICE Netlist Error in schematic RefDes '', element '<unknown>': Due to errors, the component '_uc2fffffffe*************' has been omitted from the simulation
Error: SPICE Netlist Error in schematic RefDes 'u1', element 'e_u3_e7': Unknown controlled source table syntax in 'e_u3_e7:ad8336__vga__1'
Error: SPICE Netlist Error in schematic RefDes 'u1', element 'ad8336__vga__1': Due to errors, the component 'e_u3_e7' has been omitted from the simulation
This just a test ckt for AD8336 chip.
thank you
Attachments:
AD8336test.ms11 ‏91 KB
ad8336.txt ‏11 KB

hey there
im also experiencing the same problem. please help
------ Checking SPICE netlist for TRT - 20 March 2012, 12:09:02 PM ------ SPICE Netlist Error in schematic RefDes 'u5', element 'xu5': Invalid subckt definition name '21' SPICE Netlist Error in schematic RefDes 'u5', element '<unknown>': Due to errors, the subckt instance 'xu5' has been omitted from the simulation SPICE Netlist Error in schematic RefDes 'u4', element 'xu4': Invalid subckt definition name '23' SPICE Netlist Error in schematic RefDes 'u4', element '<unknown>': Due to errors, the subckt instance 'xu4' has been omitted from the simulation SPICE Netlist Error in schematic RefDes 'u3', element 'xu3': Invalid subckt definition name '25' SPICE Netlist Error in schematic RefDes 'u3', element '<unknown>': Due to errors, the subckt instance 'xu3' has been omitted from the simulation SPICE Netlist Error in schematic RefDes 'u2', element 'xu2': Invalid subckt definition name 'u2_open_y' SPICE Netlist Error in schematic RefDes 'u2', element '<unknown>': Due to errors, the subckt instance 'xu2' has been omitted from the simulation SPICE Netlist Error in schematic RefDes 'u1', element 'xu1': Invalid subckt definition name 'u1_open_rb7backslashkbi3backslashpgd' SPICE Netlist Error in schematic RefDes 'u1', element '<unknown>': Due to errors, the subckt instance 'xu1' has been omitted from the simulation SPICE Netlist Error in schematic RefDes 'u6', element 'tu6': Unable to parse parameter name ======= SPICE Netlist check completed, 11 error(s), 0 warning(s) ======= Error message from simulation: tu6: transmission line z0 must be given Error message from simulation: doAnalyses: No such parameter on this device Error message from simulation: tran simulation(s) canceled
O.P Lekgotle

SSRS 2008 Column Chart with Calculated Series (moving average) "formula error - there are not enough data points for the period" error

I have a simple column chart grouping on 1 value on the category axis. For simplicity's sake, we are plotting $ amounts grouping by Month on the category axis. I right click on the data series and choose "Add calculated series...". I choose moving average. I want to move the average over at least 2 periods.
When I run the report, I get the error "Formula error - there are not enough data points for the period". The way the report is, I never have a guaranteed number of categories (there could be one or there could be 5). When there is 2 or more, the chart renders fine, however, when there is only 1 value, instead of suppressing the moving average line, I get that error and the chart shows nothing.
I don't think this is entirely acceptable for our end users. At a minimum, I would think the moving average line would be suppressed instead of hiding the entire chart. Does anyone know of any workarounds or do I have to enter another ms. connect bug/design consideration.
Thank you,
Dan

I was having the same error while trying to plot a moving average across 7 days. The work around I found was rather simple.
If you right click your report in the solution explorer and select "View Code" it will give you the underlying XML of the report. Find the entry for the value of your calculated series and enter a formula to dynamically create your periods.
<ChartFormulaParameter Name="Period">
<Value>=IIf(Count(Fields!Calls.Value) >= 7 ,7, (Count(Fields!Calls.Value)))</Value>
</ChartFormulaParameter>
What I'm doing here is getting the row count of records returned in the chart. If the returned rows are greater than or equal to 7 (The amount of days I want the average) it will set the points to 7. If not, it will set the number to the amount of returned rows. So far this has worked great. I'm probably going to add more code to handle no records returned although in my case that shouldn't happen but, you never know.
A side note:
If you open the calculated series properties in the designer, you will notice the number of periods is set to "0". If you change this it will overwrite your custom formula in the XML.

Help Needed REP-1800 Formatter error VGS-1701 Not enough memory

Hi. Gents
Help needed
I’m working on a Report, it gets some 2 million records and the report pages are approximately 52,000
It works fine if the pages are lesser then 48,000 or the data is less let say one and half a million, the problem occurs only after 48000 + pages formatted.
Report is generated successfully when trying to go to the last page it throw an error.
REP-1800 Formatter error
VGS-1701 Not enough memory
I have already gone through the metalink DOC Id 95505.1 as well as OTN
But all in vain,
Any comments or help much appreciated.
Details are:
Reports 6i (Clients/Server) on Windows platform
(Windows XP Professional with SP 2)
Database: Oracle9i Enterprise Edition Release 9.2.0.5.0
Computer:
Pentium(R) 4, CPU 3.00GHz, 1 GB of RAM
Still 20 GB free space
Thanks & Regards

I don't see the point in making a report with more than 48,000 pages, I think Al Gore will not be happy when you start printing it...
The problem might be caused by the fact that Reports needs to format all output at once, and then even 1GB of memory will probably be not enough. Formatting all pages at once is needed if you use pagination with displaying total number of pages. If you have this, try to get that out of the report definition and try again.

When I try to import, I receive the following message: "An internal error has occurred: not enough memory". I always download my photos onto an external hard drive.

Yesterday,I downloaded an update for Lightroom 5. Now when I try to import, I receive the following message: "An internal error has occurred: not enough memory". The message comes up right after I click import, before I choose a file to upload.Here is the information I can think of that might be needed to answer this question:
- I always download my photos onto an external hard drive.It is about 10 % full.
- It says I have Lightroom 5.6 64 bit
- I am working from a newer laptop (Windows). The internal drive on the laptop has 289 gb and I am using 61 gb total memory.
- I have edited 2794 photos in Lightroom and it is all in one catalog.
- I did not have this problem until I made the update. I did have my first "bug" earlier this week when one of my photos had a line show up through the middle of it when I exported it. I was able to export it a second time without the line.
If there is more info. needed, let me know. I do photography as a hobby and know enough about Lightroom to edit out blemishes and adjust color balance, but not too much more, so forgive my ignorance if this is an obvious fix.
Sincerely,
Adrianne

Not Enough Memory typically refers to RAM. How much RAM do you have on your 64-bit OS computer? Do you have other programs running that may be using most of the memory?

Getting " Not enough memory for the operation error " in BOE

Hi,
We are using BOE 11.0.
we try to schedule a new report with multiple database logins for testing in BOE. When we run the report we are getting error like "Not enough memory for the operation error"
The same report has been executed successfully when we run using Crystal reports developer. The report is fectching less than 10K records from all the databases together.
Please let me know which is causing the issue and also let me know is there any limit in the number of databases connecting for a single report.
many thanks in advance for all your help.
Cheers,
Suri ;-)

Hi Sarthan,
Sorry. I'm new to BOE. We know only scheduling the reports creating folders etc. :-)
I've seen one parameter "Maximum Cache Size Allowed (KBytes)" and the value for this parameter is 5000.
If we change it to a big number whether we can solve the issue ? Please suggest.
Cheers,
Suri ;-)

Not enough memory for Data Provider-Error while creating Data Source

Hi,
I am loading data into Master Data_Attribute InfoObject I am getting following error message while creating Data Source under "Proposal" Tab
"Not enough memory for Data Provider"
My Master Data InfoObject having 65 attributes
My CSV file having 15,00000 records
I am using BI 7.0 version
If anybody faced this problem. Please share with me
Thanks.

Hi
Here the problem with the space so plz contact ur BASIS people to increase the spae for particular object.

Error:The grouping element could not be determined for project

Hi,
When I am trying to issue goods for a project,I am getting the following error
"The grouping element could not be determined for project 1., plant 2., and MRP group 3.."
what may be the reason for this reason.
Regards,
Raju

Hi,
You are using Automatic Requirement Grouping in your project and there is some issue with the Material Master,please check the Material Master Views.
Muzamil

What does "The project could not be prepared for publishing because an error occurred. (Not enough room in heap zone / )" mean?

When I click on finalize project in iMovie, an error message comes up that says "The project could not be prepared for publishing because an error occurred. (Not enough room in heap zone / )". How do I fix it, and what does it mean?

re-post in the iMovie forum where all the people that use that software are. This is the Lion 10.7 forum.

SPICE Netlist error, element 'that4301:':Not enough terminals for device type 'Tranline'

Similar Messages

Maybe you are looking for