Error registering a Cisco 2811 with a clustered CallManager 4.3
Hello, i'm having problems registering a Cisco 2811 Gateway with a VWIC2-1MFT-E1 interface card with Cisco CallManager 4.3.
The error displayed when debugging mgcp is the following:
//-1/xxxxxxxxxxxx/MGCP/mgcp_mp_get_not_entity(828):[lvl=2]
Invalid parameter (pkt 0x4708C5E8 pkt->mgcp_parm_lines 0x00000000)
I configured mgcp by the following:
mgcp
mgcp call-agent VOIPSVR1 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp restart-delay 300
mgcp package-capability rtp-package
no mgcp package-capability res-package
mgcp package-capability sst-package
no mgcp package-capability fxr-package
mgcp package-capability pre-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp validate call-agent source-ipaddr
mgcp rtp payload-type g726r16 static
mgcp profile default
dial-peer voice 100 pots
service mgcpapp
direct-inward-dial
port 0/0/0:15
Previously, the gateway downloaded xml config files from the Cisco CallManager without problems and, in addition, when trying to add a Route Group (in the CallManager) this Gateway does not appear
in the list of Available Devices although
I have added it through the Device->Gateway Menu.
Need some advice and help. Thank you in advance.
Hi Jose,
The Domain name issue is outlined nicely in this doc;
MGCP Gateway Registration Failure with Cisco CallManager
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00805a316c.shtml#prob
If the IP domain name is configured in Cisco IOS on the MGCP gateway, enter the Fully Qualified Domain Name (FQDN) in the Domain Name field.
In the example: test and cisco.com represent the hostname and domain name respectively. If the IP domain name is not configured in Cisco IOS on the MGCP gateway, enter only the hostname of the MGCP gateway in the Domain Name field.
You would enter test.cisco.com (in CCM)
Hope this helps!
Rob
Similar Messages
-
Cisco 2811 with NM-16A as Terminal server.
Hello,
I am currently looking for a Cisco terminal server solution to remotely access through console my private Cisco home lab. I am thinking of buying Cisco 2811 but I struggle to figure out the difference which ASYNC/SYNC MODULE to use. So, my question, is it possible to use NM-16A module with Cisco 2811 or HWIC-16A module must be used? And what is the difference between them?
I found on Cisco website that NM-16A is not supported on Cisco 2811, however some forums stated that it is possible.
http://www.cisco.com/en/US/docs/ios/interface/configuration/guide/ir_nm16as.html#wp1027188
Your help is deeply appreciated.
Thank you,
ArikAsync is what you need.
I run this senario several places;
NAME: "chassis", DESCR: "2801 chassis"
PID: CISCO2801 ,
NAME: "WIC/VIC/HWIC 1", DESCR: "High Speed Wan Interface card with 16 RS232 async ports(HWIC-16A)"
PID: ,
NAME: "WIC/VIC/HWIC 3", DESCR: "9 Port FE Switch"
The HWIC is called HWIC-16A, but there is also a HWIC-8A
plus one or two CAB-HD8-ASYNC combo-squid-cables (green 1-to-8 with RJ45 plugs)
http://www.cisco.com/en/US/prod/collateral/modules/ps5949/ps6182/product_data_sheet0900aecd80274416.html
then you run rotary groups on the async SLIP's, via the cfg.
HTH
Martin -
Error registering DS-Series VM with OS disk on Premium Storage
Hi, are there any known issues in relation to backing up DS-series VMs that are created with an OS disk on premium storage? I've
tried testing with two different subscriptions and two different premium storage accounts and get an error when trying to register a DS-series VM which has an OS disk on a premium storage account.
ERROR DETAILS
Microsoft Azure Backup encountered an internal error.
Wait for a few minutes and then try the operation again. If the issue persists, contact Microsoft Support.
I've just created a DS-series VM on a standard storage account and registered it successfully. I haven't tried attaching a premium disk and backing
up yet however.Yes, VMs with disks on premium storage are not supported right now for Azure Backup. We will be updating our documentation shortly to reflect that limitation.
We will also update the forum when that support is available
Vikas Nahata -
How to enable IPS IPS/IDS in cisco 2811
Hi all,
I have a Cisco 2811 with IOS Version 12.4(20)T and I need to enable IPS or IDS in this. What is the config for this?
First of all, I need to know whether I can do IPS/IDS in my router as well..
- RibinHi,
I did enabled IPS in the router and configured to notify to our log server. Below is the log I received in my log server.
What does IPS does now and what kind of logs I can expect?
Thanks,
Ribin
Apr 19 14:53:38 192.168.11.10 4546: *Apr 19 09:27:41.254: %SYS-5-CONFIG_I: Configured from console by ribin on vty0 (192.168.11.35)
Apr 19 18:04:29 192.168.11.10 4548: *Apr 19 12:38:32.601: %CRYPTO-6-IPSEC_USING_DEFAULT: IPSec is using default transforms
Apr 19 18:12:10 192.168.11.10 4549: *Apr 19 12:46:14.541: %IPS-6-ENGINE_BUILDS_STARTED: 12:46:14 UTC Apr 19 2009
Apr 19 18:12:10 192.168.11.10 4550: *Apr 19 12:46:14.541: %IPS-6-ENGINE_BUILDING: atomic-ip - 3 signatures - 1 of 13 engines
Apr 19 18:12:10 192.168.11.10 4551: *Apr 19 12:46:14.557: %IPS-6-ENGINE_READY: atomic-ip - build time 16 ms - packets for this engine will be scanned
Apr 19 18:12:10 192.168.11.10 4552: *Apr 19 12:46:14.557: %IPS-6-ALL_ENGINE_BUILDS_COMPLETE: elapsed time 16 ms -
Hello to everyone,
I write because I have decided to pass from a cisco 2811 with ios 12.4/k9 to a cisco 1941 ios 15/k9, migrating configuration I have a problem with the ZBF.
I do not know if it's a problem of policy or differences between ios.
Could someone help me please?
Thank you all in advance
Regards,
Salvatore
Update: Configuration modified and IOS upgrade.Salvatore,
I don't know what problem exactly you face with your ZBF, but this may help you trbouleshooting your ZBF.
http://www.cisco.com/en/US/products/sw/secursw/ps1018/products_tech_note09186a0080a63b94.shtml
Thanks! -
ASA 5510 with Cisco 2811 Router Behind it - Not forwarding traffic
Hi all,
Some might know that I have been dealing with an issue where I cannot seem to get forwarded packets to reach their destinations behind an ASA 5510 that has a Cisco 2811 connected directly behind it.
Some examples that work.
I can SSH into the ASA.
I can SSH to the Cisco Routers behind the ASA.
I cannot reach items beind the Cisco Routers.
My Configuration is this (I am sure I included a bunch of info I didn't need to, but I am hoping it'll help!):
I have a static Ip assigned to my Ouside Interface Ethernet 0/1
It has an IP address of 199.195.xxx.xxx
I am trying to learn how to shape network traffic (this is all new to me) via the ASA and the Routers to specific devices.
The Inside Interface on the ASA is 10.10.1.1 255.255.255.252
The Outside Interface on the 2811 is 10.10.1.2 255.255.255.252
I can ping the router from the ASA. I can SSH through the ASA to the router.
BUT I CANNOT ACCESS DEVICES BEHIND THE ROUTER.
So, I wanted to BAM that statement above because I just don't kjnow where the issue is. Is the issue on the router or the ASA, my guess is, the router, but I just don't know.
Here are my configs, helpfully someone can help.
ASA errors on the ASDM when I try and hit resources; specifically a web device behind the ASA and the 2811. It's Ip address 192.168.1.5 it's listening on port 80.Static IP, not assigned via DHCP.
6
Feb 14 2014
19:38:56
98.22.121.x
41164
192.168.1.5
80
Built inbound TCP connection 1922859 for Outside:98.22.121.x/41164 (98.22.121.x/41164) to Inside:192.168.1.5/80 (199.195.168.x/8080)
6
Feb 14 2014
19:38:56
10.10.1.2
80
98.22.121.x
41164
Deny TCP (no connection) from 10.10.1.2/80 to 98.22.121.x/41164 flags SYN ACK on interface Inside
ASA5510# sh nat
Auto NAT Policies (Section 2)
1 (DMZ) to (Outside) source static ROUTER-2821 interface service tcp ssh 2222
translate_hits = 1, untranslate_hits = 18
2 (Inside) to (Outside) source static ROUTER-2811 interface service tcp ssh 222
translate_hits = 0, untranslate_hits = 13
3 (VOIP) to (Outside) source static ROUTER-3745 interface service tcp ssh 2223
translate_hits = 0, untranslate_hits = 3
4 (Inside) to (Outside) source static RDP-DC1 interface service tcp 3389 3389
translate_hits = 0, untranslate_hits = 236
5 (Inside) to (Outside) source static WEBCAM-01 interface service tcp www 8080
translate_hits = 0, untranslate_hits = 162
Manual NAT Policies (Section 3)
1 (any) to (Outside) source dynamic PAT-SOURCE interface
translate_hits = 1056862, untranslate_hits = 83506
ASA5510# show access-list
access-list cached ACL log flows: total 0, denied 0 (deny-flow-max 4096)
alert-interval 300
access-list USERS; 1 elements; name hash: 0x50681c1e
access-list USERS line 1 standard permit 10.10.1.0 255.255.255.0 (hitcnt=0) 0xdd6ba495
access-list Outside_access_in; 5 elements; name hash: 0xe796c137
access-list Outside_access_in line 1 extended permit tcp host 98.22.121.x object ROUTER-2811 eq ssh (hitcnt=37) 0x5a53778d
access-list Outside_access_in line 1 extended permit tcp host 98.22.121.x host 10.10.1.2 eq ssh (hitcnt=37) 0x5a53778d
access-list Outside_access_in line 2 extended permit tcp host 98.22.121.x object ROUTER-2821 eq ssh (hitcnt=8) 0x9f32bc21
access-list Outside_access_in line 2 extended permit tcp host 98.22.121.x host 10.10.0.2 eq ssh (hitcnt=8) 0x9f32bc21
access-list Outside_access_in line 3 extended permit tcp host 98.22.121.x interface Outside eq https (hitcnt=0) 0x385488b2
access-list Outside_access_in line 4 extended permit tcp host 98.22.121.x object WEBCAM-01 eq www (hitcnt=60) 0xe66674ec
access-list Outside_access_in line 4 extended permit tcp host 98.22.121.x host 192.168.1.5 eq www (hitcnt=60) 0xe66674ec
access-list Outside_access_in line 5 extended permit tcp host 98.22.121.x object RDP-DC1 eq 3389 (hitcnt=3) 0x02f13f4e
access-list Outside_access_in line 5 extended permit tcp host 98.22.121.x host 192.168.1.2 eq 3389 (hitcnt=3) 0x02f13f4e
access-list dmz-access-vlan1; 1 elements; name hash: 0xc3450860
access-list dmz-access-vlan1 line 1 extended permit ip 128.162.1.0 255.255.255.0 any (hitcnt=0) 0x429fedf1
access-list dmz-access; 3 elements; name hash: 0xf53f5801
access-list dmz-access line 1 remark Permit all traffic to DC1
access-list dmz-access line 2 extended permit ip 128.162.1.0 255.255.255.0 host 192.168.1.2 (hitcnt=0) 0xd2dced0a
access-list dmz-access line 3 remark Permit only DNS traffic to DNS server
access-list dmz-access line 4 extended permit udp 128.162.1.0 255.255.255.0 host 192.168.1.2 eq domain (hitcnt=0) 0xbb21093e
access-list dmz-access line 5 remark Permit ICMP to all devices in DC
access-list dmz-access line 6 extended permit icmp 128.162.1.0 255.255.255.0 192.168.1.0 255.255.255.0 (hitcnt=0) 0x71269ef7
CISCO-2811#show access-lists
Standard IP access list 1
10 permit any (1581021 matches)
CISCO-2811#show translate
CISCO-2811#show route
CISCO-2811#show route-map
CISCO-2811#show host
CISCO-2811#show hosts
Default domain is maladomini.int
Name/address lookup uses domain service
Name servers are 192.168.1.2, 199.195.168.4, 205.171.2.65, 205.171.3.65, 8.8.8.8
Codes: UN - unknown, EX - expired, OK - OK, ?? - revalidate
temp - temporary, perm - permanent
NA - Not Applicable None - Not defined
Host Port Flags Age Type Address(es)
api.mixpanel.com None (temp, OK) 2 IP 198.23.64.21
198.23.64.22
198.23.64.18
198.23.64.19
198.23.64.20
ASA5510:
ASA5510# sh run all
: Saved
ASA Version 9.1(4)
command-alias exec h help
command-alias exec lo logout
command-alias exec p ping
command-alias exec s show
terminal width 80
hostname ASA5510
domain-name maladomini.int
enable password x encrypted
no fips enable
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
xlate per-session permit tcp any4 any4
xlate per-session permit tcp any4 any6
xlate per-session permit tcp any6 any4
xlate per-session permit tcp any6 any6
xlate per-session permit udp any4 any4 eq domain
xlate per-session permit udp any4 any6 eq domain
xlate per-session permit udp any6 any4 eq domain
xlate per-session permit udp any6 any6 eq domain
passwd x encrypted
names
dns-guard
lacp system-priority 32768
interface Ethernet0/0
description LAN Interface
speed auto
duplex auto
no flowcontrol send on
nameif Inside
security-level 100
ip address 10.10.1.1 255.255.255.252
delay 10
interface Ethernet0/1
description WAN Interface
speed auto
duplex auto
no flowcontrol send on
nameif Outside
security-level 0
ip address 199.195.168.xxx 255.255.255.240
delay 10
interface Ethernet0/2
description DMZ
speed auto
duplex auto
no flowcontrol send on
nameif DMZ
security-level 100
ip address 10.10.0.1 255.255.255.252
delay 10
interface Ethernet0/3
description VOIP
speed auto
duplex auto
no flowcontrol send on
nameif VOIP
security-level 100
ip address 10.10.2.1 255.255.255.252
delay 10
interface Management0/0
speed auto
duplex auto
management-only
shutdown
nameif management
security-level 0
no ip address
delay 10
regex _default_gator "Gator"
regex _default_firethru-tunnel_2 "[/\\]cgi[-]bin[/\\]proxy"
regex _default_shoutcast-tunneling-protocol "1"
regex _default_http-tunnel "[/\\]HT_PortLog.aspx"
regex _default_x-kazaa-network "[\r\n\t ]+[xX]-[kK][aA][zZ][aA][aA]-[nN][eE][tT][wW][oO][rR][kK]"
regex _default_msn-messenger "[Aa][Pp][Pp][Ll][Ii][Cc][Aa][Tt][Ii][Oo][Nn][/\\][Xx][-][Mm][Ss][Nn][-][Mm][Ee][Ss][Ss][Ee][Nn][Gg][Ee][Rr]"
regex _default_GoToMyPC-tunnel_2 "[/\\]erc[/\\]Poll"
regex _default_gnu-http-tunnel_uri "[/\\]index[.]html"
regex _default_aim-messenger "[Hh][Tt][Tt][Pp][.][Pp][Rr][Oo][Xx][Yy][.][Ii][Cc][Qq][.][Cc][Oo][Mm]"
regex _default_gnu-http-tunnel_arg "crap"
regex _default_icy-metadata "[\r\n\t ]+[iI][cC][yY]-[mM][eE][tT][aA][dD][aA][tT][aA]"
regex _default_GoToMyPC-tunnel "machinekey"
regex _default_windows-media-player-tunnel "NSPlayer"
regex _default_yahoo-messenger "YMSG"
regex _default_httport-tunnel "photo[.]exectech[-]va[.]com"
regex _default_firethru-tunnel_1 "firethru[.]com"
checkheaps check-interval 60
checkheaps validate-checksum 60
boot system disk0:/asa914-k8.bin
ftp mode passive
clock timezone UTC 0
dns domain-lookup Outside
dns server-group DefaultDNS
name-server 199.195.168.4
name-server 205.171.2.65
name-server 205.171.3.65
domain-name maladomini.int
same-security-traffic permit inter-interface
object service ah pre-defined
service ah
description This is a pre-defined object
object service eigrp pre-defined
service eigrp
description This is a pre-defined object
object service esp pre-defined
service esp
description This is a pre-defined object
object service gre pre-defined
service gre
description This is a pre-defined object
object service icmp pre-defined
service icmp
description This is a pre-defined object
object service icmp6 pre-defined
service icmp6
description This is a pre-defined object
object service igmp pre-defined
service igmp
description This is a pre-defined object
object service igrp pre-defined
service igrp
description This is a pre-defined object
object service ip pre-defined
service ip
description This is a pre-defined object
object service ipinip pre-defined
service ipinip
description This is a pre-defined object
object service ipsec pre-defined
service esp
description This is a pre-defined object
object service nos pre-defined
service nos
description This is a pre-defined object
object service ospf pre-defined
service ospf
description This is a pre-defined object
object service pcp pre-defined
service pcp
description This is a pre-defined object
object service pim pre-defined
service pim
description This is a pre-defined object
object service pptp pre-defined
service gre
description This is a pre-defined object
object service snp pre-defined
service snp
description This is a pre-defined object
object service tcp pre-defined
service tcp
description This is a pre-defined object
object service udp pre-defined
service udp
description This is a pre-defined object
object service tcp-aol pre-defined
service tcp destination eq aol
description This is a pre-defined object
object service tcp-bgp pre-defined
service tcp destination eq bgp
description This is a pre-defined object
object service tcp-chargen pre-defined
service tcp destination eq chargen
description This is a pre-defined object
object service tcp-cifs pre-defined
service tcp destination eq cifs
description This is a pre-defined object
object service tcp-citrix-ica pre-defined
service tcp destination eq citrix-ica
description This is a pre-defined object
object service tcp-ctiqbe pre-defined
service tcp destination eq ctiqbe
description This is a pre-defined object
object service tcp-daytime pre-defined
service tcp destination eq daytime
description This is a pre-defined object
object service tcp-discard pre-defined
service tcp destination eq discard
description This is a pre-defined object
object service tcp-domain pre-defined
service tcp destination eq domain
description This is a pre-defined object
object service tcp-echo pre-defined
service tcp destination eq echo
description This is a pre-defined object
object service tcp-exec pre-defined
service tcp destination eq exec
description This is a pre-defined object
object service tcp-finger pre-defined
service tcp destination eq finger
description This is a pre-defined object
object service tcp-ftp pre-defined
service tcp destination eq ftp
description This is a pre-defined object
object service tcp-ftp-data pre-defined
service tcp destination eq ftp-data
description This is a pre-defined object
object service tcp-gopher pre-defined
service tcp destination eq gopher
description This is a pre-defined object
object service tcp-ident pre-defined
service tcp destination eq ident
description This is a pre-defined object
object service tcp-imap4 pre-defined
service tcp destination eq imap4
description This is a pre-defined object
object service tcp-irc pre-defined
service tcp destination eq irc
description This is a pre-defined object
object service tcp-hostname pre-defined
service tcp destination eq hostname
description This is a pre-defined object
object service tcp-kerberos pre-defined
service tcp destination eq kerberos
description This is a pre-defined object
object service tcp-klogin pre-defined
service tcp destination eq klogin
description This is a pre-defined object
object service tcp-kshell pre-defined
service tcp destination eq kshell
description This is a pre-defined object
object service tcp-ldap pre-defined
service tcp destination eq ldap
description This is a pre-defined object
object service tcp-ldaps pre-defined
service tcp destination eq ldaps
description This is a pre-defined object
object service tcp-login pre-defined
service tcp destination eq login
description This is a pre-defined object
object service tcp-lotusnotes pre-defined
service tcp destination eq lotusnotes
description This is a pre-defined object
object service tcp-nfs pre-defined
service tcp destination eq nfs
description This is a pre-defined object
object service tcp-netbios-ssn pre-defined
service tcp destination eq netbios-ssn
description This is a pre-defined object
object service tcp-whois pre-defined
service tcp destination eq whois
description This is a pre-defined object
object service tcp-nntp pre-defined
service tcp destination eq nntp
description This is a pre-defined object
object service tcp-pcanywhere-data pre-defined
service tcp destination eq pcanywhere-data
description This is a pre-defined object
object service tcp-pim-auto-rp pre-defined
service tcp destination eq pim-auto-rp
description This is a pre-defined object
object service tcp-pop2 pre-defined
service tcp destination eq pop2
description This is a pre-defined object
object service tcp-pop3 pre-defined
service tcp destination eq pop3
description This is a pre-defined object
object service tcp-pptp pre-defined
service tcp destination eq pptp
description This is a pre-defined object
object service tcp-lpd pre-defined
service tcp destination eq lpd
description This is a pre-defined object
object service tcp-rsh pre-defined
service tcp destination eq rsh
description This is a pre-defined object
object service tcp-rtsp pre-defined
service tcp destination eq rtsp
description This is a pre-defined object
object service tcp-sip pre-defined
service tcp destination eq sip
description This is a pre-defined object
object service tcp-smtp pre-defined
service tcp destination eq smtp
description This is a pre-defined object
object service tcp-ssh pre-defined
service tcp destination eq ssh
description This is a pre-defined object
object service tcp-sunrpc pre-defined
service tcp destination eq sunrpc
description This is a pre-defined object
object service tcp-tacacs pre-defined
service tcp destination eq tacacs
description This is a pre-defined object
object service tcp-talk pre-defined
service tcp destination eq talk
description This is a pre-defined object
object service tcp-telnet pre-defined
service tcp destination eq telnet
description This is a pre-defined object
object service tcp-uucp pre-defined
service tcp destination eq uucp
description This is a pre-defined object
object service tcp-www pre-defined
service tcp destination eq www
description This is a pre-defined object
object service tcp-http pre-defined
service tcp destination eq www
description This is a pre-defined object
object service tcp-https pre-defined
service tcp destination eq https
description This is a pre-defined object
object service tcp-cmd pre-defined
service tcp destination eq rsh
description This is a pre-defined object
object service tcp-sqlnet pre-defined
service tcp destination eq sqlnet
description This is a pre-defined object
object service tcp-h323 pre-defined
service tcp destination eq h323
description This is a pre-defined object
object service tcp-udp-cifs pre-defined
service tcp-udp destination eq cifs
description This is a pre-defined object
object service tcp-udp-discard pre-defined
service tcp-udp destination eq discard
description This is a pre-defined object
object service tcp-udp-domain pre-defined
service tcp-udp destination eq domain
description This is a pre-defined object
object service tcp-udp-echo pre-defined
service tcp-udp destination eq echo
description This is a pre-defined object
object service tcp-udp-kerberos pre-defined
service tcp-udp destination eq kerberos
description This is a pre-defined object
object service tcp-udp-nfs pre-defined
service tcp-udp destination eq nfs
description This is a pre-defined object
object service tcp-udp-pim-auto-rp pre-defined
service tcp-udp destination eq pim-auto-rp
description This is a pre-defined object
object service tcp-udp-sip pre-defined
service tcp-udp destination eq sip
description This is a pre-defined object
object service tcp-udp-sunrpc pre-defined
service tcp-udp destination eq sunrpc
description This is a pre-defined object
object service tcp-udp-tacacs pre-defined
service tcp-udp destination eq tacacs
description This is a pre-defined object
object service tcp-udp-www pre-defined
service tcp-udp destination eq www
description This is a pre-defined object
object service tcp-udp-http pre-defined
service tcp-udp destination eq www
description This is a pre-defined object
object service tcp-udp-talk pre-defined
service tcp-udp destination eq talk
description This is a pre-defined object
object service udp-biff pre-defined
service udp destination eq biff
description This is a pre-defined object
object service udp-bootpc pre-defined
service udp destination eq bootpc
description This is a pre-defined object
object service udp-bootps pre-defined
service udp destination eq bootps
description This is a pre-defined object
object service udp-cifs pre-defined
service udp destination eq cifs
description This is a pre-defined object
object service udp-discard pre-defined
service udp destination eq discard
description This is a pre-defined object
object service udp-domain pre-defined
service udp destination eq domain
description This is a pre-defined object
object service udp-dnsix pre-defined
service udp destination eq dnsix
description This is a pre-defined object
object service udp-echo pre-defined
service udp destination eq echo
description This is a pre-defined object
object service udp-www pre-defined
service udp destination eq www
description This is a pre-defined object
object service udp-http pre-defined
service udp destination eq www
description This is a pre-defined object
object service udp-nameserver pre-defined
service udp destination eq nameserver
description This is a pre-defined object
object service udp-kerberos pre-defined
service udp destination eq kerberos
description This is a pre-defined object
object service udp-mobile-ip pre-defined
service udp destination eq mobile-ip
description This is a pre-defined object
object service udp-nfs pre-defined
service udp destination eq nfs
description This is a pre-defined object
object service udp-netbios-ns pre-defined
service udp destination eq netbios-ns
description This is a pre-defined object
object service udp-netbios-dgm pre-defined
service udp destination eq netbios-dgm
description This is a pre-defined object
object service udp-ntp pre-defined
service udp destination eq ntp
description This is a pre-defined object
object service udp-pcanywhere-status pre-defined
service udp destination eq pcanywhere-status
description This is a pre-defined object
object service udp-pim-auto-rp pre-defined
service udp destination eq pim-auto-rp
description This is a pre-defined object
object service udp-radius pre-defined
service udp destination eq radius
description This is a pre-defined object
object service udp-radius-acct pre-defined
service udp destination eq radius-acct
description This is a pre-defined object
object service udp-rip pre-defined
service udp destination eq rip
description This is a pre-defined object
object service udp-secureid-udp pre-defined
service udp destination eq secureid-udp
description This is a pre-defined object
object service udp-sip pre-defined
service udp destination eq sip
description This is a pre-defined object
object service udp-snmp pre-defined
service udp destination eq snmp
description This is a pre-defined object
object service udp-snmptrap pre-defined
service udp destination eq snmptrap
description This is a pre-defined object
object service udp-sunrpc pre-defined
service udp destination eq sunrpc
description This is a pre-defined object
object service udp-syslog pre-defined
service udp destination eq syslog
description This is a pre-defined object
object service udp-tacacs pre-defined
service udp destination eq tacacs
description This is a pre-defined object
object service udp-talk pre-defined
service udp destination eq talk
description This is a pre-defined object
object service udp-tftp pre-defined
service udp destination eq tftp
description This is a pre-defined object
object service udp-time pre-defined
service udp destination eq time
description This is a pre-defined object
object service udp-who pre-defined
service udp destination eq who
description This is a pre-defined object
object service udp-xdmcp pre-defined
service udp destination eq xdmcp
description This is a pre-defined object
object service udp-isakmp pre-defined
service udp destination eq isakmp
description This is a pre-defined object
object service icmp6-unreachable pre-defined
service icmp6 unreachable
description This is a pre-defined object
object service icmp6-packet-too-big pre-defined
service icmp6 packet-too-big
description This is a pre-defined object
object service icmp6-time-exceeded pre-defined
service icmp6 time-exceeded
description This is a pre-defined object
object service icmp6-parameter-problem pre-defined
service icmp6 parameter-problem
description This is a pre-defined object
object service icmp6-echo pre-defined
service icmp6 echo
description This is a pre-defined object
object service icmp6-echo-reply pre-defined
service icmp6 echo-reply
description This is a pre-defined object
object service icmp6-membership-query pre-defined
service icmp6 membership-query
description This is a pre-defined object
object service icmp6-membership-report pre-defined
service icmp6 membership-report
description This is a pre-defined object
object service icmp6-membership-reduction pre-defined
service icmp6 membership-reduction
description This is a pre-defined object
object service icmp6-router-renumbering pre-defined
service icmp6 router-renumbering
description This is a pre-defined object
object service icmp6-router-solicitation pre-defined
service icmp6 router-solicitation
description This is a pre-defined object
object service icmp6-router-advertisement pre-defined
service icmp6 router-advertisement
description This is a pre-defined object
object service icmp6-neighbor-solicitation pre-defined
service icmp6 neighbor-solicitation
description This is a pre-defined object
object service icmp6-neighbor-advertisement pre-defined
service icmp6 neighbor-advertisement
description This is a pre-defined object
object service icmp6-neighbor-redirect pre-defined
service icmp6 neighbor-redirect
description This is a pre-defined object
object service icmp-echo pre-defined
service icmp echo
description This is a pre-defined object
object service icmp-echo-reply pre-defined
service icmp echo-reply
description This is a pre-defined object
object service icmp-unreachable pre-defined
service icmp unreachable
description This is a pre-defined object
object service icmp-source-quench pre-defined
service icmp source-quench
description This is a pre-defined object
object service icmp-redirect pre-defined
service icmp redirect
description This is a pre-defined object
object service icmp-alternate-address pre-defined
service icmp alternate-address
description This is a pre-defined object
object service icmp-router-advertisement pre-defined
service icmp router-advertisement
description This is a pre-defined object
object service icmp-router-solicitation pre-defined
service icmp router-solicitation
description This is a pre-defined object
object service icmp-time-exceeded pre-defined
service icmp time-exceeded
description This is a pre-defined object
object service icmp-parameter-problem pre-defined
service icmp parameter-problem
description This is a pre-defined object
object service icmp-timestamp-request pre-defined
service icmp timestamp-request
description This is a pre-defined object
object service icmp-timestamp-reply pre-defined
service icmp timestamp-reply
description This is a pre-defined object
object service icmp-information-request pre-defined
service icmp information-request
description This is a pre-defined object
object service icmp-information-reply pre-defined
service icmp information-reply
description This is a pre-defined object
object service icmp-mask-request pre-defined
service icmp mask-request
description This is a pre-defined object
object service icmp-mask-reply pre-defined
service icmp mask-reply
description This is a pre-defined object
object service icmp-traceroute pre-defined
service icmp traceroute
description This is a pre-defined object
object service icmp-conversion-error pre-defined
service icmp conversion-error
description This is a pre-defined object
object service icmp-mobile-redirect pre-defined
service icmp mobile-redirect
description This is a pre-defined object
object network ROUTER-2811
host 10.10.1.2
object network ROUTER-2821
host 10.10.0.2
object network WEBCAM-01
host 192.168.1.5
object network DNS-SERVER
host 192.168.1.2
object network ROUTER-3745
host 10.10.2.2
object network RDP-DC1
host 192.168.1.2
object-group network PAT-SOURCE
network-object 10.10.1.0 255.255.255.252
network-object 10.10.0.0 255.255.255.252
network-object 10.10.2.0 255.255.255.252
network-object 192.168.0.0 255.255.255.0
network-object 172.16.10.0 255.255.255.0
network-object 172.16.20.0 255.255.255.0
network-object 128.162.1.0 255.255.255.0
network-object 128.162.10.0 255.255.255.0
network-object 128.162.20.0 255.255.255.0
object-group network DM_INLINE_NETWORK_2
network-object host 98.22.121.x
object-group network Outside_access_in
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object gre
access-list USERS standard permit 10.10.1.0 255.255.255.0
access-list Outside_access_in extended permit tcp host 98.22.121.x object ROUTER-2811 eq ssh
access-list Outside_access_in extended permit tcp host 98.22.121.x object ROUTER-2821 eq ssh
access-list Outside_access_in extended permit tcp host 98.22.121.x interface Outside eq https
access-list Outside_access_in extended permit tcp host 98.22.121.x object WEBCAM-01 eq www
access-list Outside_access_in extended permit tcp host 98.22.121.x object RDP-DC1 eq 3389
access-list dmz-access-vlan1 extended permit ip 128.162.1.0 255.255.255.0 any
access-list dmz-access remark Permit all traffic to DC1
access-list dmz-access extended permit ip 128.162.1.0 255.255.255.0 host 192.168.1.2
access-list dmz-access remark Permit only DNS traffic to DNS server
access-list dmz-access extended permit udp 128.162.1.0 255.255.255.0 host 192.168.1.2 eq domain
access-list dmz-access remark Permit ICMP to all devices in DC
access-list dmz-access extended permit icmp 128.162.1.0 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
logging enable
logging buffer-size 4096
logging asdm-buffer-size 100
logging asdm informational
logging flash-minimum-free 3076
logging flash-maximum-allocation 1024
logging rate-limit 1 10 message 747001
logging rate-limit 1 1 message 402116
logging rate-limit 1 10 message 620002
logging rate-limit 1 10 message 717015
logging rate-limit 1 10 message 717018
logging rate-limit 1 10 message 201013
logging rate-limit 1 10 message 201012
logging rate-limit 1 1 message 313009
logging rate-limit 100 1 message 750003
logging rate-limit 100 1 message 750002
logging rate-limit 100 1 message 750004
logging rate-limit 1 10 message 419003
logging rate-limit 1 10 message 405002
logging rate-limit 1 10 message 405003
logging rate-limit 1 10 message 421007
logging rate-limit 1 10 message 405001
logging rate-limit 1 10 message 421001
logging rate-limit 1 10 message 421002
logging rate-limit 1 10 message 337004
logging rate-limit 1 10 message 337005
logging rate-limit 1 10 message 337001
logging rate-limit 1 10 message 337002
logging rate-limit 1 60 message 199020
logging rate-limit 1 10 message 337003
logging rate-limit 2 5 message 199011
logging rate-limit 1 10 message 199010
logging rate-limit 1 10 message 337009
logging rate-limit 2 5 message 199012
logging rate-limit 1 10 message 710002
logging rate-limit 1 10 message 209003
logging rate-limit 1 10 message 209004
logging rate-limit 1 10 message 209005
logging rate-limit 1 10 message 431002
logging rate-limit 1 10 message 431001
logging rate-limit 1 1 message 447001
logging rate-limit 1 10 message 110003
logging rate-limit 1 10 message 110002
logging rate-limit 1 10 message 429007
logging rate-limit 1 10 message 216004
logging rate-limit 1 10 message 450001
flow-export template timeout-rate 30
flow-export active refresh-interval 1
mtu Inside 1500
mtu Outside 1500
mtu management 1500
mtu DMZ 1500
mtu VOIP 1500
icmp unreachable rate-limit 1 burst-size 1
icmp deny any Outside
asdm image disk0:/asdm-715.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network ROUTER-2811
nat (Inside,Outside) static interface service tcp ssh 222
object network ROUTER-2821
nat (DMZ,Outside) static interface service tcp ssh 2222
object network WEBCAM-01
nat (Inside,Outside) static interface service tcp www 8080
object network ROUTER-3745
nat (VOIP,Outside) static interface service tcp ssh 2223
object network RDP-DC1
nat (Inside,Outside) static interface service tcp 3389 3389
nat (any,Outside) after-auto source dynamic PAT-SOURCE interface
access-group Outside_access_in in interface Outside
ipv6 dhcprelay timeout 60
router rip
network 10.0.0.0
version 2
no auto-summary
route Outside 0.0.0.0 0.0.0.0 199.195.168.113 1
route Inside 128.162.1.0 255.255.255.0 10.10.0.2 1
route Inside 128.162.10.0 255.255.255.0 10.10.0.2 1
route Inside 128.162.20.0 255.255.255.0 10.10.0.2 1
route Inside 172.16.10.0 255.255.255.0 10.10.1.2 1
route Inside 172.16.20.0 255.255.255.0 10.10.1.2 1
route Inside 192.168.1.0 255.255.255.0 10.10.1.2 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
action continue
no cts server-group
no cts sxp enable
no cts sxp default
no cts sxp default source-ip
cts sxp reconciliation period 120
cts sxp retry period 120
user-identity enable
user-identity domain LOCAL
user-identity default-domain LOCAL
user-identity action mac-address-mismatch remove-user-ip
user-identity inactive-user-timer minutes 60
user-identity poll-import-user-group-timer hours 8
user-identity ad-agent active-user-database full-download
user-identity ad-agent hello-timer seconds 30 retry-times 5
no user-identity user-not-found enable
aaa authentication ssh console LOCAL
http server enable 443
http 0.0.0.0 0.0.0.0 Inside
http 98.22.121.x 255.255.255.255 Outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
no snmp-server enable traps syslog
no snmp-server enable traps ipsec start stop
no snmp-server enable traps entity config-change fru-insert fru-remove fan-failure power-supply power-supply-presence cpu-temperature chassis-temperature power-supply-temperature chassis-fan-failure
no snmp-server enable traps memory-threshold
no snmp-server enable traps interface-threshold
no snmp-server enable traps remote-access session-threshold-exceeded
no snmp-server enable traps connection-limit-reached
no snmp-server enable traps cpu threshold rising
no snmp-server enable traps ikev2 start stop
no snmp-server enable traps nat packet-discard
snmp-server enable
snmp-server listen-port 161
fragment size 200 Inside
fragment chain 24 Inside
fragment timeout 5 Inside
no fragment reassembly full Inside
fragment size 200 Outside
fragment chain 24 Outside
fragment timeout 5 Outside
no fragment reassembly full Outside
fragment size 200 management
fragment chain 24 management
fragment timeout 5 management
no fragment reassembly full management
fragment size 200 DMZ
fragment chain 24 DMZ
fragment timeout 5 DMZ
no fragment reassembly full DMZ
fragment size 200 VOIP
fragment chain 24 VOIP
fragment timeout 5 VOIP
no fragment reassembly full VOIP
no sysopt connection timewait
sysopt connection tcpmss 1380
sysopt connection tcpmss minimum 0
sysopt connection permit-vpn
sysopt connection reclassify-vpn
no sysopt connection preserve-vpn-flows
no sysopt radius ignore-secret
no sysopt noproxyarp Inside
no sysopt noproxyarp Outside
no sysopt noproxyarp management
no sysopt noproxyarp DMZ
no sysopt noproxyarp VOIP
service password-recovery
no crypto ipsec ikev2 sa-strength-enforcement
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto ipsec security-association replay window-size 64
crypto ipsec security-association pmtu-aging infinite
crypto ipsec fragmentation before-encryption Inside
crypto ipsec fragmentation before-encryption Outside
crypto ipsec fragmentation before-encryption management
crypto ipsec fragmentation before-encryption DMZ
crypto ipsec fragmentation before-encryption VOIP
crypto ipsec df-bit copy-df Inside
crypto ipsec df-bit copy-df Outside
crypto ipsec df-bit copy-df management
crypto ipsec df-bit copy-df DMZ
crypto ipsec df-bit copy-df VOIP
crypto ca trustpool policy
revocation-check none
crl cache-time 60
crl enforcenextupdate
crypto isakmp identity auto
crypto isakmp nat-traversal 20
crypto ikev2 cookie-challenge 50
crypto ikev2 limit max-in-negotiation-sa 100
no crypto ikev2 limit max-sa
crypto ikev2 redirect during-auth
crypto ikev1 limit max-in-negotiation-sa 20
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 Inside
ssh 98.22.121.x 255.255.255.255 Outside
ssh timeout 60
ssh version 2
ssh key-exchange group dh-group1-sha1
console timeout 0
vpn-addr-assign aaa
vpn-addr-assign dhcp
vpn-addr-assign local reuse-delay 0
ipv6-vpn-addr-assign aaa
ipv6-vpn-addr-assign local reuse-delay 0
no vpn-sessiondb max-other-vpn-limit
no vpn-sessiondb max-anyconnect-premium-or-essentials-limit
no remote-access threshold
l2tp tunnel hello 60
tls-proxy maximum-session 100
threat-detection rate dos-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate dos-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate bad-packet-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate bad-packet-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate acl-drop rate-interval 600 average-rate 400 burst-rate 800
threat-detection rate acl-drop rate-interval 3600 average-rate 320 burst-rate 640
threat-detection rate conn-limit-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate conn-limit-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate icmp-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate icmp-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate scanning-threat rate-interval 600 average-rate 5 burst-rate 10
threat-detection rate scanning-threat rate-interval 3600 average-rate 4 burst-rate 8
threat-detection rate syn-attack rate-interval 600 average-rate 100 burst-rate 200
threat-detection rate syn-attack rate-interval 3600 average-rate 80 burst-rate 160
threat-detection rate fw-drop rate-interval 600 average-rate 400 burst-rate 1600
threat-detection rate fw-drop rate-interval 3600 average-rate 320 burst-rate 1280
threat-detection rate inspect-drop rate-interval 600 average-rate 400 burst-rate 1600
threat-detection rate inspect-drop rate-interval 3600 average-rate 320 burst-rate 1280
threat-detection rate interface-drop rate-interval 600 average-rate 2000 burst-rate 8000
threat-detection rate interface-drop rate-interval 3600 average-rate 1600 burst-rate 6400
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 24.56.178.140 source Outside prefer
ssl server-version any
ssl client-version any
ssl encryption rc4-sha1 dhe-aes128-sha1 dhe-aes256-sha1 aes128-sha1 aes256-sha1 3des-sha1
ssl certificate-authentication fca-timeout 2
webvpn
memory-size percent 50
port 443
dtls port 443
character-encoding none
no http-proxy
no https-proxy
default-idle-timeout 1800
portal-access-rule none
no csd enable
no anyconnect enable
no tunnel-group-list enable
no tunnel-group-preference group-url
rewrite order 65535 enable resource-mask *
no internal-password
no onscreen-keyboard
no default-language
no smart-tunnel notification-icon
no keepout
cache
no disable
max-object-size 1000
min-object-size 0
no cache-static-content enable
lmfactor 20
expiry-time 1
no auto-signon
no error-recovery disable
no ssl-server-check
no mus password
mus host mus.cisco.com
no hostscan data-limit
: # show import webvpn customization
: Template
: DfltCustomization
: # show import webvpn url-list
: Template
: # show import webvpn translation-table
: Translation Tables' Templates:
: PortForwarder
: banners
: customization
: url-list
: webvpn
: Translation Tables:
: fr PortForwarder
: fr customization
: fr webvpn
: ja PortForwarder
: ja customization
: ja webvpn
: ru PortForwarder
: ru customization
: ru webvpn
: # show import webvpn mst-translation
: No MS translation tables defined
: # show import webvpn webcontent
: No custom webcontent is loaded
: # show import webvpn AnyConnect-customization
: No OEM resources defined
: # show import webvpn plug-in
group-policy DfltGrpPolicy internal
group-policy DfltGrpPolicy attributes
banner none
wins-server none
dns-server none
dhcp-network-scope none
vpn-access-hours none
vpn-simultaneous-logins 3
vpn-idle-timeout 30
vpn-idle-timeout alert-interval 1
vpn-session-timeout none
vpn-session-timeout alert-interval 1
vpn-filter none
ipv6-vpn-filter none
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec ssl-clientless
password-storage disable
ip-comp disable
re-xauth disable
group-lock none
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelall
ipv6-split-tunnel-policy tunnelall
split-tunnel-network-list none
default-domain none
split-dns none
split-tunnel-all-dns disable
intercept-dhcp 255.255.255.255 disable
secure-unit-authentication disable
user-authentication disable
user-authentication-idle-timeout 30
ip-phone-bypass disable
client-bypass-protocol disable
gateway-fqdn none
leap-bypass disable
nem disable
backup-servers keep-client-config
msie-proxy server none
msie-proxy method no-modify
msie-proxy except-list none
msie-proxy local-bypass disable
msie-proxy pac-url none
msie-proxy lockdown enable
vlan none
nac-settings none
address-pools none
ipv6-address-pools none
smartcard-removal-disconnect enable
scep-forwarding-url none
client-firewall none
client-access-rule none
webvpn
url-list none
filter none
homepage none
html-content-filter none
port-forward name Application Access
port-forward disable
http-proxy disable
sso-server none
anyconnect ssl dtls enable
anyconnect mtu 1406
anyconnect firewall-rule client-interface private none
anyconnect firewall-rule client-interface public none
anyconnect keep-installer installed
anyconnect ssl keepalive 20
anyconnect ssl rekey time none
anyconnect ssl rekey method none
anyconnect dpd-interval client 30
anyconnect dpd-interval gateway 30
anyconnect ssl compression none
anyconnect dtls compression none
anyconnect modules none
anyconnect profiles none
anyconnect ask none
customization none
keep-alive-ignore 4
http-comp gzip
download-max-size 2147483647
upload-max-size 2147483647
post-max-size 2147483647
user-storage none
storage-objects value cookies,credentials
storage-key none
hidden-shares none
smart-tunnel disable
activex-relay enable
unix-auth-uid 65534
unix-auth-gid 65534
file-entry enable
file-browsing enable
url-entry enable
deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information
smart-tunnel auto-signon disable
anyconnect ssl df-bit-ignore disable
anyconnect routing-filtering-ignore disable
smart-tunnel tunnel-policy tunnelall
always-on-vpn profile-setting
password-policy minimum-length 3
password-policy minimum-changes 0
password-policy minimum-lowercase 0
password-policy minimum-uppercase 0
password-policy minimum-numeric 0
password-policy minimum-special 0
password-policy lifetime 0
no password-policy authenticate-enable
quota management-session 0
tunnel-group DefaultL2LGroup type ipsec-l2l
tunnel-group DefaultL2LGroup general-attributes
no accounting-server-group
default-group-policy DfltGrpPolicy
tunnel-group DefaultL2LGroup ipsec-attributes
no ikev1 pre-shared-key
peer-id-validate req
no chain
no ikev1 trust-point
isakmp keepalive threshold 10 retry 2
no ikev2 remote-authentication
no ikev2 local-authentication
tunnel-group DefaultRAGroup type remote-access
tunnel-group DefaultRAGroup general-attributes
no address-pool
no ipv6-address-pool
authentication-server-group LOCAL
secondary-authentication-server-group none
no accounting-server-group
default-group-policy DfltGrpPolicy
no dhcp-server
no strip-realm
no nat-assigned-to-public-ip
no scep-enrollment enable
no password-management
no override-account-disable
no strip-group
no authorization-required
username-from-certificate CN OU
secondary-username-from-certificate CN OU
authentication-attr-from-server primary
authenticated-session-username primary
tunnel-group DefaultRAGroup webvpn-attributes
customization DfltCustomization
authentication aaa
no override-svc-download
no radius-reject-message
no proxy-auth sdi
no pre-fill-username ssl-client
no pre-fill-username clientless
no secondary-pre-fill-username ssl-client
no secondary-pre-fill-username clientless
dns-group DefaultDNS
no without-csd
tunnel-group DefaultRAGroup ipsec-attributes
no ikev1 pre-shared-key
peer-id-validate req
no chain
no ikev1 trust-point
no ikev1 radius-sdi-xauth
isakmp keepalive threshold 300 retry 2
ikev1 user-authentication xauth
no ikev2 remote-authentication
no ikev2 local-authentication
tunnel-group DefaultRAGroup ppp-attributes
no authentication pap
authentication chap
authentication ms-chap-v1
no authentication ms-chap-v2
no authentication eap-proxy
tunnel-group DefaultWEBVPNGroup type remote-access
tunnel-group DefaultWEBVPNGroup general-attributes
no address-pool
no ipv6-address-pool
authentication-server-group LOCAL
secondary-authentication-server-group none
no accounting-server-group
default-group-policy DfltGrpPolicy
no dhcp-server
no strip-realm
no nat-assigned-to-public-ip
no scep-enrollment enable
no password-management
no override-account-disable
no strip-group
no authorization-required
username-from-certificate CN OU
secondary-username-from-certificate CN OU
authentication-attr-from-server primary
authenticated-session-username primary
tunnel-group DefaultWEBVPNGroup webvpn-attributes
customization DfltCustomization
authentication aaa
no override-svc-download
no radius-reject-message
no proxy-auth sdi
no pre-fill-username ssl-client
no pre-fill-username clientless
no secondary-pre-fill-username ssl-client
no secondary-pre-fill-username clientless
dns-group DefaultDNS
no without-csd
tunnel-group DefaultWEBVPNGroup ipsec-attributes
no ikev1 pre-shared-key
peer-id-validate req
no chain
no ikev1 trust-point
no ikev1 radius-sdi-xauth
isakmp keepalive threshold 300 retry 2
ikev1 user-authentication xauth
no ikev2 remote-authentication
no ikev2 local-authentication
tunnel-group DefaultWEBVPNGroup ppp-attributes
no authentication pap
authentication chap
authentication ms-chap-v1
no authentication ms-chap-v2
no authentication eap-proxy
class-map type inspect http match-all _default_gator
match request header user-agent regex _default_gator
class-map type inspect http match-all _default_msn-messenger
match response header content-type regex _default_msn-messenger
class-map type inspect http match-all _default_yahoo-messenger
match request body regex _default_yahoo-messenger
class-map type inspect http match-all _default_windows-media-player-tunnel
match request header user-agent regex _default_windows-media-player-tunnel
class-map type inspect http match-all _default_gnu-http-tunnel
match request args regex _default_gnu-http-tunnel_arg
match request uri regex _default_gnu-http-tunnel_uri
class-map type inspect http match-all _default_firethru-tunnel
match request header host regex _default_firethru-tunnel_1
match request uri regex _default_firethru-tunnel_2
class-map type inspect http match-all _default_aim-messenger
match request header host regex _default_aim-messenger
class-map type inspect http match-all _default_http-tunnel
match request uri regex _default_http-tunnel
class-map type inspect http match-all _default_kazaa
match response header regex _default_x-kazaa-network count gt 0
class-map type inspect http match-all _default_shoutcast-tunneling-protocol
match request header regex _default_icy-metadata regex _default_shoutcast-tunneling-protocol
class-map class-default
match any
class-map inspection_default
match default-inspection-traffic
class-map type inspect http match-all _default_GoToMyPC-tunnel
match request args regex _default_GoToMyPC-tunnel
match request uri regex _default_GoToMyPC-tunnel_2
class-map type inspect http match-all _default_httport-tunnel
match request header host regex _default_httport-tunnel
policy-map type inspect rtsp _default_rtsp_map
description Default RTSP policymap
parameters
policy-map type inspect ipv6 _default_ipv6_map
description Default IPV6 policy-map
parameters
verify-header type
verify-header order
match header routing-type range 0 255
drop log
policy-map type inspect h323 _default_h323_map
description Default H.323 policymap
parameters
no rtp-conformance
policy-map type inspect dns migrated_dns_map_1
parameters
message-length maximum client auto
message-length maximum 512
no message-length maximum server
dns-guard
protocol-enforcement
nat-rewrite
no id-randomization
no id-mismatch
no tsig enforced
policy-map type inspect esmtp _default_esmtp_map
description Default ESMTP policy-map
parameters
mask-banner
no mail-relay
no special-character
no allow-tls
match cmd line length gt 512
drop-connection log
match cmd RCPT count gt 100
drop-connection log
match body line length gt 998
log
match header line length gt 998
drop-connection log
match sender-address length gt 320
drop-connection log
match MIME filename length gt 255
drop-connection log
match ehlo-reply-parameter others
mask
policy-map type inspect ip-options _default_ip_options_map
description Default IP-OPTIONS policy-map
parameters
router-alert action allow
policy-map global_policy
class inspection_default
inspect dns migrated_dns_map_1
inspect ftp
inspect h323 h225 _default_h323_map
inspect h323 ras _default_h323_map
inspect rsh
inspect rtsp
inspect esmtp _default_esmtp_map
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options _default_ip_options_map
inspect icmp
inspect icmp error
inspect pptp
class class-default
policy-map type inspect sip _default_sip_map
description Default SIP policymap
parameters
im
no ip-address-privacy
traffic-non-sip
no rtp-conformance
policy-map type inspect dns _default_dns_map
description Default DNS policy-map
parameters
no message-length maximum client
no message-leI ran those commands while I had the nat off on the router and here are the results. note, i didn't make any changes to the ASA as you only said to remove the router RIP which I did and reloaded and no change.
As long as the statements ip nat outside on the Fastethernet 0/0 is off and the ip nat inside is off on the vlan and the overload statement is taken out, I cannot hit the internet.
CISCO-2811#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CISCO-2811(config)#int
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/1.3
CISCO-2811(config-subif)#no ip nat inside
CISCO-2811(config-subif)#exit
CISCO-2811(config)#inter
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/0
CISCO-2811(config-if)#no ip nat outside
CISCO-2811(config-if)#exit
CISCO-2811(config)#$nside source list 1 interface FastEthernet0/0 overload
Dynamic mapping in use, do you want to delete all entries? [no]: y
CISCO-2811(config)#exit
CISCO-2811#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.10.1.1 202 c47d.4f3b.8ea6 ARPA FastEthernet0/0
Internet 10.10.1.2 - 0019.55a7.2ae8 ARPA FastEthernet0/0
Internet 172.16.10.1 - 0019.55a7.2ae9 ARPA FastEthernet0/1.1
Internet 172.16.10.3 238 0011.5c73.28c1 ARPA FastEthernet0/1.1
Internet 172.16.10.50 72 cc2d.8c78.065a ARPA FastEthernet0/1.1
Internet 172.16.20.1 - 0019.55a7.2ae9 ARPA FastEthernet0/1.2
Internet 172.16.20.3 196 0011.5c73.28c2 ARPA FastEthernet0/1.2
Internet 192.168.1.1 - 0019.55a7.2ae9 ARPA FastEthernet0/1.3
Internet 192.168.1.2 0 0024.e864.01a8 ARPA FastEthernet0/1.3
Internet 192.168.1.3 155 0011.5c73.28c0 ARPA FastEthernet0/1.3
Internet 192.168.1.5 61 4802.2a4c.1c74 ARPA FastEthernet0/1.3
Internet 192.168.1.20 0 5cf9.dd52.5fa9 ARPA FastEthernet0/1.3
Internet 192.168.1.50 0 308c.fb47.f2d9 ARPA FastEthernet0/1.3
Internet 192.168.1.51 1 ec35.8677.4057 ARPA FastEthernet0/1.3
Internet 192.168.1.52 1 b418.d136.ef72 ARPA FastEthernet0/1.3
Internet 192.168.1.53 1 8853.9572.e113 ARPA FastEthernet0/1.3
Internet 192.168.1.54 12 0009.b044.9f23 ARPA FastEthernet0/1.3
Internet 192.168.1.55 0 f47b.5e9a.7ae5 ARPA FastEthernet0/1.3
Internet 192.168.1.149 0 001e.4fc5.a199 ARPA FastEthernet0/1.3
Internet 192.168.1.174 0 b8ac.6fff.af83 ARPA FastEthernet0/1.3
CISCO-2811#sh ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
+ - replicated route, % - next hop override
Gateway of last resort is 10.10.1.1 to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via 10.10.1.1
10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 10.10.1.0/30 is directly connected, FastEthernet0/0
L 10.10.1.2/32 is directly connected, FastEthernet0/0
172.16.0.0/16 is variably subnetted, 4 subnets, 2 masks
C 172.16.10.0/24 is directly connected, FastEthernet0/1.1
L 172.16.10.1/32 is directly connected, FastEthernet0/1.1
C 172.16.20.0/24 is directly connected, FastEthernet0/1.2
L 172.16.20.1/32 is directly connected, FastEthernet0/1.2
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, FastEthernet0/1.3
L 192.168.1.1/32 is directly connected, FastEthernet0/1.3
ASA
ASA5510# sh arp
Inside 10.10.1.2 0019.55a7.2ae8 12342
Outside 199.195.168.113 000c.4243.581a 2
Outside 199.195.168.116 e05f.b947.116b 2436
Outside 199.195.168.120 0017.c58a.1123 9192
DMZ 10.10.0.2 0025.849f.63e0 3192
VOIP 10.10.2.2 000d.bcdc.fc40 7754
ASA5510# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is 199.195.168.113 to network 0.0.0.0
S 172.16.20.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
S 172.16.10.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
S 128.162.1.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
S 128.162.10.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
S 128.162.20.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
C 199.195.168.112 255.255.255.240 is directly connected, Outside
C 10.10.0.0 255.255.255.252 is directly connected, DMZ
C 10.10.1.0 255.255.255.252 is directly connected, Inside
S 192.168.1.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
S* 0.0.0.0 0.0.0.0 [1/0] via 199.195.168.113, Outside
ASA5510# show xlate
35 in use, 784 most used
Flags: D - DNS, e - extended, I - identity, i - dynamic, r - portmap,
s - static, T - twice, N - net-to-net
TCP PAT from DMZ:10.10.0.2 22-22 to Outside:199.195.168.x 2222-2222
flags sr idle 481:54:14 timeout 0:00:00
TCP PAT from Inside:10.10.1.2 22-22 to Outside:199.195.168.x 222-222
flags sr idle 51:06:46 timeout 0:00:00
TCP PAT from VOIP:10.10.2.2 22-22 to Outside:199.195.168.x 2223-2223
flags sr idle 687:32:27 timeout 0:00:00
TCP PAT from Inside:192.168.1.2 3389-3389 to Outside:199.195.168.x 3389-3389
flags sr idle 457:17:01 timeout 0:00:00
TCP PAT from Inside:192.168.1.5 80-80 to Outside:199.195.168.x 8080-8080
flags sr idle 52:18:58 timeout 0:00:00
NAT from Outside:0.0.0.0/0 to any:0.0.0.0/0
flags sIT idle 353:10:21 timeout 0:00:00
UDP PAT from any:10.10.1.2/52581 to Outside:199.195.168.x/52581 flags ri idle 0:00:00 timeout 0:00:30
UDP PAT from any:10.10.1.2/55389 to Outside:199.195.168.x/55389 flags ri idle 0:00:03 timeout 0:00:30
UDP PAT from any:10.10.1.2/51936 to Outside:199.195.168.x/51936 flags ri idle 0:00:04 timeout 0:00:30
UDP PAT from any:10.10.1.2/51345 to Outside:199.195.168.x/51345 flags ri idle 0:00:09 timeout 0:00:30
UDP PAT from any:10.10.1.2/55985 to Outside:199.195.168.x/55985 flags ri idle 0:00:18 timeout 0:00:30
UDP PAT from any:10.10.1.2/49368 to Outside:199.195.168.x/49368 flags ri idle 0:00:22 timeout 0:00:30
UDP PAT from any:10.10.1.2/52441 to Outside:199.195.168.x/52441 flags ri idle 0:00:23 timeout 0:00:30
TCP PAT from any:10.10.1.2/57908 to Outside:199.195.168.x/57908 flags ri idle 0:08:37 timeout 0:00:30
TCP PAT from any:10.10.1.2/57907 to Outside:199.195.168.x/57907 flags ri idle 0:08:37 timeout 0:00:30
TCP PAT from any:10.10.1.2/57906 to Outside:199.195.168.x/57906 flags ri idle 0:08:37 timeout 0:00:30
TCP PAT from any:10.10.1.2/57896 to Outside:199.195.168.x/57896 flags ri idle 0:09:09 timeout 0:00:30
TCP PAT from any:10.10.1.2/57879 to Outside:199.195.168.x/57879 flags ri idle 0:10:23 timeout 0:00:30
TCP PAT from any:10.10.1.2/49441 to Outside:199.195.168.x/49441 flags ri idle 0:20:52 timeout 0:00:30
TCP PAT from any:10.10.1.2/57868 to Outside:199.195.168.x/57868 flags ri idle 0:25:28 timeout 0:00:30
TCP PAT from any:10.10.1.2/60519 to Outside:199.195.168.x/60519 flags ri idle 0:44:11 timeout 0:00:30
TCP PAT from any:10.10.1.2/60491 to Outside:199.195.168.x/60491 flags ri idle 0:44:20 timeout 0:00:30
TCP PAT from any:10.10.1.2/60484 to Outside:199.195.168.x/60484 flags ri idle 0:44:35 timeout 0:00:30
TCP PAT from any:10.10.1.2/60480 to Outside:199.195.168.x/60480 flags ri idle 0:44:51 timeout 0:00:30
TCP PAT from any:10.10.1.2/53851 to Outside:199.195.168.x/53851 flags ri idle 0:54:14 timeout 0:00:30
TCP PAT from any:10.10.1.2/57812 to Outside:199.195.168.x/57812 flags ri idle 0:58:30 timeout 0:00:30
TCP PAT from any:10.10.1.2/57810 to Outside:199.195.168.x/57810 flags ri idle 0:58:32 timeout 0:00:30
TCP PAT from any:10.10.1.2/53847 to Outside:199.195.168.x/53847 flags ri idle 1:00:18 timeout 0:00:30
TCP PAT from any:10.10.1.2/57808 to Outside:199.195.168.x/57808 flags ri idle 1:07:58 timeout 0:00:30
TCP PAT from any:10.10.1.2/60406 to Outside:199.195.168.x/60406 flags ri idle 1:42:13 timeout 0:00:30
TCP PAT from any:10.10.1.2/49259 to Outside:199.195.168.x/49259 flags ri idle 7:39:44 timeout 0:00:30
TCP PAT from any:10.10.1.2/49191 to Outside:199.195.168.x/49191 flags ri idle 7:42:39 timeout 0:00:30
TCP PAT from any:10.10.1.2/55951 to Outside:199.195.168.x/55951 flags ri idle 23:11:40 timeout 0:00:30
TCP PAT from any:10.10.1.2/55944 to Outside:199.195.168.x/55944 flags ri idle 23:15:19 timeout 0:00:30
TCP PAT from any:10.10.1.2/55942 to Outside:199.195.168.x/55942 flags ri idle 23:15:24 timeout 0:00:30
ASA5510# sh conn all
149 in use, 815 most used
TCP Outside 74.125.193.108:993 Inside 10.10.1.2:57879, idle 0:12:37, bytes 6398, flags UIO
TCP Outside 174.35.24.74:80 Inside 192.168.1.20:53879, idle 0:00:01, bytes 0, flags saA
TCP Outside 174.35.24.74:80 Inside 192.168.1.20:53878, idle 0:00:01, bytes 0, flags saA
TCP Outside 17.149.36.177:5223 Inside 10.10.1.2:60480, idle 0:16:53, bytes 4539, flags UIO
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53877, idle 0:00:02, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53876, idle 0:00:02, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53875, idle 0:00:05, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53874, idle 0:00:05, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53872, idle 0:00:11, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53871, idle 0:00:11, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53868, idle 0:00:08, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53867, idle 0:00:08, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53860, idle 0:00:17, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53859, idle 0:00:17, bytes 0, flags saA
TCP Outside 17.172.233.95:5223 Inside 10.10.1.2:49191, idle 0:18:48, bytes 7384, flags UIO
TCP Outside 17.178.100.43:443 Inside 10.10.1.2:57810, idle 0:56:21, bytes 5797, flags UFIO
TCP Outside 23.206.216.93:80 Inside 10.10.1.2:53847, idle 0:54:15, bytes 2683, flags UFIO
TCP Outside 143.127.93.90:80 Inside 10.10.1.2:49259, idle 0:12:20, bytes 13315, flags UIO
TCP Outside 74.125.225.53:443 Inside 192.168.1.20:53864, idle 0:00:11, bytes 0, flags saA
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49204, idle 0:00:04, bytes 67, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:50122, idle 0:00:07, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63275, idle 0:00:08, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63306, idle 0:00:18, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65059, idle 0:00:22, bytes 46, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64681, idle 0:00:30, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64661, idle 0:00:30, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.20:55618, idle 0:00:32, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65056, idle 0:00:33, bytes 48, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:59433, idle 0:00:41, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.20:52178, idle 0:00:42, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:61414, idle 0:00:43, bytes 34, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65438, idle 0:00:44, bytes 44, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63686, idle 0:00:44, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65416, idle 0:00:45, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:53047, idle 0:00:47, bytes 32, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:62213, idle 0:00:46, bytes 74, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:52347, idle 0:00:46, bytes 92, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:58069, idle 0:00:46, bytes 64, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:50753, idle 0:00:46, bytes 74, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65381, idle 0:00:50, bytes 50, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65082, idle 0:00:50, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64038, idle 0:00:50, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49309, idle 0:00:51, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64034, idle 0:00:51, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49197, idle 0:00:51, bytes 50, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64728, idle 0:00:51, bytes 49, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64309, idle 0:00:51, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63289, idle 0:00:51, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64174, idle 0:00:52, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:39286, idle 0:01:09, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63726, idle 0:01:09, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65482, idle 0:01:12, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65091, idle 0:01:13, bytes 61, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64976, idle 0:01:13, bytes 57, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63749, idle 0:00:51, bytes 103, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64043, idle 0:01:14, bytes 52, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64267, idle 0:01:24, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64467, idle 0:01:26, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65504, idle 0:01:26, bytes 46, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:38946, idle 0:01:35, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63701, idle 0:01:38, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63879, idle 0:01:46, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:58516, idle 0:01:49, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63227, idle 0:01:51, bytes 62, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:65446, idle 0:01:53, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49166, idle 0:01:55, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:56680, idle 0:02:01, bytes 33, flags -
UDP Outside 192.55.83.30:53 Inside 192.168.1.2:65073, idle 0:00:44, bytes 50, flags -
TCP Outside 74.125.193.109:993 Inside 10.10.1.2:57808, idle 0:39:33, bytes 6392, flags UFIO
TCP Outside 74.125.225.54:443 Inside 192.168.1.20:53863, idle 0:00:13, bytes 0, flags saA
TCP Outside 143.127.93.89:80 Inside 10.10.1.2:60519, idle 0:46:30, bytes 346, flags UO
TCP Outside 74.125.225.32:443 Inside 192.168.1.20:53881, idle 0:00:01, bytes 0, flags saA
TCP Outside 74.125.225.32:443 Inside 192.168.1.20:53880, idle 0:00:01, bytes 0, flags saA
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:60627, idle 0:00:39, bytes 78, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:52088, idle 0:00:39, bytes 86, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:50533, idle 0:00:39, bytes 76, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:63347, idle 0:00:39, bytes 80, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:62213, idle 0:00:40, bytes 37, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:52347, idle 0:00:40, bytes 46, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:58069, idle 0:00:40, bytes 32, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:50753, idle 0:00:40, bytes 37, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.174:52254, idle 0:01:09, bytes 43, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.174:50791, idle 0:01:25, bytes 35, flags -
TCP Outside 74.125.225.46:443 Inside 192.168.1.20:53870, idle 0:00:08, bytes 0, flags saA
TCP Outside 17.173.255.101:443 Inside 10.10.1.2:53851, idle 0:56:33, bytes 58, flags UfIO
TCP Outside 64.4.23.147:33033 Inside 10.10.1.2:55944, idle 0:44:45, bytes 558164, flags UFIO
TCP Outside 74.125.225.35:443 Inside 192.168.1.20:53869, idle 0:00:09, bytes 0, flags saA
UDP Outside 64.4.23.175:33033 Inside 192.168.1.174:26511, idle 0:01:17, bytes 28, flags -
UDP Outside 192.54.112.30:53 Inside 192.168.1.2:65380, idle 0:00:44, bytes 49, flags -
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57908, idle 0:10:47, bytes 7895, flags UIO
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57907, idle 0:10:49, bytes 20323, flags UIO
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57906, idle 0:10:47, bytes 6539, flags UIO
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57868, idle 0:27:44, bytes 6395, flags UIO
TCP Outside 91.190.218.59:443 Inside 10.10.1.2:55942, idle 0:41:39, bytes 2727, flags UFIO
TCP Outside 17.172.233.123:5223 Inside 10.10.1.2:49441, idle 0:23:10, bytes 4409, flags UIO
TCP Outside 74.125.225.41:443 Inside 192.168.1.20:53862, idle 0:00:16, bytes 0, flags saA
TCP Outside 74.125.225.41:443 Inside 192.168.1.20:53861, idle 0:00:16, bytes 0, flags saA
TCP Outside 143.127.93.115:80 Inside 10.10.1.2:60406, idle 0:42:59, bytes 970, flags UFIO
TCP Outside 143.127.93.118:80 Inside 10.10.1.2:60484, idle 0:46:54, bytes 328, flags UO
TCP Outside 17.172.233.98:5223 Inside 10.10.1.2:57896, idle 0:11:28, bytes 5081, flags UIO
UDP Outside 111.221.74.16:33033 Inside 192.168.1.174:26511, idle 0:01:18, bytes 31, flags -
TCP Outside 17.149.36.103:5223 Inside 192.168.1.174:60729, idle 0:00:04, bytes 0, flags saA
UDP Outside 192.5.6.30:53 Inside 192.168.1.2:65317, idle 0:00:44, bytes 51, flags -
UDP Outside 192.12.94.30:53 Inside 192.168.1.2:65356, idle 0:00:44, bytes 54, flags -
TCP Outside 17.149.36.180:5223 Inside 10.10.1.2:55951, idle 0:46:08, bytes 14059, flags UFIO
UDP Outside 111.221.74.28:33033 Inside 192.168.1.174:26511, idle 0:01:20, bytes 33, flags -
TCP Outside 63.235.20.160:80 Inside 192.168.1.20:53873, idle 0:00:08, bytes 0, flags saA
TCP Outside 50.19.127.112:443 Inside 192.168.1.50:60678, idle 0:00:00, bytes 0, flags saA
TCP Outside 65.55.122.234:80 Inside 192.168.1.174:60728, idle 0:00:14, bytes 0, flags saA
TCP Outside 65.55.122.234:80 Inside 192.168.1.174:60727, idle 0:00:15, bytes 0, flags saA
TCP Outside 65.55.122.234:80 Inside 192.168.1.174:60726, idle 0:00:15, bytes 0, flags saA
TCP Outside 65.55.122.234:443 Inside 192.168.1.174:2492, idle 0:00:16, bytes 0, flags saA
TCP Outside 65.55.122.234:2492 Inside 192.168.1.174:2492, idle 0:00:16, bytes 0, flags saA
UDP Outside 157.55.56.170:33033 Inside 192.168.1.174:26511, idle 0:01:21, bytes 37, flags -
TCP Outside 74.125.230.207:443 Inside 192.168.1.20:53866, idle 0:00:11, bytes 0, flags saA
TCP Outside 74.125.230.207:443 Inside 192.168.1.20:53865, idle 0:00:11, bytes 0, flags saA
UDP Outside 111.221.74.18:33033 Inside 192.168.1.174:26511, idle 0:01:17, bytes 29, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:55546, idle 0:00:06, bytes 46, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:60277, idle 0:00:06, bytes 46, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:55618, idle 0:00:34, bytes 43, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:60627, idle 0:00:36, bytes 78, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:52088, idle 0:00:36, bytes 86, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:50533, idle 0:00:36, bytes 76, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:63347, idle 0:00:36, bytes 80, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:56958, idle 0:01:24, bytes 34, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:51360, idle 0:01:26, bytes 34, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.174:50791, idle 0:01:27, bytes 35, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:54134, idle 0:01:46, bytes 34, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.174:58516, idle 0:01:50, bytes 51, flags -
TCP Outside 23.207.7.46:80 Inside 192.168.1.55:59350, idle 0:00:02, bytes 0, flags saA
TCP Outside 23.207.7.46:80 Inside 192.168.1.55:59349, idle 0:00:16, bytes 0, flags saA
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:50122, idle 0:00:09, bytes 43, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:48088, idle 0:00:42, bytes 33, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:62213, idle 0:00:45, bytes 74, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:52347, idle 0:00:45, bytes 92, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:58069, idle 0:00:45, bytes 64, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:50753, idle 0:00:45, bytes 74, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:61414, idle 0:00:47, bytes 34, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:54481, idle 0:01:08, bytes 33, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:52254, idle 0:01:09, bytes 43, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:40285, idle 0:01:34, bytes 33, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:65446, idle 0:01:55, bytes 43, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:46155, idle 0:02:00, bytes 33, flags -
UDP Outside 66.104.81.70:5070 Inside 192.168.1.174:57609, idle 0:00:11, bytes 46, flags -
UDP Outside 64.4.23.156:33033 Inside 192.168.1.174:26511, idle 0:01:14, bytes 38, flags -
TCP Outside 65.54.167.15:12350 Inside 10.10.1.2:60491, idle 0:11:02, bytes 1405, flags UIO
TCP Outside 17.172.192.35:443 Inside 10.10.1.2:57812, idle 0:56:11, bytes 6116, flags UFIO
UDP Outside 157.55.56.176:33033 Inside 192.168.1.174:26511, idle 0:01:16, bytes 32, flags -
TCP Inside 192.168.1.20:53667 NP Identity Ifc 10.10.1.1:22, idle 0:00:00, bytes 37555, flags UOB
TCP Inside 10.10.1.2:53431 NP Identity Ifc 10.10.1.1:22, idle 0:09:03, bytes 20739, flags UOB
Ran on the ASA while overload statements were down on the router:
ASA5510# packet-tracer input Inside tcp 192.168.1.100 12345 8.8.8.8 80
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 0.0.0.0 0.0.0.0 Outside
Phase: 2
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
Phase: 3
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 4
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
Phase: 5
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 6
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 1988699, packet dispatched to next module
Result:
input-interface: Inside
input-status: up
input-line-status: up
output-interface: Outside
output-status: up
output-line-status: up
Action: allow
Had to put these back in to get to the internet:
CISCO-2811#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CISCO-2811(config)#inter
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/0
CISCO-2811(config-if)#ip nat
CISCO-2811(config-if)#ip nat Outside
CISCO-2811(config-if)#exit
CISCO-2811(config)#in
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/1.3
CISCO-2811(config-subif)#ip nat inside
CISCO-2811(config-subif)#exit
CISCO-2811(config)#$de source list 1 interface FastEthernet0/0 overload
CISCO-2811(config)#
Screenshot of ASDM: -
Cisco 2811 Router with 3 ADSL card and load balancing
Dear All,
I have few queries:
1. Does Cisco 2811 Router support 3 ADSL card?
2. We are the ISP. I want to do load balancing with 3 dsl
line on Cisco 2811 Router.
Please send me the linke for this configuration.
Thanks/Regards
Atulhi
In 2811 you have 4 HWIC and 1 NME you can install 1-port ADSL WAN Interface Cardon the HWIC slots.
Also just enable 3 default (equal cost) routes towards the interfaces which will take care of the load balancing.
if you need more info and inputs do post out with ur requirements along with network topology in place at present..
regds -
CUCM 9.1.1 - MGCP gateway won't register to my 2811
Hello
I am trying to add a MGCP gateway on a 2811.
I have configured as per the book, but it is not registering,
here is my Router config:
2811 uptime is 2 hours, 4 minutes
System returned to ROM by power-on
System image file is "flash:c2800nm-adventerprisek9-mz.124-11.XJ4.bin"
Cisco 2811 (revision 53.50) with 509952K/14336K bytes of memory.
Processor board ID FHK1302F0YV
3 FastEthernet interfaces
24 Serial interfaces
1 Channelized T1/PRI port
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
125440K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
2811#sh run
Building configuration...
Current configuration : 7125 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname 2811
boot-start-marker
boot-end-marker
card type t1 0 2
enable secret 5 $1$ax07$1yOFpGS1rHGYm873l9n9q/
no aaa new-model
clock timezone PCLAIRE -5
clock summer-time PCLAIRE recurring
network-clock-participate wic 2
network-clock-select 1 T1 0/2/0
ip cef
no ip dhcp use vrf connected
ip domain name homelab.local
multilink bundle-name authenticated
isdn switch-type primary-ni
voice-card 0
dspfarm
dsp services dspfarm
controller T1 0/2/0
framing esf
linecode b8zs
pri-group timeslots 1-24
description Home_PBX
vlan internal allocation policy ascending
interface FastEthernet0/0/0
description To Home Network$ETH-LAN$
ip address 192.168.15.50 255.255.255.0
duplex auto
speed auto
interface Serial0/2/0:23
description Home_PBX
no ip address
encapsulation ppp
isdn switch-type primary-ni
isdn incoming-voice voice
control-plane
voice-port 0/2/0:23
description Home_PBX
ccm-manager mgcp
ccm-manager config server 192.168.15.11 - THIS IS THE SUBSCRIBER , SHOULD IT BE THE PUBLISHER ?
ccm-manager config
mgcp
gateway
timer receive-rtp 1200
Here is what I get:
2811(config)#do sh ccm-manager
MGCP Domain Name: 2811.homelab.local
Priority Status Host
============================================================
Primary None
First Backup None
Second Backup None
Current active Call Manager: None
Backhaul/Redundant link port: 2428
Failover Interval: 30 seconds
Keepalive Interval: 15 seconds
Last keepalive sent: 09:55:04 PCLAIRE Jan 16 2014 (elapsed time: 02:00:24)
Last MGCP traffic time: 11:34:19 PCLAIRE Jan 16 2014 (elapsed time: 00:21:08)
Last failover time: None
Last switchback time: None
Switchback mode: Graceful
MGCP Fallback mode: Not Selected
Last MGCP Fallback start time: None
Last MGCP Fallback end time: None
MGCP Download Tones: Disabled
Backhaul/Redundant link is down
Configuration Auto-Download Information
=======================================
No configurations downloaded
Current state: Downloading XML file
Configuration Download statistics:
Download Attempted : 1
Download Successful : 1
Download Failed : 0
Configuration Attempted : 0
Configuration Successful : 0
Configuration Failed(Parsing): 0
Configuration Failed(config) : 0
Last config download command:
FAX mode: cisco
Configuration Error History:
2811(config)#
Any help greatly appreciated
John BachmanStill same problem, I have erased all that related to mgcp on my router, to start from scratch
2811(config)#controller T1 0/2/0
2811(config-controller)#pri-group timeslots 1-24 service mgcp
Cannot overwrite no serv type with one. Unconfigure existing configuration and reconfigure
2811(config-controller)#
Where is this error coming from ??
Here is what I want to try:
192.168.15.10 - pub
192.168.15.11 - sub
controller T1 0/2/0
pri-group timeslots 1-24 service mgcp
interface Serial0/0/0:23
isdn bind-l3 ccm-manager
ccm-manager config server 192.168.15.10 192.168.15.11
ccm-manager config
ccm-manager redundant-host 192.168.15.11
ccm-manager mgcp
mgcp
mgcp call-agent 192.168.15.10 service-type mgcp version 0.1 -
Video/Voice Conference -8 Error Explained for Cisco Routers
I cannot tell you how long I have spent trying to figure out this problem. We have a bunch of macs sitting behind a NATed Cisco 2811 router, and iChat will just never work, throwing the good ole' -8 error.
Having a good understanding of SIP, I decided to get down an dirty with the investigation of why iChat doesn't work behind some routers, while it does on others.
iChat uses SIP, but as I have found, Apple's implementation of it does not completely honor the RFC. This is the root cause of iChat not working behind enterprise grade routers that have SIP ALG activated (details later).
Apple uses its own flavor of NAT traversal: SNATMAP. This is an Apple service that is utilized every time a video/voice conference is created from iChat. For those of you familiar with SIP, SNATMAP essentially performs the same function as a STUN server. This service abstracts the port specifications necessary to get around NATs to a server on the public Internet.
With some routers, this SNATMAP seems to work fine. With others, not so much. I honestly don't have too deep of an understanding of SNATMAP so I cannot get into too much detail as to why it doesn't work with some routers. If anyone knows, please chime in!
I can, however, clearly indicate why it doesn't work behind routers that have a SIP ALG, which essentially has the intelligence to pick apart to SIP packet to make them NAT friendly. Basically, there is a portion of SIP packets called the SDP (Session Description Protocol) that provides all of the information necessary to set up the voice and video stream. The SIP RFC calls for this section to include information like the connection IP address, port, video codec, audio codec, etc. HOWEVER, Apple's implementation of iChat DOES NOT INCLUDE THE PORT IN THE SDP. Therefore, when a SIP ALG tries to intelligently convert the port, it isn't there to change. Even if it does manage to insert a port number into the SDP, the iChat client receiving the SIP packet doesn't respect that port number and just dumbly sends the request back to the default SIP port (5060).
Here is a little flow of the process:
1. A SIP packet is sent out from iChat to the cisco router
2. Cisco intercepts the packet, changes the private IP address of my computer to the public IP address of the interface, and changes the port to one that it assigns on the public interface. So, basically the SIP packet enters the cisco with the SDP info like 192.168.100.137:5060 and leaves the Cisco like <public IP>:1877.
3. On the receiving end, the SIP packet and SDP section is read with our DSL connection's public IP address, so when it tries to make contact back, requests are sent to the DSL public IP address and not an unrouteable private IP. Also, it sends to the port specified in the SDP section.
4. When a packet comes in from the peer, the destination is something like <public IP>:1877. The cisco NAT translation table remembers that things destined to port 1877 should be converted to 192.168.100.137 on port 5060. The SDP section of the SIP packet is modified and things are peachy.
5. This happens back and forth for all SIP messages that traverse the NAT.
iChat is not SIP RFC compliant which is why we are having these natting issues. iChat does not specify a port in the SDP portion of the SIP messages it is sending out: a big no-no. Therefore, when the recipient iChat is sending back its requests to 207.182.233.32, it is sending it to port 5060 instead of assigned port 1877. The public port 5060 is blocked, and is not routed to any specific computer, resulting in a timeout. Here is the Cisco output 'debug ip nat sip'
001892: .Oct 2 22:53:04.108 PCTime: NAT: SIP: [0] processing INVITE message
001893: .Oct 2 22:53:04.108 PCTime: NAT: SIP: [0] register:0 door_created:0
001894: .Oct 2 22:53:04.108 PCTime: NAT: SIP: [0] translated embedded address 192.168.100.138-><public IP>
001895: .Oct 2 22:53:04.108 PCTime: NAT: SIP: [0] No port present. Use new port 5060->1210
As you can see, it is processing the INVITE request and translating the internal IP address to the public one.
However, it reports no port present, meaning that the port specification in the SDP section of the SIP packet is not present. It does a port translation because it feels obligated to, but iChat doesn't respect that on the other end and sends to 5060 anyway which is not mapped to any specific internal IP addess, so, alas, it doesn't work.
Now, that being, said, this explains why iChat doesn't work behind SIP ALGs. However, if you are able to disable the SIP ALG (on cisco: 'no ip nat service sip udp 5060'), it still doesn't work. With the ALG turned off, the SDP translations don't occur, but for some reason SNATMAP still doesn't work either. I am thinking that could be due to a nat issue, but I haven't figured that out yet. Anyone's insight would be appreciated!
Hope this helps anyone out there seeking help / console with iChat Error -8 issues behind an enterprise grade router.
Hopefully we can figure out why iChat's SNATMAP implementation doesn't work with a Cisco NAT next...Hi
Ok for the Homehub's.
UPnP should be enabled.
Set the Quicktime streaming setting, goto sys prefs/quicktime/streaming/streaming speed, set to 1.5mbps(dont use automatic)
In ichats prefs click on video and change bandwidth limit to NONE.
Goto to sys prefs/sharing/firewall and turn on(dont add any ports for ichat, leave anything that is ticked ticked).
Restart ichat.
And try connecting to me defcom1 .mac account.
Tony -
Hi All,
I have a cisco 2811 that is high in CPU usage. Below is my IOS version and process usage details.
Cisco IOS Software, 2800 Software (C2800NM-IPBASEK9-M), Version 12.4(24)T4, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 03-Sep-10 05:39 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
ipscape-myob uptime is 6 weeks, 5 days, 17 hours, 18 minutes
System returned to ROM by reload at 10:33:59 UTC Thu Apr 10 2014
System image file is "flash:c2800nm-ipbasek9-mz.124-24.T4.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 2811 (revision 53.51) with 514048K/10240K bytes of memory.
Processor board ID FHK1238F1D4
2 FastEthernet interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
CPU utilization for five seconds: 90%/77%; one minute: 79%; five minutes: 76%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
8 20693808 28614857 723 7.67% 1.24% 0.44% 0 IP SLAs Respond e
91 13460456 18459988 729 3.27% 0.67% 0.31% 0 IP Input
143 3167640 1026953957 3 1.19% 1.62% 1.68% 0 HQF Shaper Back g
184 809676 128826693 6 0.39% 0.38% 0.39% 0 PPP manager
196 1072 112 9571 0.31% 0.23% 0.06% 514 Virtual Exec
185 771340 128826711 5 0.23% 0.18% 0.16% 0 PPP Events
Could you please provide me some info on this issues.
Thank You!Has this been something that just recently started happening, or have you had this issue for a while? Have you installed any new programs recently?
You may want to download Glary Utilities, which is a free software(they will ask you if you want to go Pro, just say no, the free version works very well). There is a module for startup manager. You can go in and disable stuff that starts with the computer. I would advise unchecking adobe, java, quicktime, printers, etc. Anything that doesn't REALLY need to start with the computer. The nice thing with Glary is that you can restart the computer, and if you find that you need one of the programs to start with windows, you can go back in and enable it again.
The Celeron 925 processor in your computer is a decent entry level processor, but if there are too many programs running in the background, it can bog down quick. I would also recommend downloading and running Malwarebytes Anti-malware, to be sure that there is nothing malicous running in the background.
Qosmio X875 i7-3630QM, 32GB RAM, OCZ SSD Qosmio X505 i7-920XM, PM55, 16GB RAM, OCZ SSD
Satellite Pro L350 T9900, GM45, 8GB RAM , Intel 320 SSD (my baby) Satellite L655 i7-620M, HM55, 8GB RAM, Intel 710 SSD (travel system) -
I recently inherited a Cisco 2811 Router. I want to play with some Voice services as a test lab. I currently have a production CUCM 8.6 environment I would like to connect it to. It has IOS C2800NM-ENTSERVICESK9-M 12.4(17). If I program it to register with my CCM, it always gets stuck at ""registering with CCM". Oddly enough, I can assign it SCCP based phones, but anytime I try to play with SIP phones, the phones never register. I am thinking its related to the "Registering with CCM" and "Current active call manager : none" when I do a show-ccm. Do I have the wrong IOS for voice? I am more familiar with the X9XX series routers where you can do a sh-license and it tells you it has the UC license. If that is the case, what is the minimum license level to support voice on the 2811 router to connect it to my CUCM8.6 using MGCP?
Thank You,
DavidHi David,
IOS on 2800 series routers is implemented differently , hence we do not have any licenses. Voice should work as long as we have the right IOS image. Having said that , If voice components were not enabled , we would not have been put in any commands , for MGCP etc.
Coming to the IOS version , while the image is indeed quite old , i don't think it should affect the registration . As a good practice , it is recommended to have the IOS versions and CUCM versions 'compatible', which is tabulated in the link below :
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/uc_system/unified/communications/system/versions/IPTMtrix.html
Moving on to the registration , here are some quick pointers:
1. make sure that the config on GW is as per the link below :
http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-callmanager/42105-vg200-cfg.html
2. The GW name should match that on CUCM. Match the name in the first line of "show ccm-manager" to the name that has been added to CUCM.
3. Also , ensure the modules added on CUCM are correct.
HTH,
Harsh -
How to recover mbrd_e1t1_vic_connect: setup failed on cisco 2811 routers
Dear All Experts
I have three cisco 2811 routers, Router A has both 4 FXS & 4FXO port , Router B & Router C have 4 FXS port. connect with Alcatel PABX.
Now, the problem is ph lines are down after 3 days or more. Whenever down, i try to refresh voice port , with " shut & no shut " on each routers.Now i face the problem that is whenever i make shut & no shut on Router B site, ph line is ok there. But in Router C site , ph line is down. So i refresh @ Router C site,ph line is ok but in the router B site , ph line is down again.
I try several ways for shut & no shut. i have no idea. i checked log file on Router A , here is
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0pt 5.4pt 0pt 5.4pt;
mso-para-margin:0pt;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";}
Aug 18 16:03:55.306 UTC: mbrd_e1t1_vic_connect: setup failed
Aug 18 16:03:55.306 UTC: flex_dsprm_tdm_xconn: voice-port(0/3/0), dsp_channel(/0
/0/0)
Aug 18 16:12:56.331 UTC: mbrd_e1t1_vic_connect: setup failed
Aug 18 16:12:56.331 UTC: flex_dsprm_tdm_xconn: voice-port(0/3/0), dsp_channel(/0
/0/0)
Aug 18 16:12:56.335 UTC: mbrd_e1t1_vic_connect: setup failed
Aug 18 16:12:56.335 UTC: flex_dsprm_tdm_xconn: voice-port(0/3/0), dsp_channel(/0
/0/0)
Aug 18 16:14:37.405 UTC: mbrd_e1t1_vic_connect: setup failed
Aug 18 16:14:37.405 UTC: flex_dsprm_tdm_xconn: voice-port(0/3/2), dsp_channel(/0
/0/0)
Aug 18 16:19:40.278 UTC: mbrd_e1t1_vic_connect: setup failed
Aug 18 16:19:40.278 UTC: flex_dsprm_tdm_xconn: voice-port(0/3/0), dsp_channel(/0
/0/0)
Aug 18 16:22:34.597 UTC: mbrd_e1t1_vic_connect: setup failed
Aug 18 16:22:34.597 UTC: flex_dsprm_tdm_xconn: voice-port(0/3/2), dsp_channel(/0
/0/0)
Aug 18 16:36:37.065 UTC: mbrd_e1t1_vic_connect: setup failed
Aug 18 16:36:37.065 UTC: flex_dsprm_tdm_xconn: voice-port(0/3/0), dsp_channel(/0
/0/0)
So give me advise & guide to recover this problem . I have really big problem now. help me!
thanks a lotHere it's sh ver .All three routers are same version , flash, model except RouterB & C has only 4 FXS voice interface.
RouterA#sh ver
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(8), RE
EASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 15-May-06 14:54 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)
RouterA uptime is 12 weeks, 1 day, 23 hours, 11 minutes
System returned to ROM by reload at 08:59:03 UTC Wed May 26 2010
System restarted at 09:01:16 UTC Wed May 26 2010
System image file is "flash:c2800nm-spservicesk9-mz.124-8.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 2811 (revision 53.51) with 251904K/10240K bytes of memory.
Processor board ID FHK0949F1W9
2 FastEthernet interfaces
4 Serial(sync/async) interfaces
4 Voice FXO interfaces
4 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
RouterA#sh flash
-#- --length-- -----date/time------ path
1 26725176 Dec 2 2005 09:30:24 +06:30 c2800nm-spservicesk9-mz.123-11.T8.bin
2 1646 Dec 2 2005 09:39:00 +06:30 sdmconfig-2811.cfg
3 4052480 Dec 2 2005 09:39:22 +06:30 sdm.tar
4 812032 Dec 2 2005 09:39:38 +06:30 es.tar
5 1007616 Dec 2 2005 09:39:52 +06:30 common.tar
6 1038 Dec 2 2005 09:40:06 +06:30 home.shtml
7 113152 Dec 2 2005 09:40:18 +06:30 home.tar
8 511939 Dec 2 2005 09:40:32 +06:30 128MB.sdf
9 28532876 Jul 5 2006 05:12:32 +06:30 c2800nm-spservicesk9-mz.124-8.bin
10 10829 Aug 9 2010 14:03:44 +06:30 tftp
2228224 bytes available (61788160 bytes used)
it seems to be upgrade IOS version 123--11.T8 to 124-8 . I'm not exactly know the history of these routers. -
How to register the same schema with same URL
I'm getting ORA-31085 error when try to register the same schema with same URl.
My requirement is that I should be able to reregister the same schema with the same URL .
I'm using the following function :
PROCEDURE validateXmlSchema(inp_xmlMsg IN VARCHAR2,
out_isValidDoc IN OUT NUMBER,
inp_xmlSchema IN OUT VARCHAR2,
out_varchar_notused OUT VARCHAR2)IS
xmldoc XMLType;
res number;
BEGIN
xmldoc := XMLtype(inp_xmlMsg);
res := xmldoc.isSchemaValid(inp_xmlSchema);
IF (xmldoc.isSchemaValid = 1) THEN
out_isValidDoc := 1;
ELSE
out_isValidDoc := 0;
END IF;
END validateXmlSchema;
This is used recursively.Until the schema is not validated for a given URL this function should keep on throwing error and once the schema is validated the data should be inserted in the DB.
But its not happening as of now instead the ORA-31085 is thrown second time.
Plz provide pointers to solve the issue."mjs" <[email protected]> wrote in message
news:g7kjk5$o6$[email protected]..
> "mjs" <[email protected]> wrote in message
> news:g7gl2g$i3d$[email protected]..
>> "Zorrrro" <[email protected]> wrote
in message
>> news:g7gcjv$a6n$[email protected]..
>>> I'm completely nuckered trying to find an answer
for this...
>>>
>>> Does anyone know how to keep the same width an
position of the submenus
>>> of a
>>> horizontal dropdown menu?
>>> Thank you in advance.
>>>
>>> Cheers.
>>
>> Doesn't a simple style="width:200px" in the input
tag work?
>
> I'll asume the answer is "yes", then. ;) You're welcome.
I believe the OP is talking about a dropdown menu like this
one
http://www.tjkdesign.com/articles/keyboard_friendly_dropdown_menu/default.asp
not about a "select menu".
I could be wrong though...
Thierry
Articles and Tutorials:
http://www.TJKDesign.com/go/?0
http://developer.yahoo.com/
helps you build applications and mashups -
Can not register a new machine with Updatemanager
Hi,
I just install a new machine with Solaris 10 using a Flash image and Live Upgrade. The original machine from we create the Flash image was registered succesfull using Update Manager.
Now, when I try to register the new machine, the applications ask me the user and password, but do not makes anything. The dialog freeze. The only way to stop the Update Manager is killing them (at the end is the full java error stack).
I try with sconadm,
sconadm register -a -r /var/tmp/registration.profile
Unsuccessfull too, with the same stack error (Caused by: javax.management.InstanceNotFoundException: ).
I'm bored with the Solaris patch system: all the weekend was saying error 500 for all my other registered machines, and now I can not register a new machine....
This system fails all the time.. Is runing under W2K3 server???
Any Idea?
Thanks in advance.
H.
P.S: Error stack output:
Exception occurred during event dispatching:
java.lang.reflect.UndeclaredThrowableException
at $Proxy1.getInstanceName(Unknown Source)
at com.sun.scn.client.SCNClientSession.login(SCNClientSession.java:371)
at com.sun.cns.basicreg.cacao.ClientLoginCacaoAdapter.loginAccount(ClientLoginCacaoAdapter.java:209)
at com.sun.cns.basicreg.wizard.cli.CmdLineWizard.outCall(CmdLineWizard.java:1109)
at com.sun.cns.basicreg.wizard.cli.CmdLineWizard.output(CmdLineWizard.java:773)
at com.sun.cns.basicreg.wizard.swing.WizardPanel.isNavigationAllowed(WizardPanel.java:1337)
at com.sun.cns.basicreg.wizard.swing.WizardDialog.okByNavigationListener(WizardDialog.java:583)
at com.sun.cns.basicreg.wizard.swing.WizardDialog.access$100(WizardDialog.java:64)
at com.sun.cns.basicreg.wizard.swing.WizardDialog$NextButtonActionListener.actionPerformed(WizardDialog.java:404)
at javax.swing.AbstractButton.fireActionPerformed(AbstractButton.java:1849)
at javax.swing.AbstractButton$Handler.actionPerformed(AbstractButton.java:2169)
at javax.swing.DefaultButtonModel.fireActionPerformed(DefaultButtonModel.java:420)
at javax.swing.DefaultButtonModel.setPressed(DefaultButtonModel.java:258)
at javax.swing.plaf.basic.BasicButtonListener.mouseReleased(BasicButtonListener.java:236)
at java.awt.Component.processMouseEvent(Component.java:5517)
at javax.swing.JComponent.processMouseEvent(JComponent.java:3135)
at java.awt.Component.processEvent(Component.java:5282)
at java.awt.Container.processEvent(Container.java:1966)
at java.awt.Component.dispatchEventImpl(Component.java:3984)
at java.awt.Container.dispatchEventImpl(Container.java:2024)
at java.awt.Component.dispatchEvent(Component.java:3819)
at java.awt.LightweightDispatcher.retargetMouseEvent(Container.java:4212)
at java.awt.LightweightDispatcher.processMouseEvent(Container.java:3892)
at java.awt.LightweightDispatcher.dispatchEvent(Container.java:3822)
at java.awt.Container.dispatchEventImpl(Container.java:2010)
at java.awt.Window.dispatchEventImpl(Window.java:1791)
at java.awt.Component.dispatchEvent(Component.java:3819)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:463)
at java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.java:242)
at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:163)
at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:153)
at java.awt.Dialog$1.run(Dialog.java:535)
at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:209)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:461)
at java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.java:242)
at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:163)
at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:157)
at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:149)
at java.awt.EventDispatchThread.run(EventDispatchThread.java:110)
Caused by: javax.management.InstanceNotFoundException: com.sun.scn:name=SCNBaseServiceFactory,assetSubProfile=Factory,host=alcaudon.tsc.uc3m.es,assetProfile=Factory,scnType=ServiceFactory,Vendor=Sun Microsystems Inc
at com.sun.jmx.interceptor.DefaultMBeanServerInterceptor.getMBean(DefaultMBeanServerInterceptor.java:1010)
at com.sun.jmx.interceptor.DefaultMBeanServerInterceptor.getClassLoaderFor(DefaultMBeanServerInterceptor.java:1349)
at com.sun.jmx.mbeanserver.JmxMBeanServer.getClassLoaderFor(JmxMBeanServer.java:1300)
at com.sun.jdmk.interceptor.DefaultMBeanServerInterceptor.getClassLoaderFor(DefaultMBeanServerInterceptor.java:285)
at com.sun.cacao.agent.DispatchInterceptor.getClassLoaderFor(DispatchInterceptor.java:548)
at com.sun.cacao.agent.auth.impl.AccessControlInterceptor.getClassLoaderFor(AccessControlInterceptor.java:427)
at com.sun.jdmk.JdmkMBeanServerImpl.getClassLoaderFor(JdmkMBeanServerImpl.java:1130)
at com.sun.cacao.common.instrum.impl.InstrumDefaultForwarder.getClassLoaderFor(InstrumDefaultForwarder.java:153)
at javax.management.remote.rmi.RMIConnectionImpl$4.run(RMIConnectionImpl.java:1308)
at java.security.AccessController.doPrivileged(Native Method)
at javax.management.remote.rmi.RMIConnectionImpl.getClassLoaderFor(RMIConnectionImpl.java:1305)
at javax.management.remote.rmi.RMIConnectionImpl.invoke(RMIConnectionImpl.java:768)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:585)
at sun.rmi.server.UnicastServerRef.dispatch(UnicastServerRef.java:294)
at sun.rmi.transport.Transport$1.run(Transport.java:153)
at java.security.AccessController.doPrivileged(Native Method)
at sun.rmi.transport.Transport.serviceCall(Transport.java:149)
at sun.rmi.transport.tcp.TCPTransport.handleMessages(TCPTransport.java:466)
at sun.rmi.transport.tcp.TCPTransport$ConnectionHandler.run(TCPTransport.java:707)
at java.lang.Thread.run(Thread.java:595)
at sun.rmi.transport.StreamRemoteCall.exceptionReceivedFromServer(StreamRemoteCall.java:247)
at sun.rmi.transport.StreamRemoteCall.executeCall(StreamRemoteCall.java:223)
at sun.rmi.server.UnicastRef.invoke(UnicastRef.java:126)
at com.sun.jmx.remote.internal.PRef.invoke(Unknown Source)
at javax.management.remote.rmi.RMIConnectionImpl_Stub.invoke(Unknown Source)
at javax.management.remote.rmi.RMIConnector$RemoteMBeanServerConnection.invoke(RMIConnector.java:972)
at javax.management.MBeanServerInvocationHandler.invoke(MBeanServerInvocationHandler.java:201)
... 39 moreWell,
The problem was a Memory problem: The swap file was misconfigured. Once the system reboots with the correct swap configuration I was able to register the machine.
Anyway, the problem to connect with SunSolve is continous, but it is other point of discussion.
I hope this solution can help people with similar problems.
H. -
SQL Server: 2008 R2 SP2
Before describing my problem, I have gone via the forum, there is no view or functions inside my stored procedure
When running a particular stored procedure inside crystal report, the error " Could not continue scan with nolock due to data movement" comes once every few weeks. After I clear the query cache plan, it works again for few weeks and the problem
comes again. During these few weeks, there is no restart or query plan clearing.
If I run the stored procedure inside SSMS, where the SQL statement is copied and pasted from SQL profiler during crystal report run, there is no error.
I discovered running in SSMS and crystal report generate 2 different query plans even I copied the SQL from SQL profiler, I have actually saved the query plans. Unfortunately, this forum does not accept attachments, or otherwise I will post my query plans
here.
There is one thing I notice about the query plan is during nested loop operation, there is a warning "no join predicate". I don't use any views or UDF in the statement, nor did I use pre-1992 ANSI join syntax. However, I did use table variables.
My guess is whether this will cause " Could not continue scan with nolock due to data movement", after I clear the cache, I run crystal report again, and I look at the plan again, the "nested loop no join predicate" warning is gone.
Running this stored procedure took 1 second maximum, even when this error is popping up, it pop up within 1 second.
DBCC checkdb has been run
The same stored procedure running by crystal report in a SQL 2008 (non r2) live environment has no problems, so I am thinking this is R2 specific problems.
The "nested loop no join predicate" error SQL statment is below, no views, no udf, but table variables
INSERT @ChequeAccount
SELECT PS.PaySummaryID, PS.EmployeeID, PS.CostCentreID,
(PS.GrossPay + PS.LumpSumA + PS.LumpSumB + PS.LumpSumD+ PS.LumpSumE+ PS.ETP+ PS.PaymentsAfterTax - PS.DeductionsAfterTax
- PS.Tax- PS.ETPTax + PS.TaxRebate) * -1 AS Amount,
CGLM.GLAccountID
FROM Pay_Summary PS JOIN Input_Sheet ISH ON PS.InputSheetID = ISH.InputSheetID AND ISH.PayrollID = @binPayrollID
AND PS.PaySummaryID NOT IN (SELECT PaySummaryID FROM @ChequeAccount)
JOIN Payroll P ON P.PayrollID = ISH.PayrollID AND P.EmployerID = @binEmployerID
JOIN CustomGLFixMapping CGLM ON CGLM.EmployerID = P.EmployerID AND CustomGLFixMappingNameID = 1 AND CGLM.CostCentreID IS NULLThe error Could not continue scan with nolock due to data movement can occur when you use the NOLOCK table hint, or use the command SET TRANSACTION ISOLATION LEVEL READ UNCOMMITTED. That is, so-called dirty reads. The error is not related to the
query plan per se, but when scanning a table, the storage engine will use an IAM scan rather than following the clustered index. If there is simultaneous activity, the storage engine may detect this and abort the operation to avoid returning incorrect data.
Or it may not detect it, and return uncommitted data or fail to return committed data.
All of these effects are transitory and they will not show up when you are alone on the system, only when there is concurrent activity in one or more of the tables in the query.
Using dirty reads is a risky business for the reasons explained above, and it takes careful analysis to understand whether you can live with the errors you can get from a particular query. The error about data movement can be handled: trap the error and
resubmit the query. But what about spurious incorrect results?
If you believe locking to be a problem, you should consider setting the database to READ_COMMITTED_SNAPSHOT
and take out all use of READ UNCOMMITTED/NOLOCK. When the database is in READ_COMMITTED_SNAPSHOT, readers read from the snapshot and only see committed data without blocking writers. This has some other effects like requiring a bigger tempdb,
and there is a risk for other types of concurrency errors, but they tend to be smaller risks.
I discovered running in SSMS and crystal report generate 2 different query plans even I copied the SQL from SQL profiler,
This is because SSMS by default runs with SET ARITHABORT ON. I discuss this in more detail in this article on my web site:
http://www.sommarskog.se/query-plan-mysteries.html
However, as I said, this problem is not related to the query plan as such, although some query plans are more susceptible to this error than others. (All plans are suscpeitble to produce incorrect results).
Erland Sommarskog, SQL Server MVP, [email protected]
Maybe you are looking for
-
How can I upload my old text messages to Integrated Messaging?
I recently started using Verizon Integrated Messaging around a month ago and am now upgrading my phone (that has text messages for the last two years). Normally I could just take all my texts and send them, Android to Android via Verizon Cloud or a
-
Apps are not being transferred after updating to new iOS
I've read a few posts but nothing explicitly about this issue. I am the original account owner, same computer, iPod has worked with the same apps for over a year until I updated to the new iOS a few days ago. I recently updated my iPod Touch to the n
-
21" iMac G4 running slower and s l o w e r....
This machine is running increasingly slowly, regardless of which applications are or aren't running. I'm continually seeing the spinning beachball, and it feels like there is some incredibly cycle-consuming thing going on in the background but I can'
-
I'm a newbie just working on the Adobe Dreamweaver tutorial. It instructs me to go to modify>page properties> click on the background color box and select black (#000000). I did this and the background color is still without color. When I open the pa
-
Error when installing 'Oracle Service Registry' .
D:\SOA\stage\ServiceRegistry>java -jar oracle-service-registry-10.1.3.1.jar Exception in thread "main" java.lang.UnsupportedClassVersionError: com/systinet/ uddi/tools/InstallTool (Unsupported major.minor version 48.0) at java.lang.ClassLoader.define