Errors with a TDS 1012 scope

Hello,
I am having probelms with the example for the TDS 1012 scope that I got from the NI website. I have installed the drivers on the PC and I have assumed that that is all I need to do to have the example work. I have attached a screen shoot of the error(s) that I am getting.
Regards
Kaspar
Regards,
Kaspar
Attachments:
TDS-1012_example error.pdf ‏191 KB

Hello,
   Ok, now I feel that I am starting to get somewhere. I have disconnected the scope probe from channel one of the scope, therefore there is no signal going to the scope, obviously no edge is presented to the scope, the scope therefore does not get triggered and no waveform should come out of the scope...but it does....why?
So if you run the edge example vi no errors come out of any vi and a waveform appears on the front panel.
   I initially thought that the timeout value was used to determine the duration that the read vi would wait until a edge ocurred on the scope input, which trigers the scope and then a waveform is generated by the scope and sent to the labview program. . It appears that the timeout value is only used to allow sufficient time for the waveform data to come out of the scope.
So why is a waveform being display on the front panel without any errors being generated when no trigger has been sent to the scope?
Regards
Kaspar
Regards,
Kaspar

Similar Messages

What deterimes the amount of data in a waveform from a TDS 1012 scope

Hello,
   What determines the amount of data that is in a waveform that comes out of a TDS 1012 scope? I am assuming that I will have to look at the driver vi to determine the commands sent to the scope to figure it out. I am in a situation that I need to have the y axis to have a high resolution, that results in very little data being collected from the scope.
Regards,
Kaspar
Regards,
Kaspar

Hello,
    The amount of data that comes out of the TDS 1012 scope is determined by the data start (DATaTARt)  and data stop (DATaTOP)  commands that are defined on page 58 (2-38) in the 346 page programming manual for the scope. I found of that the data start was not set to 1, which is the beginning of the data.
    I also had a very low level signal on channel that was all most unreadable by the scope that caused me to think that I was not getting all of the data.
Regards,
Kaspar
Regards,
Kaspar

No way to publish a workflow, I get this error: System.InvalidOperationException: Operation failed with error Microsoft.Workflow.Client.ScopeInactiveException: Scope ... is not in an active state. Its current state is 'Unregistering'

Hi,
I'm using Project Server 2013 and I'm not able to publish a workflow in SharePoint Designer 2013, I get this error:
System.InvalidOperationException: Operation failed with error Microsoft.Workflow.Client.ScopeInactiveException: Scope '/SharePoint/default/d7feb9ea-ccb2-4ec3-8f89-2a45b6cf3777' is not in an active state. Its current
state is 'Unregistering'. HTTP headers received from the server - ActivityId: c47ef567-8c54-4ae0-9a1a-1e4fb51320d8. NodeId: TestServer. Scope: /SharePoint/default/d7feb9ea-ccb2-4ec3-8f89-2a45b6cf3777. Client ActivityId : c6e5979c-20f8-e042-1f9d-2cb2a25d7f9e.
---> System.Net.WebExceptio
The thing is that I transferred the databases from a Prod.Env. to the Test Env. and from that moment on the Test Env. stopped working (only workflows), then I
was thinking that maybe the workflow is not working in the Test Environment because when I transferred the databases from Prod Env to Test Env I didn’t transfer the databases related to workflow, I only transferred:
WSS_Content
PWA_ServiceDB
But I didn’t transfer:
SBGatewayDatabase
SBManagementDB
SBMessageContainer01
WFInstanceManagementDB
WFManagementDB
WFResourceManagementDB
I didn’t transfer them because, before, when I transferred DB’s in version 2010, these DB’s were not needed, as the workflows were done using another method.
So, I tried to create a new workflow in the Test Env. but there is no way, I always get that error.
I've tried to Register again the workflow, and the result looks ok, but it doesn't solve the problem:
Register-SPWorkflowService
–SPSite "http://whatever/PWA"
–WorkflowHostUri "http://TestServer:12291"
–AllowOAuthHttp -Force
Do you know how to solve this issue or have an idea to give me some light?
Thank you for your help and regards,
José Espases

Looks like you haven't defined the WF scope or the site where you are trying to deploy the workflow to isn't included in the scope
Check this article
http://fangdahai.blogspot.in/2013/04/on-premise-windows-workflow-server.html
Thanks | epmXperts | http://epmxperts.wordpress.com

Service request error with TDS3034B Scope

Hello,
I am getting an error with a service request when initializing my oscilloscope. When I use the VISA Discard Events vi, there is an error 1073676292 that says
VISA: (Hex 0x3FFF0004) Operation completed successfully, but queue was already empty.
However, immediately after, I use VISA Enable Event and get an error 1073676290 that says
VISA: (Hex 0x3FFF0002) Specified event is already enabled for at least one of the specified mechanisms.
Both Discard and Enable Events are Service Request, so I am unsure why it would read that there is an empty queue, and then afterwards read that the Service Request is already enabled.
Thank you for any help you may be able to give on the subject.

Hello,
Has the event already been enabled before this? I believe it will stay enabled until the VISA Disable Event VI is called, and not the VISA Discard Events VI.
Regards,

Using a lookup from one CSV file to another CSV file errors with a name clash

Hi
I have a master CSV file created by querying the AD. I need to populate the "Team" attribute by doing a lookup using Name against the Name Column any of 6 CSVs, someone has prepared for me . The problem is the data is inconsistent
in the 6 CSV files so Name can hold either the Name or Username i.e. SAmAccountName or LoginName
Now my ps script works when the data is good. but I have around 30 exception cases whereby there is a mismatch . To explain:
is in this line ( see the big code block below)
$userObject = $nameAndTeamCsvData | Where-Object {$_.Name -eq $masterUserName}
The $_.Name is using the top level masterCSVData Name but I was hoping that it was using the
$nameAndTeamCSVData.Name as in only within the scope of the Where-Object {} ..I guess I have misunderstood the syntax of what I had written.
. A quick a dirty fix would be rename this column in all of the 4 spreadsheets or trying to fix the code.....
# now update the empty team value for user object
$csvMasterData | ForEach-Object `
$masterName = $_.Name
$masterUserName = $_.Username # to deal with exception cases
#force scope to as the properties in the outer with the same name should be out of scope
# lookup the Name to see if we can extract the user's Team
$userObject = $nameAndTeamCsvData | Where-Object {$_.Name -eq $masterName }
# deal with the situation where the name in the businesses spreadsheets is actually the Username (login name) in the master csv
if ( $userObject -eq $null )
# lookup the username (loginname) to see if we can extract the user's Team # !!!!error occurs here with the $_.Name !!!!!
$userObject = $nameAndTeamCsvData | Where-Object {$_.Name -eq $masterUserName}
if ( $userObject -eq $null )
$_.Team = "UNKNOWN"
else
# replace the mastercsv.Team with the one we have looked up
$_.Team = $userObject.Team
else
# Name matches so replace the mastercsv.Team with the one we have looked up
$_.Team = $userObject.Team
Daniel

I see your challenge. How about collecting the column names in an array and looking for the potential names? Following my example before, try this:
$dataColumns = $I | Get-Member -MemberType NoteProperty | Select-Object -ExpandProperty Name
Now, you can loop through the names and collect the appropriate data.
if ($dataColumns.Contains('Column1'))
#add ForEach-Object { $_.Column1... }
HTH
~fr3dd
Hi I had to wait until Friday as I have someone ( my boss) checking the business & team csv files against valid usernames and names.
# now update the empty team value for user object
$nameAndTeamCsvData | ForEach-Object `
$nt_name = $_.Name
# $masterUserName = $_.Username # to deal with exception cases
# lookup the Name to see if we can extract the username and mobile from the masterCSV
$userObject = $null # Replace my original code: $csvMasterData | Where-Object {$_.SName -eq $nt_name } # with foreach code below
$uo = $null
foreach ($uo in $csvMasterData)
if ($uo.SName -eq $nt_name)
$userObject = $uo
# ouch can't break out of this even though I found it so have to move on to the next
}if ( $userObject -ne $null ){ # Name matches so replace the few propeerties in mastercsv.Team with the ones we have looked up
$_.Username =$userObject.SamAccountName
$_.Mobile =$userObject.Mobile
This does work but is clearly not very efficient since I don't think I can
break or exit out of the foreach loop. I am thinking I could quickly modify and add your code - my import is delayed as I am having a new property added to user class... Let me know what you think.

Error with Script logic

Hello friends,
I am getting an error with running currency conversion in an app, the error says Invalid dimension "C_Category". Here is the script logic, I dont see C_Category anywhere. For the record, the name of dimension is category.
*RUN_PROGRAM CURR_CONVERSION
      CATEGORY     = %C_CATEGORY_SET%
      GROUP = %GROUPS_SET%
      TID_RA = %TIME_SET%
      RATEENTITY = GLOBAL
      OTHER = [ENTITY=%ENTITY_SET%]//For More than one other scope parameters: OTHER = [ENTITY=%ENTITY_SET%;INTCO=%INTCO_SET%...]
*ENDRUN_PROGRAM

Hello,
Variable %C_CATEGORY_SET% means set of members selected for Dimension C_CATEGORY. So, if you want to use CATEGORY instead replace it with %CATEGORY_SET%, but if are running Consolidations I think you need C_CATEGORY Dimension.
Regards,
Gersh

Spring framework - Error with session scoped Beans

Hello guys,
I'm trying execute my Java Application inside Netweaver Application Server, but I'm having problems with serviceBeans with scope session. Anyone have already used Spring with session scope?
Thanks,
Cleiton.

After many attempt, when I declared the bean with <aop:scoped-proxy /> it works, however it could cause performance problem. I don't need refer this bean by another singleton bean, i did a wrong configuration in order to make a work a round...
When I run my application on tomcat server, the DWR starts perfectly the "session scope bean form IOC container", but in the WEBAS maybe it's running in other thread. Is it possible?
Anyone had a problem like this?
I got a detailed error with log4j,
ERROR Application [1] org.directwebremoting.impl.DefaultCreatorManager - Error loading class for creator 'SpringCreator[CounterSpringFacade]'.
org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'counterSpringFacade': Scope 'session' is not active for the current thread; consider defining a scoped proxy for this bean if you intend to refer to it from a singleton; nested exception is java.lang.IllegalStateException: No thread-bound request found: Are you referring to request attributes outside of an actual web request, or processing a request outside of the originally receiving thread? If you are actually operating within a web request and still receive this message, your code is probably running outside of DispatcherServlet/DispatcherPortlet: In this case, use RequestContextListener or RequestContextFilter to expose the current request.
     at org.springframework.beans.factory.support.AbstractBeanFactory.doGetBean(AbstractBeanFactory.java:312)
     at org.springframework.beans.factory.support.AbstractBeanFactory.getBean(AbstractBeanFactory.java:185)
     at org.springframework.beans.factory.support.AbstractBeanFactory.getBean(AbstractBeanFactory.java:164)
     at org.springframework.context.support.AbstractApplicationContext.getBean(AbstractApplicationContext.java:881)
     at org.directwebremoting.spring.SpringCreator.getInstance(SpringCreator.java:145)
     at org.directwebremoting.spring.SpringCreator.getType(SpringCreator.java:107)
Edited by: Cleiton dos Santos Garcia on Jan 7, 2009 5:02 PM

ScriptProtect error replacing insecure tag in scope CGI

I am getting the ScriptProtect error replacing insecure tag in scope CGI error. This was brought up two other times in the history of the forum. Additionally it has not been truly addressed over the web. The problem that I am having is that the way that this is being addressed is very cursory. We all know that this can happen when ScriptProtect=all is turned on in the <cfapplication tag. The problem is that this is not related to the lib/neo-security.xml file. It can be resolved by removing the scriptprotect attribute, but we need this attribute for help with XSS attacks. I am running this on our site and though that it could have been something that I was passing in the URL but that is not the case. In fact, after removing all of the querystring and just calling the website directly after receiving that error. The error persists. It doesn't go away until I refresh the home page, close my browser or clear my cache.
The problem remains that when I go to a page, and pass certain values (which are not XSS related) and are not filitered out with the lib/neo-security.xml file I still get this error. Where is this error generated? Why does it reference the CGI scope of all things? How can this be resolved without removing the scriptprotect attribute?
Sincerely,
Braden Lake

Braden Lake wrote:
Does anybody have an answer to this?
Nope.
Answer to what? What error did you actually get?
The only insight I can give is to why the cgi scope maybe called. The CGI scope includes date provide to the web server by the browser and is just as vulnerable to XSS modification by hackers as GET and POST data. Infact cgi.query_string is a copy of any GET date provided as URL parametes.

RE: [Adobe Reader] when i open pdf file it open all the pages but some pages give error massage (there was error processing a page,there was a problem reading this document 110) but if i open this page which give me error with google chrome it's work ? i

HelloThank's for your helpsI hope this document is helpfulBest Regards,
Date: Sun, 22 Jun 2014 17:10:17 -0700
From: [email protected]
To: [email protected]
Subject: when i open pdf file it open all the pages but some pages give error massage (there was error processing a page,there was a problem reading this document 110) but if i open this page which give me error with google chrome it's work ? if you can help me th
    when i open pdf file it open all the pages but some pages give error massage (there was error processing a page,there was a problem reading this document 110) but if i open this page which give me error with google chrome it's work ? if you can help m
    created by Anoop9178 in Adobe Reader - View the full discussion
Hi,
Would it be possible for you to share the document?
Regards,
Anoop
     Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at https://forums.adobe.com/message/6485431#6485431
     Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
     To unsubscribe from this thread, please visit the message page at . In the Actions box on the right, click the Stop Email Notifications link.
     Start a new discussion in Adobe Reader by email or at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

thank's for reply and your help
i did the step's that you told me but i still have the same problem
                                 i have the latest v.11.0.7
i
i disable the protected mode

Odd Error with decode function in Order By Clause

I am trying to compile a procedure and can't get around an error with a dynamic order by that doesn't make much sense to me. I can repoduce the error with a plain select statment in sql plus so I can rule out a declaration error. Here is an example with 2 numeric columns and a date column.
select task_id, display_date, remark_id from task_list
where task_id > 1000
order by decode('Task_ID', 'Task_ID',Task_ID, 'Display_Date', Display_Date, 'Remark_ID',Remark_ID)
returns the error:
select task_id, display_date, remark_id from task_list
ERROR at line 1:
ORA-00932: inconsistent datatypes: expected NUMBER got DATE
I'm not sure why this error is occuring, because it doesn't even hit the Display_Date field in the Decode statment. If I take the Display_date out of the statement, it runs properly. If I change Display_Date to To_Char(Display_Date) it also runs fine, but the sorting is incorrect. Also I'm running 9.2, and do not want to use dynamic sql to build my query. Any Ideas out there as to the cause of this error?

I did find a workaround to this issue by breaking the decode statment into three separate statement, but I still think that the way it is written above should work, and may be a bug, or an error that I don't understand fully.
The Order by was rewritten like this:
order by decode(pSort, 'Task_ID',Task_ID), decode(pSort, 'Display_Date', Display_Date),
decode(pSort, 'Remark_ID',Remark_ID);
Thanks

XML Publisher Error with reports published in XML publisher

Hi All,
I am geting the following error with a report published using XML Publisher
The XML page cannot be displayed
Cannot view XML input using style sheet. Please correct the error and then click the Refresh button, or try again later.
The system cannot locate the resource specified. Error processing resource 'http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.d...
How can i Rectify this?

Hi Ark,
In order to generate a report using xml publisher. we need the following.
1. XML Data
2. Template file (RTF/PDF/..)
XML data will not be created by the template file.
We will be required to create XML data. One of the easiest way to create xml output is using the RDF. We can change the rdf output type in the concurrent program to XML.
Once the xml and the template is available, "XML Report Publisher" will be able to generate the output in the required format.
Thanks,
K.Nataraja Suthan,

Graphic problems/errors with Mainstage 3 and MBP (15'' 2011)

Hi,
I bought Mainstage 3 for my MBP (15'' 2011).
When i click con "perform" i get graphic errors.
I have the same issue with the old Mainstage version since Mountain Lion.
Also a fresh installation didn't help.
I think i'm not the only one with this issue!
I don't know how to report a bug?
Perhaps someone can help me.
(and I'm probably not the only one (see feedback in Apple Store) If you also have this problem, please add a comment with your configuration (Hardware, Software))
/forgotten ebi
So, here an example how it looks like when i click on "perform":

Same configuration,same problem. BUT I found a workaround.
Mainstage has this error with the AMD video card and/or a second monitor connected.
With a little app (http://gfx.io) it's possible to really force the MBPro to use the Intel Graphics card.
This will work only with the internal screen, not with a second screen connected.
And sometimes you need to restart, to really make the Intel video card free.
This works fine...In the meantime of a fix.

Error with an infoset in BI

HI BI gurus,
we have a problem with an infoset.
We create an infoset in RSA1 linked to a cube and a DSO.
We activate it in english without problems and I can create a query with no errors (with a english logon).
If I try to create a query in italian language the query designer show mw this error: " unexpected error - RCF_SYSTEM_FAILURE. You must restart the query designer."
Do you have any idea how to fix and solve this problem? We try to activete the infoset in Italian but the error remains.
Thanks for any help.
SB

Hi,
is italien installed as a language in your system?
Siggi

I am trying to download my photos from my iphone to my mac-iphoto. It keeps trying but about halfway through it says there is an error with a photo therefore it wont download any of my pictures or videos. It wont tell me which picture is the issue.

I took a lot of pictures and video on my recent trip to Ireland. Now I am trying to download the photos and videos from my iphone to my mac - iphoto. I have tried 3 times and each time (at a different point) I get a message telling me that there was an error with one of my photos and it wont load the pictures. Help!!

Try using Image Capture to download to a folder on the Desktop. If there's a damaged file on the iPhone that's preventing the download you can isolate it with Image Capture and then delete it from the iPhone.

Plug-in errors and dependency errors with a CAF app in DS in NW CE 7.1

I am learining to build CAF apps in Developer Studio in NW CE 7.1. Here are my steps and the errors I am getting:
Open Developer Studio
Switch to the CA perspective
File->New->Project
Choose Development Component under Development Infrastructure
Press Next
Choose Composite Application under sap.com
Choose MyComponents[demo.sap.com] under 'Local Development'
Vendor: demo.sap.com
Name: carpool
Caption: Car Pool
Language: American English
Domain: SAP-xApps
Support Component: CAF-APP (typed in, not chosen)
Press Finish
The following error appears:
Status ERROR
Plugin : com.sap.ide.metamodel.core.services.eclipse
code=0
Internal error
   Plugin name: Metamodel Core
   Internal error : com.sap.ide.metamodel.core.services.eclipse
   Class      : com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker
   Method     : computeIdeJarProperties
   Message    : C:\Program Files\SAP\IDE\CE\eclipse\E:\Program Files\SAP\IDE\CE\eclipse\plugins\com.sap.dictionary.services_10.0.0.070821165456\lib\com.sap.dictionary.services_api.jar (The filename, directory name, or volume label syntax is incorrect)
   Exception : java.io.FileNotFoundException: C:\Program Files\SAP\IDE\CE\eclipse\E:\Program Files\SAP\IDE\CE\eclipse\plugins\com.sap.dictionary.services_10.0.0.070821165456\lib\com.sap.dictionary.services_api.jar (The filename, directory name, or volume label syntax is incorrect)
java.io.FileNotFoundException: C:\Program Files\SAP\IDE\CE\eclipse\E:\Program Files\SAP\IDE\CE\eclipse\plugins\com.sap.dictionary.services_10.0.0.070821165456\lib\com.sap.dictionary.services_api.jar (The filename, directory name, or volume label syntax is incorrect)
at java.util.zip.ZipFile.open(Native Method)
at java.util.zip.ZipFile.<init>(ZipFile.java:203)
at java.util.jar.JarFile.<init>(JarFile.java:132)
at java.util.jar.JarFile.<init>(JarFile.java:70)
at com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker.computeIdeJarProperties(ArchiveVersionChecker.java:296)
at com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker.doFullCheck(ArchiveVersionChecker.java:214)
at com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker.checkProject(ArchiveVersionChecker.java:125)
at com.sap.ide.mmservices.core.eclipse.generation.GenerationServiceEclipse.checkArchiveVersions(GenerationServiceEclipse.java:110)
at com.sap.dictionary.tools.generation.eclipse.GenerationBuilder.checkArchiveVersions(GenerationBuilder.java:335)
at com.sap.dictionary.tools.generation.eclipse.GenerationBuilder.build(GenerationBuilder.java:85)
at org.eclipse.core.internal.events.BuildManager$2.run(BuildManager.java:624)
at org.eclipse.core.runtime.SafeRunner.run(SafeRunner.java:37)
at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:166)
at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:197)
at org.eclipse.core.internal.events.BuildManager$1.run(BuildManager.java:246)
at org.eclipse.core.runtime.SafeRunner.run(SafeRunner.java:37)
at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:249)
at org.eclipse.core.internal.events.BuildManager.basicBuildLoop(BuildManager.java:302)
at org.eclipse.core.internal.events.BuildManager.build(BuildManager.java:334)
at org.eclipse.core.internal.events.AutoBuildJob.doBuild(AutoBuildJob.java:137)
at org.eclipse.core.internal.events.AutoBuildJob.run(AutoBuildJob.java:235)
at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55)
I do not think I missed anything installing NW CE 7.1, but this error makes me think that some plug-in was erroneously left out of the install.
Incidentally, I can continue onward and build an app (this is obviously a tutorial), but when I try to deploy I get the following error:
The deployment of the archive failed with an exception!
([ERROR CODE DPL.DCAPI.1027]) DependenciesResolvingException.
Reason:[ERROR CODE DPL.DC.3033] An unresolved dependencies error
occurred while sorting the deployment batch items regarding the
dependencies.;nested exception is:
com.sap.engine.services.dc.cm.deploy.sdu_deps_resolver.UnresolvedDepen
denciesException:[ERROR CODE DPL.DC.3437]Unresolved dependencies
found for the following deployment items:
1. Component: name:'carpool~ear',vendor:'my.company',location:
'localDevelopment',version:'20080501110329',software type: 'J2EE',
dependencies:'[name:'cafruntimeear',vendor:'sap.com',name:
'cafcoreear',vendor:'sap.com']
Unresolved dependency:
name:'cafruntimeear',vendor:'sap.com'          (not found in the admitted
batch items and the repository)
Unresolved dependency:
name:'cafcoreear',vendor:'sap.com'          (not found in the admitted
batch items and the repository)
Please check the error log for further informations.
Again, this looks like I am missing some components.
Any assistance is greatly appreciated.
TB

Further developments: As you may note from the error message, DS is looking for com.sap.ide.metamodel.core.services.eclipse in both the C: and the E: drive at the same time. In fact, this file exists in the E: drive subdirectory listed, so I obviously have an error with two drive designations being concatenated. Does anyone know how I can change the lookup directory for this dependency (or any dependency)?
Thanks,
TB

Errors with a TDS 1012 scope

Similar Messages

Maybe you are looking for