Exchange Queue issues

Hi
we have 2 Exchange 2010 servers out of which one has a Mail Queue issue.
whenever we view queue viewer through console or through shell with Get-queue, we get error like "Exchange can't connect to the mail queue check the transport service is started"
If i refresh couple of times, it shows the queue on both. This happens frequently.
I recreated a new Mail queue but still same error.
During this error, the Transport service never stops and it shows as Started always. We have restarted this service and restarted the server twice. No improvement.
was there anything to be checked?
regards Sundaresan.C

Hi sun,
Thank you for your question.
Which roles has been installed on 2 Exchange server?
If CAS and Hub are not on same server:
Make sure CAS server connect to Hub without any network issue, we could check if there are any IP data packet which are missing between CAS and Hub.
Make sure the transport service are running when we get error on CAS and Hub.
Check if CAS and Hub are same version(include CU)
If CAS and Hub are the same server, we could check event log when we get error when we run the command. You could send the relevant log to
[email protected] for our troubleshooting.
We could try to rename the queue folder to check if the issue persist.
If there are any questions regarding this issue, please be free to let me know.
Best Regard,
Jim

Similar Messages

  • Checklist for Exchange Certificate issues

    Checklist for Exchange Certificate issues
    1. 
    Why certificate is important for Exchange and What are Certificates used for
    Exchange is now using certificates for more than just web, POP3, or IMAP. In addition to
    securing web services, it has also incorporated Transport Layer Security (TLS) for session based authentication and encryption.
    Certificates are used for several things on Exchange Server. Most customers also use certificates
    on more than one Exchange server. In general, the fewer certificates you have, the easier certificate management becomes.
    IIS (OWA, ECP, EWS, EAS, OA, Autodiscover, OAB, UM)
    POP/IMAP
    SMTP
     2. 
    Common symptoms for
    certificate issue
    Here we can see three different types of the certificate warning, mainly from the Outlook
    side.
    a.
    Certificate mismatch issue
    b.
    Certificate trust issue
    c.
    Certificate expiration issue
    3. 
    Checklists
    In this section, checklists will be provided according to the three different scenarios:
    Certificate Mismatch Issue
    [Analysis]:
    This issue mainly occurs because the URL of the web services Outlook tries
    to connect does not match the host name in the certificate.
    [Checklist]:
    Firstly make sure how many host name in your certificate the certificate. Run “Get-ExchangeCertificate | select certificatedomain”.
    Secondly, check the web services URLs which Outlook are trying to connect to. Run “Test Email AutoConfiguration”
    In this scenario, you need to check the host name for the following services:
    Autodiscover
    EWS
    OAB
    ECP
    UM
    If any of the urls above does not match the one in the certificate, refer to the following article to change
    it via EMS:
    http://support.microsoft.com/kb/940726
     1.
    Do not forget to restart the IIS service after applying the changes above.
     2. Make sure a valid certificate is enabled on the IIS service.
    Certificate Trust Issue
    [Analysis]:
    For the self-signed and PKI-based (Enterprise)
    certificates, they are not automatically trusted by the client computer or mobile device, you must make sure that you import the certificate into the trusted root certificate store on client computers and devices. On the other hand, Third-party or commercial
    certificates do not have this problem. Most commercial CA certificates are already trusted because the certificate already resides in the trusted root certificate store. Because the issuer is trusted, the certificate is also trusted. Using third-party certificates
    greatly simplifies deployment.
    [Checklist]:
    If it’s an Enterprise CA certificate, manually install the root certificate to the “Trusted Root Certification Authorities” folder:
    If it is a 3<sup>rd</sup>-party certificate, first remove and reinstall the certificate. Check whether the Windows Certificate Store on the local
    client is corrupted. If it still does not work, please contact the third-party CA support to verify the certificate.
    Certificate Expiration Issue
    [Checklist]:
    When a certificate is about to expired, we just need to renew it by referring the following article:
    Renew an Exchange Certificate
    http://technet.microsoft.com/en-us/library/ee332322(v=exchg.141).aspx
    To avoid any conflictions, it’s recommended to remove the expired certificate from the certificate store.
    [How to set a reminder to alert the administrator when a certificate is about to expired]:
    It’s easy to fix the certificate expire issue. But it should be more important to set a reminder before the
    certificate expiration. Or there can be a large user impacts.
    Generally, the Event ID “^(24|25)$” will appear in Application log when a certificate is about to expire.
    If it’s not quite visible, we can refer to the following solution:
    http://blogs.technet.com/b/nexthop/archive/2011/11/18/certificate-expiration-alerting.aspx
    OWA certificate revoked issue
    [Analysis]:
    IE
    includes support for server certificate revocation which verifies that an issuing
    CA has not revoked a server certificate. This feature checks for CryptoAPI revocation when certificate extensions
    are present. If the URL for the revocation information is unresponsive, IE cancels the connection.
    [Solution or workaround]:
    1. Contact CA provider and check whether the questioned certificate is in the Revoked List.
    2. If not, check whether the certificate has a private key.
    3. Remove the old certificate and import the new one.
    Workaround:
    IE Internet Options -> Advanced tab -> Clear the "Check for server certificate revocation"
    checkbox.
    4. 
    More References
    Digital Certificates and SSL
    http://technet.microsoft.com/en-us/library/dd351044(v=exchg.150).aspx
    More on Exchange 2007 and certificates - with real world scenario
    http://blogs.technet.com/b/exchange/archive/2007/07/02/3403301.aspx

    (Reported previous post with link to SIS package to moderator)
    This is not the correct SIS package for the N73. The package shown is for S60 3.2 devices, but the N73 is not S60 3.2, I believe it is S60 3.0.
    Most features may work with this SIS, but if you experience strange problems, try using the S60 3.0 version.
    But there are no significant difference between 2.5.3 and 2.5.5 with regard to attachments. The only changes were with localization (languages).
    At this point, try 2.7.0 which is out now:
    http://businesssoftware.nokia.com/mail_for_exchange_downloads.php
    Make sure to pick the right phone on the drop down list. It does matter! There are 4 different packages. This list makes sure you get the right one.
    I have seen some issues with attachments not completing that seem to be carrier dependent. You can test this my using Wifi (if possible).
    Message Edited by m4e_team_k on 28-Sep-2008 12:25 AM

  • Exchange 2013 Issue: Outlook 2010 auto populating the From Tab when forwarding email

    Exchange 2013 Issue: Outlook 2010 auto populating the From Tab when forwarding email        
    I am running Exchange 2013 and I have an end user who connects to it via Outlook 2010. All was going well till he went to forward an email and he noticed that the From button appeared and auto populated the sender's email address.
    I have clicked the Empty Auto Complete List in Outlook's Send messages... still displayed the From tab when forwarding.
    I recreated the profile in outlook... same thing.
    I created the profile with outlook 2013... same thing.
    There is only one user profile setup in Outlook.
    (I know the from tab usually appears when you have multiple profiles setup in Outlook and/or when you configure the "From" tab.)
    I opened the end user's email in Exch 2013's OWA... what was different here was when I clicked on the email and it opened, it did NOT have the Reply or Forward option... and it displayed as a "Draft" email.
    Does anyone have any ideas?

    So are you saying that the from button is filling the option with the original senders address (eg the person who sent the message to your user), or that it's filling in the your users address (in which case I don't understand what the issue is, since
    it IS going from your user)?

  • Exchange Rate Issue ( Ditect & Indirect Quotation )

    Dear,
    Alll Experts.
    I am stuck up at one level , that is Exchange Rate issue.
    User is creating shopping cart in SRM, Local Currency is USD and the goods is ordering from Canada ( CAD ).
    While doing this amount is getting calculated   in - ( Negative ), And it is going to wrong approval for shopping cart approval.
    When I see the TCURR table I am seeing there as negative sign in exchange rate because it is maintained in Indirect Quotation.
    I want to calculate the same amount in postive figure.
    How this can be achieve? If I maintain the same in direct quotation it will calculate positive but final amount will be bigger which is not proper one.
    Experts guidance will be helpful.
    Regards,
    Sharvari Joshi.

    Hi,
    I gave the OB08 entries, not sure if you wanted me to explain the logic. Here it is..
    Maintain 'Indirect quotation' from Local currency(USD) to Transaction currency(CAD) and 'Direct quotation' from Transaction currency(CAD) to Local currency(USD).
    Direct quotation is where the cost of one unit of foreign currency is given in units of local currency, whereas indirect quotation is where the cost of one unit of local currency is given in units of foreign currency.
    Your local currency is USD:
    - Direct exchange rate: 1CAD = 0.92819 USD
    - Indirect exchange rate: 1USD = 1.08238 CAD
    The following settings have been made in the standard system:
      - Direct quotation: ' '
    -   Indirect quotation: ' / '
    Direct exchange rates do not have a prefix.
    Your local currency is USD. You enter a business transaction in the transaction currency CAD. Until now, you had to use direct quotation to enter the exchange rate (1CAD =0.92819 USD). If you have defined '/' as the prefix for indirect quotation, you can also enter the exchange rate with indirect quotation (1 USD = 1.08238 CAD) by entering '/1.08238' in the exchange rate field.
    Direct or indirect quotation can be maintained as the standard form of quotation for a certain currency pair. You use:
             - '1' for direct quotation
             - '2' for indirect quotation
    If a standard form of quotation has not been specified for a currency pair, the system automatically uses direct quotation.
    You make the settings in the IMG: General Settings -- Currencies -- Set Standard for Direct/Indirect Quotation per Currency Pair.
    Thanks
    Ganesh

  • Outlook with Exchange connection issues

    I am implementing a security policy which includes blocking all outbound traffic on the firewall of our network (Except normal 80, 443 etc). It seems
    that if I apply this, some users aren't able to connect to exchange. This appears to be related to Outlook Anywhere. What ports would I need to allow to prevent this connection issue?

    Hi
    As per the information and details provided by you, to solve the Outlook with Exchange connection issues, Please follow these steps: -
    Microsoft introduced
    RPC over HHTP as a better way for Outlook client to connect to Exchange. The MAPI connections still use RPCs, but they encapsulate those with an HTTP connection. Since that HTTP connection is secured using SSL, it is may be
    more accurate to call it RPC over HTTPS. These connections only require connectivity
    over TCP port 443, which as you know is assigned to HTTPS and is normally open by
    firewall admin for web servers.
    Outlook Anywhere wraps
    Remote Procedure Calls inside an HTTP layer to allow connectivity with the Exchange server. This simplifies the firewall administration process requiring only
    the SSL port 443 to be opened to the CAS (Client Access Server) instead of several ports to the actual Mailbox Server (MBX).
    I hope this information will be helpful for you.
    Thanks and regards
    Shweta@G 

  • The recent software update on my HTC One has caused errors with Exchange ActiveSync issues. Calendar, mail and tasks sync fine but contacts won't sync. How do you correct this?

    The recent software update on my HTC One has caused errors with Exchange ActiveSync issues. Calendar, mail and tasks sync fine but contacts won't sync. How do you correct this?

    I had the same problem.  Here is what worked for me.  Open the mail app and delete your exchange account (Settings > Delete Account).  Then re-add your Exchange account.  After this my Exchange contacts showed up again. 

  • Hp 3915. vista 32 "print queue issue" and i have to clear print queue and redo print.

    hp 3915.  vista 32 "print queue issue" and i have to clear print queue and redo print.  I think it may be a driver issue. Is there a driver for 3915 using Vista. Mine says only 2000 and XP. Thanks.

    Hi there ken4863,
    Try downloading and running the print and scan doctor located here:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03275041&cc=us&dlc=en&lc=en
    It can fix a lot on its own and if not give a better idea of what is going on.
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Exchange 2010 - Issues after rollup update installation.

    Exchange 2010 - Issues after rollup update installation.
    We are having issues since we installed SP3 Rollup updates 1, 2, 3, and 4.
    Issue1 - People get an error messages constantly popping up when they access our webmail. The error messages are:
    An unexpected error occurred and your request couldn't be handled. and
    Your network connection is unavailable. Please reconnect and try again.
    Issue2 - When I open the Exchange Management Shell I get the following error:
    Failed to connect to an Exchange server in the current site. Enter the server FQDN where you want to connect.
    Issue3 - We have been using third party software to filter spam email. It is installed on our Exchange server. Since the updates it has not been working and we have tons of spam coming through. I dont think that this issue is that important at the moment and
    hope that it will be fixed after resolving issues 1 and 2.
    We uninstalled all four rollup updates in hopes that everything would go back to normal but it hasnt. We still have the same issues.
    Currently we are running Exchange 2010 SP3 on 2008R2 SP1.
    Please help.
    Thanks.
    Greg

    Hi,
    Based on the description, you got the error below when you tried to accessed OWA after rollup update installation.
    "An unexpected error occurred and your request couldn't be handled, and Your network connection is unavailable. Please reconnect and try again."
    For this issue, I recommend you check the OWA virtual directory to see if "Redirect requests to this destination" is checked. If it is checked, please uncheck the option. Then please restart IIS service to check the result.
    Open IIS Manager -> owa -> HTTP Redirect -> uncheck "Redirect requests to this destination:"
    Best regards,
    Belinda
    Belinda Ma
    TechNet Community Support

  • Exchange 2013 issues - (new send email Stuck in Drafts not send)

    Exchange 2013 issues - (new send email Stuck in Drafts folder not send)

    I am also having this issue.
    server 2012 VM with exchange 2013. plenty of resources, more than recommended so cannot be a BAck Pressure issue especially as no clients are connected yet.
    In the early stages of setup and testing, mail sent to other mailboxes worked fine in outlook 2007 and OWA but after a few issue that developed and are now resolved, any e-mail send within outlook or OWA just goes straight into the drafts folder.
    I tried, DNS setting changes under roles, on the server, on DNS server, MX DNS records, increased resources, looked at received connectors, changed and even deleted send connectors as this is not required for internal mail. Tried changing authentication
    types but then outlook won't connect to, staying with Basic Auth.
    Have not been able to test inbound e-mail as this is going to replace a production server and is not ready, although I could probably simulate a route from another server and push e-mail to it. Will try tomorrow.
    I have spent about 20 hours trying to figure this out and made probably 40 changes. Change, test, rollback etc. Been searching through loads of forums and technet sites all with no help.
    All services are started, server has been rebooted several times.
    It is also an AD server and has both Exchange roles installed. There is no reason why it should not work. This is so frustrating, we don't have these issues with the now end of life Scalix, or MDaemon or Zimbra. Pity the client wanted a Microsoft solution.
    To be honest there are not a lot of things that cannot be changed in ECP although there is more under exchange powershell however I am not familiar with all the commands yet. I have resorted to watching training videos even though I am a seasoned IT Pro, although
    not so much with exchange it seems.
    I have seen many people have this issue on Exchange 2007, 2010 and 2013. Someone must know how to resolve this or find a work around?
    So far I have an expensive solution the client has purchased that I cannot get running properly.
    Aside from this issue, I really like the new Server 2012 and new Hyper-V.
    I was about to install Exchange Server 2013 on a physical machine due to this f#ckin' issue. But a post for the DNS change has saved my life:
    http://social.technet.microsoft.com/Forums/en-US/exchangeserverpreview/thread/04c0147b-f4e3-4041-a566-310854e71068/ (rafael9908's answer)
    And thanks Jesper Bernle for excellent info provided by your link.

  • Exchange sync issues

    I'm having an issue where my Exchange email seems to stop working on a random basis.  I have to delete my account and then re-add it in order to start receiving emails again.  My gmail and google apps accounts sync just fine.  I've checked with our IT department, and other users aren't having the same issue.  My phone worked fine up until about a week ago.  I deleted the certificate and re-installed it, just to be certain.  Any thoughts?  Any known issues I should be aware of?  Anyone else experiencing this problem?
    Thanks

    I'll have to check with the IT department.  Unless they have upgraded recently, we are using exchange 2003 SP1.  I'll also ask about the test account.
    As far as I know, and as far as IT knows, I'm the only one using WebOS.  The IT department only "supports" Blackberries & iPhones.  I prefer the Pre, and as long as the exchange sync works, I'll stick with it.
    I have had the issue happen again several more times.  It isn't an "8 am" exactly issue.  The other morning I received emails up until 9 or so, then stopped.
    I have tried just re-entering my password and that didn't seem to work.  Maybe I need to give it a little more time.  Maybe I should change my network password and see if that makes any difference.  Perhpas that is where the sync "disconnects".  Since exchange email works for iPhone users, I have to think it is a WebOS specific issue, versus an exchange issue, or perhaps I should say a WebOS - Exchange connection issue, as opposed to an "exchange" issue.
    I only asked about the logs because I was involved with a previous exchange sync issue and worked with the support techs several times, and they have asked for several logs.

  • Delivery delayed possibly because of Exchange Online issue with DNS check

    http://social.technet.microsoft.com/Forums/exchange/en-US/newthread?category=microsoftonlineservices&forum=onlineservicesexchange
    I'm troubleshooting extremely late (3+ days) delivery emails FROM a domain hosted by Microsoft TO systemid.com.  Microsoft Remote connectivity analyzer
    https://testconnectivity.microsoft.com/ shows that it cannot get MX record for systemid.com.  HOWEVER, other tools like Mxtoolbox (http://mxtoolbox.com/) shows the
    MX lookup is successful.
    When sending FROM Google / Yahoo to the same email address at systemid.com, the emails go through right away.
    I was able to reproduce the issue by sending an email FROM my personal Hotmail email to systemid.com.  The next morning I got a delayed Delivery Status Notifcation:
    Reporting-MTA: dns;BAY004-OMC1S14.hotmail.com
    Received-From-MTA: dns;BAY169-W65
    Arrival-Date: Tue, 30 Sep 2014 11:38:10 -0700
    Final-Recipient: rfc822;[email protected]
    Action: delayed
    Status: 4.4.7
    Will-Retry-Until: Thu, 2 Oct 2014 11:38:17 -0700
    I think the root issue is that Exchange Online does not like something about MX record for systemid.com, although other tools say the MX records are fine.
    Can you see why emails from Hotmail or one of your Exchange Online customers cannot reach systemid.com although emails from Google / Yahoo go in just fine?  Please PM me if you need the name of the domain hosted by Microsoft or an email address at systemid.com
    for testing.

    If you open a service request via your O365 tenant, and explain the issue, they'll respond quite quickly.
    I've created some tickets at O365 support for about the same problems in the past, and you usually get a call from an EOP/EO engineer the day after.

  • Exchange 2013 Issue - Cannot open default email folders. you must connect to microsoft exchange

    Hello all, this is my first post and nightmare to this issue because i believe i made mistake and overlook something. I search over the internet i cant find the best answer or maybe i missed something during the configurations. The exchange was working fine
    not after i change the setting following the method
    Configure External and Internal URL in Exchange 2012. after that, the users outlook experiencing disconnect from exchange. I restore back the previous setting but now I cant add any new user to the any Outlook version or change the server path. it will
    cause the problem which show the message below:
    "Can't open your default e-mail folders. You must connect to Microsoft Exchange with the current profile before you can synchronize your folder with your offline folders with your Outlook data file (.ost)"
    I restarted the server and check all the Exchange services are running. The Outlook web is running and they able to receive and send out. The existing link to the exchange are still working so I not really sure what setting should i look into. I was thinking
    about restoring back from Window Server Backup but was advise not to do it unless there are ways to look back the previous setting from the backup.
    One of my ex-boss told me could be the Exchange Certificate but wasn't sure.
    I really appreciate someone could advice and help me resolved this issue.
    IT Tech Supports

    Actually all are affected, but i manage to solved it running Virtual test version to trace the issue and finally able to fix it. Thanks for asking.
    IT Technician

  • Sales Order Created with reference to Contract - Exchange rate Issue

    When Sales Order created with reference to contract VBKD fields KURSK and KURSK_DAT gets copied from contract and not redetrmined based on pricing date and Exchange rate type. I expected it to be determined based on pricing date is standard. What I am missing, should it be controlled by data transfers
    If Document currency and condition currency are different it cause problems with incorrect condition values are calculated, as KOMP-KURSK are copied from VBKD-KURSK
    Any help or directions would be greatly appreciated . We are on 4.7 ISOIL
    Sincerely Julietta

    Well,
    and if we have the same issue, but we don't have OIL Version, but simple 4.6C, which solution has to be applied then?
    Thank you
    Standa

  • Transfer of Freight Conditions to Billing Document - exchange rate issue

    I am having an issue with my freight costs copy to customer billing document and the exchange
    rate causing the values to change. 
    Example - SCD freight = 400 USD, but vendor is being invoiced in BRL (807.44). 
    The freight is passed to customer billing document, which happens to have local document currency of
    EUR, but customer being invoiced in USD.  However the freight is going thru some kind of exchange rate conversion, causing my original 400 USD freight
    to show as 414.44 USD on the customer invoice.
    I am looking for way to keep the freight from changing between SCD + Customer Billing document.
    Regards
    Rita

    Can you share your screens from F-60 involving EUR to USD conversion?
    Also, try using transaction EWCT to test conversions between currencies,
    you can choose your two currencies that give you the issue, and test by
    entering the initial value, seeing the converted value.

  • Exchange rate issue during PO creation

    Dear Friends
    I am getting the below error whenever I am trying to create an Import PO
    Enter rate USD / INR rate type  for 28.10.2010 in the system settings
    Message no. SG105
    I have entered the rates in OB08 table-  for direct & Indiret exchange rates for M
    I also have cheched the OBBS and made entries for the date 28.10.2010
    But still I am getting the error
    How do I proceed
    Samuel
    Edited by: samuel mendis on Oct 28, 2010 1:07 PM

    Guys
    We have solved this issue. Even though we were getting the SG105 error, the real problem was some where else. 
    We have never used CIN in our our organisation as it is not applicable. The problem we did is to use the Import pricing procedure for our use which was copied from IN: Purchasing for Imported materials.
    Whenever we tried to create a Import PO it was validating the CVD entries which we make in the company code settings for Tax on Goods Movements. Once I maintained a dummy G/L account the error was gone.
    The problem is why it validated CVD during PO creation we never understood. Since in my opinion CVD capturing is done during Invoicing verification stage and not during PO stage. Either way we have already updated these details to the SAP Support bench.
    Thanks
    Samuel

Maybe you are looking for