FAS3220 and FAS2240 direct attach on fabric interconnect 6296UP

Hello everybody
I have the following architecture
1 Cisco Catalyst 6509-E
1 Cisco Catalyst 3560-x
2 Fabric Interconnect 6296UP
1 FAS 3220 (principal storage)
1 FAS2240 (vault backup)
1 chasis cisco UCS 5108
5 blade servers Cisco UCS B200M3
Firmware version: 2.2(3c)
Fabric Interconnect are direct attach on fabric interconnect 6296up and the ports are configurated as FC storage ports
My question is the following:
Can I zoning fabric interconnect with FAS3220 and FAS2240?
Can I present LUNS of FAS2240 and FAS3220 at the same time on the same boot policy, same san boot policy, and the same organization?
Thanks for your help

Well, even if that was possible. You're accounting for a critical failure - i.e. a failure of two redundant devices (both 3220s, which I would have assume would be running in a cluster ... or 7mode).
While just upstream you have a single cat 6500 - which would be a single point of failure.
Logic would dictate to account for a single device failure all across the path before looking into multi-device failure.

Similar Messages

3510 network interfaces and # of direct attached hosts

Hi,
I have 3510 array with Dual FC controllers and each controller has a network interface. I am trying to congiure both NICs with separate IPs but I only see one interface through console. How to set the 2nd interface up?
And there are 8 FC host ports but I only see 4 , I need to attach 6 to 8 hosts directly to the array and not able to see 8 channels. Need help to see all 8 channels and to maps Logical drives to all 8.
Thanks
ssgn

The array is configured to use the controllers for failover.

Fabric Interconnect and storage solutions

Dear
Please I would like to clarify a question, is that a solution of storage, such as EMC VNX5300 can be connected directly to a Fabric Interconnect, but would lose functionality when connected to a Nexus 5000 switch. I would like someone to clarify this doubt indicating that functionality is lost when direct connection would be advisable to FI or the Nexus.
Regards

In versions of UCS earlier than 2.1, you had the option to useDirect Attached Storage DAS with UCS. However, you needed a SAN switch connected to the FI so the switch could push the zone database to the FI. That is, the UCS platform was not able to build a zone database
With the release of Version 2.1, UCS now has the ability to build its own zone database. You can have DAS with UCS without the need for a SAN switch to push the zoning configuration
hope this helps

Fabric Interconnect To MDS 9148 FC Port Channel/Trunks

Is it possible to create both a Port Channel and Trunk on a Cisco MDS 9148? Yes correct?
Or can I only trunk between the 2 MDS switches and not the MDS to Fabric Interconnect?
These FC links would be connected to a 2248XP Fabric Interconnect carrying multiple VSANs from the MDS to the Fabric Interconnect.
Thanks

Hello,
Yes, you can have trunk links grouped into port channel ( F port-channel trunking ) between FI and MDS.
http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/gui/config/guide/2.0/b_UCSM_GUI_Configuration_Guide_2_0_chapter_0101.html
Padma

6120 Fabric Interconnect

Is it possible to connect both ethernet switch and FC switch from 6120 Fabric Interconnect using the 8 port extended module?

Dhinesh,
Which expansion module are you using? N10-E0440 or N10-E0080 (both of them have eight ports).
If its E0440 - Yes, you can use it for both Ethernet uplink as well as FC uplink.
E0080 - Is just FC ports.
(the ports on the module which have green color on them are FC ports).
Here is the URL to the Spec sheet for your refernce:
http://www.cisco.com/en/US/prod/collateral/ps10265/ps10276/spec_sheet_c17-665945.pdf
./Abhinav

Port-channel Problem between Fabric Interconnect and N7K vPC

Dear all,
I have a problem with Port-channel Uplink between Fabric Interconnect with N7K using vPC
This is my network topology for UCS Deployment
In N7K I has configured vPC for red link and green link, at Fabric Interconnect A I has configured Port-Channel with member is Port 1 and Port 2, uplink is red link. At Fabric Interconnect B, I has configured Port-Channel with member is Port 1 and Port 2, uplink is green link.
The show interface port-channel on N7K is good, every port-channel is up and have all member. But At Fabric Interconnnect, when I see on UCS Manager, the status of Port-Channel on Fabic A and Fabric B is fault with Additional Info: No operational member. Although all link is link up and I has status of Port-Channel is enable on UCS Manager. When I see the Properties of Port 1, Port 2 on Port-channel, I see the membership status is : individual. This mean port-channel is not up and no membership in this configuration. I want to using port-channel for load balance and plus more bandwidth for uplink to 20Gig. I don't understand why ?
Please help me resolve this problem, I has send the capture screen of UCS Manager when I show status of Port-channel and Port-member in port-channel in attach items.
Anyone can help me to resolve this, thanks you very much. Please reference attach items for more detail about fault.
Thanks,
Trung.

Thanks Matthew very much,
I has resolved this problem. The reason of problem is miss match protocol of port-channel between N7K and Fabric Interconnect. The Fabric Interconnect always use LACP protocol, but N7K using Port-channel mode on, that why the port-channel failed. I has configured LACP for port-channel in N7K, it has resolved the problems.
Thanks,
Trung.

Port-channel L2 problem with Fabric Interconnect and Nexus 7010

Hi,
i using port-channel from both fabric interconnect to N7k with 3 cables per Fabric Interconnect.
but, my problem is when i creating port-channel, Fabric Interconnect don't support mode ON dan rate-mode share in Interface 10G Nexus 7010.
I was trying :
1. I using non dedicated port in Nexus 7010.
      - rate-mode share
      - channel-group 1 mode active
      - switchport mode trunk
when i using this option, the port-channel in Nexus 7010 was suspended
2. I using non dedicated port in Nexus 7010
     - rate-mode share
     - channel group 1 mode on
     - switchport mode trunk
when i using this option, the port-channel in Nexus 7010 was came up, but in Fabric interconnect was failed.
3. I using dedicated port in Nexus 7010
     - rate-mode share
     - channel group 1 mode active
     - switchport mode trunk
when i using this option, the port-channel in Nexus 7010 was suspended
4. I using dedicated port in Nexus 7010
     - rate-mode dedicated
     - channel group 1 mode active
     - switchport mode trunk
when i using this option, the port-channel in Nexus 7010 was came up and running well.
but, the problem is my costumer do not want using a dedicated rate-mode. if i using dedicated mode the only available port is 8 interfaces instead of 32 ports. i want to using rate-mode share in nexus 7010.
is there any way to configuring port-channel using mode on in fabric interconnect ? i was trying using CLI to create port-channel in Fabric interconect but i cannot configure the channel group protocol.
i attach the topology of N7K with Fabric interconnect.
regards,
Berwin H

Hi Manish,
the issue was solved, i was fix it last week.
the solution is:
i enable the license grace-priode (since my license is Enterprise so cannot create VDC) then i create a VDC (ex: VDC 2) so i allocate the interface on all module
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin-top:0cm;
mso-para-margin-right:0cm;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0cm;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
N7K-M132XP-12 to VDC 2. after that i delete VDC 2 then all interface back to VDC 1 (default vdc). then i enable the rate-mode share in dedicated port and bundle into port-channel and its working.
i dont know why it must move to VDC first then it will working, maybe cisco can explain the reasons.
So here the result of my port-channel :
SVRN7KFARM-HO-01# show port-channel summary
Flags: D - Down        P - Up in port-channel (members)
        I - Individual H - Hot-standby (LACP only)
        s - Suspended   r - Module-removed
        S - Switched    R - Routed
        U - Up (port-channel)
Group Port-       Type     Protocol Member Ports
      Channel
1     Po1(SU)     Eth      LACP      Eth1/1(P)    Eth1/2(P)    Eth1/3(P)
                                     Eth1/4(P)    Eth1/25(P)
2     Po2(SU)     Eth      LACP      Eth1/9(P)    Eth1/10(P)   Eth1/11(P)
                                     Eth1/12(P)   Eth1/26(P)
3     Po3(SU)     Eth      LACP      Eth1/17(P)   Eth1/18(P)
4     Po4(SU)     Eth      NONE      Eth10/32(P) Eth10/34(P) Eth10/35(P)
                                     Eth10/36(P)
Thanks.
Berwin H

HT201210 you are running the latest version of iTunes, have no other USB devices attached, have no security software installed, and are directly connected to your ISP source, simply restarting the computer and the iOS device can clear up certain issues th

you are running the latest version of iTunes, have no other USB devices attached, have no security software installed, and are directly connected to your ISP source, simply restarting the computer and the iOS device can clear up certain issues that could prevent you from restoring. After restarting the computer and iOS device, attempt to restore again.

How big is your library? I would recommend the following troubleshooting steps:
- Backup your library. Always a good idea before messing with things.
- Create a new library.   Refer to this article for details: http://support.apple.com/kb/HT1589. This won't delete your old library, you're just creating a new empty one. Also refer to this article to get back to your old library later.
- Add a few albums into this new library. Not everything, just a small sampling, as a test.
- Activate Match on this new library. You shouldn't have to re-pay, it should just say "Add Computer" or similar.
- At this point, Match should run again. With just a few albums it should complete in just a few minutes.
If iTunes doesn't crash at this point, then likely there's something about your original library that Match doesn't like - what that is I don't know, but at least you'll know it's not your PC.   If iTunes still crashes, then if could be a number of other things, but probably not your library.   My next suggestion (if you haven't already done this) is to uninstall / reinstall iTunes.   If that doesn't work, then my next ideas you won't like.

No link between IOM port 2/2/3 and fabric interconnect B

Hello
I am trying to remove an uplink from an IOM to the fabric interconnect as its not required. I have tried to reset the I/O module and re-acknowledge the chassis with no luck, it is still shown in the GUI with the error message as in the subject. We are currently running 2.0(1s). The kit isn't in production yet.
Thanks for any help

Yes i agress thats a pretty heavy approach to clean it. No if you left it there as it is, there would have been no operational issues. It would have just left this fault in the UCSM.
./Abhinav

How to find both direct and indirect responsibilites attached to user

Hi All,
I have a requirement to write a sql to list all direct and indirect responsibilities attached to a particular user.
Please help me.
Thanks,
Raghav.

Hi;
Pelase see below which could be helpful for your issue:
responsibilty -to find any users assigned
to find any users assigned to a responsibilty
Regard
Helios

I've recently added the MacAir to my Microsoft /Windows network. The Mac sees my printers but all the printers are "paused" and I cannot print, even if directly attached. How do I fix this?

I've recently added the MacAir to my Microsoft /Windows network. The Mac sees my printers but all the printers are "paused" and I cannot print, even if directly attached. How do I fix this?

Yes, I've that and it didn't work. Today, I reinstalled printer software on one printer and the "paused" message changed to "offline". It's a three-in-one printer. I turned off and on again and it still says "offline"
"

- No link between IOM port 3/2/2 and fabric interconnect B:1/18

Specifically I'm trying to find out what the 3/2/2 means in - No link between IOM port 3/2/2 and fabric interconnect B:1/18

This from the fault reference guide:
"No link between IOM port [chassisId]/[slotId]/[portId] and fabric interconnect [switchId]:[peerSlotId]/[peerPortId]"
http://www.cisco.com/en/US/docs/unified_computing/ucs/ts/faults/reference/UCS_SEMs.html#wp1306388

10G-Ethernet RJ45 (10GBASE-T) and direct attached SFP+ Twinax (10GBASE-CR)?

Hello,
I'm searching a switch that does support 10G-Ethernet RJ45 (10GBASE-T) and direct attached SFP+ Twinax (10GBASE-CR).
I do not have big requirements, but it should be as cheap as possible.

Would like to connect an SFP+ port to 10GBASE-T port?
Maybe a media converter is enough for your demand.

Monitoring traffic between UCS fabric extenders and fabric interconnect?

What is the best way to monitor the traffic between UCS fabric extenders (chassis) and fabric interconnect? Specifically I am looking for parameters to keep an eye on to determine when we may need to move from 2 links per fabric extender to 4 to handle greater IO needs.
Thanks.
- Klaus

One way you could monitor usage is by looking at the interface stats just as you would for any switch uplink.
Connect to the Cluster CLI
connect NXOS
Look at the input/output rate of your Server Uplink interfaces.
In my example I'm using fixed ports 1 through 4 on my FI's connecting to the IOM of the Chassis.
UCS-A(nxos)# show int eth1/1-4 | include rate
30 seconds input rate 17114328 bits/sec, 1089 packets/sec
30 seconds output rate 8777736 bits/sec, 693 packets/sec
    input rate 5.07 Mbps, 198 pps; output rate 1.03 Mbps, 99 pps
30 seconds input rate 2376 bits/sec, 0 packets/sec
30 seconds output rate 1584 bits/sec, 2 packets/sec
    input rate 1.58 Kbps, 0 pps; output rate 1.58 Kbps, 3 pps
30 seconds input rate 2376 bits/sec, 0 packets/sec
30 seconds output rate 31680 bits/sec, 20 packets/sec
    input rate 1.58 Kbps, 0 pps; output rate 30.89 Kbps, 18 pps
30 seconds input rate 2376 bits/sec, 0 packets/sec
30 seconds output rate 1584 bits/sec, 1 packets/sec
    input rate 1.58 Kbps, 0 pps; output rate 1.58 Kbps, 3 pps
If you notice your two links pushing near 10G consistently, it might be time to add another 2 link.
Other than this you can use SNMP to log the stats and look based on daily/weekly/monthly usage.
Robert

Fabric interconnect and Native Vlan

Hi
I just want to ask a simple question
is there any precautions with native vlan between the Switched infrastructure and the Fabric interconnect ?!
I mean can I use any vlan as a native vlan ex.999 "anything but not 1" ?!

As a security best practice on trunks carrying multiple VLANs you should not allow the native vlan on the line. When you have a single VLAN going to a device, an end node for example, the port should be configured as an access port with a single data VLAN, and potentially a voice vlan if that will be used.
For example, our N5Ks have a trunk to each of our UCS interconnects. We set the native VLAN on the n5k side to 999. 999 is not in the allowed list for the trunk then, so the native VLAN never makes it to the ucs. On the ucs then, any server that can handle VLANs (esxi for example) we send only tagged VLANs -- no VLAN is marked native, thus accomplishing the same thing as we did for the n5k to FI link.
It is recommended to not leave your native VLAN as 1 as best practice. It's less of a concern if the native VLAN isn't in the allowed list, but to avoid mis configuration issues you should set it to another VLAN.

FAS3220 and FAS2240 direct attach on fabric interconnect 6296UP

Similar Messages

Maybe you are looking for