Firewall service not permitting as it should

The firewall services in OS X Server 10.5.1 are not permitting traffic as expected.
Any ideas here to help me understand why would be appreciated.
IP address block 11.22.33.0/26 has been changed from the original but should have no effect on the example. I don't understand why address 11.22.33.62 hhas no access.
- Steve
root# *serveradmin status ipfilter*
ipfilter:state = "RUNNING"
root# *ipfw list*
00001 allow udp from any 626 to any dst-port 626
01000 allow ip from any to any via lo0
01010 deny log logamount 1000 ip from any to 127.0.0.0/8
01020 deny log logamount 1000 ip from 224.0.0.0/4 to any in
01030 deny log logamount 1000 tcp from any to 224.0.0.0/4 in
12300 allow tcp from any to any established
12301 allow tcp from any to any out
12302 allow tcp from any to any dst-port 22
12302 allow udp from any to any dst-port 22
12303 allow udp from any to any out keep-state
12304 allow tcp from any to any dst-port 53 out keep-state
12304 allow udp from any to any dst-port 53 out keep-state
12305 allow udp from any to any in frag
12306 allow tcp from any to any dst-port 311
12307 allow tcp from any to any dst-port 625
12308 allow udp from any to any dst-port 626
12309 allow icmp from any to any icmptypes 8
12310 allow icmp from any to any icmptypes 0
12311 allow igmp from any to any
12312 allow tcp from any to any dst-port 110
12312 allow udp from any to any dst-port 110
12313 allow tcp from any to any dst-port 25
12313 allow udp from any to any dst-port 25
12314 allow tcp from any to any dst-port 16080
12315 allow ip from 192.168.0.0/24 to any via en0 keep-state
12316 allow udp from any 68 to any dst-port 67 via en0
12317 allow tcp from 11.22.33.0/26 to any dst-port 687
12318 allow tcp from 11.22.33.0/26 to any dst-port 5988,5989
12319 allow tcp from 11.22.33.0/26 to any dst-port 5432
12320 allow tcp from 11.22.33.0/26 to any dst-port 443
12321 allow tcp from 11.22.33.0/26 to any dst-port 3283,5900
12321 allow udp from 11.22.33.0/26 to any dst-port 3283,5900
12322 allow tcp from 11.22.33.0/26 to any dst-port 311
12323 allow tcp from 11.22.33.0/26 to any dst-port 80
12324 allow tcp from 11.22.33.0/26 to any dst-port 8080
12325 allow tcp from 11.22.33.0/26 to any dst-port 749
12325 allow udp from 11.22.33.0/26 to any dst-port 749
12326 allow tcp from 11.22.33.0/26 to any dst-port 88
12326 allow udp from 11.22.33.0/26 to any dst-port 88
12327 allow tcp from 11.22.33.0/26 to any dst-port 600-1023
12327 allow udp from 11.22.33.0/26 to any dst-port 600-1023
65534 deny log logamount 1000 ip from any to any
65535 allow ip from any to any
in /var/log/ipfw.log
Jan 8 11:10:56 ssg4 ipfw[31959]: 65534 Deny TCP 11.22.33.62:63681 192.168.0.5:8008 in via en0

1. Hacked hosts file?
       etc/hosts
        https://discussions.apple.com/docs/DOC-8091
2. Get rid of uTorrent.
3. Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".

Similar Messages

HT4528 I have an IPhone5. The screen goes blue, then B & W snow, then makes a short hissing sound and shuts off. It did it 3-4 times and now it will not turn on. Should I try to have it serviced or replace it?

I have an IPhone 5. The screen flashes bright blue, then B & W snow, then makes a short hissing sound and shuts off. It did it 3-4 times and now it will not turn on. Should I try to have it serviced or replace it?

Get it looked at by visiting an Apple Store or Authorized Apple Service Provider. If you can't, contact Apple Support to get it serviced.
iPhone - Contact Support - Apple Support

HT3302 my new iphone5 screen got cracked.i bought it from australia and i live in India.Now i'm not getting any service in india.what i should do now??plz help

my new iphone5 screen got cracked.i bought it from australia and i live in India.Now i'm not getting any service in india.what i should do now??plz help

You will have to return to Australia to get it serviced.

Error: Worklist Service Action Not Permitted Error

Hi,
I am getting following exception if trying to change the action status as Approve for a particular user, after fetching the context and taskId for the same user.
<2006-08-25 12:45:48,122> <ERROR> <default.collaxa.cube.services> <PCException::
<init>> Worklist Service Action Not Permitted Error.
<2006-08-25 12:45:48,142> <ERROR> <default.collaxa.cube.services> <PCException::
<init>> User "sfitzger" is not permitted to perform the action "APPROVE" on task
"Quote 4" with id "a56cbc814a4c93a2:1a001ff:10d42242012:-7fcb".
<2006-08-25 12:45:48,152> <ERROR> <default.collaxa.cube.services> <PCException::
<init>> Fix the system configuration if the user does not have privilege to perf
orm the action on the task.
06/08/25 12:45:48 ORABPEL-10145
---Janit

I have found the problem.
No Approve anymore, Use Accept.
thx,
Janit

Ads keep appearing on screen whenever I use any browser, either Safari or Chrome. I used AdwareRemover and it did not work. What should I do? The ads are powered by "PSJ 4.2"

What should I do?

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of it have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Bluetooth SerialATA Extensions Applications Frameworks PrefPane Fonts 1024 85 percent 20480 1 MB/s 25000 ports KiB/s DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB 'com.adobe.AAM.Updater-1.0 com.adobe.AAM.Updater-1.0 com.adobe.AdobeCreativeCloud com.adobe.CS4ServiceManager com.adobe.CS5ServiceManager com.adobe.fpsaud com.adobe.SwitchBoard com.adobe.SwitchBoard com.apple.aelwriter com.apple.AirPortBaseStationAgent com.apple.FolderActions.enabled com.apple.installer.osmessagetracing com.apple.mrt.uiagent com.apple.ReportCrash.Self com.apple.rpmuxd com.apple.SafariNotificationAgent com.apple.usbmuxd com.citrixonline.GoToMeeting.G2MUpdate com.google.keystone.agent com.google.keystone.daemon com.microsoft.office.licensing.helper com.oracle.java.Helper-Tool com.oracle.java.JavaUpdateHelper com.oracle.java.JavaUpdateHelper org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.startx' '879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 3694147963 1233118628 2456546649 2806998573 2778718105 2636415542 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 523110921 2883943871 3873345487' 51 5120 files 4 1000 25 5120 );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' '%s (UID %s) is using %s %s' '\nContents of %s\n -\tmod date: %s\n -\tchecksum: %s\n%s\n' '\n ...and %s more line(s)\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("'"${f[5]}"'",$0,u,q,"'${p[$2]}'");} ';};s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[46]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[47]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<10) print "com.apple.";} ' ' { sub(/ :/,"");print|"tail -n'${p[48]}'";} ' ' NR==2&&$4<='${p[49]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:.+//p ' '/^root$/p' ' !/^\/[AD]|\/Contents\/.+\/Contents\/|\.prefP/&&/\/(Lib|usr).+\/(.+\.lproj|Contents|Info\.plist|Resources)|\.framework$/ { n++;sub(/\/Info\.plist$/,"");sub(/\/([A-Za-z_]+\.lproj|Contents|Resources|Versions)(\/.+)?/,"");print|"sort|uniq";} END { if(n<1100) print "/System/";} ' '/\.dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { split("'"${p[41]}"'",b);split("'"${p[42]}"'",c);for(i in b) print b[i]".plist\t"c[i];if(n<500) print "Launch";} ' ' /^\/(Ap|Dev|Inc|Prev)|\.(action|bundle|framework|kext|pkg|prefPane|service|vst)$/d;p;' 's/Pr.+n //p' ' /.kext$/ { s=system("PlistBuddy -c Print\\ :OSBundleRequired "$0"/*/I*|grep -q Sa");if(s==0) $0=$0" S"; };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&& $3!~/(255\.){3}0/)||(/v6:/&&$2!~/A/) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\$[0-9]+\$\$.+\$/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 23`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"cksum "F|getline C;split(C, A);C=A[1];"stat -f%Sm "F|getline D;"file -b "F|getline T;if(T~/^Apple b/) { f="";l=0;while("PlistBuddy -c Print "F|getline g) { l++;if(l<=L) f=f"\n "g;};};if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F"\n -\t"T;printf("'"${f[6]}"'",F,D,C,f);if(l>L) printf("'"${f[7]}"'",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */ /;' ' s/^.+ |\(.+$$//g;p ' '/\.(appex|pluginkit)\/Contents\/Info\.plist$/p' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' ' $3~/^[1-9][0-9]{0,2}(\.[1-9][0-9]{0,2}){2}$/ { i++;n=n"\n"$1"\t"$3;} END { if(i>1) print n;} ' ' s/:[^:]+$//;s/ +([0-9]+)(.+)/\2: \1/p;' ' { gsub(/[()"]/,"",$3);if(!$3) $3="N/A";print $3;} ' ' /es: ./{ s/^.+://;b0'$'\n'' };/^ +C.+ted: +[NY]/H;/:$/b0'$'\n'' d;:0'$'\n'' x;/: +N/d;s/\n.+//p;' ' /[my]: /H;/^ *Lo.+: /{ H;b0'$'\n'' };$b0'$'\n'' d;:0'$'\n'' x;/: [3IU]/!d;s/.+n: //p;' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab iotop top pkgutil 'PlistBuddy 2>&1 -c Print\' whoami cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom 'mdfind -onlyin /' ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' pluginkit scutil dtrace profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil lsof test osascript\ -e netstat mdls );S1() { printf kMDItemContentTypeTree=com.apple.$1;};S2() { printf 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :'$1' {} \;|uniq';};c2=(com.apple.loginwindow\ LoginHook ' /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" "`S2 CFBundleDisplayName`" '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '-F \$Message -k Sender kernel -k Message CSeq "I/O e"|sort|uniq -c' :${p[35]} :Label '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$(RefProc): \$Message' -k Sender Req 'fsev|kern|launchd' -k RefProc Rne 'Aq|WebK' -k Message Rne '08012|Goog|ksadm|probe|Roame|SMC:|smcD|sserti|suhel| VALI|ver-r|xpma' -k Message Req 'abn|bad |Beac|caug|corru|dead[^bl]|FAIL|fail|GPU |hfs: Ru|idle ex|inval|jnl:|last value [1-9]|NVDA$|pagin|pci pa|proc: t|Roamed|rror|SL|TCON|Throttli|tim(ed? ?|ing )o|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '/S*/*/Ca*/*xpc* >&- ||echo No' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' "`S1 bundle`" "`S1 mach-o-dylib`" "`S2 ${p[35]}`" "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????|wc -l' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' " -F '\$Time \$Message' -k Sender kernel -k Message CSeq 'n Cause: -' " -i '-app Safari UserStyleSheetEnabled' -name\ kMDItem${p[35]} );N1=${#c2[@]};for j in {0..14};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files I/O\ errors 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents XPC\ cache Startup\ items Admin\ access Root\ access Bundles dylibs Stylesheet Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching Nets Descriptors App\ extensions Lockfiles Memory\ pressure SMC Shutdowns );N3=${#l[@]};for i in {0..8};do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};A'$((7+i))'() { v=` eval sudo "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};';done;A9(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"|sort`;};C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "${s[63]}"<<<"$v"`&&C1 1 $1;};for i in 1 2 7 8;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 $((N3+4));for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 0 $((N1+8)) 71 $((N3+3));D13 1 10 7 9;D13 1 11 8 10;B1&&D73 19 53 67 55;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D13 5 5 69 1;D13 5 54 30 56;D23 5 14 12 14;D22 6 36 13 15;D22 20 52 66 54;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D82 35 49 61 51;D82 11 17 17 20;for i in 0 1;do D82 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A8 18 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;D13 4 21 24 26;B4 4 12 26;for i in {0..3};do A1 0 $((N1+10+i)) 72;B7 12;B4 0 14 31;A4 39 57 70 0;B2 15;B6 14 15 4;C3 $((N3+5+i));done;A1 24 22 29;B7 12;B2 14;A4 39 57 70 0;B2 15;B6 14 15 4;C3 29;B3 4 13 27;A1 24 23 32;B7 13;C3 30;B3 4 0 65;A3 14 6 32 0;B4 0 16 11;A1 26 50 64;B7 16;C3 52;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D73 21 0 32 19;D73 10 42 32 40;D82 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D12 22 20 32 25;D22 0 $((N1+14)) 51 32;D13 4 8 41 6;D12 21 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 38 55 68 50;D23 33 34 42 37;B1&&D83 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 10 42 32 41;D13 37 2 48 43;A1 4 3 60;B2 30;A1 4 24 60;B2 31;B6 30 31 4;C3 5;D12 21 56 35 31;D12 21 48 49 49;B3 4 22 57;A1 21 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D12 4 51 32 53;D23 22 9 37 7;A9;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

[webgl] sluggish performance ( /dev/nvidia0 Operation not permitted )

We (folks on #archlinux already tried helping) have been at this for hours now... no solution found yet.
summary: webgl works but performance is sluggish(20 to 30fps) which makes me assume it's falling back to software rendering for some unknown reason
already tried many things: vmalloc kernel parameters, irq control left to bios/archlinux, being in the video group, not being in the video group, having an xorg.conf, not having an xorg.conf, different AGP aperture sizes in BIOS, regular gl performance is normal (60 fps (capped to display refresh) in glxgears), only webgl slugs, card (GT 7600 256MB VRAM) should support the required shader language version for webgl (and webgl performance is only sluggish in linux... so I think it must be a configuration issue on some driver/kernel/browser setting?)
Different browsers show different messages when started from the console but I don't know what to make of those and googling them did not reveal any solutions so far either.
browsers tested: firefox, google-chrome(from AUR), chromium
window managers tested: enlightenment, fluxbox
kernel: linux-lts
driver: nvidia-304xx-lts (can not use Nouveau as Nouveau keeps locking up the GPU)
It's a fresh archlinux installation (Ubuntu had the same performance problem btw in case that might be useful to know for looking for the cause).
Everything I tried so far, did not change anything about the sluggish webgl performance problem.
One thing I noticed is that /dev/nvidia0 and /dev/nvidiactl both do not exist until after "startx". Could that be a problem?
Here are some logs, hoping someone sees something which looks suspicious and knows what else I could try to make it work.
dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.14.23-1-lts (nobody@home-andyrtr-arch64-chroots-testing-x86_64-andyrtr) (gcc version 4.9.1 20140903 (prerelease) (GCC) ) #1 SMP Thu Oct 30 19:41:12 CET 2014
[ 0.000000] Command line: BOOT_IMAGE=../vmlinuz-linux-lts ipv6.disable=1 vmalloc=256M root=/dev/sda1 rw initrd=../initramfs-linux-lts.img
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000005ffbffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000005ffc0000-0x000000005ffcffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000005ffd0000-0x000000005fffffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff7c0000-0x00000000ffffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.3 present.
[ 0.000000] DMI: ASUSTek Computer Inc. K8N-E-Deluxe/'K8N-E-Deluxe', BIOS 1012.007 01/18/2006
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP bridge at 00:00:00
[ 0.000000] Aperture from AGP @ e0000000 old size 32 MB
[ 0.000000] Aperture size 4096 MB (APSIZE 0) is not right, using settings from NB
[ 0.000000] Aperture from AGP @ e0000000 size 32 MB (APSIZE 0)
[ 0.000000] e820: last_pfn = 0x5ffc0 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FFC0000000 write-back
[ 0.000000] 1 base 0040000000 mask FFE0000000 write-back
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [ffff8800000ff780]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01b40000, 0x01b40fff] PGTABLE
[ 0.000000] BRK [0x01b41000, 0x01b41fff] PGTABLE
[ 0.000000] BRK [0x01b42000, 0x01b42fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x5fa00000-0x5fbfffff]
[ 0.000000] [mem 0x5fa00000-0x5fbfffff] page 2M
[ 0.000000] BRK [0x01b43000, 0x01b43fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x5c000000-0x5f9fffff]
[ 0.000000] [mem 0x5c000000-0x5f9fffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x5bffffff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x5bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x5fc00000-0x5ffbffff]
[ 0.000000] [mem 0x5fc00000-0x5fdfffff] page 2M
[ 0.000000] [mem 0x5fe00000-0x5ffbffff] page 4k
[ 0.000000] BRK [0x01b44000, 0x01b44fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x5fc97000-0x5ffbffff]
[ 0.000000] ACPI: RSDP 00000000000f9cb0 000014 (v00 ACPIAM)
[ 0.000000] ACPI: RSDT 000000005ffc0000 000030 (v01 A M I OEMRSDT 01000618 MSFT 00000097)
[ 0.000000] ACPI: FACP 000000005ffc0200 000081 (v02 A M I OEMFACP 01000618 MSFT 00000097)
[ 0.000000] ACPI: DSDT 000000005ffc0400 004524 (v01 A0055 A0055003 00000003 INTL 02002026)
[ 0.000000] ACPI: FACS 000000005ffd0000 000040
[ 0.000000] ACPI: APIC 000000005ffc0390 000068 (v01 A M I OEMAPIC 01000618 MSFT 00000097)
[ 0.000000] ACPI: OEMB 000000005ffd0040 000041 (v01 A M I OEMBIOS 01000618 MSFT 00000097)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] Scanning NUMA topology in Northbridge 24
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000005ffbffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x5ffbffff]
[ 0.000000] NODE_DATA [mem 0x5fc92000-0x5fc96fff]
[ 0.000000] [ffffea0000000000-ffffea00017fffff] PMD -> [ffff88005dc00000-ffff88005f3fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0x5ffbffff]
[ 0.000000] On node 0 totalpages: 393054
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 6079 pages used for memmap
[ 0.000000] DMA32 zone: 389056 pages, LIFO batch:31
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: BIOS IRQ0 override ignored.
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] smpboot: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000e3fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e4000-0x000fffff]
[ 0.000000] e820: [mem 0x60000000-0xfebfffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88005fa00000 s86656 r8192 d23936 u2097152
[ 0.000000] pcpu-alloc: s86656 r8192 d23936 u2097152 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 386890
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=../vmlinuz-linux-lts ipv6.disable=1 vmalloc=256M root=/dev/sda1 rw initrd=../initramfs-linux-lts.img
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] AGP bridge at 00:00:00
[ 0.000000] Aperture from AGP @ e0000000 old size 32 MB
[ 0.000000] Aperture size 4096 MB (APSIZE 0) is not right, using settings from NB
[ 0.000000] Aperture from AGP @ e0000000 size 32 MB (APSIZE 0)
[ 0.000000] Node 0: aperture @ e0000000 size 256 MB
[ 0.000000] Memory: 1532388K/1572216K available (5187K kernel code, 858K rwdata, 1640K rodata, 1136K init, 1300K bss, 39828K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS:8448 nr_irqs:256 16
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 6291456 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2210.711 MHz processor
[ 0.010032] Calibrating delay loop (skipped), value calculated using timer frequency.. 4421.42 BogoMIPS (lpj=22107110)
[ 0.010037] pid_max: default: 32768 minimum: 301
[ 0.010061] ACPI: Core revision 20131218
[ 0.020405] ACPI: All ACPI Tables successfully acquired
[ 0.020642] Security Framework initialized
[ 0.020671] Yama: becoming mindful.
[ 0.020955] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.025410] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.027465] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.027473] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.028144] Initializing cgroup subsys memory
[ 0.028166] Initializing cgroup subsys devices
[ 0.028170] Initializing cgroup subsys freezer
[ 0.028173] Initializing cgroup subsys net_cls
[ 0.028177] Initializing cgroup subsys blkio
[ 0.028234] tseg: 0000000000
[ 0.028253] mce: CPU supports 5 MCE banks
[ 0.028279] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4, 1GB 0
tlb_flushall_shift: 6
[ 0.034575] Freeing SMP alternatives memory: 20K (ffffffff819f4000 - ffffffff819f9000)
[ 0.035713] ftrace: allocating 20111 entries in 79 pages
[ 0.049994] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 0.150150] smpboot: CPU0: AMD Athlon(tm) 64 Processor 3200+ (fam: 0f, model: 0c, stepping: 00)
[ 0.160000] Performance Events: AMD PMU driver.
[ 0.160000] ... version: 0
[ 0.160000] ... bit width: 48
[ 0.160000] ... generic registers: 4
[ 0.160000] ... value mask: 0000ffffffffffff
[ 0.160000] ... max period: 00007fffffffffff
[ 0.160000] ... fixed-purpose events: 0
[ 0.160000] ... event mask: 000000000000000f
[ 0.160000] x86: Booted up 1 node, 1 CPUs
[ 0.160000] smpboot: Total of 1 processors activated (4421.42 BogoMIPS)
[ 0.160000] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.160000] devtmpfs: initialized
[ 0.160000] PM: Registering ACPI NVS region [mem 0x5ffd0000-0x5fffffff] (196608 bytes)
[ 0.160000] pinctrl core: initialized pinctrl subsystem
[ 0.160056] RTC time: 14:37:08, date: 11/06/14
[ 0.160148] NET: Registered protocol family 16
[ 0.160332] cpuidle: using governor ladder
[ 0.160334] cpuidle: using governor menu
[ 0.160347] node 0 link 0: io port [1000, ffffff]
[ 0.160351] TOM: 0000000060000000 aka 1536M
[ 0.160356] node 0 link 0: mmio [a0000, bffff]
[ 0.160359] node 0 link 0: mmio [60000000, fe0bffff]
[ 0.160363] bus: [bus 00-ff] on node 0 link 0
[ 0.160365] bus: 00 [io 0x0000-0xffff]
[ 0.160367] bus: 00 [mem 0x000a0000-0x000bffff]
[ 0.160369] bus: 00 [mem 0x60000000-0xfcffffffff]
[ 0.160397] ACPI: bus type PCI registered
[ 0.160401] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.160498] PCI: Using configuration type 1 for base access
[ 0.161627] bio: create slab <bio-0> at 0
[ 0.161792] ACPI: Added _OSI(Module Device)
[ 0.161794] ACPI: Added _OSI(Processor Device)
[ 0.161795] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.161797] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.163305] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.164921] ACPI: Interpreter enabled
[ 0.164937] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131218/hwxface-580)
[ 0.164955] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.164958] ACPI: Using IOAPIC for interrupt routing
[ 0.164998] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.165137] ACPI: No dock devices found.
[ 0.170533] ACPI: Power Resource [ISAV] (on)
[ 0.173609] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.173619] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI]
[ 0.173626] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.173736] acpi PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.173739] acpi PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.173742] acpi PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.173745] acpi PNP0A03:00: host bridge window [mem 0x60000000-0xff7bffff] (ignored)
[ 0.173749] PCI: root bus 00: hardware-probed resources
[ 0.173755] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[ 0.173915] PCI host bridge to bus 0000:00
[ 0.173919] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.173922] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.173925] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.173928] pci_bus 0000:00: root bus resource [mem 0x60000000-0xfcffffffff]
[ 0.173943] pci 0000:00:00.0: [10de:00e1] type 00 class 0x060000
[ 0.173955] pci 0000:00:00.0: reg 0x10: [mem 0xe0000000-0xefffffff pref]
[ 0.174087] pci 0000:00:01.0: [10de:00e0] type 00 class 0x060100
[ 0.174184] pci 0000:00:01.1: [10de:00e4] type 00 class 0x0c0500
[ 0.174192] pci 0000:00:01.1: reg 0x10: [io 0x5080-0x509f]
[ 0.174203] pci 0000:00:01.1: reg 0x20: [io 0x5000-0x503f]
[ 0.174207] pci 0000:00:01.1: reg 0x24: [io 0x5040-0x507f]
[ 0.174221] pci 0000:00:01.1: PME# supported from D3hot D3cold
[ 0.174311] pci 0000:00:02.0: [10de:00e7] type 00 class 0x0c0310
[ 0.174319] pci 0000:00:02.0: reg 0x10: [mem 0xfebfd000-0xfebfdfff]
[ 0.174342] pci 0000:00:02.0: supports D1 D2
[ 0.174345] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.174378] pci 0000:00:02.0: System wakeup disabled by ACPI
[ 0.174441] pci 0000:00:02.1: [10de:00e7] type 00 class 0x0c0310
[ 0.174448] pci 0000:00:02.1: reg 0x10: [mem 0xfebfe000-0xfebfefff]
[ 0.174472] pci 0000:00:02.1: supports D1 D2
[ 0.174474] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.174506] pci 0000:00:02.1: System wakeup disabled by ACPI
[ 0.174565] pci 0000:00:02.2: [10de:00e8] type 00 class 0x0c0320
[ 0.174573] pci 0000:00:02.2: reg 0x10: [mem 0xfebffc00-0xfebffcff]
[ 0.174602] pci 0000:00:02.2: supports D1 D2
[ 0.174605] pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.174652] pci 0000:00:02.2: System wakeup disabled by ACPI
[ 0.174721] pci 0000:00:05.0: [10de:00df] type 00 class 0x068000
[ 0.174728] pci 0000:00:05.0: reg 0x10: [mem 0xfebfc000-0xfebfcfff]
[ 0.174733] pci 0000:00:05.0: reg 0x14: [io 0xec00-0xec07]
[ 0.174755] pci 0000:00:05.0: supports D1 D2
[ 0.174758] pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.174790] pci 0000:00:05.0: System wakeup disabled by ACPI
[ 0.174854] pci 0000:00:06.0: [10de:00ea] type 00 class 0x040100
[ 0.174861] pci 0000:00:06.0: reg 0x10: [io 0xe800-0xe8ff]
[ 0.174866] pci 0000:00:06.0: reg 0x14: [io 0xe400-0xe47f]
[ 0.174870] pci 0000:00:06.0: reg 0x18: [mem 0xfebfb000-0xfebfbfff]
[ 0.174890] pci 0000:00:06.0: supports D1 D2
[ 0.174967] pci 0000:00:08.0: [10de:00e5] type 00 class 0x01018a
[ 0.174983] pci 0000:00:08.0: reg 0x20: [io 0xffa0-0xffaf]
[ 0.175075] pci 0000:00:0a.0: [10de:00e3] type 00 class 0x010185
[ 0.175082] pci 0000:00:0a.0: reg 0x10: [io 0x09f0-0x09f7]
[ 0.175087] pci 0000:00:0a.0: reg 0x14: [io 0x0bf0-0x0bf3]
[ 0.175092] pci 0000:00:0a.0: reg 0x18: [io 0x0970-0x0977]
[ 0.175096] pci 0000:00:0a.0: reg 0x1c: [io 0x0b70-0x0b73]
[ 0.175101] pci 0000:00:0a.0: reg 0x20: [io 0xc800-0xc80f]
[ 0.175105] pci 0000:00:0a.0: reg 0x24: [io 0xc400-0xc47f]
[ 0.175191] pci 0000:00:0b.0: [10de:00e2] type 01 class 0x060400
[ 0.175286] pci 0000:00:0e.0: [10de:00ed] type 01 class 0x060400
[ 0.175325] pci 0000:00:0e.0: System wakeup disabled by ACPI
[ 0.175388] pci 0000:00:18.0: [1022:1100] type 00 class 0x060000
[ 0.175468] pci 0000:00:18.1: [1022:1101] type 00 class 0x060000
[ 0.175549] pci 0000:00:18.2: [1022:1102] type 00 class 0x060000
[ 0.175627] pci 0000:00:18.3: [1022:1103] type 00 class 0x060000
[ 0.175752] pci 0000:01:00.0: [10de:02e0] type 00 class 0x030000
[ 0.175770] pci 0000:01:00.0: reg 0x10: [mem 0xfd000000-0xfdffffff]
[ 0.175780] pci 0000:01:00.0: reg 0x14: [mem 0xc0000000-0xcfffffff pref]
[ 0.175790] pci 0000:01:00.0: reg 0x18: [mem 0xfc000000-0xfcffffff]
[ 0.175821] pci 0000:01:00.0: reg 0x30: [mem 0xfe9e0000-0xfe9fffff pref]
[ 0.175934] pci 0000:00:0b.0: PCI bridge to [bus 01]
[ 0.175940] pci 0000:00:0b.0: bridge window [mem 0xfa900000-0xfe9fffff]
[ 0.175943] pci 0000:00:0b.0: bridge window [mem 0xba800000-0xda7fffff pref]
[ 0.175986] pci 0000:02:0b.0: [1106:3044] type 00 class 0x0c0010
[ 0.175998] pci 0000:02:0b.0: reg 0x10: [mem 0xfeaff800-0xfeafffff]
[ 0.176005] pci 0000:02:0b.0: reg 0x14: [io 0xbc00-0xbc7f]
[ 0.176047] pci 0000:02:0b.0: supports D2
[ 0.176049] pci 0000:02:0b.0: PME# supported from D2 D3hot D3cold
[ 0.176124] pci 0000:00:0e.0: PCI bridge to [bus 02]
[ 0.176127] pci 0000:00:0e.0: bridge window [io 0xb000-0xbfff]
[ 0.176130] pci 0000:00:0e.0: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.176957] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
[ 0.177043] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *11
[ 0.177127] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[ 0.177211] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[ 0.177294] ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *11
[ 0.177374] ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *11
[ 0.177454] ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *9
[ 0.177533] ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *10
[ 0.177612] ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *11
[ 0.177706] ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *9
[ 0.177786] ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
[ 0.177867] ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *0, disabled.
[ 0.177947] ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0
[ 0.178035] ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 22) *0, disabled.
[ 0.178144] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *14
[ 0.178495] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.178498] vgaarb: loaded
[ 0.178499] vgaarb: bridge control possible 0000:01:00.0
[ 0.178573] PCI: Using ACPI for IRQ routing
[ 0.178578] PCI: pci_cache_line_size set to 64 bytes
[ 0.178617] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 0.178621] e820: reserve RAM buffer [mem 0x5ffc0000-0x5fffffff]
[ 0.178834] NetLabel: Initializing
[ 0.178836] NetLabel: domain hash size = 128
[ 0.178838] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.178866] NetLabel: unlabeled traffic allowed by default
[ 0.178945] Switched to clocksource refined-jiffies
[ 0.193118] pnp: PnP ACPI init
[ 0.193168] ACPI: bus type PNP registered
[ 0.193275] pnp 00:00: [dma 4]
[ 0.193336] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.193401] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.193439] pnp 00:02: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.193480] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.193867] pnp 00:04: [dma 2]
[ 0.193932] pnp 00:04: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.194190] pnp 00:05: [dma 3]
[ 0.194334] pnp 00:05: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.194597] pnp 00:06: Plug and Play ACPI device, IDs PNPb006 (active)
[ 0.194863] system 00:07: [io 0x0190-0x0193] has been reserved
[ 0.194867] system 00:07: [io 0x04d0-0x04d1] has been reserved
[ 0.194870] system 00:07: [io 0x4000-0x40ff window] has been reserved
[ 0.194873] system 00:07: [io 0x4400-0x44ff window] has been reserved
[ 0.194876] system 00:07: [io 0x4800-0x48ff window] has been reserved
[ 0.194881] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.194987] system 00:08: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.194990] system 00:08: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.194993] system 00:08: [mem 0xff780000-0xff7bffff] has been reserved
[ 0.194996] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.195070] pnp 00:09: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.195231] system 00:0a: [io 0x0480-0x0487] has been reserved
[ 0.195234] system 00:0a: [io 0x0d00-0x0d07] has been reserved
[ 0.195237] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.195468] pnp 00:0b: Plug and Play ACPI device, IDs PNPb02f (active)
[ 0.195722] pnp 00:0c: [dma 0 disabled]
[ 0.195790] pnp 00:0c: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.196055] pnp 00:0d: [dma 0 disabled]
[ 0.196135] pnp 00:0d: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.196351] system 00:0e: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.196355] system 00:0e: [mem 0x000c0000-0x000dffff] could not be reserved
[ 0.196358] system 00:0e: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.196360] system 00:0e: [mem 0x00100000-0x5fffffff] could not be reserved
[ 0.196363] system 00:0e: [mem 0xff7c0000-0xffffffff] has been reserved
[ 0.196366] system 00:0e: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.196611] pnp: PnP ACPI: found 15 devices
[ 0.196613] ACPI: bus type PNP unregistered
[ 0.203623] Switched to clocksource acpi_pm
[ 0.203683] pci 0000:00:0b.0: PCI bridge to [bus 01]
[ 0.203692] pci 0000:00:0b.0: bridge window [mem 0xfa900000-0xfe9fffff]
[ 0.203696] pci 0000:00:0b.0: bridge window [mem 0xba800000-0xda7fffff pref]
[ 0.203702] pci 0000:00:0e.0: PCI bridge to [bus 02]
[ 0.203705] pci 0000:00:0e.0: bridge window [io 0xb000-0xbfff]
[ 0.203709] pci 0000:00:0e.0: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.203715] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.203718] pci_bus 0000:00: resource 5 [mem 0x000a0000-0x000bffff]
[ 0.203720] pci_bus 0000:00: resource 6 [mem 0x60000000-0xfcffffffff]
[ 0.203723] pci_bus 0000:01: resource 1 [mem 0xfa900000-0xfe9fffff]
[ 0.203726] pci_bus 0000:01: resource 2 [mem 0xba800000-0xda7fffff pref]
[ 0.203730] pci_bus 0000:02: resource 0 [io 0xb000-0xbfff]
[ 0.203732] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.203816] NET: Registered protocol family 2
[ 0.204157] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.204482] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.204915] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.205152] TCP: reno registered
[ 0.205159] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.205233] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.205488] NET: Registered protocol family 1
[ 0.205869] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 22
[ 0.290220] ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 21
[ 0.370210] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 20
[ 0.370416] pci 0000:01:00.0: Boot video device
[ 0.370423] PCI: CLS 32 bytes, default 64
[ 0.370570] Unpacking initramfs...
[ 0.464290] Freeing initrd memory: 3236K (ffff88005fc97000 - ffff88005ffc0000)
[ 0.464451] microcode: AMD CPU family 0xf not supported
[ 0.464560] Scanning for low memory corruption every 60 seconds
[ 0.465261] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.479534] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.481578] zbud: loaded
[ 0.481785] VFS: Disk quotas dquot_6.5.2
[ 0.481858] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.482120] msgmni has been set to 2999
[ 0.482218] Key type big_key registered
[ 0.482413] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.482461] io scheduler noop registered
[ 0.482463] io scheduler deadline registered (default)
[ 0.482512] io scheduler cfq registered
[ 0.482688] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.482710] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.482841] GHES: HEST is not enabled!
[ 0.482924] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.503487] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 0.524026] 00:0d: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 0.524343] Linux agpgart interface v0.103
[ 0.524401] rtc_cmos 00:01: RTC can wake from S4
[ 0.524562] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[ 0.524601] rtc_cmos 00:01: alarms up to one year, y3k, 114 bytes nvram
[ 0.524617] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.524839] TCP: cubic registered
[ 0.524845] IPv6: Loaded, but administratively disabled, reboot required to enable
[ 0.524849] NET: Registered protocol family 17
[ 0.525165] registered taskstats version 1
[ 0.525574] Magic number: 6:546:636
[ 0.525730] rtc_cmos 00:01: setting system clock to 2014-11-06 14:37:08 UTC (1415284628)
[ 0.525790] PM: Hibernation image not present or could not be loaded.
[ 0.529043] Freeing unused kernel memory: 1136K (ffffffff818d8000 - ffffffff819f4000)
[ 0.529053] Write protecting the kernel read-only data: 8192k
[ 0.534311] Freeing unused kernel memory: 944K (ffff880001514000 - ffff880001600000)
[ 0.536542] Freeing unused kernel memory: 408K (ffff88000179a000 - ffff880001800000)
[ 0.552237] random: systemd-tmpfile urandom read with 1 bits of entropy available
[ 0.560351] systemd-udevd[39]: starting version 216
[ 0.592052] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.592059] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.592875] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.596938] Floppy drive(s): fd0 is 1.44M
[ 0.614213] ACPI: bus type USB registered
[ 0.614265] usbcore: registered new interface driver usbfs
[ 0.614281] usbcore: registered new interface driver hub
[ 0.614967] FDC 0 is a post-1991 82077
[ 0.625659] SCSI subsystem initialized
[ 0.633113] libata version 3.00 loaded.
[ 0.633845] sata_nv 0000:00:0a.0: version 3.5
[ 0.634191] ACPI: PCI Interrupt Link [LTID] BIOS reported IRQ 0, using IRQ 22
[ 0.634194] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 22
[ 0.635580] usbcore: registered new device driver usb
[ 0.636718] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.637213] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.637384] ohci-pci: OHCI PCI platform driver
[ 0.637732] ehci-pci: EHCI PCI platform driver
[ 0.647435] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 19
[ 0.647607] scsi0 : sata_nv
[ 0.652697] scsi1 : sata_nv
[ 0.652813] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xc800 irq 22
[ 0.652817] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xc808 irq 22
[ 0.653212] ohci-pci 0000:00:02.0: OHCI PCI host controller
[ 0.653223] ohci-pci 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 0.653279] ohci-pci 0000:00:02.0: irq 22, io mem 0xfebfd000
[ 0.685200] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.700074] firewire_ohci 0000:02:0b.0: added OHCI v1.0 device as card 0, 4 IR + 8 IT contexts, quirks 0x11
[ 0.712351] hub 1-0:1.0: USB hub found
[ 0.712367] hub 1-0:1.0: 4 ports detected
[ 0.712766] ohci-pci 0000:00:02.1: OHCI PCI host controller
[ 0.712776] ohci-pci 0000:00:02.1: new USB bus registered, assigned bus number 2
[ 0.712845] ohci-pci 0000:00:02.1: irq 21, io mem 0xfebfe000
[ 0.772298] hub 2-0:1.0: USB hub found
[ 0.772346] hub 2-0:1.0: 4 ports detected
[ 0.773212] ehci-pci 0000:00:02.2: EHCI Host Controller
[ 0.773228] ehci-pci 0000:00:02.2: new USB bus registered, assigned bus number 3
[ 0.773242] ehci-pci 0000:00:02.2: debug port 1
[ 0.773285] ehci-pci 0000:00:02.2: cache line size of 32 is not supported
[ 0.773315] ehci-pci 0000:00:02.2: irq 20, io mem 0xfebffc00
[ 0.790050] ehci-pci 0000:00:02.2: USB 2.0 started, EHCI 1.00
[ 0.790381] hub 3-0:1.0: USB hub found
[ 0.790395] hub 3-0:1.0: 8 ports detected
[ 0.880074] hub 1-0:1.0: USB hub found
[ 0.880086] hub 1-0:1.0: 4 ports detected
[ 0.970117] hub 2-0:1.0: USB hub found
[ 0.970134] hub 2-0:1.0: 4 ports detected
[ 0.970356] pata_amd 0000:00:08.0: version 0.4.1
[ 0.973849] scsi2 : pata_amd
[ 0.974094] scsi3 : pata_amd
[ 0.974162] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 0.974165] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 0.980098] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.110030] usb 3-1: new high-speed USB device number 2 using ehci-pci
[ 1.190443] ata3.00: ATA-6: IC35L120AVV207-0, V24OA63A, max UDMA/100
[ 1.190446] ata3.00: 241254720 sectors, multi 16: LBA48
[ 1.190651] ata3.01: ATA-7: Hitachi HDT725032VLAT80, V54OA42A, max UDMA/133
[ 1.190654] ata3.01: 625142448 sectors, multi 16: LBA48
[ 1.190664] ata3: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6c7c000) ACPI=0x3f01f (20:15:0x1f)
[ 1.190668] ata3: nv_mode_filter: 0x7f39f&0x7f39f->0x7f39f, BIOS=0x7f000 (0xc6c7c000) ACPI=0x7f01f (20:15:0x1f)
[ 1.200168] firewire_core 0000:02:0b.0: created device fw0: GUID 00e0180000b91545, S400
[ 1.250375] ata3.00: configured for UDMA/100
[ 1.265023] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 1.265669] scsi4 : usb-storage 3-1:1.0
[ 1.265808] usbcore: registered new interface driver usb-storage
[ 1.290406] ata3.01: configured for UDMA/133
[ 1.310032] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.310260] scsi 2:0:0:0: Direct-Access ATA IC35L120AVV207-0 V24O PQ: 0 ANSI: 5
[ 1.310565] scsi 2:0:1:0: Direct-Access ATA Hitachi HDT72503 V54O PQ: 0 ANSI: 5
[ 1.380033] usb 3-2: new high-speed USB device number 3 using ehci-pci
[ 1.460029] tsc: Refined TSC clocksource calibration: 2210.758 MHz
[ 1.490267] ata4.00: ATAPI: PIONEER DVD-RW DVR-107D, 1.21, max UDMA/33
[ 1.490278] ata4: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc6c7c000) ACPI=0x701f (60:600:0x13)
[ 1.510193] ata4.00: configured for UDMA/33
[ 1.517016] scsi 3:0:0:0: CD-ROM PIONEER DVD-RW DVR-107D 1.21 PQ: 0 ANSI: 5
[ 1.530745] sd 2:0:1:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 1.530827] sd 2:0:1:0: [sdb] Write Protect is off
[ 1.530831] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.530860] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.530988] sd 2:0:0:0: [sda] 241254720 512-byte logical blocks: (123 GB/115 GiB)
[ 1.531050] sd 2:0:0:0: [sda] Write Protect is off
[ 1.531053] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.531145] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.536391] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 1.536403] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.536800] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 1.542997] usb-storage 3-2:1.0: USB Mass Storage device detected
[ 1.543072] sdb: sdb1
[ 1.543976] scsi5 : usb-storage 3-2:1.0
[ 1.567204] sd 2:0:1:0: [sdb] Attached SCSI disk
[ 1.575313] sda: sda1 sda2
[ 1.575840] sd 2:0:0:0: [sda] Attached SCSI disk
[ 1.660061] usb 3-3: new high-speed USB device number 4 using ehci-pci
[ 1.810652] hub 3-3:1.0: USB hub found
[ 1.810704] hub 3-3:1.0: 4 ports detected
[ 2.210057] usb 2-2: new low-speed USB device number 2 using ohci-pci
[ 2.261495] scsi 4:0:0:0: Direct-Access INTENSO USB 1100 PQ: 0 ANSI: 0 CCS
[ 2.263859] sd 4:0:0:0: [sdc] 15858688 512-byte logical blocks: (8.11 GB/7.56 GiB)
[ 2.264963] sd 4:0:0:0: [sdc] Write Protect is off
[ 2.264968] sd 4:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 2.266088] sd 4:0:0:0: [sdc] No Caching mode page found
[ 2.266143] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 2.270838] sd 4:0:0:0: [sdc] No Caching mode page found
[ 2.270891] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 2.271726] sdc: sdc1 sdc2
[ 2.275974] sd 4:0:0:0: [sdc] No Caching mode page found
[ 2.276035] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 2.276094] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[ 2.446613] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.458243] usbcore: registered new interface driver usbhid
[ 2.458250] usbhid: USB HID core driver
[ 2.459628] input: Logitech USB Mouse as /devices/pci0000:00/0000:00:02.1/usb2/2-2/2-2:1.0/0003:046D:C00C.0001/input/input1
[ 2.460237] hid-generic 0003:046D:C00C.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:02.1-2/input0
[ 2.465896] Switched to clocksource tsc
[ 2.514535] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 2.540869] scsi 5:0:0:0: Direct-Access Hama FlashPen 1.04 PQ: 0 ANSI: 0 CCS
[ 2.541837] sd 5:0:0:0: [sdd] 1003520 512-byte logical blocks: (513 MB/490 MiB)
[ 2.542457] sd 5:0:0:0: [sdd] Write Protect is off
[ 2.542461] sd 5:0:0:0: [sdd] Mode Sense: 23 00 00 00
[ 2.543083] sd 5:0:0:0: [sdd] No Caching mode page found
[ 2.543138] sd 5:0:0:0: [sdd] Assuming drive cache: write through
[ 2.546081] sd 5:0:0:0: [sdd] No Caching mode page found
[ 2.546131] sd 5:0:0:0: [sdd] Assuming drive cache: write through
[ 2.546968] sdd:
[ 2.549206] sd 5:0:0:0: [sdd] No Caching mode page found
[ 2.549255] sd 5:0:0:0: [sdd] Assuming drive cache: write through
[ 2.549305] sd 5:0:0:0: [sdd] Attached SCSI removable disk
[ 3.215911] systemd[1]: systemd 216 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD -IDN )
[ 3.216179] systemd[1]: Detected architecture 'x86-64'.
[ 3.233071] systemd[1]: Set hostname to <db1arch>.
[ 4.451586] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 4.452340] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 4.452470] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 4.452530] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 4.453076] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 4.453109] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 4.453152] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 4.453167] systemd[1]: Starting Paths.
[ 4.453440] systemd[1]: Reached target Paths.
[ 4.453453] systemd[1]: Starting Encrypted Volumes.
[ 4.453723] systemd[1]: Reached target Encrypted Volumes.
[ 4.453743] systemd[1]: Expecting device dev-sda2.device...
[ 4.453935] systemd[1]: Expecting device dev-disk-by\x2duuid-1be23119\x2d5515\x2d4480\x2da559\x2d696105f9cee4.device...
[ 4.454136] systemd[1]: Expecting device dev-disk-by\x2duuid-385efd17\x2d3905\x2d4b8f\x2d8ec8\x2d9419a38cfcb0.device...
[ 4.454332] systemd[1]: Starting Root Slice.
[ 4.461699] systemd[1]: Created slice Root Slice.
[ 4.461738] systemd[1]: Starting User and Session Slice.
[ 4.462302] systemd[1]: Created slice User and Session Slice.
[ 4.462320] systemd[1]: Starting Delayed Shutdown Socket.
[ 4.462665] systemd[1]: Listening on Delayed Shutdown Socket.
[ 4.462683] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 4.462993] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 4.463008] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 4.463307] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 4.463322] systemd[1]: Starting Journal Socket (/dev/log).
[ 4.463621] systemd[1]: Listening on Journal Socket (/dev/log).
[ 4.463637] systemd[1]: Starting LVM2 metadata daemon socket.
[ 4.463929] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 4.463954] systemd[1]: Starting udev Control Socket.
[ 4.464241] systemd[1]: Listening on udev Control Socket.
[ 4.464259] systemd[1]: Starting udev Kernel Socket.
[ 4.464547] systemd[1]: Listening on udev Kernel Socket.
[ 4.464579] systemd[1]: Starting Journal Socket.
[ 4.464874] systemd[1]: Listening on Journal Socket.
[ 4.464930] systemd[1]: Starting System Slice.
[ 4.465527] systemd[1]: Created slice System Slice.
[ 4.465560] systemd[1]: Started File System Check on Root Device.
[ 4.465574] systemd[1]: Starting system-systemd\x2dfsck.slice.
[ 4.466125] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 4.475871] systemd[1]: Mounting Temporary Directory...
[ 4.486514] systemd[1]: Starting system-getty.slice.
[ 4.487508] systemd[1]: Created slice system-getty.slice.
[ 4.487590] systemd[1]: Mounting Huge Pages File System...
[ 4.488820] systemd[1]: Starting udev Coldplug all Devices...
[ 4.491503] systemd[1]: Starting Setup Virtual Console...
[ 4.494613] systemd[1]: Mounting Debug File System...
[ 4.497220] systemd[1]: Mounting POSIX Message Queue File System...
[ 4.557484] systemd[1]: Starting Set Up Additional Binary Formats...
[ 4.640820] systemd[1]: Started Load Kernel Modules.
[ 4.640879] systemd[1]: Starting Apply Kernel Variables...
[ 4.642456] systemd[1]: Mounting Configuration File System...
[ 4.643981] systemd[1]: Mounted FUSE Control File System.
[ 4.864249] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 4.865740] systemd[1]: Starting Journal Service...
[ 4.867779] systemd[1]: Started Journal Service.
[ 5.312956] EXT4-fs (sda1): re-mounted. Opts: data=ordered
[ 5.624022] systemd-udevd[140]: starting version 216
[ 6.289020] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 6.289034] ACPI: Power Button [PWRB]
[ 6.289120] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 6.289123] ACPI: Power Button [PWRF]
[ 6.352568] agpgart-amd64 0000:00:00.0: AGP bridge [10de/00e1]
[ 6.352584] agpgart-amd64 0000:00:00.0: aperture size 4096 MB is not right, using settings from NB
[ 6.352594] agpgart-amd64 0000:00:00.0: setting up Nforce3 AGP
[ 6.368450] agpgart-amd64 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[ 6.486856] parport_pc 00:05: reported by Plug and Play ACPI
[ 6.486927] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 6.587129] gameport gameport0: NS558 PnP Gameport is pnp00:0b/gameport0, io 0x200, speed 904kHz
[ 6.688852] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 6.689198] ACPI: PCI Interrupt Link [LKLN] enabled at IRQ 21
[ 6.728214] random: nonblocking pool is initialized
[ 6.988022] mousedev: PS/2 mouse device common for all mice
[ 7.210562] forcedeth 0000:00:05.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:11:d8:00:96:f1
[ 7.210572] forcedeth 0000:00:05.0: csum timirq gbit lnktim desc-v2
[ 7.210685] ACPI Warning: SystemIO range 0x0000000000005000-0x000000000000503f conflicts with OpRegion 0x0000000000005000-0x0000000000005004 (\_SB_.PCI0.SMBS.SMRG) (20131218/utaddress-258)
[ 7.210694] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 7.210750] i2c i2c-0: nForce2 SMBus adapter at 0x5040
[ 7.210837] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.304777] MCE: In-kernel MCE decoding enabled.
[ 7.310354] [Firmware Bug]: powernow-k8: No PSB or ACPI _PSS objects
[ 7.310416] powernow-k8: Make sure that your BIOS is up to date and Cool'N'Quiet support is enabled in BIOS setup
[ 7.388088] ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 20
[ 7.482978] ppdev: user-space parallel port driver
[ 7.492121] EDAC MC: Ver: 3.0.0
[ 7.682441] AMD64 EDAC driver v3.4.0
[ 7.720053] intel8x0_measure_ac97_clock: measured 50279 usecs (2472 samples)
[ 7.720064] intel8x0: clocking to 46862
[ 7.720952] EDAC amd64: DRAM ECC enabled.
[ 7.720961] EDAC amd64: K8 revE or earlier detected (node 0).
[ 7.721024] EDAC amd64: CS0: Double data rate SDRAM
[ 7.721026] EDAC amd64: CS1: Double data rate SDRAM
[ 7.721028] EDAC amd64: CS2: Double data rate SDRAM
[ 7.721029] EDAC amd64: CS3: Double data rate SDRAM
[ 7.721031] EDAC amd64: CS4: Double data rate SDRAM
[ 7.721032] EDAC amd64: CS5: Double data rate SDRAM
[ 7.721371] EDAC MC0: Giving out device to module amd64_edac controller K8: DEV 0000:00:18.2 (INTERRUPT)
[ 7.721411] EDAC PCI0: Giving out device to module amd64_edac controller EDAC PCI controller: DEV 0000:00:18.2 (POLLED)
[ 7.819219] systemd-udevd[148]: renamed network interface eth0 to enp0s5
[ 8.800850] nvidia: module license 'NVIDIA' taints kernel.
[ 8.800863] Disabling lock debugging due to kernel taint
[ 8.878778] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 18
[ 8.878854] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=none
[ 8.879632] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.123 Wed Jul 2 10:59:22 PDT 2014
[ 9.251351] Adding 2137224k swap on /dev/sda2. Priority:-1 extents:1 across:2137224k FS
[ 9.501409] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: data=ordered
[ 10.518296] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.788573] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 11.527802] systemd-journald[119]: Received request to flush runtime journal from PID 1
glxinfo | grep OpenGL
OpenGL vendor string: NVIDIA Corporation
OpenGL renderer string: GeForce 7600 GT/AGP/SSE2
OpenGL version string: 2.1.2 NVIDIA 304.123
OpenGL shading language version string: 1.20 NVIDIA via Cg compiler
OpenGL extensions:
OpenGL ES profile version string: OpenGL ES 2.0 NVIDIA 304.123 304.123
OpenGL ES profile shading language version string: OpenGL ES GLSL ES 1.00
OpenGL ES profile extensions:
lspci -v
00:00.0 Host bridge: NVIDIA Corporation nForce3 250Gb Host Bridge (rev a1)
Subsystem: ASUSTeK Computer Inc. K8N-E
Flags: bus master, 66MHz, fast devsel, latency 0
Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [44] HyperTransport: Slave or Primary Interface
Capabilities: [c0] AGP version 3.0
Kernel driver in use: agpgart-amd64
Kernel modules: amd64_agp
00:01.0 ISA bridge: NVIDIA Corporation nForce3 250Gb LPC Bridge (rev a2)
Subsystem: ASUSTeK Computer Inc. K8N-E
Flags: bus master, 66MHz, fast devsel, latency 0
00:01.1 SMBus: NVIDIA Corporation nForce 250Gb PCI System Management (rev a1)
Subsystem: ASUSTeK Computer Inc. K8N-E
Flags: 66MHz, fast devsel
I/O ports at 5080 [size=32]
I/O ports at 5000 [size=64]
I/O ports at 5040 [size=64]
Capabilities: [44] Power Management version 2
Kernel driver in use: nForce2_smbus
Kernel modules: i2c_nforce2
00:02.0 USB controller: NVIDIA Corporation CK8S USB Controller (rev a1) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. K8N-E
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:02.1 USB controller: NVIDIA Corporation CK8S USB Controller (rev a1) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. K8N-E
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:02.2 USB controller: NVIDIA Corporation nForce3 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. K8N-E
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20
Memory at febffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=0098
Capabilities: [80] Power Management version 2
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:05.0 Bridge: NVIDIA Corporation CK8S Ethernet Controller (rev a2)
Subsystem: ASUSTeK Computer Inc. K8N-E
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
I/O ports at ec00 [size=8]
Capabilities: [44] Power Management version 2
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:06.0 Multimedia audio controller: NVIDIA Corporation nForce3 250Gb AC'97 Audio Controller (rev a1)
Subsystem: ASUSTeK Computer Inc. Device 812a
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20
I/O ports at e800 [size=256]
I/O ports at e400 [size=128]
Memory at febfb000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Kernel driver in use: snd_intel8x0
Kernel modules: snd_intel8x0
00:08.0 IDE interface: NVIDIA Corporation CK8S Parallel ATA Controller (v2.5) (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. K8N-E
Flags: bus master, 66MHz, fast devsel, latency 0
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable)
[virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
[virtual] Memory at 00000370 (type 3, non-prefetchable)
I/O ports at ffa0 [size=16]
Capabilities: [44] Power Management version 2
Kernel driver in use: pata_amd
Kernel modules: pata_amd, pata_acpi, ata_generic
00:0a.0 IDE interface: NVIDIA Corporation nForce3 Serial ATA Controller (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. K8N-E
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
I/O ports at 09f0 [size=8]
I/O ports at 0bf0 [size=4]
I/O ports at 0970 [size=8]
I/O ports at 0b70 [size=4]
I/O ports at c800 [size=16]
I/O ports at c400 [size=128]
Capabilities: [44] Power Management version 2
Kernel driver in use: sata_nv
Kernel modules: sata_nv, pata_acpi, ata_generic
00:0b.0 PCI bridge: NVIDIA Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=10
Memory behind bridge: fa900000-fe9fffff
Prefetchable memory behind bridge: ba800000-da7fffff
Kernel modules: shpchp
00:0e.0 PCI bridge: NVIDIA Corporation nForce3 250Gb PCI-to-PCI Bridge (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=128
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fea00000-feafffff
Kernel modules: shpchp
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Flags: fast devsel
Capabilities: [80] HyperTransport: Host or Secondary Interface
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Address Map
Flags: fast devsel
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] DRAM Controller
Flags: fast devsel
Kernel driver in use: amd64_edac
Kernel modules: amd64_edac_mod
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Flags: fast devsel
Kernel driver in use: k8temp
Kernel modules: k8temp
01:00.0 VGA compatible controller: NVIDIA Corporation G73 [GeForce 7600 GT] (rev a2) (prog-if 00 [VGA controller])
Subsystem: CardExpert Technology Device 0401
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18
Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Memory at c0000000 (32-bit, prefetchable) [size=256M]
Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at fe9e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 3.0
Kernel driver in use: nvidia
Kernel modules: nouveau, nvidia
02:0b.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A8V/A8N/P4P800 series motherboard
Flags: bus master, medium devsel, latency 64, IRQ 19
Memory at feaff800 (32-bit, non-prefetchable) [size=2K]
I/O ports at bc00 [size=128]
Capabilities: [50] Power Management version 2
Kernel driver in use: firewire_ohci
Kernel modules: firewire_ohci
running browsers from a uterm shows only these console messages (nothing else):
firefox http://dennisbusch.de/software/refugeel … _rlGL.html
(process:489): GLib-CRITICAL **: g_slice_set_config: assertion 'sys_page_size == 0' failed
google-chrome-stable http://dennisbusch.de/software/refugeel … _rlGL.html
NVIDIA: could not open the device file /dev/nvidia0 (Operation not permitted).
NVIDIA: could not open the device file /dev/nvidia0 (Operation not permitted).
google-chrome-stable --ignore-gpu-blacklist http://dennisbusch.de/software/refugeel … _rlGL.html
NVIDIA: could not open the device file /dev/nvidia0 (Operation not permitted).
NVIDIA: could not open the device file /dev/nvidia0 (Operation not permitted).
chromium shows the same messages as google-chrome-stable does.
stat /dev/nvidia0
File: /dev/nvidia0
Size: 0 Blocks: 0 IO Block: 4096 character special file
Device: 5h/5d Inode: 10741 Links: 1 Device type: c3,0
Access: (0666/crw-rw-rw-) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2014-11-06 15:42:55.105702689 +0100
Modify: 2014-11-06 15:42:55.105702689 +0100
Change: 2014-11-06 15:42:55.105702689 +0100
Birth: -
That's all I know. Any ideas?

Still trying...but pretty much stumbling around in the dark here.
cat /proc/driver/nvidia/agp/host-bridge
Host Bridge: PCI device 10de:00e1
Fast Writes: Supported
SBA: Supported
AGP Rates: 8x 4x
Registers: 0x1f00421b:0x00000312
cat /proc/driver/nvidia/agp/gpu
Fast Writes: Supported
SBA: Supported
AGP Rates: 8x 4x
Registers: 0xff000e1b:0x1f004312
cat /proc/driver/nvidia/agp/status
Status: Enabled
Driver: AGPGART
AGP Rate: 8x
Fast Writes: Disabled
SBA: Enabled
Digging around the web I found how to enable fastwrites and did so by
creating a file /etc/modprobe.d/nvidia.conf
with this content:
options nvidia NVreg_EnableAGPSBA=1 NVreg_EnableAGPFW=1
after reboot, startx
cat /proc/driver/nvidia/agp/status
Status: Enabled
Driver: AGPGART
AGP Rate: 8x
Fast Writes: Enabled
SBA: Enabled
The problem of sluggish webgl performance persists though and the
browsers as described in the OP are still giving the same messages.
Here is some more data, maybe it's relevant...
cat /proc/driver/nvidia/params
EnableVia4x: 0
EnableALiAGP: 0
NvAGP: 3
ReqAGPRate: 15
EnableAGPSBA: 1
EnableAGPFW: 1
Mobile: 4294967295
ResmanDebugLevel: 4294967295
RmLogonRC: 1
ModifyDeviceFiles: 1
DeviceFileUID: 0
DeviceFileGID: 0
DeviceFileMode: 438
RemapLimit: 0
UpdateMemoryTypes: 4294967295
InitializeSystemMemoryAllocations: 1
UseVBios: 1
RMEdgeIntrCheck: 1
UsePageAttributeTable: 4294967295
EnableMSI: 0
MapRegistersEarly: 0
RegisterForACPIEvents: 1
RegistryDwords: ""
RmMsg: ""

User weblogic is not permitted to boot the server

Hi,
I am new to OES and after running the configtool, creating the ASIAuthorizationProvider and ASIRoleMapperProvider (both has Defaul Identity Directory: wls_dir and Application Deployment Parent: //app/policy/wls_app), binding the SSM, i get this error when starting the WLS admin server:
15:33:26.312 EVENT Starting Jetty/4.2.25
15:33:26.859 WARN!! Delete existing temp dir C:\BEA_HOME_10\ales32-ssm\wls-ssm\i
nstance\wls_ssm\work\jar_temp\Jetty__8000__ for WebApplicationContext[/,jar:file
:/C:/BEA_HOME_10/ales32-ssm/wls-ssm/webapp/arme.war!/]
15:33:30.515 EVENT Started WebApplicationContext[,ARMEService]
15:33:32.562 EVENT Started SocketListener on 0.0.0.0:8000
15:33:32.562 EVENT Started org.mortbay.jetty.Server@176bf9e
ARME is started now
<Mar 5, 2010 3:33:33 PM SGT> <Notice> <Security> <BEA-090082> <Security initiali
zing using security realm wls.>
<Mar 5, 2010 3:33:34 PM SGT> <Critical> <Security> <BEA-090404> <User weblogic i
s not permitted to boot the server; The server policy may have changed in such a
way that the user is no longer able to boot the server.Reboot the server with t
he administrative user account or contact the system administrator to update the
server policy definitions.>
<Mar 5, 2010 3:33:34 PM SGT> <Critical> <WebLogicServer> <BEA-000386> <Server su
bsystem failed. Reason: weblogic.security.SecurityInitializationException: User
weblogic is not permitted to boot the server; The server policy may have changed
in such a way that the user is no longer able to boot the server.Reboot the ser
ver with the administrative user account or contact the system administrator to
update the server policy definitions.
weblogic.security.SecurityInitializationException: User weblogic is not permitte
d to boot the server; The server policy may have changed in such a way that the
user is no longer able to boot the server.Reboot the server with the administrat
ive user account or contact the system administrator to update the server policy
definitions.
at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.do
BootAuthorization(Unknown Source)
at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.in
itialize(Unknown Source)
at weblogic.security.service.SecurityServiceManager.initialize(Unknown S
ource)
at weblogic.security.SecurityService.start(SecurityService.java:141)
at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)
Truncated. see log file for complete stacktrace
>
<Mar 5, 2010 3:33:34 PM SGT> <Notice> <WebLogicServer> <BEA-000365> <Server stat
e changed to FAILED>
<Mar 5, 2010 3:33:34 PM SGT> <Error> <WebLogicServer> <BEA-000383> <A critical s
ervice failed. The server will shut itself down>
<Mar 5, 2010 3:33:34 PM SGT> <Notice> <WebLogicServer> <BEA-000365> <Server stat
e changed to FORCE_SHUTTING_DOWN>
Stopping PointBase server...
PointBase server stopped.
from the WLS AdminServer.log:
####<Mar 5, 2010 3:33:05 PM SGT> <Info> <Socket> <SGBLM010> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1267774385687> <BEA-000436> <Allocating 3 reader threads.>
####<Mar 5, 2010 3:33:05 PM SGT> <Info> <Socket> <SGBLM010> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1267774385687> <BEA-000446> <Native IO Enabled.>
####<Mar 5, 2010 3:33:06 PM SGT> <Info> <IIOP> <SGBLM010> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1267774386531> <BEA-002014> <IIOP subsystem enabled.>
####<Mar 5, 2010 3:33:11 PM SGT> <Info> <Security> <SGBLM010> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1267774391656> <BEA-000000> <Starting OpenJPA 1.0.0.1>
####<Mar 5, 2010 3:33:17 PM SGT> <Info> <Security> <SGBLM010> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1267774397171> <BEA-090516> <The Authenticator provider has preexisting LDAP data.>
####<Mar 5, 2010 3:33:33 PM SGT> <Info> <Security> <SGBLM010> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1267774413421> <BEA-090516> <The CredentialMapper provider has preexisting LDAP data.>
####<Mar 5, 2010 3:33:33 PM SGT> <Info> <Security> <SGBLM010> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1267774413500> <BEA-090663> <The DeployableRoleMapper "com.bea.security.providers.authorization.asi.RoleProviderStub" implements the deprecated DeployableRoleProvider interface.>
####<Mar 5, 2010 3:33:33 PM SGT> <Info> <Security> <SGBLM010> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1267774413531> <BEA-090662> <The DeployableAuthorizer "com.bea.security.providers.authorization.asi.AuthorizationProviderStub" implements the deprecated DeployableAuthorizationProvider interface.>
####<Mar 5, 2010 3:33:33 PM SGT> <Info> <Security> <SGBLM010> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1267774413796> <BEA-090093> <No pre-WLS 8.1 Keystore providers are configured for server AdminServer for security realm wls.>
####<Mar 5, 2010 3:33:33 PM SGT> <Notice> <Security> <SGBLM010> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1267774413796> <BEA-090082> <Security initializing using security realm wls.>
####<Mar 5, 2010 3:33:34 PM SGT> <Critical> <Security> <SGBLM010> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1267774414234> <BEA-090404> <User weblogic is not permitted to boot the server; The server policy may have changed in such a way that the user is no longer able to boot the server.Reboot the server with the administrative user account or contact the system administrator to update the server policy definitions.>
####<Mar 5, 2010 3:33:34 PM SGT> <Critical> <WebLogicServer> <SGBLM010> <AdminServer> <main> <<WLS Kernel>> <> <> <1267774414234> <BEA-000386> <Server subsystem failed. Reason: weblogic.security.SecurityInitializationException: User weblogic is not permitted to boot the server; The server policy may have changed in such a way that the user is no longer able to boot the server.Reboot the server with the administrative user account or contact the system administrator to update the server policy definitions.
weblogic.security.SecurityInitializationException: User weblogic is not permitted to boot the server; The server policy may have changed in such a way that the user is no longer able to boot the server.Reboot the server with the administrative user account or contact the system administrator to update the server policy definitions.
     at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.doBootAuthorization(Unknown Source)
     at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initialize(Unknown Source)
     at weblogic.security.service.SecurityServiceManager.initialize(Unknown Source)
     at weblogic.security.SecurityService.start(SecurityService.java:141)
     at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)
     at weblogic.work.ExecuteThread.execute(ExecuteThread.java:200)
     at weblogic.work.ExecuteThread.run(ExecuteThread.java:172)
>
####<Mar 5, 2010 3:33:34 PM SGT> <Notice> <WebLogicServer> <SGBLM010> <AdminServer> <main> <<WLS Kernel>> <> <> <1267774414328> <BEA-000365> <Server state changed to FAILED>
####<Mar 5, 2010 3:33:34 PM SGT> <Error> <WebLogicServer> <SGBLM010> <AdminServer> <main> <<WLS Kernel>> <> <> <1267774414328> <BEA-000383> <A critical service failed. The server will shut itself down>
####<Mar 5, 2010 3:33:34 PM SGT> <Notice> <WebLogicServer> <SGBLM010> <AdminServer> <main> <<WLS Kernel>> <> <> <1267774414328> <BEA-000365> <Server state changed to FORCE_SHUTTING_DOWN>
####<Mar 5, 2010 3:33:34 PM SGT> <Info> <WebLogicServer> <SGBLM010> <AdminServer> <main> <<WLS Kernel>> <> <> <1267774414359> <BEA-000236> <Stopping execute threads.>
also, i just noticed that when staring OES admin server i get the following from the logs:
system_console.log:
2010-03-05 15:19:04,218 [JettySSLListener1-1] ERROR com.wles.soap.BLM.BlmBindingImpl - getUndistributedAttributeChanges has not been implemented properly.
2010-03-05 15:27:17,656 [Thread-31] WARN com.bea.security.ssl.axis.AxisClientSocketFactory - Error during SSL handshake; host: SGBLM010, port: 8,000.
2010-03-05 15:27:17,687 [Thread-31] ERROR com.bea.security.pdws.Distributor - unable to bind unbound arme
Communication Error:; nested exception is:
     javax.net.ssl.SSLHandshakeException: Error during SSL handshake; host: SGBLM010, port: 8,000.
2010-03-05 15:27:17,687 [Thread-31] ERROR com.bea.security.pdws.ARMEGroup - arme group '//bind/wls' error report, policyno = 52:
2010-03-05 15:27:17,687 [Thread-31] ERROR com.bea.security.pdws.ARMEGroup - arme 'asi.null.ARME.wls_ssm.asi.SGBLM010':
2010-03-05 15:27:33,015 [Thread-32] WARN com.bea.security.ssl.axis.AxisClientSocketFactory - Error during SSL handshake; host: SGBLM010, port: 8,000.
2010-03-05 15:27:33,015 [Thread-32] ERROR com.bea.security.pdws.Distributor - unable to bind unbound arme
Communication Error:; nested exception is:
     javax.net.ssl.SSLHandshakeException: Error during SSL handshake; host: SGBLM010, port: 8,000.
WLESWebLogic.wrapper.log:
INFO | jvm 1 | 2010/03/05 15:27:17 | Processing AxisFault, cause: javax.net.ssl.SSLHandshakeException: Error during SSL handshake; host: SGBLM010, port: 8,000.
INFO | jvm 1 | 2010/03/05 15:27:17 | Re-throwing the fault...
INFO | jvm 1 | 2010/03/05 15:27:18 | error.jsp: Client has closed the connection, error not reported to client.
INFO | jvm 1 | 2010/03/05 15:27:18 | error.jsp: The exception is: com.bea.wles.management.console.utils.NestedJspException: Connection reset by peer: socket write error
INFO | jvm 1 | 2010/03/05 15:27:33 | Processing AxisFault, cause: javax.net.ssl.SSLHandshakeException: Error during SSL handshake; host: SGBLM010, port: 8,000.
INFO | jvm 1 | 2010/03/05 15:27:33 | Re-throwing the fault...
although, it seems that the OES admin server is up since i am able to access the OES admin console.
i have tried playing around the policies to grant the "weblogic" the priviliges for an Admin but is still get the same issue. Although, when i try to distribute the changes in the policy, "ASI ( Policy for entire Oracle Entitlements Server system ) " still appears in the list of changes.
any thoughts on what the problem is? is there a way to force the distribution of the policy? maybe through the command prompt or other console?
Edited by: user9056644 on Mar 5, 2010 12:02 AM

Have you applied CP2 or CP3 to OES? There were enhancements that allows these policies to be scoped within an organization. I only ask to help guide you on distributing policies for the runtime WLS domain. The ASI domain is only for the admin. There should have been a set of resources and policies created as a result of running ConfigTool for your new instance (looks like you named it 'wls'). If no CP, it will be in DefaultApp next to ASI.
You have to distribute policies for 'wls' immediately following running ConfigTool before starting WebLogic or you will put it into a state where it can't be started. The corrective action is to remove the state.ck file under C:\BEA_HOME_10/ales32-ssm/wls-ssm/instance/wls_ssm/work/runtime, distribute policies, restart WebLogic.
If you need to re-run ConfigTool (after installing CP for instance), revert the following files:
<domain>/config/config.xml
<domain>/bin/startWebLogic.sh | .cmd
Revert from the no-ales backups created. Remove the instance folder under C:\BEA_HOME_10\ales32-ssm/wls-ssm/instance. You can then re-run ConfigTool if you have to.

Item category customizing issue(The item category 'SRTT' is not permitted

Hi guys:
I got a material product, the caterory of the product is created by myself.
I trid to add the product to my service order item, but the error message said ,"
<b>The item category 'SRTT' is not permitted for product 'BO_3000000018'.
Message no. CRM_ORDERADM_I507
Diagnosis
The item category SRTT is not allowed in Customizing for item category determination of the specified transaction type, or in the item category group of the product BO_3000000018.
System Response
The system does not allow the item to be processed further.
u can display the specified input options. Place the cursor in the document on the field Item category and choose F4 = input options</b>
I tried many item category but the same error kept jumping out.
does anybody know the solution? thanks!
best regards
Eric

Hi Eric
You nay have to set the item category determination properly.
Fileds are you chould have an entry which should be something like this
Trans type -
Item cat group---The item cat that has to appear in your doc.
for example:
TA -
Standard Group-----TAN
The Item category group field is in the one you have given in your material master.
Hope this helps you.
Alicia

Lync 2011 for Mac - "sign in failed, service not available"

I can't sign on to Lync 2011 for Mac at all. I'm running OS X 10.7.2, Lync 14.0.1 (so yes, I've installed the patch) and regardless of what else I do I get the message:
"Sign in to Microsoft Lync failed because the service is not available or you may not be connected to the internet."
Obviously I'm connected to the internet, I've checked the firewall settings and the 3 other troubleshooting articles on the Mac Lync site. I've deleted the "unknown" certificate from Keychain that some people talked about being the source of their
issues, but no luck. What's going on here?

Hi amoss,
Any update?
It may due to Root CA is not trusted.
You should trust the correct Root CA in the Keychain Access on your Mac machine.
In addition, provide this
troubleshooting guide for reference. Hope helps.
Noya Liu
TechNet Community Support

503 Service not available

Hi.
Could you help me ....
I modified a bsp to display a PDF file into a new popup window, and I tested into my quality server using SE80 transaction and with my portal application after and evething was OK but when a released the new BSP into production server the BSP crashed.
This is the error message that throws:
503 Service not Available
Erro 6
Version 6040
MOdule http_j2ee_mt.c
Line 795
Server EMKIOAIX103_CRP_00
Details Cannot reach external application server on localhost:50000
I explain you my program does it:
1.- the user chooses the a record into a Inbox
2.- IC display its data with BSP IRecReason
3.- the user chooses a Action link
4.- IC display a action PRINT PDF
5.- the user selects a print pdf
This is my code to EH_ONGO than create the PDF spool
METHOD EH_ONGO .
DATA: function_name TYPE rs38l_fnam,
        dummy(254)        TYPE c,
        ls_archive_index TYPE toa_dara,
        ls_orderadm_h     TYPE crmt_output_orderadm_h_com,
        ls_activity_h     TYPE crmt_output_activity_h_com,
        ls_lead_h         TYPE crmt_output_lead_h_com,
        ls_opport_h       TYPE crmt_output_opport_h_com,
        ls_orgman_h       TYPE crmt_output_orgman_h_com,
        lt_partner_h      TYPE crmt_output_partner_h_comt,
        ls_pricingdata_h TYPE crmt_output_pricingdata_h_com,
        ls_sales_h        TYPE crmt_output_sales_h_com,
        ls_shipping_h     TYPE crmt_output_shipping_h_com,
        lt_payplan_d_h    TYPE crmt_output_payplan_d_h_comt,
        ls_customer_h     TYPE crmt_output_customer_h_com,
        ls_cumulat_h     TYPE crmt_output_cumulat_h_com,
        lt_billing_h     TYPE   crmt_output_billing_h_comt,
        lt_cancel_h      TYPE   crmt_output_cancel_h_comt,
        lt_appointment_h TYPE   crmt_output_appointment_h_comt,
        lt_billplan_d_h TYPE   crmt_output_billplan_d_h_comt,
        lt_billplan_h    TYPE   crmt_output_billplan_h_comt,
        lt_status_d_h    TYPE   crmt_output_status_d_h_comt,
        lt_status_h      TYPE   crmt_output_status_h_comt,
        lt_srv_subject_h TYPE   crmt_output_srv_subject_h_comt,
        lt_srv_reason_h TYPE   crmt_output_srv_reason_h_comt,
        lt_srv_result_h TYPE   crmt_output_srv_result_h_comt,
        ls_acs_h         TYPE   crmt_acs_h_com,
        lt_orderadm_i    TYPE   crmt_output_orderadm_i_comt,
        lt_orgman_i      TYPE   crmt_output_orgman_i_comt,
        lt_pricingdata_i TYPE   crmt_output_pricingdata_i_comt,
        lt_pricing_i     TYPE   crmt_output_pricing_i_comt,
        lt_product_i     TYPE   crmt_output_product_i_comt,
        lt_sales_i       TYPE   crmt_output_sales_i_comt,
        lt_shipping_i    TYPE   crmt_output_shipping_i_comt,
        lt_schedlin_i    TYPE   crmt_output_schedlin_i_comt,
        lt_customer_i    TYPE   crmt_output_customer_i_comt,
        lt_partner_i     TYPE   crmt_output_partner_i_comt,
        lt_item_cstics_i TYPE   crmt_item_cstics_tab,
        lt_billing_i     TYPE   crmt_output_billing_i_comt,
        lt_cancel_i      TYPE   crmt_output_cancel_i_comt,
        lt_finprod_i     TYPE   crmt_output_finprod_i_comt,
        lt_ordprp_i      TYPE   crmt_output_ordprp_i_comt,
        lt_appointment_i TYPE   crmt_output_appointment_i_comt,
        lt_billplan_d_i TYPE   crmt_output_billplan_d_i_comt,
        lt_billplan_i    TYPE   crmt_output_billplan_i_comt,
        lt_orderadm_i_qt TYPE   crmt_output_orderadm_i_qt_comt,
        lt_orderadm_i_in TYPE   crmt_output_orderadm_i_in_comt,
        lt_schedlin_i_cf TYPE   crmt_output_schedlin_i_cf_comt,
        lt_status_i      TYPE   crmt_output_status_i_comt,
        lt_working_set_e_s_bbp TYPE /1cn/working_set_e_s_bbp_t,
        lv_language LIKE sy-langu,
        lo_order TYPE REF TO cl_doc_crm_order,
        lv_object_guid TYPE crmt_object_guid,
        lv_object_kind TYPE crmt_object_kind,
        lv_status TYPE jstat,
        lt_status TYPE TABLE OF jstat,
        lv_error_tab_wrk TYPE ssferror,
        ls_output_options TYPE ssfcompop.
DATA: IP_SMART_FORM Type     TDSFNAME,
      IO_APPL_OBJECT Type Ref To OBJECT,
     IO_APPL_OBJECT Type Ref to CL_DOC_CRM_ORDER_H,
      IO_PARTNER Type Ref to CL_PARTNER_PPF,
      IS_ARCHIVE_INDEX Type TOA_DARA,
      CT_ARCHIVE_INDEX_TAB Type TSFDARA,
      IS_ARCHIVE_PARAMETERS Type ARC_PARAMS,
      control_parameters TYPE ssfctrlop,
      IS_MAIL_APPL_OBJ Type SWOTOBJID,
      IS_MAIL_RECIPIENT Type SWOTOBJID,
      IS_MAIL_SENDER Type SWOTOBJID,
      IP_USER_SETTINGS type TDBOOL,
      ES_DOCUMENT_OUTPUT_INFO type SSFCRESPD,
      ES_JOB_OUTPUT_INFO type SSFCRESCL,
      ES_JOB_OUTPUT_OPTIONS type SSFCRESOP.
Resultado generado: Formato PDF
data: l_pdf_xstring type xstring,
      lt_lines       type table of tline,
      ls_line        type tline,
      l_pdf_len      type i,
      lv_exist       type n,
      output_data    type ssfcrescl,
      lp_proc_stat TYPE ppfdtstat.
Explanation: this method executes the action,
gets the medium, gets the log, reads the messages from
the log and gets the spool id from the messages.     JLARIN 27/DIC/06
DATA: lv_event TYPE REF TO cl_htmlb_event_tableview,
      lv_index TYPE int4,
      wa_action TYPE LINE OF crmt_action_table_tab,
      ls_action_obj TYPE REF TO if_action_ppf,
      lr_action TYPE REF TO cl_trigger_ppf,
      lr_medium type Ref to     if_medium_ppf,
     ls_action TYPE zcrmt_action,
      lv_spoolid TYPE symsgv.
DATA:
     grid   type ref to cl_crm_ic_gridlayout,
     GLOBAL_EVENT     type string.
data: lo_trigger type ref to CL_TRIGGER_PPF,
      lo_sfprint type ref to CL_SF_PRINT_PPF,
      lo_typed_context type ref to CL_CRM_IC_IRECACTIONPLAN_CTXT,
      lt_all_data type PPFSINPRRU.
data: lo_rp_rc type i.
DATA: lv_head_guid      TYPE crmt_object_guid.
DATA: adminh     TYPE REF TO cl_crm_ic_irecactionplan_cn02,
        guidstring TYPE string,
        guid       TYPE crmt_object_guid,
        action_obj   TYPE crmt_action_obj_tab,
        lv_object_id TYPE crmt_object_id.
   DATA: request_event TYPE REF TO cl_htmlb_event.
   DATA: event_data    TYPE REF TO if_htmlb_data.
   DATA: event_value type string.
    event_data = cl_htmlb_manager=>get_event_ex( request ).
    if event_data is bound.
      try.
          request_event ?= event_data.
        catch cx_sy_move_cast_error.
          clear request_event.
      endtry.
      event_value = event_data->event_id.
      translate event_value to lower case.             "#EC TRANSLANG
   endif.
   if event_value <> 'x1_x3_x17_x21_actionitems'.
      return.
   endif.
TRY.
create object lo_sfprint.
create object lo_trigger.
    lv_exist = 1.
Get the header GUID
    adminh = typed_context->btadminh.
    guidstring = adminh->get_actionitem( 'GUID' ).
    If guidstring is initial.
       return.
    endif.
    lv_head_guid = guidstring.
    CALL FUNCTION 'CRM_ORDERADM_H_READ_OW'
      EXPORTING
        iv_orderadm_h_guid     = lv_head_guid
      IMPORTING
        ev_object_id           = lv_object_id
      EXCEPTIONS
        admin_header_not_found = 1
        OTHERS                 = 2.
       CALL FUNCTION 'CRM_ACTION_GET_TOOLBAR_IL'
      EXPORTING
        iv_ref_guid     = lv_head_guid
        iv_ref_kind     = 'A'
      IMPORTING
        et_action_obj   = action_obj
        et_action_fld   = action_fld
      EXCEPTIONS
        parameter_error = 1
        error_occurred = 2
        error_message   = 3
        OTHERS          = 4.
    IF sy-subrc EQ 0.
      LOOP AT action_fld INTO wa_action where applkey = lv_object_id.
      ENDLOOP.
      IF sy-subrc EQ 0.
         ls_action_obj = wa_action-action.
         lv_exist = 0.
      ENDIF.
    ENDIF.
    if lv_exist is initial.
    CALL METHOD ls_action_obj->get_processing
     IMPORTING
       ei_processing = lr_medium.
    CALL METHOD lo_trigger->get_appl
      RECEIVING
        result = io_appl_object.
      call function 'CRM_ACTION_GET_APPL_OBJECT'
        exporting
          iv_ref_guid          = lv_head_guid
          iv_ref_kind          = 'A'
        IMPORTING
          EV_APPL_OBJECT       = io_appl_object.
    CALL METHOD lr_medium->execute
      EXPORTING
        io_appl_ref       = io_appl_object   "lo_appl_ref
      RECEIVING
        rp_status         = lp_proc_stat
      EXCEPTIONS
        missing_arguments = 1
        OTHERS            = 2.
ip_smart_form = lr_medium->get_smartform( ).
    ip_smart_form = 'ZIMPR_ORDEN_RASTREO'.
get the function name for this smart form
    CALL FUNCTION 'SSF_FUNCTION_MODULE_NAME'
      EXPORTING
        formname           = ip_smart_form
      IMPORTING
        fm_name            = function_name
      EXCEPTIONS
        no_form            = 1
        no_function_module = 2
        OTHERS             = 3.
determine the tables of the application
CALL FUNCTION 'CRM_OUTPUT_SINGLE_READ'
    EXPORTING
      iv_object                 = io_appl_object
      iv_smart_form             = ip_smart_form
      ir_partner                = io_partner
    IMPORTING
      es_output_orderadm_h      = ls_orderadm_h
      es_output_activity_h      = ls_activity_h
      es_output_lead_h          = ls_lead_h
      es_output_opport_h        = ls_opport_h
      es_output_orgman_h        = ls_orgman_h
      es_output_pricingdata_h   = ls_pricingdata_h
      es_output_sales_h         = ls_sales_h
      es_output_shipping_h      = ls_shipping_h
      et_output_partner_h       = lt_partner_h
      et_output_payplan_d_h     = lt_payplan_d_h
      es_output_customer_h      = ls_customer_h
      es_output_cumulat_h       = ls_cumulat_h
      et_output_billing_h       = lt_billing_h
      et_output_cancel_h        = lt_cancel_h
      et_output_appointment_h   = lt_appointment_h
      et_output_billplan_d_h    = lt_billplan_d_h
      et_output_billplan_h      = lt_billplan_h
      et_output_status_d_h      = lt_status_d_h
      et_output_status_h        = lt_status_h
      et_output_srv_subject_h   = lt_srv_subject_h
      et_output_srv_reason_h    = lt_srv_reason_h
      et_output_srv_result_h    = lt_srv_result_h
      es_output_acs_h           = ls_acs_h
      et_output_orderadm_i      = lt_orderadm_i
      et_output_orgman_i        = lt_orgman_i
      et_output_pricingdata_i   = lt_pricingdata_i
      et_output_pricing_i       = lt_pricing_i
      et_output_product_i       = lt_product_i
      et_output_sales_i         = lt_sales_i
      et_output_shipping_i      = lt_shipping_i
      et_output_schedlin_i      = lt_schedlin_i
      et_output_partner_i       = lt_partner_i
      et_item_cstics_i          = lt_item_cstics_i
      et_output_customer_i      = lt_customer_i
      et_output_billing_i       = lt_billing_i
      et_output_cancel_i        = lt_cancel_i
      et_output_finprod_i       = lt_finprod_i
      et_output_ordprp_i        = lt_ordprp_i
      et_output_appointment_i   = lt_appointment_i
      et_output_billplan_d_i    = lt_billplan_d_i
      et_output_billplan_i      = lt_billplan_i
      et_output_orderadm_i_qt   = lt_orderadm_i_qt
      et_output_orderadm_i_in   = lt_orderadm_i_in
      et_output_schedlin_i_cf   = lt_schedlin_i_cf
      et_output_status_i        = lt_status_i
      et_output_wrk_set_e_s_bbp = lt_working_set_e_s_bbp
      ev_language               = lv_language.
control_parameters-langu = sy-langu.
control_parameters-no_dialog = 'X'.
control_parameters-getotf    = 'X'.
call function to process smart form
CALL FUNCTION function_name
    EXPORTING
      archive_index        = is_archive_index
      archive_index_tab    = ct_archive_index_tab
      archive_parameters   = is_archive_parameters
      control_parameters   = control_parameters
      mail_appl_obj        = is_mail_appl_obj
      mail_recipient       = is_mail_recipient
      mail_sender          = is_mail_sender
      output_options       = ls_output_options
      user_settings        = ip_user_settings
      orderadm_h           = ls_orderadm_h
      activity_h           = ls_activity_h
      lead_h               = ls_lead_h
      opport_h             = ls_opport_h
      orgman_h             = ls_orgman_h
      partner_h            = lt_partner_h
      pricingdata_h        = ls_pricingdata_h
      sales_h              = ls_sales_h
      shipping_h           = ls_shipping_h
      payplan_d_h          = lt_payplan_d_h
      cumulat_h            = ls_cumulat_h
      customer_h           = ls_customer_h
      acs_h                = ls_acs_h
      billing_h            = lt_billing_h
      cancel_h             = lt_cancel_h
      appointment_h        = lt_appointment_h
      billplan_d_h         = lt_billplan_d_h
      billplan_h           = lt_billplan_h
      status_d_h           = lt_status_d_h
      status_h             = lt_status_h
      srv_subject_h        = lt_srv_subject_h
      srv_reason_h         = lt_srv_reason_h
      srv_result_h         = lt_srv_result_h
      orderadm_i           = lt_orderadm_i
      orderadm_i_qt        = lt_orderadm_i_qt
      orderadm_i_in        = lt_orderadm_i_in
      orgman_i             = lt_orgman_i
      pricingdata_i        = lt_pricingdata_i
      pricing_i            = lt_pricing_i
      product_i            = lt_product_i
      sales_i              = lt_sales_i
      schedlin_i           = lt_schedlin_i
      schedlin_i_cf        = lt_schedlin_i_cf
      shipping_i           = lt_shipping_i
      partner_i            = lt_partner_i
      item_cstics_i        = lt_item_cstics_i
      customer_i           = lt_customer_i
      billing_i            = lt_billing_i
      cancel_i             = lt_cancel_i
      finprod_i            = lt_finprod_i
      ordprp_i             = lt_ordprp_i
      appointment_i        = lt_appointment_i
      billplan_d_i         = lt_billplan_d_i
      billplan_i           = lt_billplan_i
      status_i             = lt_status_i
      working_set_e_s_bbp = lt_working_set_e_s_bbp
      language             = lv_language
    IMPORTING
      document_output_info = es_document_output_info
      job_output_info      = output_data
      job_output_options   = es_job_output_options
    EXCEPTIONS
      output_canceled      = 1
      parameter_error      = 2
      OTHERS               = 3.
    call function 'CONVERT_OTF'
      EXPORTING
        format                = 'PDF'
      IMPORTING
        bin_filesize          = l_pdf_len
        bin_file              = l_pdf_xstring
      TABLES
        OTF                   = OUTPUT_DATA-OTFDATA
        LINES                 = LT_LINES
      EXCEPTIONS
        err_max_linewidth     = 1
        err_format            = 2
        err_conv_not_possible = 3
        err_bad_otf           = 4
        others                = 5.
      IF SY-SUBRC = 0.
        DATA: lv_string TYPE string,
              lv_numguid(10) TYPE N.
        lv_string = lv_spoolid.
        lv_numguid = lv_object_id.
       CALL METHOD op_previewspool( iv_spoolid = lv_string ).
        me->op_previewspool( iv_spoolid     = lv_string
                             lv_pdf_xstring = l_pdf_xstring
                             lv_guid        = lv_numguid ).
      ENDIF.
    endif.
    CATCH cx_sy_move_cast_error.
ENDTRY.
ENDMETHOD.
<b>This part send the result to a new windows and refresh a main page, but thow a error 503 ...</b>
method OP_PREVIEWSPOOL .
*{   INSERT         CRDK902447                                        1
DATA: lv_url TYPE string.
DATA: cached_response TYPE REF TO if_http_response,
      new_navegator   TYPE REF TO CL_WB_NAVIGATOR_NEW_WINDOW,
      new_navigation   TYPE REF TO CL_BSP_NAVIGATION.
DATA: guid TYPE guid_32.
Resultado generado: Formato PDF
data: l_pdf_xstring type xstring,
        display_url    type string,
        pagina_url    type string,
        display_pag    type string,
        V_TARGET_URL   TYPE STRING,
        W_APP_NAME     TYPE STRING,
        l_pdf_len      type i.
DATA: out TYPE REF TO IF_BSP_WRITER,
        lv_out TYPE REF TO cl_BSP_WRITER,
        lv_context Type Ref to IF_BSP_PAGE_CONTEXT,
        lv_body type string,
        lv_body2 type string,
        lv_guidmem(10) type n,
        lv_doscmd(200),
        lv_pag   type xstring,
        lv_back(2) type n.
IF not lv_pdf_xstring is initial.
    CREATE OBJECT cached_response TYPE CL_HTTP_RESPONSE EXPORTING add_c_msg = 1.
    l_pdf_len = xstrlen( lv_pdf_xstring ).
    cached_response->set_data( data   = lv_pdf_xstring
                          length = l_pdf_len ).
    cached_response->set_header_field( name = if_http_header_fields=>content_type
                                       value = 'application/pdf' ).
     cached_response->set_header_field(
                        name = 'content-disposition'
                        value = 'attachment; filename = test.pdf' ).
    cached_response->set_status( code = 200 reason = 'OK' ).
    cached_response->server_cache_expire_rel( expires_rel = 180 ).
    CALL FUNCTION 'GUID_CREATE'
      IMPORTING
        ev_guid_32 = guid.
DATA:
    LV_HOST     TYPE STRING,     "Host name
    LV_PORT     TYPE STRING,     "Port Number
    LV_LOCAL_URL     TYPE STRING,     "URL (Relative to the Current Server)
    LV_ABS_URL     TYPE STRING,     "URL (Absolute, incl. Protocol, Host, Port)
    LV_PROTOCOL     TYPE STRING,     "Available Protocol
    LV_servidor     TYPE STRING.     "Available Protocol
Construct the Target URL
      CALL METHOD RUNTIME->CONSTRUCT_BSP_URL
        EXPORTING
          IN_PROTOCOL       = 'http'
          IN_APPLICATION_NS = RUNTIME->APPLICATION_NAMESPACE
          IN_APPLICATION    = 'crm_ic'
          IN_PAGE           = '**/crm_ic'
        IMPORTING
          OUT_ABS_URL       = V_TARGET_URL
          OUT_HOST          = LV_HOST
          OUT_PORT          = LV_PORT
          OUT_LOCAL_URL     = LV_LOCAL_URL
          OUT_PROTOCOL      = LV_PROTOCOL.
        CONCATENATE 'crm_ic' '/**/' INTO W_APP_NAME.
      REPLACE W_APP_NAME IN V_TARGET_URL WITH SPACE.
    CONCATENATE V_TARGET_URL '/' guid '.pdf' INTO display_url.
    cl_http_server=>server_cache_upload( url      = display_url
                                         response = cached_response ).
    lv_url = adapter->if_bsp_page~get_page_url( ).
    if LV_PORT is initial.
       concatenate 'http://' LV_HOST lv_url+0(61) 'default.do' into lv_url.
    else.
       concatenate 'http://' LV_HOST ':' LV_PORT lv_url+0(61) 'default.do' into lv_url.
    endif.
      lv_body2 = '<html><head><script language=JavaScript>'.
      concatenate lv_body2 'window.open("' display_url '"); ' INTO lv_body2.
      concatenate lv_body2 ' location.href = "' lv_url '"; </script></head>' INTO lv_body2.
      concatenate lv_body2 '<body></body></html>' INTO lv_body2.
     concatenate lv_body2 ' function back(){ history.back( ); } </script></head>' INTO lv_body2.
     concatenate lv_body2 '<body><a href="javascript:back();">regresar</a></body></html>' INTO lv_body2.
      response->append_cdata( data = lv_body2 ) .
      response->set_header_field( name = 'content-type'
                                  value = 'text/html' ). "#EC NOTEXT
      response->set_header_field( name = 'cache-control' value = 'max-age=0' ). "#EC NOTEXT
     response->set_header_field( name = 'Expires' value = '0' ). "#EC NOTEXT
      navigation->response_complete( ).
return.
ENDIF.
endmethod.

Using the search bar, it seems it's a proxy issue, but finding a simple solution did not seem apparent. Have you tried a reboot? To reboot, hold the power and home buttons at the same time for at least 10 seconds (hold past the swipe to shut down bar, should it appear) until the Apple Logo appears, then let go fo both buttons and your iPad will restart. Hopefully, this will solve the problem......

Windows Firewall Service Crashes on Windows Server 2012

Hello Team,
I am facing issues with Windows Firewall Service in new Windows 2012 R2 deployments. when i try to start the Firewall service it wont start and it throws an error message to check the system event logs for information
The Windows Firewall service terminated with the following service-specific error:
The data is invalid.
I deployed this OS on a VM running with latest VM tools and HW version which is running on ESXi 5.1 U1
2 GB RAM, 1 vCPU
OS deployed through ISO downloaded from MS portal and License activated through KMS system, performed a couple of reboots as well.
any advise on this issue? i am sure some of you might have also faced the same issue

1. VMware support forum and knowledge base may give you more specific advice.
2. Windows services may be dependent on another service(s). Analyze these dependences. Do it after you understand implications of VMware firewall function.
3. More detailed info from Event log is needed for analysis (Event ID, etc)
4. Hope you have connectivity configured correctly.
5. For firewall in VMware read the following article(s):
http://pubs.vmware.com/vsphere-51/index.jsp?topic=%2Fcom.vmware.vsphere.security.doc%2FGUID-52188148-C579-4F6A-8335-CFBCE0DD2167.html&__utma=207178772.2027713003.1393320147.1393320147.1393320147.1&__utmb=207178772.0.10.1393320147&__utmc=207178772&__utmx=-&__utmz=207178772.1393320147.1.1.utmcsr=google|utmccn=(organic)|utmcmd=organic|utmctr=(not%20provided)&__utmv=-&__utmk=174193441
Regards
Milos

Decimal Places are not Permitted for Chile Country

Hi All,
In OVA8 settings for Chile country at the field max.doc value, i am not able to use the decimals. getting error message as Decimlas are not permitted (Message no - 00011). checked OY04 - there is no decimals for Chile currency. checked - OY01 Dec.Pt. format as 1.234.567,89
For Argentina, Peru and Uruguay same settings has been done and i am able to save the decimal points in OVA8 at the field max.doc value.
Please let me know if there is any specifis settings for Chile or SAP NOTE
Thanks,
Mahesh

HI,
just looking at a brand-new ECC60 / EhP4 system where nobody changed OY04 settings.
I can find CLP (Chilean Peso) in the list with ' ' decimal places, so thats why there are no decimal places allowed.
Check again OY04, if you find an entry for CLP and NOTHING is maintained it means that ZERO dec. places are allowed.
If you find an entry in OY04 with a number of decimal places >0 than this decimal places are allowed.
If there is NO entry for a given currency then its used with 2 decimal places (SAP standard).
So OY04 is only for the currencies that should be treated different as SAP standard.
Best regards, Christian
Edited by: Christian Ortner on Feb 3, 2011 5:09 PM

Invoking a web service not created using oracle web service lib

Hi All,
I have a need to invoke my web service from oracle sql command. My web service not created using oracle web service library, but it is created using axis c++ libraries. Is it possible to do so,
Thanks in advance,
Regards,
Monica

In order to call out from the database process, is SQL (or PL/SQL) you need to generate some client code, that understand the details about the specific of the service you want to invoke and can produce the correct SOAP request. Once this proxy is uploaded in the Database, you can use it.
There is a set of Database Web services samples that should help you get started. You can also take a look at the developer's guide - see Developing a Web Service Client in the Database.
Hope it answers your question.
--eric

Error: Reason codes with automatic charge-off are not permitted here(F-28)

Hi All
I creted a reason code in obxl t-code and assigned a gl code in OBXL transaction code, But when I am trying to clear a payment with reason code in F-28, System is throwing the following error..Can some one tell me why i am getting this error?
Reason codes with automatic charge-off are not permitted here
Message no. F5605
Diagnosis
The reason code entered is designed to ensure that the payment difference amount is posted to an account specially set up for this purpose. Postings of this nature usually require additional specifications (e.g. tax code, business area). If the difference stems from a single open item, the necessary specifications can be taken from that item. In the case that led to this error message, however, the difference does not stem soley from one item, which means that this method cannot be used.
System Response
The reason code entered is not accepted.
Procedure
You can either select a different reason code, which would create a new open item for the customer or vendor OR write off the difference using the function Charge off diff.. This function either takes you into a pre-configured account assignment model or into the document overview. From here you can enter the required difference postings.

Hi Venkata,
It seems while entering the payment (partial payment / residual items) ... you are clearing multiple items with differences. (e.g. if the difference amount is $30, then may the difference consists of two invoices underpaid by $15 each). In this scenario, F-28 doesn't know which additional account assignment fields should be picked up ... hence the error.
First of all, to validate that this indeed is the case, try clearing a payment with the same reason code where difference can be attributed to a single invoice. If you still get an error, then there is some other problem.
Then, to take care of a the business scenario where the difference can indeed be due to multiple documents, select "charge off difference" option and create an entry to post the difference as necessary.
HTH,
Manish Patel
Sr. SAP Solutions Consultant

Error (23317) The operation Change properties of virtual machine is not permitted on a virtual machine that has shared virtual hard disks. Recommended Action The operation Change properties of virtual machine is not permitted on a virtual machine that h

Experts !
Error (23317)
The operation Change properties of virtual machine is not permitted on a virtual machine that has shared virtual hard disks.
Recommended Action
The operation Change properties of virtual machine is not permitted on a virtual machine that has shared virtual hard disks.
Is this limitation by design? If we have a shared VHDX between two VMs, then I am not able to change the VM properties from SCVMM.
SCVMM 2012 R2 with Windows Server 2012 R2 Hyper-V.
Appreciate any help !
Optimism is the faith that leads to achievement. Nothing can be done without hope and confidence.
InsideVirtualization.com

Hello,
that is a VMM issue.
If you did not deploy your virtual cluster from a VMM service template, VMM doesn't recognize the configuration.
Until MS got it fixed, you could use the workaround from system center central:
http://www.systemcentercentral.com/tag/shared-vhdx/
This posting is provided >AS IS< with no warranties.

Firewall service not permitting as it should

Similar Messages

Maybe you are looking for