First Business Server

I'm contemplating to put together a server for our business. We have around 25 employees, but only around 10 are in the office and using computers a lot. Pretty much everyone runs Apple, so I was thinking about setting up a server that would all people to backup over the network via Time Machine. I'm not sure yet how much disk space would be needed, as it depends on how long of backup is desired.
My question is how would I setup the HDD's to allow for a large overall storage space but made up from many HDD? If I allow each user to have 300GB of storage, that's around 3TB needed, so multiple HDD. Would I set them up as RAID0 to spread this out over multiple HDDs? What if I wanted to incorporate some redundancy (mirroring), such as RAID1? How would I accomplish this?
Thanks in advance!
James

jamgood96 wrote:
.:B:. wrote:
Yes, because wireless is half duplex as well.
jamgood96 wrote:
I'm on board with that logic.
This is slightly off what my original topic was, but since I'm looking at doing Time Machine backups over the network, is it completely unrealistic to expect people to do this over WiFi?
Totally.
Not only do you need a lot of bandwidth for it, you also need reliability, and security. Just like with Ethernet, the more people hop on a WLAN, the more bandwidth gets squeezed as it gets distributed. Except that a WLAN has way less headroom than Ethernet to cope with that.
So it sounds like I need to have people hard-wired to the network to do backups, or figure out a solution to backup only what is vital. As mentioned before, our company runs mostly Macs, with the occasional PC in the mix. What solutions are out there for creating backups to a main server that would work with both platforms?
On a separate note, getting back to the RAID/HDD portion of the discussion, would it behoove me to run the OS on a smaller, faster drive, and then have two larger drives setup in RAID 1 for storing data and backups?
Ironically, if all the files were being accessed from the server itself, it would never have to backup each of the clients.  For high throughput, wired is always better than wireless.  If you are using full duplex 100Mbps ethernet it would be 200Mbps at 25Mb/s, compared to 37.5Mb/s of the wireless before overhead which would almost be real close.  If you combined them with a little QoS, you could probably get a decent combination with both.  I don't know exactly how you are setup, but with the PC it could be a thin client with the ease to which Arch makes this, it would be a consideration.  What are your Macs (are they actually Intel Macs)?  You could use the same image.  Because there is also a PPC version of Arch.  There's probably reservations on using one system for everything, but this might ease the backup administration process.
Last edited by nomorewindows (2012-03-04 00:35:33)

Similar Messages

  • How to Install Coldfusion 8 64-bit on Small Business Server 2008 64-bit

    How to Install Coldfusion 8 64-bit on Small Business Server 2008 64-bit
    I ran Coldfusion 8 on SBS 2003 Premium for 6 months with no problems.  When we finally decided to cut over to SBS 2008, that’s when everything went to hell.  I tried for weeks to get Coldfusion 8 to install properly on the new SBS 2008 64-bit box.  During the course which, I found bits and pieces of information for Vista 64-bit and Windows Server 2008 64-bit installations.  There are some distinct differences, however, with SBS 2008 since it runs core Web applications like OWA, RWW and Companyweb.  After countless unsuccessful attempts, one of which completed corrupted the box, I found the solution.
    I have attempted in this white paper to detail the steps to assist others who may be in a similar situation.  I don’t make any warranty for the information, but so long as you follow the steps carefully you should be fine.  BTW, for those of you who say Adobe offers free technical support for licensed users, that’s not entirely true.  Like I said, I purchased CF8 and originally installed it on an SBS 2003 Premium box.  After we cut over to SBS 2008 and encountered problems, Adobe wouldn’t provide any technical support without charging.  Moreover, based on my initial conversations with Adobe’s technical team, no one seemed to know much about running 64-bit on SBS.
    From my understanding, only two versions of Coldfusion 8 can be installed in 64-bit: Enterprise and Developer.  The “normal” install (which I paid a grand for) can only be deployed in 32-bit mode – gee, THANKS Adobe!  By the way, in Developer mode only two distinct IPs can access the site in addition to the localhost.  Any additional IPs will result in a CFML error message stating that the maximum number of IPs have been exceeded.  At any rate, take your time and follow the steps to achieve a successful installation. 
    PRE-INSTALLATION TASKS
    Back Up SBS
    It’s always a good practice to backup your server before deploying any kind of major system changes.  Although this step is optional, I recommend it in case you need to restore your server for any reason.  Bear in mind, if your system ever gets totally corrupted, you cannot restore back from the twice daily incremental backup images alone.  You will need a full backup with system recovery information to restore.  Here are the basic steps:
    Click: Start > Programs > Administrative Tools.  Right-click “Windows Server Backup” and choose “Run as administrator”.
    Click “Backup Once” under Actions in the right-hand pane.
    Choose the “Different Options” radio button under Backup Options.
    Choose the “Custom” radio button.  What we’re primarily interested in here is backing up the OS – not your data partitions or attached drives.
    Select the “SYSTEM (C)” checkbox, uncheck any others.  Also, ensure that the “Enable system recovery” checkbox is selected before continuing on.
    Under ‘Specify Destination Type’, I usually select the “Local drives” radio button and point it to a Terrabyte USB drive I use for backups.  You can point this to a tape drive, or select the “Remote shared folder” radio button if you map to a UNC path to store your backup images.  Just remember, make sure that whatever path you select can readily be accessed in the event of an emergency.  Also, make sure the “Verify after writing (recommended)” checkbox is selected.
    Under ‘Specified Advanced Option’, I usually select the “VSS full backup” radio button instead of the default since I don’t use a 3rd party backup product.  If like me you rely solely on SBS for your backups, choose the full backup option.
    Confirm everything and click “Backup”.  This process may take several hours depending on the size of your system.
    Verify ISAPI Filters:
    In IIS Manager, double-click the server instance in the left-hand pane.
    In the center pane under IIS, double click the “Modules” icon to verify that the ISAPI native modules are already installed for IIS.  If it’s set up correctly you should see two entries:
    IsapiFilterModule              %windir%\System32\inetsrv\filter.dll
    IsapiModule                        %windir%\System32\inetsrv\isapi.dll
    If either of these modules are missing, you will need to re-install these (google for a solution).
    Set Up Development Environment
    Create a directory for your CFML files outside of the default Windows location (e.g., default is usually C:\inetpub\wwwroot\).  For the purpose of our install, I created a directory on a separate disk called: D:\DEV.
    Copy and paste your CFML files and directories into the new DEV root Web directory.  This will eventually be the directory where the Coldfusion installer places the CFIDE and CFDOCS folders. 
    Open IIS Manager and double-click the server instance in the left hand pane.  Expand the “Sites” folder.  Right-click the Sites folder and select “Add Web Site”.
    Enter a name in the “Site Name” box (e.g., “test-site”).  You will notice that the system will automatically create a corresponding Application Pool with the same name.  NOTE: this is important to prevent conflicts between the DefaultAppPool (needed for SBS Web apps like OWA, RWW, etc.) and the application pool needed for Coldfusion to function properly in SBS 2008.
    Point the “Physical Path” to the directory you created in step #1 above (e.g., “D:\DEV”).
    Don’t worry about testing the connection.  If you click “Test Settings” you may receive a warning that IIS cannot verify access to path (D:\DEV).  Don’t worry about this for the time being.
    Under “Host name”, enter a DNS path to your site (e.g., “dev.test-site.com”).  Click “OK”.
    Configure Application Pools for Installation
    In IIS Manager, double-click the server instance in the left-hand pane.  Click on “Application Pools” to display the list of server application pools in the center pane.
    In the “Actions” pane on the right-hand side, click “Set Application Pool Defaults”.
    Change “Enable 32-Bit Applications” - the second item from the top – from “False” to “True”, and then click “OK”.  NOTE: if you skip this step, Coldfusion will not properly create the required mappings during the install. We will change this setting back after the installation completes – more on this later.
    Modify the application.host.config File for 64-Bitness
    Click: Start > Programs > Accessories.  Right-click “Notepad” and choose “Run as administrator”.
    Open the config file from within Notepad – default location: C:\Windows\System32\inetsrv\config\applicationHost.config
    Do a search and change this one line from:
    <add name="PasswordExpiryModule" image="C:\Windows\system32\RpcProxy\RpcProxy.dll" />
    To this:
    <add name="PasswordExpiryModule" image="C:\Windows\system32\RpcProxy\RpcProxy.dll" preCondition="bitness64" />
    Restart the IIS Admin service.
    Set HTTP Compression
    According to some threads I read, the http compression module can cause errors if you don’t disable it globally. To remedy this, perform the following:
    Click: Start > Programs > Accessories.  Right-click “Command Prompt” and choose “Run as administrator”.
    At the command prompt, change directory to intetsrv by typing: cd inetsrv
    Run the following command:
    C:\Windows\system32\inetsrv>appcmd.exe set config -section:system.webServer/httpCompression /-[name='xpress']
    This will turn off HTTP compression for all sites in IIS.
    In IIS Manager, double-click the server instance in the left-hand pane.  Double-click the “Compression” icon in the IIS section of the center pane.
    Uncheck all of the boxes, then click the “Apply” button under Actions in the right-hand pane.
    Recheck all of the boxes, then click the “Apply” button under Actions in the right-hand pane.
    Restart the IIS Admin service.  This should enable compression and coldfusion to work at the same time.
    NOTE: if for some reason you need to reverse this, run the following command from the command prompt:
    C:\Windows\system32\inetsrv\appcmd.exe set config -section:system.webServer/httpCompression /+[name='xpress',doStaticCompression='false',dll='%windir%\system32\inetsrv\suscomp.dll']
    INSTALLATION TASKS
    Download the 64-bit installation package from Adobe – filename: coldfusion-801-wind64.exe.
    Right-click the file and select “Run as administrator”.
    Accept the terms of the License Agreement.
    If you have an Enterprise license, enter it.  For our purposes, just click the “Developer Edition” checkbox.
    Select “Server configuration” – the default radio button.
    I deselected all subcomponents and can’t guarantee that you’ll arrive at the same results if you select additional items like “.NET Integrated Services”.  It should be fine, particularly if you install documentation.  My preference was to keep the install as plain vanilla as possible.
    Select the directory path for Coldfusion to install into – default is :C\Coldfusion
    THE NEXT TWO STEPS ARE CRITICAL TO YOUR SUCCESS.  Unselect “All IIS Websites” and select the “Configure specific IIS Website or another web server” radio button.  Click “Add”, and then select your test Web site (e.g., “test-site”) under “IIS Web Site”.  Hit “OK”.
    Do NOT use the default directory path for the CF Administrator location (e.g., default path: “C:\inetpub\wwwroot”).  Instead, point the installer to your new DEV root Web directory (e.g., “D:\DEV”).  The bottom line, you want the installer to place the CFIDE directory and files within this folder, alongside your other CFML files and folders.
    Enter an Administrator password.
    Choose to Enable RDS, or not.  I enable this by preference but it is not required.  This allows you to make updates to files using a CFML editor directly vs. having to move/FTP the files over if you’re working remotely.  Opponents to this argue that it’s potentially less secure, but for a lower environment I don’t see this as a major concern.
    Confirm everything to kick off the install.
    If all goes well you should see a message at the end stating that the install was successful.  I recommend you uncheck the box that asks you to open the CF Administrator in the default Web browser after the install.  NOTE: we will open it a different way during the post-installation tasks.  The worst thing that will happen if you forget to uncheck the box is that you might receive an error that the command prompt hung – not a big deal – just close it and move on to the next (final) steps.
    POST-INSTALLATION TASKS
    Verify CF Installation:
    The installation will create a new folder in your program group: Start > Programs > Adobe > Coldfusion 8.  The default “Administrator” link will not work because it points to the wrong path: http://127.0.0.1/CFIDE/administrator/index.cfm. The “127.0.0.1” or “localhost” path as you may recall in IIS, points by default to the “C:\inetpub\wwwroot” directory.  Our CFIDE files, however, are located within: D:\DEV.
    To bring up the CF Administrator logon page, open up a Web browser and replace the “http://127.0.0.1” part of the path with the DNS path name to your CF environment (e.g., http://dev.test-site.com/CFIDE/administrator/index.cfm).
    This should bring up the Coldfusion Administrator Login screen.  Enter in the Administrator password you created during the install to log in and configure your application server.
    Verify that your test-site renders correctly by typing in your test URL into a Web browser (e.g., http://dev.test-site.com).
    Fix Application Pool Defaults to Re-enable SBS Web Applications:
    At this point, Coldfusion Administrator and your test CMFL Web site should be working properly.  The problem is, default SBS Web applications like OWA, RWW and Companyweb will throw errors and fail to start.  Fortunately, this is easily remedied by performing the following steps:
    In IIS Manager, double-click the server instance in the left-hand pane.  Click on “Application Pools” to display the list of server application pools in the center pane.
    In the “Actions” pane on the right-hand side, click “Set Application Pool Defaults”.
    Change “Enable 32-Bit Applications” - the second item from the top – from “True” to “False” this time.  This should re-enable the SBS applications, which would otherwise result in 500 errors (e.g., OWA, RWW, Companyweb, etc.).  There is no need to restart IIS.
    Open a Web browser and test that you can once again connect to OWA, RWW and Companyweb successfully.
    In IIS click to highlight the application pool for your new site (e.g., “test-site”).  In the right-hand pane, click “Advanced Settings”.  Ensure that “Enable 32-Bit Applications” – second item from the top – is set to “True” for this application pool specifically.
    Lastly, jump up and down for joy!  Hopefully now, everything is working.  Best of luck!! ..Paul D (MCP).

    First, it would be a good idea for you to specify what distro of Linux you're using, as not all are supported by Adobe.
    Second, this is probably your problem right here:
    http://askubuntu.com/questions/40416/why-is-lib-libc-so-6-missing
    In a nutshell, CF expects the 32-bit version of libc.so.6 to be in /lib, but it's probably not. You might be able to modify the installer to point to the correct location for that file, or you might be able to create a symlink to the file - but as the above link describes, creating a symlink might have negative consequences.
    As for installing CF 8 64-bit, that's only available with Enterprise, not Standard. If you want CF Standard 64-bit, you need to upgrade to CF 9.
    Dave Watts, CTO, Fig Leaf Software

  • Warning: Palm OS Treos and Windows Small Business Server 2008

    If you use a Treo smartphone with the Palm operating system, beware:  it does not work with Microsoft Windows Small Business Server 2008.
    Palm acknowledges this failure and has no intention of fixing it. 
    There are at least two problems:
    (1) You must turn off all email security on the Exchange mail server to sync with Treos.
    (2) AutoSync locks up the Palm each time it occurs, and must be turned off.
    Here's the transcript of my chat w/tech support. After this, I spent a few hours on the phone and got the same answers.
    [12:35 AM] Gary says: Hello.
    [12:35 AM] Handoff connection active (1/5140).
    [12:35 AM] x says: Hi. Please see the question sent earlier.
    [12:36 AM] Gary says: Could you please be more specific about the issue?
    [12:37 AM] x says: Our Palms will not talk to Exchange Server 2007 unless all its security
    features are turned off. This is a problem with Palm/VersaMail. When will it be corrected?
    [12:38 AM] Gary says: Yes, that is true. I am sorry for the inconvenience this may have caused.
    [12:38 AM] Gary says: I am very sorry to inform you that currently we do not have any information on this.
    [12:39 AM] x says: Apology accepted and appreciated. But when will this be fixed?
    [12:40 AM] Gary says: Unfortunately we do not have any sort of update on this. I suggest you to post the
    feedback in the Palm Website.
    [12:41 AM] x says: Okay, next question:  Every AutoSync locks up the Palm, so we have to turn
    AutoSync off. Do you intend to rectify this problem?
    [12:42 AM] Gary says: I understand your concern. Is it happening with all the Palm devices?
    [12:42 AM] x says: Yes.
    [12:43 AM] Gary says: Do you receive any error message before locking up the Treo?
    [12:43 AM] x says: No.
    [12:46 AM] Gary says: Okay, as this happening with all the devices to me it looks like the issue should be
    diagnosed closely to find the root cause. Was this happening with the Exchange Sever 2003?
    [12:46 AM] x says: No
    [12:46 AM] Gary says: So, the AutoSync feature is Locking the device from the day you upgraded to the
    Exchange Sever 2007.
    [12:46 AM] Gary says: Am I correct?
    [12:47 AM] x says: yes.
    [12:48 AM] Gary says: Okay, as this is the issue related to the sync with the Exchange Server 2007 and the
    AutoSync to find out the root cause I will escalate this issue to our escalation channel which is our Voice
    Support Team.
    [12:48 AM] Gary says:
    I will provide you all the information and guide you in the correct direction to address this issue.
    [12:48 AM] Gary says:
    I suggest you to get in touch with the Voice Support and I am sure they will fix the issue.
    [12:49 AM] Gary says:
    I will provide you a Service Request, when contacting the Voice Support, provide this Service Request Id and you will get a free Technical Support.
    [12:51 AM] Gary says: Please provide me your Last name, First name, complete address, phone number,Email address, date and place of purchase of device and serial number of the device to create a Service Request Number.
    [12:51 AM] x says: Of course I provided all this when I logged in, but here it is again:....
    [12:54 AM] Gary says: Thank you for providing all the information.I need 5 minutes to register the device and create a Service Request.
    [12:55 AM] x says: Thanks for your help, and confirmation of the incomprehensible failure to support Exchange Server 2007.  We're this close to dumping these things if this is the kind of tech support Palm intends to provide.
    [1:00 AM] Gary says: Thanks for staying on hold: I am sorry for the delay. I can understand the inconvenience you are facing.
    [1:01 AM] Gary says: Based on the information you provided, I created a service request for you in our database.  The Service Request number is : 1-51558238041
    [1:01 AM] x says: Will I get an email?
    [1:01 AM] Gary says: Using this service request number, you need to contact our Voice Support department.  Voice Support Department number is 877-426-3777. Voice support will be available from  5:00AM to 9:00PM (PST) on weekdays and from 8am - 5pm PST on weekends.Please note down the above given Service Request Number and Voice Support Number or else you will lose this information once the chat session is closed.
    [1:02 AM] Gary says: Yes, I will email this chat session to you.
    [1:02 AM] Gary says: Is there anything else I can assist you with today?
    Post relates to: Treo 755p (Sprint)

    The problem is the default security profile isn't compatible. You can go into the Power shell command line and remove the default activesync mailbox policy.
    Post relates to: None

  • Windows Small Business Server 2008 shutdown 180days 38 4

    Hello to everyone, 
    I'm trying to solve a problem in a friend server.
    i'm working on a Small Business Server 2008, it's a DC, NO sharepoint, NO Exchange (there is another software), NO DHCP (firewall do it), WINS and DNS enabled.
    Some days agoo Server has shutdown and in event viewer i found this 2 errors:
    38 and 4
    Event ID 38:
    "The Additional Server Count Check detected a condition in your environment that is out of compliance with the licensing policy. This server will be automatically shut down if the issue is not corrected in 68 day(s) 19 hour(s) 30 minute(s). Please look
    for additional events for Additional Server Count Check to troubleshoot."
    Event ID 4:
    "The Additional Server Count Check in the Licensing component did not pass because error 0x8007200a occurred in function f1031 [PFVK]. 
    The specified directory service attribute or value does not exist.
    I tried slmgr.vbs -dli and it's Licensed correctly.
    So i ran dcdiag /q and i've seen many errors like this:
    EventID: 0x0000168F
    Deleting dynamic of the DNS record '_kerberos._tcp.dc._msdcs.dominio.local. 600 IN SRV 0 100 88 server.dominio.local. 'failed on the following DNS server.
    I ran dcdiag /fix but problem still remains. 
    I really don't know how to fix this issue...
    Anyone have an idea?
    I also thought to use, in the extreme case, -ream , like slmgr.vbs -rearm, but i don't know how many times i can rearm server.
    Thank you and have a nice day

    Here you are DCPromo Log, it's in Italian 'cause is an Italian Server, btw i can translate.
    Controllo dell'installazione dei file binari di Servizi di dominio Active Directory in corso...
    Installazione Servizi di dominio Active Directory
    Convalida dell'ambiente e dei parametri in corso...
    Impossibile creare una delega per questo server DNS perch‚ la zona padre autorevole non Š stata trovata oppure non esegue il server DNS Windows. Se si sta effettuando l'integrazione con un'infrastruttura DNS esistente, Š consigliabile creare manualmente una delega per il server DNS nella zona padre per garantire una risoluzione dei nomi affidabile dall'esterno del dominio nameserver.local. In caso contrario, non Š necessario eseguire alcuna operazione.
    Verranno eseguite le azioni seguenti:
    Configurare il server come primo controller di dominio Active Directory in una nuova foresta.
    Il nome del nuovo dominio Š nameserver.local e corrisponde anche al nome della nuova foresta.
    Il nome NetBIOS del dominio Š nameserver
    Livello di funzionalit… foresta: Windows Server 2003
    Livello di funzionalit… dominio: Windows Server 2003
    Sito: Default-First-Site-Name
    Opzioni aggiuntive:
    Controller di dominio di sola lettura: No
    Catalogo globale: S
    Server DNS: S
    Crea delega DNS: No
    Cartella database: C:\Windows\ntds
    Cartella file di registro: C:\Windows\ntds
    Cartella SYSVOL: C:\Windows\sysvol
    Il servizio Server DNS verr… configurato in questo computer.
    Il computer verr… configurato per l'utilizzo di questo server DNS come server DNS preferito.
    La password del nuovo amministratore di dominio Š identica alla password dell'amministratore locale di questo computer.
    Avvio in corso...
    Verifica della necessit… di installare Console Gestione Criteri di gruppo in corso...
    Premere CTRL+C per: Annulla
    Configurazione del computer locale per l'hosting di Servizi di dominio Active Directory
    Creazione della partizione di directory: CN=Schema,CN=Configuration,DC=nameserver,DC=local in corso. Oggetti rimanenti: 1585
    Creazione della partizione di directory: CN=Configuration,DC=nameserver,DC=local in corso. Oggetti rimanenti: 1250
    Creazione della partizione di directory: CN=Configuration,DC=nameserver,DC=local in corso. Oggetti rimanenti: 966
    Creazione della partizione di directory: CN=Configuration,DC=nameserver,DC=local in corso. Oggetti rimanenti: 739
    Creazione della partizione di directory: CN=Configuration,DC=nameserver,DC=local in corso. Oggetti rimanenti: 535
    Creazione della partizione di directory: CN=Configuration,DC=nameserver,DC=local in corso. Oggetti rimanenti: 367
    Creazione della partizione di directory: CN=Configuration,DC=nameserver,DC=local in corso. Oggetti rimanenti: 204
    Creazione della partizione di directory: CN=Configuration,DC=nameserver,DC=local in corso. Oggetti rimanenti: 57
    Creazione della partizione di directory: CN=Configuration,DC=nameserver,DC=local in corso. Oggetti rimanenti: 0
    Creazione di oggetti Servizi di dominio Active Directory nel controller di dominio Active Directory locale
    Impostazione delle informazioni sul criterio LSA
    Impostazione della radice del nome DNS del computer a nameserver.local
    Protezione in corso di machine\software\microsoft\windows
    Protezione in corso di machine\system\currentcontrolset\control
    Protezione in corso di machine\system\currentcontrolset\control\class
    Protezione in corso di machine\system\currentcontrolset\services
    Protezione in corso di c:\windows\system32\spool
    Operazione sul controller di dominio completata.
    Configurazione del servizio Server DNS nel computer in corso...
    Installazione di Servizi di dominio Active Directory completata in questo computer per il dominio nameserver.local.
    Questo controller di dominio Active Directory Š assegnato al sito Default-First-Site-Name. Ô possibile gestire i siti con lo strumento di amministrazione Siti e servizi di Active Directory.
    I controller di dominio Windows Server 2008 hanno un nuovo valore predefinito, pi— sicuro, per l'impostazione "Consenti algoritmi di crittografia compatibili con Windows NT 4.0". Il valore impedisce che "client" Microsoft Windows e non Microsoft SMB usino algoritmi di crittografia vulnerabili di stile NT 4.0 per stabilire sessioni su canale sicuro con controller di dominio Windows Server 2008. Ne consegue che operazioni o applicazioni che richiedono un canale sicuro gestito da controller di dominio Windows Server 2008 potrebbero non funzionare.
    Le piattaforme interessate dal cambiamento sono Windows NT 4.0, i "client" non Microsoft SMB e dispositivi NAS che non supportano algoritmi di crittografia pi— avanzati. Ci sono inoltre conseguenze per alcune operazioni in client che eseguono versioni di Windows precedenti a Vista con Service Pack 1, come l'aggiunta a un dominio effettuata dall'Utilit… di migrazione ad Active Directory o da Servizi di distribuzione Windows.
    Per ulteriori informazioni, vedere l'articolo 942564 della Microsoft Knowledge Base all'indirizzo http://go.microsoft.com/fwlink/?LinkId=104751.
    Ô necessario riavviare il computer per completare l'operazione.

  • Downgrading Windows 2013 R2 Essentials to Small Business Server

    I need to operate a Server and exchange for my small business. I purchased Windows Small Business Server 2008 Standard which included exchange and no one would help me set it up. So I was told to buy Windows 2012 R2 Essentials and downgrade to Small Business
    Server 2011 Essentials it includes exchange.
    I called Microsoft as my software is Retail from the Microsoft Store here in Redmond, WA.
    Everyone says a huge amount of conflicting information.
    1 - SBS 2011 Essentials does not contain exchange
    2- I need to convert as a downgrade to SBS 2011 Standard which I cant do
    3 - I need the install media and need to call the activation line first ..
    Please help. There is no media I can find out there but I need to do this ASAP.
    Your help would be appreciated.
    Thanks,
    Matt

    1 - SBS 2011 Essentials does not contain exchange
    - Correct, Essentials does not include Exchange. No version of Essentials OS includes Exchange.
    If you are in need of assistance to set this up, I might suggest you consider using office 365 for your email.
    Robert Pearman SBS MVP
    itauthority.co.uk |
    Title(Required)
    Facebook |
    Twitter |
    Linked in |
    Google+

  • Migration of Windows Small Business Server 2003 to Windows Server 2012 Essentials

    Hi,
    I am trying to migrate Windows Small Business Server 2003 to Windows Server 2012 Essentials by following the steps given in the link below:
    http://technet.microsoft.com/en-us/library/jj200112.aspx
    I have looked at other threads on the forum but none of them have been too helpful.
    The issue: When
    I run the Migration Preparation Tool on the Source Server, it runs successfully and does not report any errors. However, when I try installing Windows Server 2012 Essentials on the Destination Server, it displays an error that says 'Source
    Server not prepared for migration: After you run the Migration Preparation Tool successfully on your source Server, click retry'.
    The Source Server has 2 network adapters-one for the local network and the other for connection to the internet and the router is set as the default gateway this adapter.
    Since it is mentioned in the documentation - 'configure your Source Server to use one network adapter', I'm wondering if this is the issue and I need to make changes in this configuration? 
    On running the Microsoft IT Environment Health Scanner tool it
    reported an error - 'DNS Server listening on multiple addresses' and a warning ‘Domain Controller listening on multiple addresses’. Both point to the same solution KB 272294 (http://support.microsoft.com/kb/272294).
    But it did not remove the errors.
    Other steps performed:
    As per the steps, I performed a backup, installed recent service packs and synchronized the source server time with external source.
    On running the Best Practices Analyser. It shows 3 warnings.
    - The threshold for the Allocated Memory alert is set to the default value. However the server has more than 2 GB of RAM installed.
    - Microsoft Outlook Client not installed" Text="Microsoft Outlook Client is not installed in the ClientApps folder. You must run Windows SBS integrated setup.
    - The MSFW instance should use the latest available service pack for Microsoft SQL Server 2000. The MSFW instance should use the latest available service pack for Microsoft SQL Server 2000.
    I also ran the Ran netdiag.exe, dcdiag.exe commands
    and no failures were reported.
    The Event Viewer does not show any errors.
    Not sure to what extent these warnings would affect the migration. 
    Any help would be appreciated. Thanks!

    The SBS2003 needs to use one NIC only so you'll need to change that before starting. If it is the premium version and has ISA server installed, that will need to be removed first.  See:
    http://blogs.technet.com/b/sbs/archive/2011/07/01/sbs-2011-standard-migrations-keys-to-success.aspx
    -- Al

  • Business Server exception: attempt to establish connection failed.

    Hi.
    I'm a total newbie to the BPA Suite, but I have experience with other tool sets like MEGA. I've downloaded and installed an evaluation copy of version 10.1.3.4 of the tool.
    I'm working through the Business Process Architect Quick Start Guide, going through the sample Quote to Cash process. Everything is progressing relatively well as I go through the document (except that the QuoteToCash project is already loaded in the LOCAL business repository without me having to load it separately), until I get to the first simulation.
    When I go to the Simulation module, I get an error: "Server access exception: Business Server exception: attempt to establish connection failed."
    I don't know what's wrong, but there are a couple of things I'm thinking about. One is that I didn't install XE separately, so I think that I'm just using the default Oracle Lite instance that gets installed with the tool. Another is that my account is configured without administrator privileges, so I generally have to run installers as a separate user with administrator privileges to get things to work.
    Any suggestions would be greatly appreciated!
    Thanks.

    It might be bad form to answer your own question, but after further experimentation, I think that it's a permissions problem.
    I repeated the installation on another (virtual) machine on an account that is an administrator, and I can simulate the Process Order process as described in the Quick Start Guide to my heart's content.
    Now, the second machine isn't configured exactly the same as the first machine, so there could be other underlying or contributing factors. But I'm un-stuck for now.
    I just thought I'd share what I found. Thanks.

  • Business Server Page (BSP) error - CX_FQDN

    Hi All,
    I configured FDQN and Maintain SICF services in Solution Manager and still I am getting the following error:- Any help will be appreciated.
    Business Server Page (BSP) error
    What happened?
    Calling the BSP page was terminated due to an error.
    SAP Note
    The following error text was processed in the system:
    Die URL enthu00E4lt keine vollstu00E4ndige Domainangabe (prdr01d3801 statt prdr01d3801.<domain>.<ext>).
    Exception Class CX_FQDN
    Error Name 
    Program CX_FQDN=======================CP
    Include CX_FQDN=======================CM002
    ABAP Class CX_FQDN
    Method CHECK
    Line 10 
    Long text -
    Error type: Exception
    Your SAP Business Server Pages Team
    Please  see my ICM parameters in the server.
    ICM Parameter                                                                               
    Services                                                                      
    icm/server_port_0     = PROT=HTTP,PORT=8001                                   
    icm/server_port_1     = PROT=SMTP,PORT=0                                                                               
    Hard limits                                                                   
    icm/max_services               = 30                                           
    icm/listen_queue_len           = 512                                          
    icm/req_queue_len              = 500                                          
    icm/max_conn                   = 500                                          
    icm/max_sockets                = 2048                                                                               
    Thread handling                                                               
    icm/min_threads                = 10                                           
    icm/max_threads                = 50                                           
    icm/min_spare_threads          = 3                                                                               
    Tracing and statistic                                                         
    rdisp/TRACE                    = 1                                            
    icm/tracefile                  = dev_icm                                      
    icm/log_level                  = 0                                            
    icm/stat_level                 = 1                                            
    icm/security_log               = LOGFILE=dev_icm_sec,MAXSIZEKB=500            
    icm/accept_remote_trace_level  = 0                                                                               
    Monitoring                                                                    
    icm/ccms_monitoring            = 1                                            
    icm/ccms_refresh_rate (sec.)   = 30                                                                               
    Timeout handling                                                              
    icm/keep_alive_timeout (sec.)  = 60                                           
    icm/conn_timeout (msec.)       = 5000                                                                               
    HTTP settings                                                                 
    icm/HTTP/max_request_size_KB   = 102400                                       
    icm/HTTP/j2ee_0                = PREFIX=/,HOST=localhost,CONN=0-500,PORT=50100
    icm/HTTP/server_cache_0        = PREFIX=/, CACHEDIR=F:\usr\sap\S4P\DVEBMGS01\d
       ata\cache                                                                  
    icm/HTTP/admin_0               = PREFIX=/sap/admin,DOCROOT=F:\usr\sap\S4P\DVEB
       MGS01\data\icmanroot/admin,AUTHFILE=F:\usr\sap\S4P                         
    icm/HTTP/auth_0                = PREFIX=/,FILTER=SAP                                                                               
    HTTP(S) error handling                                                        
    is/HTTP/show_detailed_errors   = 1                                                                               
    HTTPS (SSL) settings                                                          
    icm/HTTPS/verify_client        = 1                                            
    ssf/name                       =                                              
    ssf/ssfapi_lib                 =                                              
    sec/libsapsecu                 =                                              
    ssl/ssl_lib                    =                                                                               
    Context Quotas                                                                
    icm/HTTP/context_quota         = 90%                                          
    icm/HTTPS/context_quota        = 90%                                          
    icm/SMTP/context_quota         = 90%                                                                               
    Memory Pipe settings                                                          
    mpi/total_size_MB              = 80                                           
    mpi/buffer_size                = 65536                                                                               
    J2EE settings                                                                 
    rdisp/j2ee_start               = 1                                            
    is/HTTP/default_root_hdl       = J2EE                                                                               
    Content Filter settings                                                       
    csi/enable                     = TRUE                                         
    csi/SAP/csa_lib                = F:\usr\sap\S4P\DVEBMGS01\exe\sapcsa.dll                                                                               
    Misc                                                                          
    icm/host_name_full             = prdr01d3801.abcd.ae                        
    icm/cancel_strategy            = cancel requests without session (stateless)  
    rdisp/plugin_auto_logout       = 1800                                         
    is/HTTP/virt_host_0            = :;                                         
    is/SMTP/virt_host_0            = :;

    Hi Eddy,
    Yes I did,  in the first instance I am getting the following error from  Internet Explorer while try to access the link http://prdr01d3801.abcd.ae:8001/sap/bc/bsp/sap/ai_proj_setup/start.htm?sap-client=100&sap-language=E
    Network Error (dns_unresolved_hostname)
    Your requested host "prdr01d3801.abcd.ae" could not be resolved by DNS. 
    For assistance, contact Customer Support.
    Regards

  • Connecting to Small Business Server 2003

    I have an iMac G5 connected to a Windows Small Business Server 2003 server.
    When we first set this up, there was some security toggle that had to be adjusted on the Windows server.
    Recently the server completely crashed and when it was set up again I can't now get access to files on the server. I can't find the Apple document that described which setting on the SBS 2003 configuration needed to be changed.
    Can anyone point me to those instructions?
    Thanks for the help!
    Sam*
    iMac G5 Rev. B   Mac OS X (10.4.6)   1.5 G Ram

    Hi Sam*
    Welcome Back to Apple Discussions!
    A couple of questions, do you have any PC's connecting to the shares okay?
    The Security tab on a folder lists all the users and their access level.
    The Sharing tab lists all the "sharing" permissions to a given directory.
    I usually always set this to Everyone and Full. I control access with the Security tab.
    The default setting for W2003 with shared directories is to have the sharing permissions set to read only.
    This is easy to overlook.
    If this is not your situation, please provide more info.
    Thank you.

  • 8.8 on MS Windows Small Business Server 2003

    Hi Experts,
    I would like to know whether can 8.8 works on MS Windows Small Business Server 2003?
    Is there any known issues to share?
    Thanks.

    Hi,
    You may search forum first. Such as:
    Re: SBO_Backup Service is not Running In SAP Business one 8.8
    Windows Small Business Server (SBS) 2003 problem.
    Thanks,
    Gordon

  • The number of client access licenses may be reset to five in Windows Small Business Server 2003

    Ran into an issue on the server after the power loss.
    My Client Access Licenses were reset to 5 with Maximum usage of 12. I have about 25 PC's and Server also hosts exchange, which now prevents users from accessing OWA and local profiles. After digging around and reading logs, I eliminated issue to the licensing.
    All the steps described in the  Article ID: 888818 do not work, since the licenses were never backed up in the first place. Resetting, did not help either, since it's looking for a file, we don't have.
    Additionally, the auto-populated solutions, were already tried with no success. 
    Please let me know if there is a way to restore licensing via original license key, provided on the machine, or I have to purchase it.
    Thank you for your time.
    The number of client access licenses may be reset to five in Windows Small Business Server 2003

    Any help here?  (especially the autolicstr.cpa file)
    Small Business Server 2003 - The Dreaded 5 CAL Reset Issue
    http://blog.chrisara.com.au/2006/09/small-business-server-2003-dreaded-5.html
    Merv Porter
    =========================

  • Migrating from Windows Small Business Server

    So I finally made the jump to an intel based MAC a couple months ago and have loved every minute of it. I am now in a position to move our office to a completely MAC office but I had some questions first.
    Currently we are running Windows Small Business Server and have 3 desktops in the office. The server is basically for file sharing. However all of us work from home as well and use Remote Desktop to get into our computers at work and work remotely from home. The main reason we need to dial into the office is to get to our Quickbooks accounting file and create invoices remotely.
    My questions are:
    1. If I were to go with and Apple server and Apple desktops is there a way for me to dial in remotely and access my computers at work similar to Remote Desktop?
    2. Can both MACs and PCs dial in to the Apple Server?
    3. Is anyone out there using a better solution to access a company Quickbooks file on the server? Our current setup is that we have to remote connect to a computer in the office that is networked to the server. Is there some sort of VPN solution that apple offers so the remote computers can dial directly into the server?
    Your help is appreciated. I am really looking forward to making my office and all MAC office!
    Mac Book Pro 17"   Mac OS X (10.4.6)   Intel Dual Core

    OS X Server has a VPN server built-in, it's doing both PPTP and L2TP, it's compatible with both Mac and Windows clients IF you have the server connected to directly Internet using a public IP or use PPTP.
    There is no "dial-in" support that let's you use POTS (standard telephone) modems built-in.
    The Remote Desktop client in every OS X (Panther/Tiger) machine can accept remote control from a (free) VNC application (like Chicken Of the VNC - you connect through the VPN first).
    But the fastest remote control setup (most responsive screen updates) would be controlling a Windows XP pro machine by using Microsofts Remote Desktop Client sw (free -or is it? You can download it from http://www.microsoft.com/mac/) from either a Mac or another Windows XP client.

  • Establishing Socket Connection to a slow or busy server

    Currently, I'm developing an AIM-based BOT application in Java and it requires establishing a socket connection to their free and public server (host: toc.oscar.aol.com, port: 9898).
    About 75% of the time a connection will be successfully established using this:
    oConnection = new Socket("toc.oscar.aol.com", 9898);
    25% of the time when a connection fails (timeout) is due to the server being too slow or busy to respond to the connection request; however, the server will eventually response within 40 to 60 seconds.
    Let me go into details with my findings when attempting to connect to the slow/busy server:
    For experimental purposes, I used the telnet command (via the DOS command prompt: "telnet toc.oscar.aol.com 9898"), the connection will be established usually within 40 to 60 seconds.
    As I said before, the BOT application is developed in a Java environment and when attempting to establish a connection (using Java's Socket), a timeout exception gets raised when it hits the 20-seconds mark. It tells me that the Java Socket has the timeout defaulted to 20-seconds.
    I am aware that we can define the timeout settings using Socket's "setSoTimeout(x)" method; however, it's only good for AFTER a connection is established.
    Now, to sum up my findings � it clearly shows that the DOS' telnet prompt has longer "wait time" before raising any exceptions. As far as Java Socket is concerned, if a connection is not established within 20 seconds, it raises the timeout exception.
    Is there a way to stretch the "wait time" or "timeout" to be longer than 20 seconds for when a socket connection is being attempted?
    Millions of thanks in advance,
    Chad W. Taylor

    Yes, I also tried that option but no cigar. That
    timeout value is an alternative way of using
    setSoTimeout(int).
    I don't think so.
    First the Java documentation would not make sense:
    public void connect(SocketAddress endpoint, int timeout)
    throws IOException
    Connects this socket to the server with a specified timeout value. A timeout of zero is interpreted as an infinite timeout. The connection will then block until established or an error occurs.
    Parameters:
    endpoint - the SocketAddress
    timeout - the timeout value to be used in milliseconds.
    Throws:
    IOException - if an error occurs during the connection
    SocketTimeoutException - if timeout expires before connecting
    IllegalBlockingModeException - if this socket has an associated channel, and the channel is in non-blocking mode
    IllegalArgumentException - if endpoint is null or is a SocketAddress subclass not supported by this socket
    Since: 1.4
    Second my tests indicate otherwise:
    public class Main {
    public static void main(String[] args) {
    try {
         Socket conn = new Socket();
         conn.connect(new InetSocketAddress(InetAddress.getByName("toc.oscar.aol.com"),9898), Integer.parseInt(args[0]));
         System.out.println("connected under " + args[0] + " seconds");
         conn.close();
    } catch (Exception e) {
         System.out.println("not connected in " + args[0] + " seconds");
         e.printStackTrace();
    Different runs show:
    connected under 120 seconds
    and
    not connected in 20 seconds
    java.net.SocketTimeoutException: connect timed out
         at java.net.PlainSocketImpl.socketConnect(Native Method)
         at java.net.PlainSocketImpl.doConnect(Unknown Source)
         at java.net.PlainSocketImpl.connectToAddress(Unknown Source)
         at java.net.PlainSocketImpl.connect(Unknown Source)
         at java.net.Socket.connect(Unknown Source)
         at Main.main(Main.java:21)
    I speculate that the "Connection Request Timeout"
    value is platform dependent because when I use a
    different machine, the request timeout is either
    longer or shorter than 20 seconds.
    That could well be the case.
    So the proper question would be -- where is the Java
    Socket borrowing the timeout value from? The settings
    in Winsock?
    That I don't know.
    Andreas
    Chad

  • OMServer.msi returns error 1603 when trying to upgrade first management server from Operations Manager 2012 SP1 to Operations Manager 2012 R2

    Hi All, looking for some assistance with the following issue.
    We are attempting to upgrade our Operations Manager 2012 SP1 environment to Operations Manager 2012 R2.
    We have completed all the pre-upgrade tasks detailed here
    http://technet.microsoft.com/en-us/library/dn249704.aspx
    We are then following the guidance detailed here regarding upgrading distributed management groups
    http://technet.microsoft.com/en-us/library/dn249721.aspx. The upgrade fails on the first management server with the following screen being displayed.
    OMServer.log file is as follows.
    === Verbose logging started: 22/01/2014 10:21:27 Build type: SHIP UNICODE 5.00.9200.00 Calling process: C:\Users\scomaction\AppData\Local\SCOM\Setup\SetupChainerUI.exe ===
    MSI (c) (78:34) [10:21:27:040]: Resetting cached policy values
    MSI (c) (78:34) [10:21:27:040]: Machine policy value 'Debug' is 0
    MSI (c) (78:34) [10:21:27:040]: ******* RunEngine:
    ******* Product: F:\InstallFiles\SCOMR2\Setup\AMD64\Server\OMServer.msi
    ******* Action:
    ******* CommandLine: **********
    MSI (c) (78:34) [10:21:27:040]: Client-side and UI is none or basic: Running entire install on the server.
    MSI (c) (78:34) [10:21:27:040]: Grabbed execution mutex.
    MSI (c) (78:34) [10:21:27:071]: Cloaking enabled.
    MSI (c) (78:34) [10:21:27:071]: Attempting to enable all disabled privileges before calling Install on Server
    MSI (c) (78:34) [10:21:27:071]: Incrementing counter to disable shutdown. Counter after increment: 0
    MSI (s) (D4:30) [10:21:27:082]: Running installation inside multi-package transaction F:\InstallFiles\SCOMR2\Setup\AMD64\Server\OMServer.msi
    MSI (s) (D4:30) [10:21:27:082]: Grabbed execution mutex.
    MSI (s) (D4:A0) [10:21:27:086]: Resetting cached policy values
    MSI (s) (D4:A0) [10:21:27:086]: Machine policy value 'Debug' is 0
    MSI (s) (D4:A0) [10:21:27:086]: ******* RunEngine:
    ******* Product: F:\InstallFiles\SCOMR2\Setup\AMD64\Server\OMServer.msi
    ******* Action:
    ******* CommandLine: **********
    MSI (s) (D4:A0) [10:21:27:175]: Machine policy value 'DisableUserInstalls' is 0
    MSI (s) (D4:A0) [10:21:27:181]: Note: 1: 2203 2: C:\Windows\Installer\inprogressinstallinfo.ipi 3: -2147287038
    MSI (s) (D4:A0) [10:21:27:190]: SRSetRestorePoint skipped for this transaction.
    MSI (s) (D4:A0) [10:21:27:192]: Note: 1: 1402 2: HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer 3: 2
    MSI (s) (D4:A0) [10:21:27:200]: File will have security applied from OpCode.
    MSI (s) (D4:A0) [10:21:27:234]: SOFTWARE RESTRICTION POLICY: Verifying package --> 'F:\InstallFiles\SCOMR2\Setup\AMD64\Server\OMServer.msi' against software restriction policy
    MSI (s) (D4:A0) [10:21:27:234]: SOFTWARE RESTRICTION POLICY: F:\InstallFiles\SCOMR2\Setup\AMD64\Server\OMServer.msi has a digital signature
    MSI (s) (D4:A0) [10:21:27:354]: SOFTWARE RESTRICTION POLICY: F:\InstallFiles\SCOMR2\Setup\AMD64\Server\OMServer.msi is permitted to run at the 'unrestricted' authorization level.
    MSI (s) (D4:A0) [10:21:27:354]: MSCOREE not loaded loading copy from system32
    MSI (s) (D4:A0) [10:21:27:360]: End dialog not enabled
    MSI (s) (D4:A0) [10:21:27:360]: Original package ==> F:\InstallFiles\SCOMR2\Setup\AMD64\Server\OMServer.msi
    MSI (s) (D4:A0) [10:21:27:360]: Package we're running from ==> C:\Windows\Installer\4b8344.msi
    MSI (s) (D4:A0) [10:21:27:371]: APPCOMPAT: Compatibility mode property overrides found.
    MSI (s) (D4:A0) [10:21:27:372]: APPCOMPAT: looking for appcompat database entry with ProductCode '{C92727BE-BD12-4140-96A6-276BA4F60AC1}'.
    MSI (s) (D4:A0) [10:21:27:372]: APPCOMPAT: no matching ProductCode found in database.
    MSI (s) (D4:A0) [10:21:27:378]: Machine policy value 'TransformsSecure' is 1
    MSI (s) (D4:A0) [10:21:27:379]: Machine policy value 'DisablePatch' is 0
    MSI (s) (D4:A0) [10:21:27:379]: Machine policy value 'AllowLockdownPatch' is 0
    MSI (s) (D4:A0) [10:21:27:379]: Machine policy value 'DisableLUAPatching' is 0
    MSI (s) (D4:A0) [10:21:27:379]: Machine policy value 'DisableFlyWeightPatching' is 0
    MSI (s) (D4:A0) [10:21:27:380]: APPCOMPAT: looking for appcompat database entry with ProductCode '{C92727BE-BD12-4140-96A6-276BA4F60AC1}'.
    MSI (s) (D4:A0) [10:21:27:380]: APPCOMPAT: no matching ProductCode found in database.
    MSI (s) (D4:A0) [10:21:27:380]: Transforms are not secure.
    MSI (s) (D4:A0) [10:21:27:380]: Note: 1: 2205 2: 3: Control
    MSI (s) (D4:A0) [10:21:27:380]: PROPERTY CHANGE: Adding MsiLogFileLocation property. Its value is 'C:\Users\scomaction\AppData\Local\SCOM\Logs\OMServer.log'.
    MSI (s) (D4:A0) [10:21:27:380]: Command Line: OM_INSTALLDIR=F:\Program Files\Microsoft System Center 2012 R2\Operations Manager SEND_CEIP_REPORTS=0 MU_SETTING=0 ROOT_MANAGEMENT_SERVER_PORT=5723 SC_DB_SERVER=SCOM-XXX-AG SCDATABASENAME=OperationsManager DW_DB_SERVER=SCOM-XXX-AG DWDATABASENAME=OperationsManagerDW REBOOT=ReallySuppress CURRENTDIRECTORY=C:\Users\scomaction\AppData\Local\SCOM\Setup CLIENTUILEVEL=3 MSICLIENTUSESEXTERNALUI=1 CLIENTPROCESSID=4472
    MSI (s) (D4:A0) [10:21:27:380]: PROPERTY CHANGE: Adding PackageCode property. Its value is '{58EFE971-58C1-4DBD-A400-A7607A745475}'.
    MSI (s) (D4:A0) [10:21:27:380]: Product Code passed to Engine.Initialize: ''
    MSI (s) (D4:A0) [10:21:27:380]: Product Code from property table before transforms: '{C92727BE-BD12-4140-96A6-276BA4F60AC1}'
    MSI (s) (D4:A0) [10:21:27:380]: Product Code from property table after transforms: '{C92727BE-BD12-4140-96A6-276BA4F60AC1}'
    MSI (s) (D4:A0) [10:21:27:380]: Product not registered: beginning first-time install
    MSI (s) (D4:A0) [10:21:27:380]: Product {C92727BE-BD12-4140-96A6-276BA4F60AC1} is not managed.
    MSI (s) (D4:A0) [10:21:27:380]: MSI_LUA: Credential prompt not required, user is an admin
    MSI (s) (D4:A0) [10:21:27:381]: PROPERTY CHANGE: Adding ProductState property. Its value is '-1'.
    MSI (s) (D4:A0) [10:21:27:381]: Entering CMsiConfigurationManager::SetLastUsedSource.
    MSI (s) (D4:A0) [10:21:27:381]: User policy value 'SearchOrder' is 'nmu'
    MSI (s) (D4:A0) [10:21:27:381]: Adding new sources is allowed.
    MSI (s) (D4:A0) [10:21:27:381]: PROPERTY CHANGE: Adding PackagecodeChanging property. Its value is '1'.
    MSI (s) (D4:A0) [10:21:27:381]: Package name extracted from package path: 'OMServer.msi'
    MSI (s) (D4:A0) [10:21:27:381]: Package to be registered: 'OMServer.msi'
    MSI (s) (D4:A0) [10:21:27:383]: Note: 1: 2262 2: AdminProperties 3: -2147287038
    MSI (s) (D4:A0) [10:21:27:383]: Machine policy value 'DisableMsi' is 1
    MSI (s) (D4:A0) [10:21:27:383]: Machine policy value 'AlwaysInstallElevated' is 0
    MSI (s) (D4:A0) [10:21:27:383]: User policy value 'AlwaysInstallElevated' is 0
    MSI (s) (D4:A0) [10:21:27:383]: Product installation will be elevated because user is admin and product is being installed per-machine.
    MSI (s) (D4:A0) [10:21:27:383]: Running product '{C92727BE-BD12-4140-96A6-276BA4F60AC1}' with elevated privileges: Product is assigned.
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Adding OM_INSTALLDIR property. Its value is 'F:\Program Files\Microsoft System Center 2012 R2\Operations Manager'.
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Adding ROOT_MANAGEMENT_SERVER_PORT property. Its value is '5723'.
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Modifying SC_DB_SERVER property. Its current value is 'OperationsManager'. Its new value: 'SCOM-XXX-AG'.
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Adding DW_DB_SERVER property. Its value is 'SCOM-XXX-AG'.
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Adding DWDATABASENAME property. Its value is 'OperationsManagerDW'.
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Adding REBOOT property. Its value is 'ReallySuppress'.
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Adding CURRENTDIRECTORY property. Its value is 'C:\Users\scomaction\AppData\Local\SCOM\Setup'.
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Adding CLIENTUILEVEL property. Its value is '3'.
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Adding MSICLIENTUSESEXTERNALUI property. Its value is '1'.
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Adding CLIENTPROCESSID property. Its value is '4472'.
    MSI (s) (D4:A0) [10:21:27:383]: Machine policy value 'DisableAutomaticApplicationShutdown' is 0
    MSI (s) (D4:A0) [10:21:27:383]: RESTART MANAGER: Disabled by MSIRESTARTMANAGERCONTROL property; Windows Installer will use the built-in FilesInUse functionality.
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Adding MsiSystemRebootPending property. Its value is '1'.
    MSI (s) (D4:A0) [10:21:27:383]: TRANSFORMS property is now:
    MSI (s) (D4:A0) [10:21:27:383]: PROPERTY CHANGE: Adding VersionDatabase property. Its value is '300'.
    MSI (s) (D4:A0) [10:21:27:395]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\AppData\Roaming
    MSI (s) (D4:A0) [10:21:27:396]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\Favorites
    MSI (s) (D4:A0) [10:21:27:398]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\Network Shortcuts
    MSI (s) (D4:A0) [10:21:27:399]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\Documents
    MSI (s) (D4:A0) [10:21:27:401]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\Printer Shortcuts
    MSI (s) (D4:A0) [10:21:27:402]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\Recent
    MSI (s) (D4:A0) [10:21:27:404]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\SendTo
    MSI (s) (D4:A0) [10:21:27:405]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\Templates
    MSI (s) (D4:A0) [10:21:27:405]: SHELL32::SHGetFolderPath returned: C:\ProgramData
    MSI (s) (D4:A0) [10:21:27:406]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\AppData\Local
    MSI (s) (D4:A0) [10:21:27:408]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\Pictures
    MSI (s) (D4:A0) [10:21:27:411]: SHELL32::SHGetFolderPath returned: C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Administrative Tools
    MSI (s) (D4:A0) [10:21:27:413]: SHELL32::SHGetFolderPath returned: C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Startup
    MSI (s) (D4:A0) [10:21:27:414]: SHELL32::SHGetFolderPath returned: C:\ProgramData\Microsoft\Windows\Start Menu\Programs
    MSI (s) (D4:A0) [10:21:27:415]: SHELL32::SHGetFolderPath returned: C:\ProgramData\Microsoft\Windows\Start Menu
    MSI (s) (D4:A0) [10:21:27:417]: SHELL32::SHGetFolderPath returned: C:\Users\Public\Desktop
    MSI (s) (D4:A0) [10:21:27:420]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\Start Menu\Programs\Administrative Tools
    MSI (s) (D4:A0) [10:21:27:421]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\Start Menu\Programs\Startup
    MSI (s) (D4:A0) [10:21:27:423]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\Start Menu\Programs
    MSI (s) (D4:A0) [10:21:27:424]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\Start Menu
    MSI (s) (D4:A0) [10:21:27:426]: SHELL32::SHGetFolderPath returned: C:\Users\scomaction\Desktop
    MSI (s) (D4:A0) [10:21:27:427]: SHELL32::SHGetFolderPath returned: C:\ProgramData\Microsoft\Windows\Templates
    MSI (s) (D4:A0) [10:21:27:428]: SHELL32::SHGetFolderPath returned: C:\Windows\Fonts
    MSI (s) (D4:A0) [10:21:27:428]: Note: 1: 2898 2: MS Sans Serif 3: MS Sans Serif 4: 0 5: 16
    MSI (s) (D4:A0) [10:21:27:433]: MSI_LUA: Setting MsiRunningElevated property to 1 because the install is already running elevated.
    MSI (s) (D4:A0) [10:21:27:434]: PROPERTY CHANGE: Adding MsiRunningElevated property. Its value is '1'.
    MSI (s) (D4:A0) [10:21:27:434]: PROPERTY CHANGE: Adding Privileged property. Its value is '1'.
    MSI (s) (D4:A0) [10:21:27:434]: Note: 1: 1402 2: HKEY_CURRENT_USER\Software\Microsoft\MS Setup (ACME)\User Info 3: 2
    MSI (s) (D4:A0) [10:21:27:434]: PROPERTY CHANGE: Adding USERNAME property. Its value is 'Windows User'.
    MSI (s) (D4:A0) [10:21:27:434]: Note: 1: 1402 2: HKEY_CURRENT_USER\Software\Microsoft\MS Setup (ACME)\User Info 3: 2
    MSI (s) (D4:A0) [10:21:27:434]: PROPERTY CHANGE: Adding DATABASE property. Its value is 'C:\Windows\Installer\4b8344.msi'.
    MSI (s) (D4:A0) [10:21:27:434]: PROPERTY CHANGE: Adding OriginalDatabase property. Its value is 'F:\InstallFiles\SCOMR2\Setup\AMD64\Server\OMServer.msi'.
    MSI (s) (D4:A0) [10:21:27:434]: Machine policy value 'MsiDisableEmbeddedUI' is 0
    MSI (s) (D4:A0) [10:21:27:434]: EEUI - Disabling MsiEmbeddedUI due to existing external or embedded UI
    MSI (s) (D4:A0) [10:21:27:434]: EEUI - Disabling MsiEmbeddedUI for service because it's not a quiet/basic install
    MSI (s) (D4:A0) [10:21:27:434]: Note: 1: 2205 2: 3: PatchPackage
    MSI (s) (D4:A0) [10:21:27:434]: Machine policy value 'DisableRollback' is 0
    MSI (s) (D4:A0) [10:21:27:434]: User policy value 'DisableRollback' is 0
    MSI (s) (D4:A0) [10:21:27:434]: PROPERTY CHANGE: Adding UILevel property. Its value is '2'.
    === Logging started: 22/01/2014 10:21:27 ===
    MSI (s) (D4:A0) [10:21:27:435]: Note: 1: 2203 2: C:\Windows\Installer\inprogressinstallinfo.ipi 3: -2147287038
    MSI (s) (D4:A0) [10:21:27:436]: APPCOMPAT: [DetectVersionLaunchCondition] Launch condition already passes.
    MSI (s) (D4:A0) [10:21:27:438]: PROPERTY CHANGE: Adding ACTION property. Its value is 'INSTALL'.
    MSI (s) (D4:A0) [10:21:27:438]: Doing action: INSTALL
    Action start 10:21:27: INSTALL.
    MSI (s) (D4:A0) [10:21:27:444]: Running ExecuteSequence
    MSI (s) (D4:A0) [10:21:27:444]: Doing action: SystemFolder.A591E3B4_D228_431D_BF89_99D52C8FFB76
    MSI (s) (D4:A0) [10:21:27:447]: PROPERTY CHANGE: Adding SystemFolder.A591E3B4_D228_431D_BF89_99D52C8FFB76 property. Its value is 'C:\Windows\SysWOW64\'.
    Action start 10:21:27: SystemFolder.A591E3B4_D228_431D_BF89_99D52C8FFB76.
    MSI (s) (D4:A0) [10:21:27:448]: Doing action: System64Folder.A591E3B4_D228_431D_BF89_99D52C8FFB76
    Action ended 10:21:27: SystemFolder.A591E3B4_D228_431D_BF89_99D52C8FFB76. Return value 1.
    MSI (s) (D4:A0) [10:21:27:450]: PROPERTY CHANGE: Adding System64Folder.A591E3B4_D228_431D_BF89_99D52C8FFB76 property. Its value is 'C:\Windows\system32\'.
    Action start 10:21:27: System64Folder.A591E3B4_D228_431D_BF89_99D52C8FFB76.
    MSI (s) (D4:A0) [10:21:27:450]: Doing action: WindowsFolder.62894CB9_4320_40DB_B4E4_C0347FAB97B6
    Action ended 10:21:27: System64Folder.A591E3B4_D228_431D_BF89_99D52C8FFB76. Return value 1.
    MSI (s) (D4:A0) [10:21:27:452]: PROPERTY CHANGE: Adding WindowsFolder.62894CB9_4320_40DB_B4E4_C0347FAB97B6 property. Its value is 'C:\Windows\'.
    Action start 10:21:27: WindowsFolder.62894CB9_4320_40DB_B4E4_C0347FAB97B6.
    MSI (s) (D4:A0) [10:21:27:453]: Doing action: System64Folder.A7850EAF_DD6F_4ED6_9581_E958CBD8A522
    Action ended 10:21:27: WindowsFolder.62894CB9_4320_40DB_B4E4_C0347FAB97B6. Return value 1.
    MSI (s) (D4:A0) [10:21:27:455]: PROPERTY CHANGE: Adding System64Folder.A7850EAF_DD6F_4ED6_9581_E958CBD8A522 property. Its value is 'C:\Windows\system32\'.
    Action start 10:21:27: System64Folder.A7850EAF_DD6F_4ED6_9581_E958CBD8A522.
    MSI (s) (D4:A0) [10:21:27:456]: Doing action: WindowsFolder_x86_VC.DF495DFD_79F6_34DF_BB1E_E58DB5BDCF2C
    Action ended 10:21:27: System64Folder.A7850EAF_DD6F_4ED6_9581_E958CBD8A522. Return value 1.
    MSI (s) (D4:A0) [10:21:27:458]: PROPERTY CHANGE: Adding WindowsFolder_x86_VC.DF495DFD_79F6_34DF_BB1E_E58DB5BDCF2C property. Its value is 'C:\Windows\'.
    Action start 10:21:27: WindowsFolder_x86_VC.DF495DFD_79F6_34DF_BB1E_E58DB5BDCF2C.
    MSI (s) (D4:A0) [10:21:27:458]: Doing action: SystemFolder_x86_VC.DF495DFD_79F6_34DF_BB1E_E58DB5BDCF2C
    Action ended 10:21:27: WindowsFolder_x86_VC.DF495DFD_79F6_34DF_BB1E_E58DB5BDCF2C. Return value 1.
    MSI (s) (D4:A0) [10:21:27:461]: PROPERTY CHANGE: Adding SystemFolder_x86_VC.DF495DFD_79F6_34DF_BB1E_E58DB5BDCF2C property. Its value is 'C:\Windows\SysWOW64\'.
    Action start 10:21:27: SystemFolder_x86_VC.DF495DFD_79F6_34DF_BB1E_E58DB5BDCF2C.
    MSI (s) (D4:A0) [10:21:27:461]: Doing action: WindowsFolder_amd64_VC.1C11561A_11CB_36A7_8A47_D7A042055FA7
    Action ended 10:21:27: SystemFolder_x86_VC.DF495DFD_79F6_34DF_BB1E_E58DB5BDCF2C. Return value 1.
    MSI (s) (D4:A0) [10:21:27:463]: PROPERTY CHANGE: Adding WindowsFolder_amd64_VC.1C11561A_11CB_36A7_8A47_D7A042055FA7 property. Its value is 'C:\Windows\'.
    Action start 10:21:27: WindowsFolder_amd64_VC.1C11561A_11CB_36A7_8A47_D7A042055FA7.
    MSI (s) (D4:A0) [10:21:27:463]: Doing action: System64Folder_amd64_VC.1C11561A_11CB_36A7_8A47_D7A042055FA7
    Action ended 10:21:27: WindowsFolder_amd64_VC.1C11561A_11CB_36A7_8A47_D7A042055FA7. Return value 1.
    MSI (s) (D4:A0) [10:21:27:466]: PROPERTY CHANGE: Adding System64Folder_amd64_VC.1C11561A_11CB_36A7_8A47_D7A042055FA7 property. Its value is 'C:\Windows\system32\'.
    Action start 10:21:27: System64Folder_amd64_VC.1C11561A_11CB_36A7_8A47_D7A042055FA7.
    MSI (s) (D4:A0) [10:21:27:467]: Doing action: WindowsFolder.399B61E4_41A2_4BE4_889A_A0D0761C88A8
    Action ended 10:21:27: System64Folder_amd64_VC.1C11561A_11CB_36A7_8A47_D7A042055FA7. Return value 1.
    MSI (s) (D4:A0) [10:21:27:468]: PROPERTY CHANGE: Adding WindowsFolder.399B61E4_41A2_4BE4_889A_A0D0761C88A8 property. Its value is 'C:\Windows\'.
    Action start 10:21:27: WindowsFolder.399B61E4_41A2_4BE4_889A_A0D0761C88A8.
    MSI (s) (D4:A0) [10:21:27:469]: Doing action: WindowsFolder.80B659D9_F758_4E7D_B4FA_E53FC737DCC9
    Action ended 10:21:27: WindowsFolder.399B61E4_41A2_4BE4_889A_A0D0761C88A8. Return value 1.
    MSI (s) (D4:A0) [10:21:27:471]: PROPERTY CHANGE: Adding WindowsFolder.80B659D9_F758_4E7D_B4FA_E53FC737DCC9 property. Its value is 'C:\Windows\'.
    Action start 10:21:27: WindowsFolder.80B659D9_F758_4E7D_B4FA_E53FC737DCC9.
    MSI (s) (D4:A0) [10:21:27:472]: Doing action: WindowsFolder.3A3B255D_E19B_4D2E_8687_D6EF0314AFBE
    Action ended 10:21:27: WindowsFolder.80B659D9_F758_4E7D_B4FA_E53FC737DCC9. Return value 1.
    MSI (s) (D4:A0) [10:21:27:474]: PROPERTY CHANGE: Adding WindowsFolder.3A3B255D_E19B_4D2E_8687_D6EF0314AFBE property. Its value is 'C:\Windows\'.
    Action start 10:21:27: WindowsFolder.3A3B255D_E19B_4D2E_8687_D6EF0314AFBE.
    MSI (s) (D4:A0) [10:21:27:475]: Doing action: ProgramMenuFolder.CFE2C791_D05A_4240_90ED_DEB20161DFB0
    Action ended 10:21:27: WindowsFolder.3A3B255D_E19B_4D2E_8687_D6EF0314AFBE. Return value 1.
    MSI (s) (D4:A0) [10:21:27:477]: PROPERTY CHANGE: Adding ProgramMenuFolder.CFE2C791_D05A_4240_90ED_DEB20161DFB0 property. Its value is 'C:\ProgramData\Microsoft\Windows\Start Menu\Programs\'.
    Action start 10:21:27: ProgramMenuFolder.CFE2C791_D05A_4240_90ED_DEB20161DFB0.
    MSI (s) (D4:A0) [10:21:27:477]: Doing action: FindRelatedProducts
    Action ended 10:21:27: ProgramMenuFolder.CFE2C791_D05A_4240_90ED_DEB20161DFB0. Return value 1.
    Action start 10:21:27: FindRelatedProducts.
    MSI (s) (D4:A0) [10:21:27:481]: PROPERTY CHANGE: Adding CORECOMPONENTPRESENT_AGENT property. Its value is '{8B21425D-02F3-4B80-88CE-8F79B320D330}'.
    MSI (s) (D4:A0) [10:21:27:483]: Skipping action: _StopCoreServices.80B659D9_F758_4E7D_B4FA_E53FC737DCC9 (condition is false)
    MSI (s) (D4:A0) [10:21:27:483]: Skipping action: _KillOMProcesses.80B659D9_F758_4E7D_B4FA_E53FC737DCC9 (condition is false)
    MSI (s) (D4:A0) [10:21:27:483]: Skipping action: _SearchOpsMgrShellPath.CFE2C791_D05A_4240_90ED_DEB20161DFB0 (condition is false)
    MSI (s) (D4:A0) [10:21:27:483]: Doing action: _SetMonadFilePath.CFE2C791_D05A_4240_90ED_DEB20161DFB0
    Action ended 10:21:27: FindRelatedProducts. Return value 1.
    MSI (s) (D4:08) [10:21:27:501]: Invoking remote custom action. DLL: C:\Windows\Installer\MSI847C.tmp, Entrypoint: SetMonadFilePath
    MSI (s) (D4:B0) [10:21:27:502]: Generating random cookie.
    MSI (s) (D4:B0) [10:21:27:505]: Created Custom Action Server with PID 4964 (0x1364).
    MSI (s) (D4:34) [10:21:27:527]: Running as a service.
    MSI (s) (D4:34) [10:21:27:529]: Hello, I'm your 64bit Impersonated custom action server.
    Action start 10:21:27: _SetMonadFilePath.CFE2C791_D05A_4240_90ED_DEB20161DFB0.
    MSI (s) (D4!DC) [10:21:27:638]: PROPERTY CHANGE: Modifying MONAD_SHELL_PATH property. Its current value is 'Error: Value Never Set. Check the CACore:SetMonadFilePath CA'. Its new value: 'C:\Windows\System32\WindowsPowerShell\v1.0\powershell.exe'.
    GetRegistyStringValue: Registy key value found.. C:\Windows\System32\WindowsPowerShell\v1.0\powershell.exe
    MSI (s) (D4:A0) [10:21:27:640]: Doing action: _Set_CORECOMPONENTPRESENT
    Action ended 10:21:27: _SetMonadFilePath.CFE2C791_D05A_4240_90ED_DEB20161DFB0. Return value 1.
    MSI (s) (D4:A0) [10:21:27:643]: PROPERTY CHANGE: Adding CORECOMPONENTPRESENT property. Its value is '{8B21425D-02F3-4B80-88CE-8F79B320D330}'.
    Action start 10:21:27: _Set_CORECOMPONENTPRESENT.
    MSI (s) (D4:A0) [10:21:27:644]: Skipping action: _AbortDowngradeProductAttempt (condition is false)
    MSI (s) (D4:A0) [10:21:27:644]: Doing action: _AbortIncompatibleComponents
    Action ended 10:21:27: _Set_CORECOMPONENTPRESENT. Return value 1.
    Action start 10:21:27: _AbortIncompatibleComponents.
    MSI (s) (D4:30) [10:21:27:652]: I/O on thread 5044 could not be cancelled. Error: 1168
    MSI (s) (D4:30) [10:21:27:652]: I/O on thread 1580 could not be cancelled. Error: 1168
    MSI (s) (D4:30) [10:21:27:652]: I/O on thread 5512 could not be cancelled. Error: 1168
    MSI (s) (D4:30) [10:21:27:652]: I/O on thread 4268 could not be cancelled. Error: 1168
    MSI (s) (D4:30) [10:21:27:652]: I/O on thread 5024 could not be cancelled. Error: 1168
    MSI (s) (D4:30) [10:21:27:652]: I/O on thread 6064 could not be cancelled. Error: 1168
    MSI (s) (D4:30) [10:21:27:652]: I/O on thread 3396 could not be cancelled. Error: 1168
    MSI (s) (D4:30) [10:21:27:652]: I/O on thread 2704 could not be cancelled. Error: 1168
    MSI (s) (D4:30) [10:21:27:652]: I/O on thread 5568 could not be cancelled. Error: 1168
    MSI (s) (D4:30) [10:21:27:652]: I/O on thread 5940 could not be cancelled. Error: 1168
    MSI (s) (D4:30) [10:21:27:652]: I/O on thread 1968 could not be cancelled. Error: 1168
    MSI (s) (D4:A0) [10:21:27:652]: Product: System Center Operations Manager 2012 Server -- The Operations Manager management server cannot be installed on a computer on which the Operations Manager agent, Operations Manager gateway, System Center Essentials, or System Center Service Manager is already installed. These must be uninstalled to proceed.
    The Operations Manager management server cannot be installed on a computer on which the Operations Manager agent, Operations Manager gateway, System Center Essentials, or System Center Service Manager is already installed. These must be uninstalled to proceed.
    Action ended 10:21:27: _AbortIncompatibleComponents. Return value 3.
    Action ended 10:21:27: INSTALL. Return value 3.
    Property(S): DiskPrompt = Please Insert Disk 1
    Property(S): UpgradeCode = {17058653-A628-4C03-8F80-5E2B179ECD55}
    Property(S): SCDATABASENAME = OperationsManager
    Property(S): SC_DB_SERVER = SCOM-XXX-AG
    Property(S): SDK_PASSWORD.540EA3C0_A5E9_41EA_A585_822C09EA2650 = **********
    Property(S): CORECOMPONENTPRESENT = {8B21425D-02F3-4B80-88CE-8F79B320D330}
    Property(S): OM_INSTALLDIR = F:\Program Files\Microsoft System Center 2012 R2\Operations Manager
    Property(S): ProgramFiles64Folder = C:\Program Files\
    Property(S): Privileged = 1
    Property(S): ARPSYSTEMCOMPONENT = 1
    Property(S): DONOTSKIPDELETESERVICES = 0
    Property(S): DONOTSKIPINSTALLSERVICES = 0
    Property(S): OM_COMMON_PRODUCT_REGISTRY_PATH = SOFTWARE\Microsoft\System Center Operations Manager
    Property(S): OM_COMMON_PRODUCT_RELEASE_REGISTRY_KEY = 12
    Property(S): OM_COMMON_PRODUCT_DEFAULT_INSTALL_DIR = System Center Operations Manager
    Property(S): NetFxVersion = v2.0.50727
    Property(S): IS_OM_SERVER = 1
    Property(S): InstallAPMAgent = 1
    Property(S): INSTALLLEVEL = 100
    Property(S): ALLUSERS = 1
    Property(S): ARPNOREPAIR = 0
    Property(S): ARPURLINFOABOUT = http://www.microsoft.com/mom
    Property(S): ARPURLUPDATEINFO = http://www.microsoft.com/mom
    Property(S): ARPHELPLINK = http://support.microsoft.com
    Property(S): MSIRESTARTMANAGERCONTROL = Disable
    Property(S): SQL_PORT = 1433
    Property(S): DbSizeGood = 1
    Property(S): DbFileOptionsGood = 1
    Property(S): DbFilesSpaceGood = 1
    Property(S): DbNameGood = 1
    Property(S): SqlServicesStarted = 1
    Property(S): _SetSDKServiceAccount.540EA3C0_A5E9_41EA_A585_822C09EA2650 = **********
    Property(S): _SetConfigServiceAccount.540EA3C0_A5E9_41EA_A585_822C09EA2650 = **********
    Property(S): DialogWizardTitle = System Center 2012 R2 Operations Manager Setup
    Property(S): MinimumOSMsg = This product must be installed on Windows Server 2008 R2 or higher.
    Property(S): MOMSDKPortDesc = Operations Manager SDK.
    Property(S): MOMConnectorPortDesc = Operations Manager Connector Framework.
    Property(S): MOMAEMPortDesc = Operations Manager Application Error Monitoring.
    Property(S): MOMSQMPortDesc = Operations Manager Customer Experience Improvement Program.
    Property(S): MOMHSPortDesc = System Center Management Health Service
    Property(S): SCOMV3SP1ProgramName = System Center 2012 R2 Operations Manager
    Property(S): FWRulePingRequestName = Operations Manager Ping Request (Echo Request - ICMPv4 OUT)
    Property(S): FWRulePingRequestDesc = Operations Manager network monitoring ping request
    Property(S): FWRulePingResponseName = Operations Manager Ping Response (Echo Response - ICMPv4 IN)
    Property(S): FWRulePingResponseDesc = Operations Manager network monitoring ping response
    Property(S): FWRuleSnmpRequestName = Operations Manager SNMP Request
    Property(S): FWRuleSnmpRequestDesc = Operations Manager network monitoring SNMP request
    Property(S): FWRuleSnmpResponseName = Operations Manager SNMP Response
    Property(S): FWRuleSnmpResponseDesc = Operations Manager network monitoring SNMP response
    Property(S): FWRuleSnmpTrapListenerName = Operations Manager SNMP Trap Listener
    Property(S): FWRuleSnmpTrapListenerDesc = Operations Manager network monitoring SNMP trap listener
    Property(S): Manufacturer = Microsoft Corporation
    Property(S): ProductCode = {C92727BE-BD12-4140-96A6-276BA4F60AC1}
    Property(S): ProductLanguage = 1033
    Property(S): ProductName = System Center Operations Manager 2012 Server
    Property(S): ProductVersion = 7.1.10226.0
    Property(S): SecureCustomProperties = ACTIONSPASSWORD;CORECOMPONENTPRESENT_AGENT;CORECOMPONENTPRESENT_GW;CORECOMPONENTPRESENT_RC;CORECOMPONENTPRESENT_SCE;CORECOMPONENTPRESENT_SMB2;CORECOMPONENTPRESENT_SMRTM;IS_AVICODE_AGENT_INSTALLED;IS_MOMASPAGENT_INSTALLED;MOM_DB_SERVER;MOMDATABASENAME_OLD;OM_NEWER_PRODUCT_FOUND;SDK_PASSWORD.540EA3C0_A5E9_41EA_A585_822C09EA2650;SQL_PORT
    Property(S): MsiHiddenProperties = _SetConfigServiceAccount.540EA3C0_A5E9_41EA_A585_822C09EA2650;_SetSDKServiceAccount.540EA3C0_A5E9_41EA_A585_822C09EA2650;ACTIONSPASSWORD;SDK_PASSWORD.540EA3C0_A5E9_41EA_A585_822C09EA2650
    Property(S): WixPdbPath = d:\btvsts\20867\private\product\setup\wix\msi\server\om\obj\amd64\OMServer.wixpdb
    Property(S): CORECOMPONENTPRESENT_AGENT = {8B21425D-02F3-4B80-88CE-8F79B320D330}
    Property(S): ProgramMenuFolder.CFE2C791_D05A_4240_90ED_DEB20161DFB0 = C:\ProgramData\Microsoft\Windows\Start Menu\Programs\
    Property(S): MONAD_SHELL_PATH = C:\Windows\System32\WindowsPowerShell\v1.0\powershell.exe
    Property(S): EnableEV.CFE2C791_D05A_4240_90ED_DEB20161DFB0 = 1
    Property(S): AddInstallPath.CFE2C791_D05A_4240_90ED_DEB20161DFB0 = add
    Property(S): RemoveInstallPath.CFE2C791_D05A_4240_90ED_DEB20161DFB0 = remove
    Property(S): WindowsFolder.3A3B255D_E19B_4D2E_8687_D6EF0314AFBE = C:\Windows\
    Property(S): VersionNT = 602
    Property(S): DW_DB_SERVER = SCOM-XXX-AG
    Property(S): DWDATABASENAME = OperationsManagerDW
    Property(S): OMDATABASENAME = OperationsManger
    Property(S): MaximumDataAgeMinutes = 10080
    Property(S): MaximumQueueSizeKB = 102400
    Property(S): MOMSDKPort.1451A536_2C9B_42F2_A37A_C9C6460E7EEA = 5724
    Property(S): MOMConnectorPort.1451A536_2C9B_42F2_A37A_C9C6460E7EEA = 51905
    Property(S): MOMAEMPort.1451A536_2C9B_42F2_A37A_C9C6460E7EEA = 51906
    Property(S): MOMSQMPort.1451A536_2C9B_42F2_A37A_C9C6460E7EEA = 51907
    Property(S): SDK_SERVICE_TYPE = 4
    Property(S): ROOT_MANAGEMENT_SERVER_PORT = 5723
    Property(S): SERVER_MANAGEMENT_GROUP_TYPE.C6F00077_9737_419B_A8B6_B309BA6F8FC8 = 1
    Property(S): MaximumForwardedVirtualQueuePercentage = 8
    Property(S): QueueSendDataSinglePriority = 0
    Property(S): ADMIN_ROLE_GROUP.C6F00077_9737_419B_A8B6_B309BA6F8FC8 = Administrators
    Property(S): USE_MANUALLY_SPECIFIED_SETTINGS = 1
    Property(S): WindowsFolder.80B659D9_F758_4E7D_B4FA_E53FC737DCC9 = C:\Windows\
    Property(S): CommonFiles64Folder = C:\Program Files\Common Files\
    Property(S): CAN_REGISTER_FOR_MU = 0
    Property(S): MU_SETTING = 0
    Property(S): IS_ROOT_HEALTH_SERVICE = 0
    Property(S): IS_MOM_SERVER = 0
    Property(S): IS_MOM_GATEWAY = 0
    Property(S): WindowsFolder.399B61E4_41A2_4BE4_889A_A0D0761C88A8 = C:\Windows\
    Property(S): WindowsFolder_amd64_VC.1C11561A_11CB_36A7_8A47_D7A042055FA7 = C:\Windows\
    Property(S): System64Folder_amd64_VC.1C11561A_11CB_36A7_8A47_D7A042055FA7 = C:\Windows\system32\
    Property(S): DirectoryTable100_amd64.1C11561A_11CB_36A7_8A47_D7A042055FA7 = DirectoryTable
    Property(S): WindowsFolder_x86_VC.DF495DFD_79F6_34DF_BB1E_E58DB5BDCF2C = C:\Windows\
    Property(S): SystemFolder_x86_VC.DF495DFD_79F6_34DF_BB1E_E58DB5BDCF2C = C:\Windows\SysWOW64\
    Property(S): DirectoryTable100_x86.DF495DFD_79F6_34DF_BB1E_E58DB5BDCF2C = DirectoryTable
    Property(S): SEND_CEIP_REPORTS = 0
    Property(S): System64Folder.A7850EAF_DD6F_4ED6_9581_E958CBD8A522 = C:\Windows\system32\
    Property(S): ACS_AGENT_ACCOUNT.A7850EAF_DD6F_4ED6_9581_E958CBD8A522 =
    Property(S): WindowsFolder.62894CB9_4320_40DB_B4E4_C0347FAB97B6 = C:\Windows\
    Property(S): SC_COMMON_REGISTRY_PATH = SOFTWARE\Microsoft\System Center\2010\Common
    Property(S): DISCOVERY_DATA_AUTHORIZATION_ENABLED = 0
    Property(S): IcmpProtocol.ADADB3CF_4DA7_4040_90AE_3E4E0E0A6FBF = 1
    Property(S): IcmpRequestType.ADADB3CF_4DA7_4040_90AE_3E4E0E0A6FBF = 8:*
    Property(S): IcmpResponseType.ADADB3CF_4DA7_4040_90AE_3E4E0E0A6FBF = 0:*
    Property(S): SnmpProtocol.ADADB3CF_4DA7_4040_90AE_3E4E0E0A6FBF = 17
    Property(S): SnmpPort.ADADB3CF_4DA7_4040_90AE_3E4E0E0A6FBF = 161
    Property(S): SnmpTrapPort.ADADB3CF_4DA7_4040_90AE_3E4E0E0A6FBF = 162
    Property(S): DirectionIn.ADADB3CF_4DA7_4040_90AE_3E4E0E0A6FBF = 0
    Property(S): DirectionOut.ADADB3CF_4DA7_4040_90AE_3E4E0E0A6FBF = 1
    Property(S): SystemFolder.A591E3B4_D228_431D_BF89_99D52C8FFB76 = C:\Windows\SysWOW64\
    Property(S): System64Folder.A591E3B4_D228_431D_BF89_99D52C8FFB76 = C:\Windows\system32\
    Property(S): ADVISOR_UPLOADFREQUENCY_PROP.192DDC2A_1CC5_4B2A_9D76_D8D0FC70175A = #1
    Property(S): ADVISOR_UPLOADDAY_PROP.192DDC2A_1CC5_4B2A_9D76_D8D0FC70175A = #-1
    Property(S): ADVISOR_UPLOADTIMEHOUR_PROP.192DDC2A_1CC5_4B2A_9D76_D8D0FC70175A = #-1
    Property(S): ADVISOR_UPLOADTIMEMIN_PROP.192DDC2A_1CC5_4B2A_9D76_D8D0FC70175A = #-1
    Property(S): ADVISOR_MAXCACHESIZE_PROP.192DDC2A_1CC5_4B2A_9D76_D8D0FC70175A = #1024
    Property(S): ADVISOR_MAXMAILBOXSIZE_PROP.192DDC2A_1CC5_4B2A_9D76_D8D0FC70175A = #1024
    Property(S): ADVISOR_ARCHIVEPERIOD_PROP.192DDC2A_1CC5_4B2A_9D76_D8D0FC70175A = #5
    Property(S): ADVISOR_LOGLEVEL_PROP.192DDC2A_1CC5_4B2A_9D76_D8D0FC70175A = #3
    Property(S): ADVISOR_NEEDMPINITIALIZE_PROP.192DDC2A_1CC5_4B2A_9D76_D8D0FC70175A = #1
    Property(S): ADVISOR_LYNC_PROP.192DDC2A_1CC5_4B2A_9D76_D8D0FC70175A = #0
    Property(S): ADVISOR_SHAREPOINT_PROP.192DDC2A_1CC5_4B2A_9D76_D8D0FC70175A = #0
    Property(S): MsiLogFileLocation = C:\Users\scomaction\AppData\Local\SCOM\Logs\OMServer.log
    Property(S): PackageCode = {58EFE971-58C1-4DBD-A400-A7607A745475}
    Property(S): ProductState = -1
    Property(S): PackagecodeChanging = 1
    Property(S): REBOOT = ReallySuppress
    Property(S): CURRENTDIRECTORY = C:\Users\scomaction\AppData\Local\SCOM\Setup
    Property(S): CLIENTUILEVEL = 3
    Property(S): MSICLIENTUSESEXTERNALUI = 1
    Property(S): CLIENTPROCESSID = 4472
    Property(S): MsiSystemRebootPending = 1
    Property(S): VersionDatabase = 300
    Property(S): VersionMsi = 5.00
    Property(S): VersionNT64 = 602
    Property(S): WindowsBuild = 9200
    Property(S): ServicePackLevel = 0
    Property(S): ServicePackLevelMinor = 0
    Property(S): MsiNTProductType = 3
    Property(S): WindowsFolder = C:\Windows\
    Property(S): WindowsVolume = C:\
    Property(S): System64Folder = C:\Windows\system32\
    Property(S): SystemFolder = C:\Windows\SysWOW64\
    Property(S): RemoteAdminTS = 1
    Property(S): TempFolder = C:\Users\SCOMAC~1\AppData\Local\Temp\
    Property(S): ProgramFilesFolder = C:\Program Files (x86)\
    Property(S): CommonFilesFolder = C:\Program Files (x86)\Common Files\
    Property(S): AppDataFolder = C:\Users\scomaction\AppData\Roaming\
    Property(S): FavoritesFolder = C:\Users\scomaction\Favorites\
    Property(S): NetHoodFolder = C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\Network Shortcuts\
    Property(S): PersonalFolder = C:\Users\scomaction\Documents\
    Property(S): PrintHoodFolder = C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\Printer Shortcuts\
    Property(S): RecentFolder = C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\Recent\
    Property(S): SendToFolder = C:\Users\scomaction\AppData\Roaming\Microsoft\Windows\SendTo\
    Property(S): TemplateFolder = C:\ProgramData\Microsoft\Windows\Templates\
    Property(S): CommonAppDataFolder = C:\ProgramData\
    Property(S): LocalAppDataFolder = C:\Users\scomaction\AppData\Local\
    Property(S): MyPicturesFolder = C:\Users\scomaction\Pictures\
    Property(S): AdminToolsFolder = C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Administrative Tools\
    Property(S): StartupFolder = C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Startup\
    Property(S): ProgramMenuFolder = C:\ProgramData\Microsoft\Windows\Start Menu\Programs\
    Property(S): StartMenuFolder = C:\ProgramData\Microsoft\Windows\Start Menu\
    Property(S): DesktopFolder = C:\Users\Public\Desktop\
    Property(S): FontsFolder = C:\Windows\Fonts\
    Property(S): GPTSupport = 1
    Property(S): OLEAdvtSupport = 1
    Property(S): ShellAdvtSupport = 1
    Property(S): MsiAMD64 = 6
    Property(S): Msix64 = 6
    Property(S): Intel = 6
    Property(S): PhysicalMemory = 8192
    Property(S): VirtualMemory = 7854
    Property(S): AdminUser = 1
    Property(S): MsiTrueAdminUser = 1
    Property(S): LogonUser = scomaction
    Property(S): UserSID = S-1-5-21-607126847-70518424-489426498-210484
    Property(S): UserLanguageID = 2057
    Property(S): ComputerName = SCOMMS1-VM
    Property(S): SystemLanguageID = 2057
    Property(S): ScreenX = 1024
    Property(S): ScreenY = 768
    Property(S): CaptionHeight = 23
    Property(S): BorderTop = 1
    Property(S): BorderSide = 1
    Property(S): TextHeight = 16
    Property(S): TextInternalLeading = 3
    Property(S): ColorBits = 32
    Property(S): TTCSupport = 1
    Property(S): Time = 10:21:27
    Property(S): Date = 22/01/2014
    Property(S): MsiNetAssemblySupport = 4.0.30319.17929
    Property(S): MsiWin32AssemblySupport = 6.2.9200.16384
    Property(S): RedirectedDllSupport = 2
    Property(S): MsiRunningElevated = 1
    Property(S): USERNAME = Windows User
    Property(S): DATABASE = C:\Windows\Installer\4b8344.msi
    Property(S): OriginalDatabase = F:\InstallFiles\SCOMR2\Setup\AMD64\Server\OMServer.msi
    Property(S): UILevel = 2
    Property(S): ACTION = INSTALL
    MSI (s) (D4:A0) [10:21:27:697]: Note: 1: 1708
    MSI (s) (D4:A0) [10:21:27:698]: Product: System Center Operations Manager 2012 Server -- Installation operation failed.
    MSI (s) (D4:A0) [10:21:27:698]: Windows Installer installed the product. Product Name: System Center Operations Manager 2012 Server. Product Version: 7.1.10226.0. Product Language: 1033. Manufacturer: Microsoft Corporation. Installation success or error status: 1603.
    MSI (s) (D4:A0) [10:21:27:744]: Deferring clean up of packages/files, if any exist
    MSI (s) (D4:A0) [10:21:27:744]: MainEngineThread is returning 1603
    MSI (s) (D4:30) [10:21:27:744]: No System Restore sequence number for this installation.
    === Logging stopped: 22/01/2014 10:21:27 ===
    MSI (s) (D4:30) [10:21:27:746]: User policy value 'DisableRollback' is 0
    MSI (s) (D4:30) [10:21:27:746]: Machine policy value 'DisableRollback' is 0
    MSI (s) (D4:30) [10:21:27:746]: Incrementing counter to disable shutdown. Counter after increment: 0
    MSI (s) (D4:30) [10:21:27:746]: Note: 1: 1402 2: HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Installer\Rollback\Scripts 3: 2
    MSI (s) (D4:30) [10:21:27:746]: Note: 1: 1402 2: HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Installer\Rollback\Scripts 3: 2
    MSI (s) (D4:30) [10:21:27:746]: Decrementing counter to disable shutdown. If counter >= 0, shutdown will be denied. Counter after decrement: -1
    MSI (s) (D4:30) [10:21:27:747]: Destroying RemoteAPI object.
    MSI (s) (D4:B0) [10:21:27:747]: Custom Action Manager thread ending.
    MSI (c) (78:34) [10:21:27:748]: Decrementing counter to disable shutdown. If counter >= 0, shutdown will be denied. Counter after decrement: -1
    MSI (c) (78:34) [10:21:27:749]: MainEngineThread is returning 1603
    === Verbose logging stopped: 22/01/2014 10:21:27 ===
    Any assistance anyone can provide will be greatly appreciated.

    Verify from permission of user that you use it in upgrade, make sure that scom machine and user that you use it in upgrade in sysadmin group in database of operationsManager and OperationsManagerDW
    Also Verify from Prerequisites of Upgrade SCOM 2012 sp1 as below link
    http://technet.microsoft.com/en-us/library/jj656654.aspx
    Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"

  • How to install Small Business Server 2008 in an existing Active Directory domain

    It is shown on this page:
    http://support.microsoft.com/kb/884453, "How to install Small Business Server 2003 in an existing Active Directory domain".
    Is it possible to do this with SBS2008 ?
    If "YES", are there any published information about the procedure ?

    Yes, it is. Thank you very much.
    But there is something that confuses me - I want to migrate from Win2003Std to SBS2008. And also, I want to keep the existing Win2003Std as a second DC for a long time.
    But it is written in the shown article:
    ... After the migration is finished, you must remove the Source Server from the network within 21 days. ...
    Is this rule mandatory for the scenarios where the Source Server is Std, not SBS ? As I know, I can have more than one DC(Win2003Std/Win2008Std) together with SBS2003. But what about SBS2008 ?

Maybe you are looking for

  • Bar code3 in alv

    hi, i need to display barcode in alv report  how to do this, pls provide sample code. regards, jai

  • Its is possible to back up the songs that i have on my iPod touch in iCloud or either in iTunes?

    its is possible to back up the songs that i have on my iPod touch in iCloud or either in iTunes?

  • How to refer to other objects?

    Greetings, I'm not sure how objects should refer to other objects. Example: Class Automobile needs to refer to objects from other classes, namely to tires, color, motor and company. So, the way I would do this in C++ or VB is to store all tire, color

  • FlowChart Applet.. where to begin?

    Hello =) could any of you help me please I have to make an Applet to build FlowCharts.. this applet eventually has to integrate with MySQL database to save and fetch data to rebuild the FlowChart for now I've used some buttons and icons to make the f

  • FXML: Sizes relative to screen size

    Hi, I am currently trying to set up a PerspektiveTransform which is somehow relative to the Stages size. Is there any way of accessing the stages, size or will i have to inject this via the FXMLLoader? greetings, andreas