Forcedeth on MPC55 "no link during initialization" no net cable detect

Hello-
I have recently started having a problem with my computer. I cannot get the network card to detect the cable. The cable worked before with this computer, and still works with other computers.
The problem started 30 Nov 2013.
There were recent upgrades of networkmanager as well as util-linux, linux-firmware, linux-api-headers, mkinitcpio, and linux (3.9.8-1 to 3.12-1), but looking through the logs there were working reboots after all of these upgrades.
The network device shows in lspci
the kernel driver is loaded
dmesg shows the driver loading as well as networkmanager seeing the interface
kernel reports 'no link during initialization' and 'link is not ready'
modprobe -r and re-modprobe forcedeth leads to same messages and does not fix the problem
ip link shows
lenp0s8: <NO_CARRIER,BROADCAST,MULTICAST,UP> .. ... state DOWN
Any ideas of where else to start looking?

I just booted from an older arch boot usb drive, and it had the same results.
I'm wondering if the hardware is bad.
The version i'm booting from has a kernel of 3.6.4-1-arch
The strange thing is that the last time the network card was working, it was working until it was taken down during a power-off.
Is there something i can check with ethtool or another tool?
A cursory glance shows
Speed: Unknown!
Duplex: Unknown! (255)
Link detected:no
Everything else looks normal

Similar Messages

Eth0 won't come up anymore - eth0: no link during initialization

Arch i686 has been running fine for months on my old Athlon nForce2 board. Today, I booted and found that eth0 can't come up. If I look at my router, there isn't a link light on for that box/same is true on the back of the box. I know that the cable is good (tested it with my laptop). I also replaced the NIC in the box with one that I know works in another box and I get the same story. Finally, I booted with a live Ubuntu CD and got the same problem where it couldn't use the network.
I have tried both dhcp and static modes with no change in the behavior.
When I restart the network (/etc/rc.d/network restart) I get the following two lines In /var/log/dmesg I get:
eth0: no link during initialization.
ADDRCONF(NETDEV_UP): eth0: link is not ready
Link to full /var/log/dmesg is here
$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:0C:6E:60:D4:54
inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:22 Base address:0x4000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:47 errors:0 dropped:0 overruns:0 frame:0
TX packets:47 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3902 (3.8 Kb) TX bytes:3902 (3.8 Kb)
$ cat /etc/rc.conf
LOCALE="en_US.utf8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="US/Eastern"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(!snd_pcsp !pcspkr asb100 lirc_streamzap lirc_dev)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
HOSTNAME="lightning"
# Static IP
#eth0="eth0 192.168.0.5 netmask 255.255.255.0 broadcast 192.168.0.255"
#INTERFACES=(eth0)
#gateway="default gw 192.168.0.1"
#ROUTES=(gateway)
# DHCP
eth0="dhcp"
INTERFACES=(eth0)
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
DAEMONS=(syslog-ng network netfs lircd @crond @sshd @alsa @openntpd @athcool @hal @lighttpd sensors @monitorix @samba slim)
# ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised auto-negotiation: Yes
Speed: Unknown! (65535)
Duplex: Unknown! (255)
Port: MII
PHYAD: 1
Transceiver: external
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Link detected: no

Can't explain it... the Mac laptop works just fine but the Arch box doesn't work at all. The only way it works is to hit the uplink button on the back of the router. Crazy.

Link is down. No cable detected

I have the Linksys Wireless-G Broadband Router with SRX200 (WRT54GX2) and can connect to the internet [and to the router] using a wireless connection. However, when I can connect an ethernet cable to the router it is not detected. I get the following message "Link is down. No cable detected"

You should check if your card is enabled, try to use other cables also, try other computers on the same port and see if you at least have a light lit on it.. isolation is the key, coz you need to know where the problem is, it can either be the ethernet card, the cable or the port on the router that is derfective.. ayt?!
"Sometimes your knight in shining armor is just a retard in tin foil.."-ARCHANGEL_06

Error ocurred during initialization of VM. Unable to load native library...

Hi,
I´m trying to install Oracle 9i on a PC with Suse 9.2.
when I put the first CD it comes with this error:
Initializing Java Virtual Machine from /tmp/OraInstall2006-05-04_11-13-11PM/jre/bin/java. Please wait...
Error occurred during initialization of VM
Unable to load native library: /tmp/OraInstall2006-05-04_11-13-11PM/jre/lib/i386/libjava.so: symbol __libc_wait, version GLIBC_2.0 not defined in file libc.so.6 with link time reference
I´ve seen that there was a similar issue in 2004 and I´ve trying to do what it says but it didn´t work this time.
Unable to load native library:
Could everyone help me to install Oracle??? I´ve been trying it for a few days and doesn´t work.
Regards,

I had same problems long time ago. Ok, I try to remember.
First I read the recommandation. You need a special GLIBC-Library to support the JAVA 1.1.8 runtime environment.
Some of the Oracle9i tools are compiled with gcc 2.95 compiler.
You may need gcc_old for SLES9 for linking of those tools.
gcc_old-2.95.3-175.2.i586.rpm is included in SLES 9 SP2 CD1
For Suse you can obtain a package called orarun. You will get further support for installing, starting and stopping ORACLE. Please look at http://ftp.novell.com/partners/oracle/docs/9205_sles9_install.pdf.
Good luck.

000364 Server failed during initialization

I've installed the WLS 7 on a Sun Solaris machine. I was able to install
and startup the server. However, after shuting down the server and
attempting another startup the following exception is encounted. Any ideas
what might be causing this?:
Starting WebLogic Server...
<Feb 11, 2003 2:54:59 PM PST> <Critical> <WebLogicServer> <000364> <Server
failed during initialization.
Exception:weblogic.management.configuration.ConfigurationException: - with
nested exception:
[java.lang.NullPointerException]
java.lang.NullPointerException
at weblogic.management.commo.Commo.initInstances(Commo.java:207)
at weblogic.management.commo.Commo.init(Commo.java:125)
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
77)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
--------------- nested within: ------------------
weblogic.management.configuration.ConfigurationException: - with nested
exception:
[java.lang.NullPointerException]
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
86)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
>
The WebLogic Server did not start up properly.
Exception raised:
java.lang.NullPointerException
at weblogic.management.commo.Commo.initInstances(Commo.java:207)
at weblogic.management.commo.Commo.init(Commo.java:125)
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
77)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
--------------- nested within: ------------------
weblogic.management.configuration.ConfigurationException: - with nested
exception:
[java.lang.NullPointerException]
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
86)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
Reason: Fatal initialization exception
Throwable: weblogic.management.configuration.ConfigurationException: - with
nested exception:
[java.lang.NullPointerException]
java.lang.NullPointerException
at weblogic.management.commo.Commo.initInstances(Commo.java:207)
at weblogic.management.commo.Commo.init(Commo.java:125)
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
77)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
--------------- nested within: ------------------
weblogic.management.configuration.ConfigurationException: - with nested
exception:
[java.lang.NullPointerException]
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
86)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
Thanks,
John

I have similar problem with WebLogic sp2 on Solaris 8. I get the following message
when I try to start admin server:
<Critical> <WebLogicServer> <000364> <Server failed during initialization. Exception:weblogic.management.configuration.ConfigurationException:
- with nested exception:
[java.lang.NullPointerException]
java.lang.NullPointerException
at weblogic.management.commo.Commo.initInstances(Commo.java:207)
at weblogic.management.commo.Commo.init(Commo.java:125)
at weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:477)
at weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:664)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:594)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:282)
at weblogic.Server.main(Server.java:32)
--------------- nested within: ------------------
weblogic.management.configuration.ConfigurationException: - with nested exception:
[java.lang.NullPointerException]
at weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:486)
at weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:664)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:594)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:282)
at weblogic.Server.main(Server.java:32)
>
The WebLogic Server did not start up properly.
Exception raised:
java.lang.NullPointerException
at weblogic.management.commo.Commo.initInstances(Commo.java:207)
at weblogic.management.commo.Commo.init(Commo.java:125)
at weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:477)
at weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:664)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:594)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:282)
at weblogic.Server.main(Server.java:32)
--------------- nested within: ------------------
weblogic.management.configuration.ConfigurationException: - with nested exception:
[java.lang.NullPointerException]
at weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:486)
at weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:664)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:594)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:282)
at weblogic.Server.main(Server.java:32)
Reason: Fatal initialization exception
Throwable: weblogic.management.configuration.ConfigurationException: - with nested
exception:
[java.lang.NullPointerException]
java.lang.NullPointerException
at weblogic.management.commo.Commo.initInstances(Commo.java:207)
at weblogic.management.commo.Commo.init(Commo.java:125)
at weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:477)
at weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:664)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:594)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:282)
at weblogic.Server.main(Server.java:32)
--------------- nested within: ------------------
weblogic.management.configuration.ConfigurationException: - with nested exception:
[java.lang.NullPointerException]
at weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:486)
at weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:664)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:594)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:282)
at weblogic.Server.main(Server.java:32)
+ set +x
Please help
"Ashish" <[email protected]> wrote:
>
>
>
Hi Scott,
I am facing same problem (same error log as described below). I
have installed
WEblogic 7.0 SP2 on Windows XP. will apprceaite any help on this.
Thanks & Regards,
Ashish
"Wayne W. Scott" <[email protected]> wrote:
This looks very much like a case I worked last week. A problem report
had ~10 cases
linked to it. A patch is available for WLS 7.0 SP1; it's automatically
in SP2. So,
please tell me more about your environments and then I can tell if it's
applicable.
Thanks,
Wayne Scott
ben wrote:
hi, i am also having the server initialization problem, i am a novice
to this....could someone please help us out...
thanx in advance.
ben
"John Doody" <[email protected]> wrote in message news:<[email protected]>...
I've installed the WLS 7 on a Sun Solaris machine. I was able to
install
and startup the server. However, after shuting down the server and
attempting another startup the following exception is encounted. Anyideas
what might be causing this?:
Starting WebLogic Server...
<Feb 11, 2003 2:54:59 PM PST> <Critical> <WebLogicServer> <000364><Server
failed during initialization.
Exception:weblogic.management.configuration.ConfigurationException:- with
nested exception:
[java.lang.NullPointerException]
java.lang.NullPointerException
at weblogic.management.commo.Commo.initInstances(Commo.java:207)
at weblogic.management.commo.Commo.init(Commo.java:125)
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
77)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
--------------- nested within: ------------------
weblogic.management.configuration.ConfigurationException: - with
nested
exception:
[java.lang.NullPointerException]
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
86)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
The WebLogic Server did not start up properly.
Exception raised:
java.lang.NullPointerException
at weblogic.management.commo.Commo.initInstances(Commo.java:207)
at weblogic.management.commo.Commo.init(Commo.java:125)
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
77)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
--------------- nested within: ------------------
weblogic.management.configuration.ConfigurationException: - withnested
exception:
[java.lang.NullPointerException]
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
86)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
Reason: Fatal initialization exception
Throwable: weblogic.management.configuration.ConfigurationException:- with
nested exception:
[java.lang.NullPointerException]
java.lang.NullPointerException
at weblogic.management.commo.Commo.initInstances(Commo.java:207)
at weblogic.management.commo.Commo.init(Commo.java:125)
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
77)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
--------------- nested within: ------------------
weblogic.management.configuration.ConfigurationException: - with
nested
exception:
[java.lang.NullPointerException]
at
weblogic.management.AdminServerAdmin.initializeCommo(AdminServerAdmin.java:4
86)
at
weblogic.management.AdminServerAdmin.initialize(AdminServerAdmin.java:108)
at weblogic.t3.srvr.T3Srvr.initialize1(T3Srvr.java:659)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:589)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:277)
at weblogic.Server.main(Server.java:32)
Thanks,
John

Error occurred during initialization of VM

im new to jdeveloper please anyone help me...
Starting WLS with line:
C:\Oracle\MIDDLE~1\JDK160~1\bin\java -client -Xms256m -Xmx512m -XX:CompileThreshold=8000 -XX:PermSize=128m -XX:MaxPermSize=512m -Dweblogic.Name=DefaultServer -Djava.security.policy=C:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic.policy -Djavax.net.ssl.trustStore=C:\Users\reir\AppData\Local\Temp\trustStore9189074039610736238.jks -javaagent:../modules/org.eclipse.persistence_1.1.0.0_2-1.jar -Doracle.jdeveloper.adrs=true -Dweblogic.nodemanager.ServiceEnabled=true -Xverify:none -da -Dplatform.home=C:\Oracle\MIDDLE~1\WLSERV~1.3 -Dwls.home=C:\Oracle\MIDDLE~1\WLSERV~1.3\server -Dweblogic.home=C:\Oracle\MIDDLE~1\WLSERV~1.3\server -Djps.app.credential.overwrite.allowed=true -Dcommon.components.home=C:\Oracle\MIDDLE~1\ORACLE~1 -Djrf.version=11.1.1 -Dorg.apache.commons.logging.Log=org.apache.commons.logging.impl.Jdk14Logger -Ddomain.home=C:\Users\reir\AppData\Roaming\JDEVEL~1\SYSTEM~1.81\DEFAUL~1 -Djrockit.optfile=C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jrf_11.1.1\jrocket_optfile.txt -Doracle.server.config.dir=C:\Users\reir\AppData\Roaming\JDEVEL~1\SYSTEM~1.81\DEFAUL~1\config\FMWCON~1\servers\DefaultServer -Doracle.domain.config.dir=C:\Users\reir\AppData\Roaming\JDEVEL~1\SYSTEM~1.81\DEFAUL~1\config\FMWCON~1 -Digf.arisidbeans.carmlloc=C:\Users\reir\AppData\Roaming\JDEVEL~1\SYSTEM~1.81\DEFAUL~1\config\FMWCON~1\carml -Digf.arisidstack.home=C:\Users\reir\AppData\Roaming\JDEVEL~1\SYSTEM~1.81\DEFAUL~1\config\FMWCON~1\arisidprovider -Doracle.security.jps.config=C:\Users\reir\AppData\Roaming\JDEVEL~1\SYSTEM~1.81\DEFAUL~1\config\fmwconfig\jps-config.xml -Doracle.deployed.app.dir=C:\Users\reir\AppData\Roaming\JDEVEL~1\SYSTEM~1.81\DEFAUL~1\servers\DefaultServer\tmp\_WL_user -Doracle.deployed.app.ext=\- -Dweblogic.alternateTypesDirectory=C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.ossoiap_11.1.1,C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.oamprovider_11.1.1 -Djava.protocol.handler.pkgs=oracle.mds.net.protocol -Dweblogic.jdbc.remoteEnabled=false -Dwsm.repository.path=C:\Users\reir\AppData\Roaming\JDEVEL~1\SYSTEM~1.81\DEFAUL~1\oracle\store\gmds -Dweblogic.management.discover=true -Dwlw.iterativeDev= -Dwlw.testConsole= -Dwlw.logErrorsToConsole= -Dweblogic.ext.dirs=C:\Oracle\MIDDLE~1\patch_wls1035\profiles\default\sysext_manifest_classpath;C:\Oracle\MIDDLE~1\patch_jdev1112\profiles\default\sysext_manifest_classpath weblogic.Server
Error occurred during initialization of VM
Error opening zip file or JAR manifest missing : ../modules/org.eclipse.persistence_1.1.0.0_2-1.jar
agent library failed to init: instrument
Process exited.

This issue is usally caused by missing rt.jar. It's a good idea to manually unpack libraries.
Look for your java library directory (usually jre<version>/lib) .
If you can see rt.pack and can't see rt.ajr -
make the follwoing (I consider you save this to a script file then run it and your JAVA_HOME is correctly set and you're using some sort of UNIX):
---------------------------------cut---------------------------------
#!/bin/sh
JH=${JAVA_HOME:-"/usr/java/jre1.5.0_04"}
UNPACK_EXE=$JH/bin/unpack200
if [ -f $UNPACK_EXE ]; then
chmod +x $UNPACK_EXE
PACKED_JARS="lib/rt.jar lib/jsse.jar lib/charsets.jar lib/ext/localedata.jar lib/plugin.jar lib/javaws.jar lib/deploy.jar"
for i in $PACKED_JARS; do
srcFile=${JH}/`dirname $i`/`basename $i .jar`.pack
dstFile=${JH}/$i
if [ ! -f $srcFile ]; then
printf "Error: Unable to find %s. Please, check out your installation.\n" $srcFile
exit 1
fi
$UNPACK_EXE $srcFile $dstFile
if [ ! -f $dstFile ]; then
printf "Error: unpack could not create %s. Please refer to the Troubleshooting\n" $dstFile
printf "Section of the Installation Instructions on the download page.\n"
exit 1
fi
rm -f $srcFile
done
else
printf "Error: unpack command could not be found. Please refer to the \n"
printf "TroubleShooting Section of the Installation Instructions on \n"
printf "the download page.\n"
printf "Please do not attempt to install this archive file.\n"
exit 2
fi
---------------------------------cut---------------------------------

Error occurred during initialization of VM. Could not reserve enough space

Dear All,
I am trying to install SAP NetWeaver 7.0 SR2 SP9 on Oracle 10.2 and platform is Windows 2003 32 bits. While installing, in t he restarting the JAVA Instance step, server0 node is getting shutdown. When I further analyzed dev_server0 log, I could get below useful information:
Error occurred during initialization of VM
Could not reserve enough space for object heap
[Thr 6008] JLaunchIAbortJava: abort hook is called
[Thr 6008] **********************************************************************
*** ERROR => The Java VM aborted unexpectedly.
*** Please see SAP Note 943602 , section 'Java VM crashes'
*** for additional information and trouble shooting.
[Thr 6008] JLaunchCloseProgram: good bye (exitcode = -2)
I referred the note mentioned above and it inturn referred to note# 940893. I followed many other sap notes also. However my above problem did not solve yet. I have checke my JAVA SDK version also. It is j2sdk1.4.2_11 and seems to be fine. My systems memory is 3 GB and I gave 20 GB as Virtual memory. I dont think that it should be a memory problem. However somewhere I am lost and can not get the grip over the problem to resolve it.
May I request all of you to kindly help me on above issue? Please let me know if you need any more information.
Waiting for your kind replies.
Regards,
Faisal

Dears,
Thank you very much for your replies. The heap size was 1024. I changed it to the below:
Heap Size=512 (earlier 1024)
Changed below paramters in configtool:
-Xmx512m (earlier 1024)
-Xms256m (earlier 1024)
Hope this information will be helpful to others as well.
Once again, I thank both of you to guide me in proper directions.
Regards,
Faisal

Error occurred during initialization of VM Using Whs

RDBMS Version: 9i
Operating System and Version: Microsoft Windows 2000 server Service pack 4
Product: Oracle Lite, 9i
AS: 9.0.2.3
When I use the wsh.exe in cmd.exe I have the error:
D:\oracle\prodotti\Ora9iasfe\Mobile\Server\bin>wsh
Error occurred during initialization of VM
Could not reserve enough space for object heap
Environment info:
D:\Documents and Settings\Administrator>java -version
java version "1.3.1_03"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.3.1_03-b03)
Java HotSpot(TM) Client VM (build 1.3.1_03-b03, mixed mode)
D:\Documents and Settings\Administrator>set classpath
CLASSPATH=D:\MOBILECLIENT\Mobile\bin\olite40.JAR;D:\Programmi\JavaSoft\JRE\1.3.1_03\bin;d:\oracle\pr
odotti\Ora9iasfe\MOBILE\CLASSES\OLITE40.JAR;d:\oracle\prodotti\Ora9iasfe\j2ee\home\oc4j.jar;d:\oracl
e\prodotti\Ora9iasfe\j2ee\home\lib\ojsp.jar;d:\oracle\prodotti\Ora9iasfe\jlib\zrclient.jar;d:\oracle
\prodotti\Ora9iasfe\reports\jlib\rwrun.jar;d:\oracle\prodotti\Ora9iasfe\jlib\bigraphbean.jar;d:\orac
le\prodotti\Ora9iasfe\jlib\LW_PfjBean.jar;d:\oracle\prodotti\Ora9iasfe\jlib\bigraphbean-nls.zip;d:\o
racle\prodotti\Ora9iasfe\Mobile\Server\bin\webtogo.jar;
D:\Documents and Settings\Administrator>set path
Path=D:\Programmi\JavaSoft\JRE\1.3.1_03\bin;d:\oracle\prodotti\Ora9iasfe\bin;d:\oracle\prodotti\Ora9
iasfe\Mobile\Server\bin;d:\oracle\prodotti\Ora9iasbe\bin;d:\oracle\prodotti\Ora9iasfe\bin;d:\oracle\
prodotti\Ora9iasfe\jdk\jre\bin\classic;d:\oracle\prodotti\Ora9iasfe\jdk\jre\bin;d:\oracle\prodotti\O
ra9iasfe\jlib;d:\oracle\prodotti\Ora9iasbe\jlib;D:\Programmi\Oracle\jre\1.3.1\bin;D:\Programmi\Oracl
e\jre\1.1.8\bin;D:\WINNT\system32;D:\WINNT;D:\WINNT\System32\Wbem;d:\oracle\prodotti\Ora9iasfe\bin\;
D:\PROGRA~1\ULTRAE~1;d:\oracle\prodotti\Ora9iasfe\MOBILE\sdk\bin
Thanks
Rino

RDBMS Version: 9i
Operating System and Version: Microsoft Windows 2000 server Service pack 4
Product: Oracle Lite, 9i
AS: 9.0.2.3
When I use the wsh.exe in cmd.exe I have the error:
D:\oracle\prodotti\Ora9iasfe\Mobile\Server\bin>wsh
Error occurred during initialization of VM
Could not reserve enough space for object heap
Environment info:
D:\Documents and Settings\Administrator>java -version
java version "1.3.1_03"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.3.1_03-b03)
Java HotSpot(TM) Client VM (build 1.3.1_03-b03, mixed mode)
D:\Documents and Settings\Administrator>set classpath
CLASSPATH=D:\MOBILECLIENT\Mobile\bin\olite40.JAR;D:\Programmi\JavaSoft\JRE\1.3.1_03\bin;d:\oracle\pr
odotti\Ora9iasfe\MOBILE\CLASSES\OLITE40.JAR;d:\oracle\prodotti\Ora9iasfe\j2ee\home\oc4j.jar;d:\oracl
e\prodotti\Ora9iasfe\j2ee\home\lib\ojsp.jar;d:\oracle\prodotti\Ora9iasfe\jlib\zrclient.jar;d:\oracle
\prodotti\Ora9iasfe\reports\jlib\rwrun.jar;d:\oracle\prodotti\Ora9iasfe\jlib\bigraphbean.jar;d:\orac
le\prodotti\Ora9iasfe\jlib\LW_PfjBean.jar;d:\oracle\prodotti\Ora9iasfe\jlib\bigraphbean-nls.zip;d:\o
racle\prodotti\Ora9iasfe\Mobile\Server\bin\webtogo.jar;
D:\Documents and Settings\Administrator>set path
Path=D:\Programmi\JavaSoft\JRE\1.3.1_03\bin;d:\oracle\prodotti\Ora9iasfe\bin;d:\oracle\prodotti\Ora9
iasfe\Mobile\Server\bin;d:\oracle\prodotti\Ora9iasbe\bin;d:\oracle\prodotti\Ora9iasfe\bin;d:\oracle\
prodotti\Ora9iasfe\jdk\jre\bin\classic;d:\oracle\prodotti\Ora9iasfe\jdk\jre\bin;d:\oracle\prodotti\O
ra9iasfe\jlib;d:\oracle\prodotti\Ora9iasbe\jlib;D:\Programmi\Oracle\jre\1.3.1\bin;D:\Programmi\Oracl
e\jre\1.1.8\bin;D:\WINNT\system32;D:\WINNT;D:\WINNT\System32\Wbem;d:\oracle\prodotti\Ora9iasfe\bin\;
D:\PROGRA~1\ULTRAE~1;d:\oracle\prodotti\Ora9iasfe\MOBILE\sdk\bin
Thanks
Rino

Error occurred during initialization of VM & java/lang/NoClassDefFoundError

ascertain:tcglive:~/BUILD/bin> ./listJobs
Error occurred during initialization of VM
java/lang/NoClassDefFoundError: java/lang/Object
ascertain:tcglive:~/BUILD/bin> ./startJobServer -fg
Error occurred during initialization of VM
java/lang/NoClassDefFoundError: java/lang/Object
We've been trying to get rmiregistry started but have noticed the following discrepancy on the server.
ascertain:tcglive:~> which java
/usr/bin/java
ascertain:tcglive:~> echo $JAVA_HOME
/usr/local/j2sdk1.4.2_03
There are conflicting versions of java on this box and even though 1.4.2 has been specified in $JAVA_HOME, the environment does not seem to recognise this:
ascertain:tcglive:~> java -version
java version "1.2.2"
Solaris VM (build Solaris_JDK_1.2.2_10, native threads, sunwjit)

What does
which javasay?

Error occurred during initialization of VM .. any sugesstion

Hi,
I tried to call the helloworld program from a C program in linux.
but i got the following error message
Error occurred during initialization of VM
Unable to load native library: libverify.so: cannot open shared object file: No such file or directory
Can any one give me suggestion of what could be wrong.
The same program, I was able to execute in windows and in solaris platform.
kabilesh

Most likely the lib is not in your shared library path.
Or the permissions are wrong (file or directories.)

Error occurred during initialization of VM Could not reserve enoughspace for code cache

I receive this error in the ZENWSimport and Removal screen:
Error occurred during initialization of VM
Could not reserve enough space for code cache
Server is a HP DL380G4, NWSBS SP5, 4 GB RAM.
I think it's Java related, because iManager also stopped working (error
503 - service unavailable)
AUTOEXEC.BAT:
@echo off
prompt $p$g
path=c:\dos
rem mscdex /d:cpqcdrom /v /m:50 /l:f
c:\dos\nlsfunc
c:\dos\mode con cp PREPARE=((437) c:\dos\EGA.cpi)
c:\dos\mode con cp Select=437
cd \NWSERVER
## commented by MemCalc server -nl -u134217728
server -nl -u134217728
I tried removing the -u switch, but the server wouldn't even boot then.
I'm out of options, can anyone help?
Arjan Schepers

Also, I reapplied Service Pack 5, didn't help. BTI.CFG looks like the
following:
;* Copyright 1982-2001 Pervasive Software Inc. All Rights Reserved
;* Pervasive Software product initialization file for NetWare
[Btrieve Communications Manager]
MaxWorkerThreads=16
MaxReceivePacketSize=1500
Supported Protocols=TCPIP
Listen IP Address=
TCP/IP Multihomed=YES
Enable AutoReconnect=NO
AutoReconnect Timeout=180
[MicroKernel]
CacheSize=2048000
Pervasive SQL 9SP2 is installed on this server for an application named
MICROS RAS/KAS. It needs 2GB memory (*shrug*, I know), hence the 4GB memory.
Arjan Schepers

Error occurred during initialization of VM, could not reserve space in heap

I installed the SOA suite+ BPM 11.1.1.3.0, ESB 11.1.1.3.0 successfully along with RCU schema in oracle DB Ex edition 11 G successfully. I have 2 GB Ram in my system. I am facing the below error during the startup of weblogic instance which is having these all ESB, BPM properties.
it seems that 2 GB ram is occupying by the SOA suite.
CAN ANY ONE SUGGEST TO REDUCE THE SOA SUITE RAM CAPACITY.
USER_MEM_ARGS=-Xms512m -Xmx1024m -XX:PermSize=128m -XX:MaxPermSize=512m
JAVA_OPTIONS= -Xverify:none
** End SOA Specific environment setup for win.
** SOA specific environment is already set. Skipping ...
JAVA Memory arguments: -Xms512m -Xmx1024m -XX:PermSize=128m -XX:MaxPermSize=512m
WLS Start Mode=Development
CLASSPATH=C:\Oracle\MIDDLE~1\WLSERV~1.3\server\ext\jdbc\oracle\11g\ojdbc6dms.jar;C:\Oracle\Middleware\Oracle_SOA1\soa\modules\user-patch.jar;C:\Oracle\Middleware\Oracle_SOA1\soa\modules\soa-startup.jar;;C:\Oracle\MIDDLE~1\patch_wls1033\profiles\default\sys_
Error occurred during initialization of VM
Could not reserve enough space for object heap
Regards
Raghu Veer

Hello Raghu,
As James indicated it is problem with the system configuration but still you may try below once -
Go to $Domain_Home/bin and edit the setSOADomainEnv.cmd (or setSOADomainEnv.sh) to change below setting -
set DEFAULT_MEM_ARGS=-Xms512m -Xmx512m
If you are using AMD processor then modify below instead of DEFAULT_MEM_ARGS -
set PORT_MEM_ARGS=-Xms768m -Xmx768m
Save and exit.
Now start Admin server and after that SOA server and OSB server. As James suggested, for better performance you may keep either of SOA and OSB server up as and when required and keep other one down.
I am still using a 2GB machine for 11g suite and I work easily because generally I work with one of SOA or OSB server and whenever I use any IDE like JDev or OEPE, I keep all servers down. For better performance and memory utilization you may use Oracle XE database.
Hope it helps.
Regards,
Anuj

Get pdf filename during initialize:

I wonder to get the pdf filename during initialize, may i know is it possible?
Thanks your concern.
Tham

ASFileSysOpenProc is not suitable. It is used for the opening of all
files, not just PDF files, and you do not provide it for the standard
filesystem: it is a standard part of Acrobat.
Since it is documents you are interested in, rather than files, you
would want to look at the document related callbacks (CosDoc, PDDoc,
AVDoc). I can see why you wouldn't find it though, the Acrobat API
documents are breathtakingly awful, ever since someone had the bright
idea of replacing a human editor with a programmer generated file.
You need to use the PDDocDidOpen notification (notification is the
buzzword here, not callback), registered with
AVAppRegisterNotification. Try documents from an older version of the
SDK, the Acrobat 8 SDK is beyond a joke.
Aandi Inston

DB13 error: 0003 Error during initialization

Dear All,
Since last 2 days, Production backup is getting failed with error "0003 Error during initialization".
Strangely, there are no related logs to investigate further... Nothing was changed in backup related configurations.
We are using Tivoli (TSM) backup solution..
System Details: HP-UX 11.31i, Oracle10g (10.2.0.4), ECC 6.0
In DB13 Action logs, it is showing following details only...
Action: Whole database offline backup
Brbackup logfile : bedjjsnb.log ##### Actually it should show filename something like "bedjjsnb.aff"
Return Code : 0003 Error during initialization
When I click on "Show Actiion/Detail log", it shows nothing... (Log file does not exists..)
There is no file with above filename in /oracle/<SID>/sapbackup and in back<SID>.log
I have checked below things :
1. BRTOOL permissions (As per note 113747 - Permissions for DBA tools BRTools and SAPDBA)
2. /oracle/<SID>/sapbackup permissions (it is 755 with ora<sid>:dba ownership)
3. I have checked /var/adm/syslog/syslog.log, but there is no error.
4. Test for communication between SAP server and Tivoli is OK.
5. TSM Session query is also returning desired result.
6. I made sure that there are free and scratched tape in TSM for SAP backup pool.
7. No other backup was running at the time of SAP backup.
I have tried taking backup on DISK which is successful without any errors or warnings.
What else I can check ? Am I missing something ?
Any inputs will be highly appreciated...
I will try to fire backup manually later in the evening after business hours to see what exactly going wrong in between.
Regards.
Rajesh Narkhede

Hi John,
See the last few lines from output below: (SID and Hostname removed...)
BR0110I Backup mode: ALL
BR0077I Database files for backup:
/oracle/<SID>/origlogA/log_g11m1.dbf
/oracle/<SID>/origlogB/log_g12m1.dbf
/oracle/<SID>/origlogA/log_g13m1.dbf
/oracle/<SID>/origlogB/log_g14m1.dbf
/oracle/<SID>/origlogA/cntrl/cntrlHRP.dbf
BR0061I 53 files found for backup, total size 133738.270 MB
BR0143I Backup type: offline
BR0130I Backup device type: util_file
BR0109I Files will be saved by backup utility
BR0124I Query option set - no processing
BR0056I End of database backup: bedjndvn.qub 2010-06-04 17.01.32
BR0280I BRBACKUP time stamp: 2010-06-04 17.01.32
BR0052I BRBACKUP completed successfully
<HOSTNAME>:ora<sid>>
Nothing seems to be wrong...
Regards.
Rajesh Narkhede

ECC Error occurred during initialization of VM

Hi guys,
when I installed ecc6 into the suse-10 which is on the Vmware Server 1.0.3, when I installed oracle,there showed some mistakes,
/oracle/stage/102_64/database/SAP/SVRCUSTOM.RSP --> /tmp/.orainst_rsp.6246: Done
Starting Oracle Universal Installer...
Checking installer requirements...
Checking operating system version: must be redhat-3, SuSE-9, SuSE-10, redhat-4, UnitedLinux-1.0, asianux-1 or asianux-2
Passed
All installer requirements met.
Preparing to launch Oracle Universal Installer from /tmp/OraInstall1912-09-24_09-47-39AM. Please wait ...oraecc@sap01:/oracle/stage/102_64/database/SAP> Error occurred during initialization of VM
java.lang.ExceptionInInitializerError
1、the sap's graph was normal.
2、when I installed SuSE, I chose the component of SAP and Oracle which contained some rpms,such as saplocales,orarun...
and in that time, it show the dependency conflict, and I chose ingore. (as I haved tried to choose one of them ,but then failed.)
pls someFriends help me.
BestRegards!

Hi,
Have you checked the following notes:
Note 958253 - SUSE LINUX Enterprise Server 10: Installation notes
Note 1122387 - Linux: SAP Support in virtualized environments
Kind regards,
Mark

Forcedeth on MPC55 "no link during initialization" no net cable detect

Similar Messages

Maybe you are looking for