Freshclam running when it shouldn't

On our Mac Mini server running 10.6.4 I'm getting the following message every 30 seconds in the console:
org.clamav.freshclam[53] Can't connect to port 80 of host database.clamav.net (IP: 168.143.19.95)
As I understand it, freshclam is part of an anti-virus package that scans email. The problem is that our server is not running a mail server. Why is freshclam running at all? How can I turn it off?
org.clamav.freshclam does not show up when I run "launchctl list". If I just kill freshclam in Activity Monitor, launchd just restarts it.
Thanks in advance for any help.
- Steve

it should show up with:
launchctl list | grep fresh
are you sure the plist is disabled? did you ever upgrade clamav/freshclam?

Similar Messages

RT does not run when deployed to 9642 sbRIO LV 2011

I have code deployed to a Ni sbRIO9642 where the RT code does not run when deployed to the when using LabVIEW 2011. It appears the NI-RT.ini file on the target is not being properly configured. I manually configured the ini file using FTP and the RT still will not run. I built a small test application and the RT on that did not run either, although i had hard validatiuon that the FPGA code was indeed running. Thanks - Keith

Hey Martin,
I don't know if this specific problem was resolved, but there was a known issue in LabVIEW Real-Time 2011 (sp1) that exhibited this behavior.
Shared Variables
292012
Return
Real-Time Applications containing typedef Shared Variables fail to run.
If you are building an RTEXE that contains Shared Variables whose data type is based upon a type definition and the build specification is configured to disconnect type definitions the RTEXE will not run.
Workaround: 1.) Manually disconnect the variable from the typedef before building the application 2.) Change the build spec so it doesn't disconnect type definitions
Reported Version: 2011 32-bit
Resolved Version: 2012
Added: 10/11/2011
Although this has been fixed in 2012, and shouldn't be an issue for you developing in LabVIEW 2012. Have you tried implementing a heartbeat VI? to verify if your RT app is actually running and not communicating? (great example here)
Do you have the system state pushier installed on your cRIO? does it point to a memory leak or 100% CPU utilization? (steps to install it found here, if you're not familiar)
Are you using the cRIO in Scan Interface mode? or in the FPGA interface?
Applications Engineer
National Instruments
CLD Certified

How to tell embedded jinitator applet is still running when window closed

Hello, we are trying to accomplish the same thing that is mentioned in this post from Metalink. I've searched for a solution and hope someone here can help. Instead of restating the issue I think David Wilson does a good job of explaining what is needed. Can anyone please suggest a possible solution?
From: David Wilton 07-Oct-05 01:08
Subject: How to tell embedded jinitator applet is still running when window closed
How to tell embedded jinitator applet is still running when window closed
Hi,
We run an oracle 10g forms application through 9iAS over an intranet. All users are running windows 2000 professional.
We run separate frame = true but I would like to switch to separate frame = false
With separate frame = true if the user clicks the outer windows "X" close button (forms mdi window) the user is prompted to save changes before the application ends.
BUT
when using separate frame = false
If the user clicks the upper window "X" button (no longer form mdi window but regular browser window) the window and application is abruptly closed.
I'm interested in using a onbeforeunload function to confirm if the user wants to close the window. This would be placed in the basejini.htm file. This could always ask if the user wants to exit or not. If they click OK then the window closes but if they click "Cancel" you are returned to the forms application exactly where you left. something like event.returnvalue="do you really want to exit?";
However if the user exited using the normal exit form method then the applet is already closed before the onbeforeunoad event fires and there is nothing to go back to and I want the window to close automatically. This is accomplished using close.html file in post forms trigger.
So what I want and what I think many may also want is the check if the embedded applet is still running and if so prompt the user to return to the application or continue to close. Of course If the applet is no longer running then just close because there is no reason confirm closing anymore.
Does anyone have a html/JavaScript solution that can be placed in the jinitiator.htm file? or similar?
Thank you
David
[email protected]
From: Andrew Lenton 07-Oct-05 08:58
Subject: Re : How to tell embedded jinitator applet is still running when window closed
I don't know if this is exactly what you are after but you can add the following to the top of your basejini.htm file and it should prompt the user before exiting the IE window.
<BODY %HTMLbodyAttrs%>
%HTMLbeforeForm%
<SCRIPT>

</SCRIPT>
From: Oracle, mohammed pasha 07-Oct-05 09:55
Subject: Re : How to tell embedded jinitator applet is still running when window closed
David,
Well I could not understand your complete requirement.
Refer to Note.201481.1 How to Close the Browser Window When Closing Forms And How to Simulate SeparateFrame By Javascript
Note.115905.1 How to Close Browser Window When Closing Webforms Applet
Kind Regards,
Anwar
From: David Wilton 07-Oct-05 14:37
Subject: Re : How to tell embedded jinitator applet is still running when window closed
Thank you for your reply and yes you did not understand my question fully.
Sorry if this is a long reply
I am able to close the browser window using information in notes 115905.1 and 201481.1, this is not the issue. We implemented this several years ago. It is workable for both separate frame = true or false.
It is most important to not allow the user to end their forms application by closing the windows browser, they must close using normal form exit commands.
What I want is to have separate frame = false, the big drawback to this option is the user can exit the application and bypass all forms code by pressing the windows "X" close button. This is why we need the code as just provided by Andrew Lenton above in this thread.
BUT Andrew's code will always prompt the user before closing the window and I do not want that. I want the user to be prompted only under scenario 2 listed below.
Here's the 2 case scenario for exiting the application.
1. If the user closes properly and uses exit form which fires all normal form triggers including post_form with it's call to close.html file.
All uncommitted changes are saved or rollback and the users session is ended normally both on the database and in the application server.
All browser windows will close, great all is good. And without Andrew's code the window will close but with Andrew's code the user will be prompted to close or not, if they select Cancel the window will remain but the applet has already ended so why prompt? ...This is what I want to avoid.
2. In the forms app. if the user clicks the windows "X" close button with uncommitted changes. The browser just closes the changes are rollback without prompting the user to save. The users sessions are now lost and still running in the database and application server until they are timed out.
If I use Andrew's code then the user will be prompted to continue to close or go back, if they click Cancel to go back then focus returns to the forms application and the user can continue to work. If the user clicks OK then the window closes and unfortunately their sessions are still lost until timed out.
So what I desire is to add to Andrew's code to check if the embedded applet is still running and prompt the user to close or not accordingly.
Something like:
Basejini.htm like
</HEAD>
<SCRIPT LANGUAGE="JavaScript">
function maximizeWindow()
window.moveTo(0,0);
window.resizeTo(screen.availWidth,screen.availHeight);
function confirm(){
If(document.embeddedapplet.closed())
Win.opener = self;
win.close();
Else if
event.returnValue = "Closing Forms Application. OK to continue?";
</SCRIPT>
<BODY %HTMLbodyAttrs%, onload="maximizeWindow()", onbeforeunload="confirm()">
%HTMLbeforeForm%
I hope this explains my requirements.
David
From: Oracle, Evelene Raechel 10-Oct-05 06:45
Subject: Re : How to tell embedded jinitator applet is still running when window closed
Hi,
Note.199928.1 How to Alert User on Closing Client's Browser Window in Webforms
Regards,
Rachel
From: David Wilton 11-Oct-05 17:40
Subject: Re : How to tell embedded jinitator applet is still running when window closed
I'm sorry this is not helpful at all.
Note 199928.1 is only an alert which does not stop the closing of the window and still displays as an alert if the user does close properly using exit form ... so why would you want to display the alert then?
This is exaclty what I do not want and why I want to determine if the applet is still running before displaying any kind of message.
David
From: Oracle, Evelene Raechel 17-Oct-05 12:23
Subject: Re : How to tell embedded jinitator applet is still running when window closed
Closing thread.
Thanks,

Hello,
I had the same issue last year - wanting to provide a warning on closing the browser, but only if the Forms session is still running. The approach I took is described below, see also the thread where I originally posted this at Closing brower window
Hi there,I've had a similar requirement - or rather, the two conflicting requirements: to warn when the browser is being closed, but for the app to be able to close the browser without a warning being fired.
To always provide a warning when someone (the user or the Forms app) tries to go to a different page (e.g. your close.htm), use Javascript like:
function confirmExit(){
if(appletRunning==true) {
msg="Closing this window or navigating to another page will end your SomeGreatApp session.";
window.event.returnValue=msg;
And make a call to confirmExit() in the onBeforeUnload event of your main page.
You'll notice I first check an 'appletRunning' variable before displaying the warning. This Javascript variable is set to true by my app when it starts up, using an embedded Javabean that calls out to Javascript. Once that variable is set to true, then the warning will be displayed if the user tries to shut the browser by clicking on the 'x' button, or to go to a different URL.
When my app is shutting down, it uses the same Javabean to set appletRunning back to false. It then navigates to a close.htm - which will be done without a warning being displayed.
See Re: How can a Javabean call Javascript function of the basejpi.html?? for example code on how to call Javascript from a bean embedded in your Forms app.
Hope these ideas help you out, it's worked for me (so far, anyway!!)
James

How can I disable the Photos app from automatically running when I plug in my iPhone?

How can I disable the Photos app from automatically running when I plug in my iPhone?
I have no intention of ever using Photos, in fact, having to abandon Aperture takes me one step close to moving back to Windows, but I digress.
I just want to NOT have to kill the Photos app every time I plug in my phone.
Thanks.

I am still seeing the option Image Capture, like shown in the screenshot that Rysz posted. But it is another example of the hide-and-seek Apple likes to play with us.
The option has to be set for each device individually. With the device connected to USB, you have to click the tiny disclosure triangle in the lower left corner of the sidebar to reveal the option.
I was perfectly happy with the program I paid for (Aperture), and now to maintain the functionality I have to pay for another application (LightRoom) to get the functionality that I paid for in Aperture.
Aperture 3.6 is working well with Yosemite. I will use it, as long as I have a Mac, that will run Yosemite or a compatible system.
Have you looked at Capture One? It looks much more similar to Aperture than Lightroom.

Accidentally deleted firefox "profiles.ini" and now says firefox is already running when I try to open it.

Accidentally deleted firefox "profiles.ini" and now says firefox is already running when I try to open it. "a copy of firefox is already open. only one copy of firefox can be open at one time. Now I'm aware this happens often and people have posted solutions to this, but this situation is slightly different. The "profiles" that possibly had parental lock on it were deleted and I don't know how to get it back. Re-downloading firefox obviously does nothing. Opening the task manager and to try and close all mozilla/firefox files and apps doesn't work either. Tried using Onyx to turn invisible files visible but that didn't work either. I think it's cause I deleted the profiles. Suggestions?

Any chance of restoring that profiles.ini file via the Time Machine?
*http://kb.mozillazine.org/profiles.ini_file
If not then you need to use the Profile Manager to re-register that no longer recognized profile.<br />
You do that by creating a new profile and use Choose Location to point the your lost profile.
*http://kb.mozillazine.org/Profile_in_use
*http://kb.mozillazine.org/Recovering_a_missing_profile

Is it possible to have a VI "run when opened" when accessed via Internet Explorer?

I am trying to get a remote panel application to "run when opened" when is accessed via Internet explorer. I have multiple remote panel licenses on the server and the VI is Re-entrant. The application works well except for this issue. Having the VI "Run When Opened" via IE is very important to the user. As is, when IE opens, the user must click on the panel image once to get the VI's attention and then again on the start arrow to run the program. Is there any way around this or a way to simplify the process?
Thanks.
Solved!
Go to Solution.

This is actually the intended operation of remote front panels, however, we can simplify the operation to meet closer with what your customer wants. Basically, if you were to always have your program run in somewhat of an idle state, you can use the Application Control>>Property node for 'RemotePanel.ConnToClients' property to determine when a user is connected and run the proccess of the program as soon as a connection is detected. When no connection is detected you could have the program run in an idle state. The attached screenshot shows a general way to do this. Have a good evening!
-Bob
-Bob
Attachments:
idle state.JPG ‏45 KB

HP OfficeJet Pro 8500 goes to sleep, but often wakes up when it shouldn't

HP OfficeJet Pro 8500 goes to sleep, but often wakes up when it shouldn't. This happens over and over. It used to sleep until I sent something to be printed. I now shut the printer down, but that takes a long time to start it up.

When you finally get around to looking at my post, never mind.
I reset the factory defaults on the printer and reauthorized my WiFi network.
Now it is working.

Podcasts are syncing when they shouldn't be

My iPod finally ran out of space so I wanted to remove some of the video podcasts from it. I have my podcast syncing set to sync the selected podcasts so I thought I could just uncheck the ones I didn't want to keep on my iPod and sync to remove them. That didn't work so I put my iPod in manual sync mode and removed them. I turned off the manual sync option and told it to sync again and it's copying all my podcasts (even the ones that aren't checked on the podcast tab). How do I make it stop so I can free up some space?

Ok, I can confirm that the problem doesn't affect music playlists.
I've also noticed that the files that get copied when they shouldn't take up more space than the ones that are supposed to be there. I noticed this by syncing, checking a podcast that was previously unchecked, then resyncing. It wasn't a lot of space, only around 10-25 mb.
I've also found a workaround to get the files off my iPod. I have the "Sync only checked songs and videos" option checked on the summary tab for my iPod in iTunes. I can uncheck each individual podcast that I don't want to be on my iPod, then resync and they are removed. So I guess the problem is only present on the Podcasts (possibly movies and tv shows too) tab of the iPod screen in iTunes.
Is there somewhere else I should go to submit a bug report?

Firefox does not open, says it's running when trying to restart, but does not show up

Cannot get Firefox to visibly run. Will not open in safe mode and will not close (says its running when I attempt to shutdown or restart computer. Have uninstalled Firefox and reinstalled 8.0 several times and nothing has changed. Have scanned , defragmented, etc. computer and tried a couple system restores as this once cured similar problem with Firefox several months ago.

Bring up the Windows Task Manager, but look in the "Processes" tab for firefox.exe,
and close it from there, it won't do you any good looking for it in the "Applications"
tab when you don't see it on the system taskbar.
closing Firefox properly, and for when you just want to close and
restarting Firefox immediately, see more information in
: https://support.mozilla.com/questions/866027

ASE instance not available *** ERROR:ASE instance possibly left running when system went down(system crash?). Notify Database Administrator

Hi Gurus,
I made some changes in rz10 for client copy like:
icm/host_name_full [email protected]
login/accept_sso2_ticket 1
login/create_sso2_ticket 2
icm/server_port_1
PROT=HTTPS,PORT=443$$,PROCTIMEOUT=600,TIMEOUT=600
icm/server_port_0
PROT=HTTP,PORT=80$$,PROCTIMEOUT=600,TIMEOUT=600
login/no_automatic_user_sapstar 0
After to make changes effective, i stopsap & startsap.
But unfortunately db is not coming up. I checked startdb.log it showing
error as " ASE instance not available
*** ERROR:ASE instance possibly left running when system
went down(system crash?).
Notify Database Administrator."
Please help us to resolve this issue, i have also added startdb.log for
your reference.
Regards,
Piyush

Hi Piyush,
Did you solved this issue.
We are facing the same issue and only this thread is there in SCN for this issue.
If you solved this issue,Kindly share the solution.
Thanks and Regards,
Mathan A

AfterValueChange event trigged when it shouldn'tbe...

Hi there,
I'm hoping that someone out there has experienced the following (and
knows why it is happening. ) :-)
I have a couple of windows on which the AfterValueChange event is
triggered on a field upon hitting the delete key.
We all know that this should only happen upon leaving the field, ie. the
field loosing focus. The problem is that I'm trying to recreate this in
a simple test class, but now it won't happen. I still have the original
windows on which it is happening, but I would like to construct
something small and simple to send to Forte.
Any ideas as to why this could be happening?
Many thanks in advance.
Jaco
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>

Thanks for the replies so far, but this is not the problem. I know about
the "Validate on keystroke" option and it is definitely swithed off.
I was rather thinking along the lines of this being be a 'funny' in
Forte. Has anyone seen this before? Here is more information:
1) The windows that it is happening on all have parent windows.
2) The fields with this problem are all part of a mapped gridfield, ie.
it has a type.
However, I have constructed a test class with these characteristics, but
it is no good. There must be something else that could cause this. Any
ideas?
-----Original Message-----
From: Rottier, Pascal [SMTP:[email protected]]
Sent: Friday, October 09, 1998 10:53 AM
To: Fouche, Jaco
Cc: Forte Users Mailing list
Subject: RE: AfterValueChange event trigged when it shouldn't be...
Hi Jaco,
Check if the option "Validate on keystroke" is set
to true on the widget that posts the AfterValueChange.
If so, than that's the reason. Turn it off and your
problem will go away.
Pascal
Hi there,
I'm hoping that someone out there has experienced the following (and
knows why it is happening. ) :-)
I have a couple of windows on which the AfterValueChange event is
triggered on a field upon hitting the delete key.
We all know that this should only happen upon leaving the field, ie.
the
field loosing focus. The problem is that I'm trying to recreate this
in
a simple test class, but now it won't happen. I still have the
original
windows on which it is happening, but I would like to construct
something small and simple to send to Forte.
Any ideas as to why this could be happening?
Many thanks in advance.
Jaco
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive
<URL:http://pinehurst.sageit.com/listarchive/>
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>

Keep windows running when macbook closed using dvi-out?

Is there a way I can keep windows running when I close the lid on my macbook when using dvi out?
at the moment it goes to sleep and logs me out and the dvi out looses connection and goes dark.

in jad file add 2 more keys:
Background - True
FlipInsensitive - True
regards
piter

Why does compiled (EXE) VI run when you double-click the icon even though I un-checked "Run When Opened"?

My VI code uses the VI's that came with the NI USB-8451 USB-to-SPI converter. Before compiling I needed to use one of those VI's to select the particular USB device that I'm trying to address, then I click the Run button. But after I compile my code into an EXE file, and then double-click the executable file it immediately starts running without allowing me to select the USB device - even though I un-checked the "Run When Opened" box. In fact I also un-checked the Show Menu Bar and Show Scroll Bars boxes as well, yet it shows both of them. What am I doing wrong?

It seems silly to start and stop a built LabVIEW application from the toolbar. A complete application should always run and have the LabVIEW toolbar hidden. A user of you code is not supposed to be familiar with LabVIEW mechanics.
You should do all this in code. Really!
Do a nice state machine with at least two states. (1) a state for where the device has not been entered and is simply waiting for your input, and (2) another state that verifies your device input and hands it to the rest of the code for afterwards.
Still, what LabVIEW version do you have. Did you set the "run when openend" setting in the application builder for the desired VI or just in the VI itself?
LabVIEW Champion . Do more with less code and in less time .

Is there a standard script that runs when a projector stops?

I know there are a couple of scripts I can use to set things up when starting a Director movie (startMovie and PrepareMovie). But are there also scripts I can use that run when the user chooses to shut down a projector? I want to run a script that sets the user's screen rez back to its original setting before shutting the projector down.
Thanks!
Dewey

Yes, I am looking at that one. But isn't that script activated each time a .dir movie is exited, even if it opens a different .dir movie? Or, is it only activated when the 'PROJECTOR stops?
The script I want to run should only run when you exit the projector.
Dewey

Firefox hangs and will not allow me to access other programs running when I resize a pop up window, move a pop up window, accidentally right click flash content.

Firefox hangs and will not allow me to access other programs running when I resize a pop up window, move a pop up window, accidentally right click flash content.
== This happened ==
A few times a week
== Not sure when it statrted

Hi.
When this happens, please press CTRL+SHIFT+ESC and see how much RAM and CPU Firefox is using. If they're sky high, then... Well, that kind of issues are, unfortunately, more common and the we'd like. Thankfully, 99% of the cases are very easy to solve. However, you do need to diagnose what your exact problem is. Do this:
#run Firefox in safe-mode to disable all extensions and plugins. If this fixes your issues, be them with RAM or CPU usage, then you know it's a problem with plugins or extensions. Proceed to number 2. If safe-mode doesn't fix the issues, then read bellow, after this list;
#update all extensions and plugins in your Firefox. If this doesn't solve the issues, proceed to the following number;
#disable all extensions and plugins in your Firefox (not running safe-mode). Being certain that, as in safe-mode, the problems you're having have gone away, enable one plugin at a time. You should be certain that you WANT that plugin to be enabled, so keep your overall number of plugins as low as possible. When you encounter the problems, you know you've found a problematic plugin, so disable it for good. Keep enabling all plugins (except problematic ones) until you've gone through them all.
#enable one extension at a time. Again, be certain that you WANT that extension to be enabled, so keep your overall number of extensions as low as possible. When you encounter the problems, you know you've found a problematic extension, so disable it for good. Keep enabling all your extensions (except problematic ones) until you've gone through them all;
#you're done! You've fixed your problems with problematic add-ons.
Ok, if disabling all extensions and plugins through safe-mode didn't work to bring Firefox's CPU and RAM usage to good levels, then you have different issue. The most likely scenario is that you have a third party software running on your computer that is messing with Firefox. Do as follows:
#do a virus/malware check on your computer. If this doesn't fix it, proceed;
#disable all software running in the background that you don't want to have running in the background (in windows, this is done by pressing WINDOWS+R in your keyboard, typing "msconfig" (without the commas) and pressing enter. Now, under the "Startup" tab, you can uncheck the software you don't want, and reboot your system for changes to take effect. If you're unsure of what software you want running, ask someone with more experience). If this doesn't fix you issues with Firefox, proceed;
#check your firewall/antivirus/security suite for enabled functions/features that you don't want and/or may be conflicting with Firefox. You'll find that these features are most likely tied to Internet Security features, such as link scanners or URL checkers and the like. If you're not sure they are conflicting with Firefox, simply try to disable to see whether or not that's true. As long as you don't browse the web with your antivirus completely off and your firewall completely turned off, there should be no problems. If this doesn't solve the issues, proceed to the following number;
#check your operating system security options, mainly advanced options that are not configured by default. While it's very unlikely that this may be the cause of the problem (after all, it's the last item on the list), it's remotely possible. If this doesn't do it, I'm out of ideas. Except make sure you've followed my instructions correctly.

Freshclam running when it shouldn't

Similar Messages

Maybe you are looking for