FTP ERROR ASA CISCO
Hi Am getting below error while am try to copy image from ftp server.
aaaaaa# copy flash:flash:/asa821-k8.bin ftp
Source filename [/flash:/asa821-k8.bin]? asa821-k8.bin
Address or name of remote host []? xxxxxx
Destination filename [asa821-k8.bin]?
Writing file ftp://xxxxxx/asa821-k8.bin...
%Error writing ftp://1xxxxxx/asa821-k8.bin ()
Hi Vasanth,
Try like this...
ASA#copy flash: ftp:
Source filename []? asa821-kb.bin
Address or name of remote host []? xxxxxx
Destination filename [asa821-k8.bin]?
Make sure that you are able to ping the FTP server from ASA and FTP Server to ASA.... if needed you may need to allow the ACL to do with the FTP transfer......
enable ftp in asa
conf t# ftp mode passive to make asa to respond for ftp traffic.....
also look at the logs in ftp server app
Regards
Karthik
Similar Messages
-
CTM ERROR: ASA hardware accelerator init failed
Hi Guys, I have bought a refurbished firewall and upon reloading I see the following error from console. Is something that I can rectify?
Loading disk0:/asa904-k8.bin... Booting...
Platform ASA5510
Loading...
IO memory blocks requested from bigphys 32bit: 13264
dosfsck 2.11, 12 Mar 2005, FAT32, LFN
Starting check/repair pass.
Starting verification pass.
/dev/hda1: 104 files, 12459/63613 clusters
dosfsck(/dev/hda1) returned 0
Processor memory 864026624, Reserved memory: 62914560
Total SSMs found: 0
Total NICs found: 7
mcwa i82557 Ethernet at irq 11 MAC: d0d0.fd1d.5d57
mcwa i82557 Ethernet at irq 5 MAC: 0000.0001.0001
i82547GI rev00 Gigabit Ethernet @ irq11 dev 1 index 05 MAC: 0000.0001.0002
i82546GB rev03 Ethernet @ irq09 dev 2 index 03 MAC: d0d0.fd1d.5d5b
i82546GB rev03 Ethernet @ irq09 dev 2 index 02 MAC: d0d0.fd1d.5d5a
i82546GB rev03 Ethernet @ irq09 dev 3 index 01 MAC: d0d0.fd1d.5d59
i82546GB rev03 Ethernet @ irq09 dev 3 index 00 MAC: d0d0.fd1d.5d58
Verify the activation-key, it might take a while...
Running Permanent Activation Key: 0x6122cb5d 0xc06c1a74 0xec92a120 0xbd44e8e8 0x8e372a8a
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 100 perpetual
Inside Hosts : Unlimited perpetual
Failover : Active/Active perpetual
Encryption-DES : Enabled perpetual
Encryption-3DES-AES : Enabled perpetual
Security Contexts : 2 perpetual
GTP/GPRS : Disabled perpetual
AnyConnect Premium Peers : 2 perpetual
AnyConnect Essentials : Disabled perpetual
Other VPN Peers : 250 perpetual
Total VPN Peers : 250 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
UC Phone Proxy Sessions : 2 perpetual
Total UC Proxy Sessions : 2 perpetual
Botnet Traffic Filter : Disabled perpetual
Intercompany Media Engine : Disabled perpetual
Cluster : Disabled perpetual
This platform has an ASA 5510 Security Plus license.
CTM ERROR: ASA hardware accelerator init failed, cause: boot_init completion timeout, ctm_nlite_boot_init:2284
CTM ERROR: ASA hardware accelerator init failed, cause: boot initialization failure, ctm_nlite_download:3342
CRYPTO ERROR: Microcode download failure, boot instance 0
Cisco Adaptive Security Appliance Software Version 9.0(4)
Thanks in advanceHi Mike,
Thanks for your reply. Considering it was at an early stage I had asked the supplier to replace it.
Regards
Stefan -
How to configure external FTP backup server CISCO NCS 1.1
How do you configure a external FTP Server for Cisco NCS 1.1? I only get setup username/password, i also need to setup FTP server IP and directory.
from the CLI you setup a repository,
conf t
repository FTP
url ftp://
username < username> password
exit
http://www.cisco.com/en/US/docs/wireless/ncs/1.0/command/reference/cli_app_a.html#wp1013913
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered -
Dreamweaver is locking me out when I try to connect to the host via ftp. I get the error message: "An ftp error has occurred - cannot make connection to host". This error message started yesterday when I used the wrong host ftp address too many times. I have since received the correct ftp address from my website host, but the system won't even let me log in...it just gives me that error message when I click the connection button on the panel. My website host recommends that I uninstall Dreamweaver and re-install it again. My concern is, if I un-install the Dreamweaver app, which I downloaded from the Cloud, will the Cloud know I've un-installed Dreamweaver and allow me to download it again? Please help.
See my response in your most recent thread. Please don't double post like that - it can confuse things considerably when replies come in to both threads.
-
An FTP Error occured - cannot make connection to host. No response from the server
"An FTP Error occured - cannot make connection to host. No response from the server".
As of today this is all i get when trying to connect to every single ftp account i have. It's not the server cause it's every one and there is several different. Tried passive and non-passive same result. I've connected fine with other FTP clients. So this must be another dreamweaver bug. Anyone know what to do?Very hard to diagnose these problems, particularly as you can connect using a 3rd party program.
See if the 'timeout' issue could be at play here:
http://forums.adobe.com/message/708941#708941 -
Hi,
Iam using a J2se file adapter for connecting to a FTP and picking the files.The following error has been shown and could't process the files-
13:09:40 (4029): Process 1 file(s):
13:09:40 : example.txt
13:09:58 (4030): Start processing "BIN" file "example.txt" size 69426 in "EO mode
13:09:58 (4032): Sending binary message "c7e7c0e2-7023-3800-88e2-2edf80d48360" type "application/xml" to Integration Engine... (message size: 69426 bytes, URL: " http://*************** "
13:09:59 (4076): ERROR: Finished sending to Integration Engine with error "java.net.SocketException: Software caused connection abort: socket write error". Skip confirmation and quit this loop
13:09:59 (4077): Retry mode - wait 7200 sec, 0 msec interval before retry
I tried using j2ee file adapter instead, but the channel has shown the FTP error:530.
we could login into FTP through command promt and have correct login credentials.
There is no firewall blocking.
does anyone have idea on this error? plz reply me ASAP.
Thanks..Hi
Check Read / write / delete permision for the folder in the FTP Server
Paste u r Connection parameters in the FTP
Reagrds
Srinivas -
FTP error: Receiver Communication Channel
Hello Experts,
I am getting the following FTP error in my Receiver Communication Channel.
Error occurred while connecting to FTP server: Peer certificate rejected by ChainVerifier
Please suggest.
Thanks,
AnupHi Anup,
Problem is with FTPS and not FTP.The SSL handshake needs to confirm that the FTPS client is using the FTPS server's DNS name to access the FTP service since only the DNS name of the FTPS server is stored in the certificate signed by the trusted CA (e.g. VeriSign). it's the way the Certification Authorities works.
If you are using any IP address then try with your host name.
Regards,
Madan -
Errors in Cisco Collection Manager for SCE
I installed Collection manager and I got errors in logs:
[root@sce-cm ~]# tail -f /opt/cm/cm/logs/adapter-JDBCAdapter.log
2012-05-27 22:41:32,073 [wrkr/JDBCAdapter] ERROR com.cisco.scmscm.db.DbInserter.RPT_LUR - insert err (more details in next line), tag=4042321925, fieldNo-1=13 curSqlIndex=16, i=15
java.lang.ArrayIndexOutOfBoundsException
2012-05-27 22:41:32,073 [wrkr/JDBCAdapter] ERROR com.cisco.scmscm.adapters.jdbc.JDBCAdapter - processRDR - got Throwable
java.lang.ArrayIndexOutOfBoundsException
2012-05-27 22:41:32,073 [wrkr/JDBCAdapter] ERROR com.cisco.scmscm.db.DbInserter.RPT_LUR - insert err - Exception while inserting the rdr values [0, 3, 71, 300, 300, 1338139200, 0, 1, 4, 8, 0, 0, 1], for the rdr tag = 4042321925
java.lang.ArrayIndexOutOfBoundsException
2012-05-27 22:41:32,073 [wrkr/JDBCAdapter] ERROR com.cisco.scmscm.db.DbInserter.RPT_LUR - insert err (more details in next line), tag=4042321925, fieldNo-1=13 curSqlIndex=16, i=15
java.lang.ArrayIndexOutOfBoundsException
2012-05-27 22:41:32,073 [wrkr/JDBCAdapter] ERROR com.cisco.scmscm.adapters.jdbc.JDBCAdapter - processRDR - got Throwable
java.lang.ArrayIndexOutOfBoundsException
RPT_LUR table is empty.
How can I resolve this issue?
Version is 3.7.5Hello Marat,
It seems that you might be hitting this one CSCtz20343.
Please check it.
Thanks,
Minja -
I have a website using iweb and am having problems publishing. When I try to publish it appears to be going through then stops at home page and I get an FTP error message. I talked to my website host and they checked it from their end on two brosers and it is fine. There suggestion was to contact this support group. They thought it had something to do with iweb code writing.
What version of iWeb are you using? What are you using to upload the site files to your FTP server?
I talked to my website host and they checked it from their end on two brosers and it is fine
What did they check? Have you tried viewing your site that's online to see if the changes went thru? Before you do so clear your browser's cache (Command+Option+E for Safari) and then load the site.
OT -
dreamweaver connects to server correctly, godly is showing my business catalyst site has been redirected correctly but when i access remote from dreamweaver it says there is a ftp error. How do i resolve this
Apologies
Http://www.whanaucentred.com <http://www.whanaucentred.com/>
I can access it from the web but enter the url.
When I try to upload from dreamsweaver it says ftp error even though:
-Server password and other info is set correctly in dw . and dw says it has link to the server correctly
- but When i edit site in dw and upload the changes, it says ftp error.
-When I login to businesses catalyst site on line, i can edit it from there and link to the site from there.
- when i log into godaddy it says domain is configured correctly.
Sent from my iPhone -
FTP error cannot make connection to host, ftp not working in browsers
hi
bear with me as im not webmaster, using dreamweaver mx and
today i cant up load anything just keep getting ftp error occurred
- cannont make connection to host.
so figured to was a problem with my hosts and its all fine
their end, ive tryed it in passive and not passive. And if i try to
view the ftp in a browser (ie7 and firefox) not the site but
ftp.mysite.com (im sure theres a tech name for it i dont no)
nothing is displaying, now this is only happening on my computer
and my isp(rang them they say its fine).
how to i fix this is it a dreamweaver problem a browser
problem or just some box i need to tick on my comp??
Hope you can help, will be a life saverhi
bear with me as im not webmaster, using dreamweaver mx and
today i cant up load anything just keep getting ftp error occurred
- cannont make connection to host.
so figured to was a problem with my hosts and its all fine
their end, ive tryed it in passive and not passive. And if i try to
view the ftp in a browser (ie7 and firefox) not the site but
ftp.mysite.com (im sure theres a tech name for it i dont no)
nothing is displaying, now this is only happening on my computer
and my isp(rang them they say its fine).
how to i fix this is it a dreamweaver problem a browser
problem or just some box i need to tick on my comp??
Hope you can help, will be a life saver -
Error in Cisco 2500 series Wireless Controller
I have this error in Cisco 2500 series Wireless Controller
The AP type Cisco AIR-CAP35021-A-K9
I cann't connect the client to AP when i try to connect i get this error on Cisco 2500 series Wireless Controller But the AP get ip .
Please can any on help me .
Client Excluded: MACAddress:Base Radio MAC : Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode:Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12142556/cisco-2500-series-wireless-controller -
that is...
index.html - error occurred - An FTP error occurred - cannot put index.html. Access denied. The file may not exist, or there could be a permission problem. Make sure you have proper authorization on the server and the server is properly configured.
File activity incomplete. 1 file(s) or folder(s) were not completed.
Files with errors: 1
index.html
thanks!It's under More Options triangle in the Manage Sites panel. See screenshot:
Nancy O. -
FTP Error - Mac, DW_CS6
Due to upgrading my MAC from S.Leopard to M.Lion I've lost the use of DWmx04, a programme I have used for a long time, so thought instead of going through the stress of reinstalling S.Leopard I would embrace the change. So have downloaded the trial version of DWcs6, all going well until testing the FTP. Got all the necessary FTP details for my site, but I get the message 'An FTP error occurred - cannot make connection to host. The remote host cannot be found.' I might of had a similiar problem when originally started with mx04 but can't remember how I solved it. I understand that there are many perameters, any advice would be helpful.
This might be a long shot but until very recently I was using MX04 successfully, is there anyway of transfering mysite FTP details from there?
I've checked previous posts but haven't found a definitive answer.mx04 was working on the same machine (mac pro) until the upgrade (1month ago). Due to it being a Power PC program it refuses to load, but all the databases are still on my system, will have a look at your link.
I successfully loaded mysite files into DWcs6 but it would be good if I could access my previous DW04 FTP settings, to see where and if I have made a mistake.
Thought it would be an easier way than just constantly changing and testing individual FTP settings.
Thanks -
How can I browse the tftp/ftp directory on Cisco PI 2.0?
Hi All,
I just installed Cisco PI 2.0 on a virtual appliance and I'd like to browse the tftp/ftp directory. I ssh'ed in but couldn't figure out how. With WCS running on Windows, I can easily browse those folders. Please let me know how I can browse the tftp/ftp directory on Cisco PI 2.0 to check what files are in there.
Thank you.
RobertHi Robert,
To configure tftp\ftp:
go to Configure > TFTP/FTP Servers > Add TFTP/FTP Server
To access it :
The easiest way to configure a remote FTP server would be with the steps
below:
1) Access your server via CLI and access the configuration mode:
ncs/admin# conf t
Enter configuration commands, one per line. End with CNTL/Z.
ncs/admin(config)#
2) Create an FTP repository with the commands below:
ncs/admin(config)# repository localFTP
ncs/admin(config-Repository)#
3) Setup the username, password and server address:
ncs/admin(config-Repository)# url ftp://1.1.1.1
ncs/admin(config-Repository)# user ftpAdmin password plain 12345678
ncs/admin(config-Repository)# exit
ncs/admin(config)# exit
4) Save the NCS configuration:
ncs/admin# wr mem
The use of a different partition is not officially supported as only
folders under the /localdisk partition can be read by the application.
The only supported server types include TFTP, FTP, SFTP, NFS.
TFTP\ftp contains PI backups \database backup , configbackups etc..
Thanks-
Afroz
***Ratings Encourages Contributors ***
Maybe you are looking for
-
Mail not showing messages in Time Machine
As per attached snapshot, I cannot restore any mail messages as I have no idea what they are, the subject lines, etc. are completely blank. Any ideas on how to fix this? JKB http://homepage.mac.com/dr.jkb/Sites/images/Picture.jpg
-
How do I get CS5 updated to read raw format photos
Why doesn't Photoshop read raw format photos from Nikon D600? I've tried downloading new versions of "Camera Raw". It downloads and installs successfully, but I still can't open the files in photoshop.
-
Issue updating the viewer version from V20 to V23
Hello! Our team is having an issue figuring out how to update our viewer version of our multi-issue iPad magazine. All of our issues so far have been on the Viewer Version 20, and are now wanting to use Viewer Version 23... except we can't figure out
-
Email Notification of Items Awaiting Approval
Is there any way to email the approver when a user adds an item that requires approval? I'm thinking that might be a good portlet if that functionality doesn't already exist.
-
Combining fillable pdfs leads to issue
I created a fillable pdf in Acrobat a while ago and extended features in Adobe Reader to create it. I created another fillable pdf months later the same way. And then I decided to merge the two because I needed them to be together. I highlighted both