Gnome-network-manager problems

Hello all,
I'm trying to use gnome-network-manager to connect to my wifi as it is WEP enabled and I don't know how to get it working in 'network'.
I followed this tutorial: http://wiki.archlinux.org/index.php/NetworkManager
However, when I reboot under those settings, I can't connect to anything, including ethernet.
Is there a problem in the wiki or is there a workaround that hasn't been posted there yet? I'm utterly confused as to why it will not work.
Also, if you need me to paste any code from any file, can you also tell me an easy way to copy/paste between aterm and Opera as I haven't found a way to do that yet.
Thank you very much for any help.
Matt

[matt@myhost ~]$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11g ESSID:"3KR98"
Mode:Managed Frequency:2.427 GHz Access Point: 00:18:01:E0:43:1A
Bit Rate:54 Mb/s Tx-Power=20 dBm Sensitivity=8/0
Retry limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=21/100 Signal level=-72 dBm Noise level=-87 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:76 Missed beacon:31
[matt@myhost ~]$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:0F:B0:A1:71:02
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20f:b0ff:fea1:7102/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:82717 errors:300 dropped:592 overruns:300 frame:0
TX packets:61302 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:79395572 (75.7 Mb) TX bytes:9179527 (8.7 Mb)
Interrupt:22 Base address:0x6800
eth1 Link encap:Ethernet HWaddr 00:13:CE:6A:FE:C1
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::213:ceff:fe6a:fec1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:309 errors:0 dropped:76 overruns:0 frame:0
TX packets:41 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2420181 (2.3 Mb) TX bytes:2012 (1.9 Kb)
Interrupt:23 Base address:0x4000 Memory:bc005000-bc005fff
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:232 errors:0 dropped:0 overruns:0 frame:0
TX packets:232 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:20464 (19.9 Kb) TX bytes:20464 (19.9 Kb)
ill post output of disabling gnome-net-manager in a bit (i have to reboot and save it as a file first).
also, im running fluxbox, not gnome, so could that be part of the problem? am i missing something flux specific?

Similar Messages

Gnome-network-manager & XFCE 4.4

Hey guys, someone know if gnome-network-manager also run on XFCE 4.4?
It won't run on my XFCE
Solutions to problem?
Bye,
Riccardo

Captain Spaulding wrote:
OK, open NetworkManager.conf and search for the line
<policy at_console="true">
and add this line:
<allow own="org.freedesktop.NetworkManagerInfo"/>
That, at least, should fix your initial issue. I have only just begun to learn more about dbus, so I have no clue about the second problem.
Mmmmm no entries as <policy at_console="true"> in my NetworkManager.conf....
So here we are my NetworkManager.conf:
<!DOCTYPE busconfig PUBLIC
"-//freedesktop//DTD D-BUS Bus Configuration 1.0//EN"
"http://www.freedesktop.org/standards/dbus/1.0/busconfig.dtd">
<busconfig>
<policy user="root">
<allow own="org.freedesktop.NetworkManager"/>
<allow send_destination="org.freedesktop.NetworkManager"/>
<allow send_interface="org.freedesktop.NetworkManager"/>
</policy>
<policy group="users">
<allow send_destination="org.freedesktop.NetworkManager"/>
<allow send_interface="org.freedesktop.NetworkManager"/>
</policy>
<policy user="hal">
<allow send_destination="org.freedesktop.NetworkManager"/>
<allow send_interface="org.freedesktop.NetworkManager"/>
</policy>
<policy context="default">
<deny own="org.freedesktop.NetworkManager"/>
<deny send_destination="org.freedesktop.NetworkManager"/>
<deny send_interface="org.freedesktop.NetworkManager"/>
</policy>
</busconfig>

WPA on gnome-network-manager

Hi!
I have a rather small problem. I tried to get a wireless connection by using networkmanager and the gnome-network-manager applet. It all ran fine but when I took a closer look at the applet today I saw that there's only WEP protection showing up. So I googled a little bit and recompiled the nm-applet with wpa_supplicant support. I reinstalled the package but still no WPA shows up. S can anyone help me with this, since I rather don't want to go back using unsecure WEP protection.
Thanks a lot!

gnome-keyring :< it's ugly but now works
And this made me looking like an idiot in my university today ;(
Bluman's plugin for NM isn't working too ;( I even couldn't compile it from abs
checking for a Python interpreter with version >= 2.5... python
checking for python... /usr/bin/python
checking for python version... 3.2
checking for python platform... linux2
checking for python script directory... ${prefix}/lib/python3.2/site-packages
checking for python extension module directory... ${exec_prefix}/lib/python3.2/site-packages
checking for headers required to compile python extensions... File "<string>", line 1
import sys; print sys.prefix
^
SyntaxError: invalid syntax
File "<string>", line 1
import sys; print sys.exec_prefix
^
SyntaxError: invalid syntax
not found
configure: error: Could not find Python headers
EDIT: Adding "export PYTHON=/usr/bin/python2" before "./configure" helps
Last edited by swiftgeek (2011-10-03 17:52:24)

Gnome-network-manager

Hi Everybody
I just tried to play a little with gnome-network-manager from AUR, first of all the normal network manager was missing a few files, but I managed to find them(http://aur.archlinux.org/packages/networkmanager/networkmanager/).
But when i start up gnome, it is shown fine in the Status Area, and shows all the networks, but it won't connect to any...
When connecting to an unencrypted network it says it is waiting for the network, when connecting to an encrypted network, it is waiting for the key to be verified.
My assumption is, that it is waiting for DHCP, in both cases.
If I use wifi-radar it gets an IP perfectly, also if I use dhclient or dhpcd it works fine.
Any suggestions?

I tried to use the one from testing, along with the gnome GUI from testing, but with no luck...
As you can see here, it tells me it is waiting fr the key, http://gallery.timmy.dk/Screenshots/gno … anager.png
But in the consle, iwconfig says I'm already connected...
So I'm pretty sure there something wrong with the dhcp

Xfce4 and gnome-network-manager [solved]

I just made a clean install of archlinux. installed xorg and Xfce4, xfce-goodies, gnome-panel, gnome-desktop and gnome-network-manager. also I enabled GNOME services in startup and sessions. how do I start that network manager now? is nowhere in the settings, nor there is icon to add to the taskbar (i got xfapplets installed too)
Last edited by anarxi (2009-01-14 00:22:42)

quoted from a previous thread
I solved it by uncommenting my <locale><charset> in /etc/locale.gen.
First you have to enable the locales you want being supported by your system. To enable or disable them, the file /etc/locale.gen is used. It contains every locale you can enable, and you have just to uncomment lines you want to do so.
As we want to setup an english UTF-8 conform system, we want to enable en_US.UTF-8. But for compatibility to programs that don't support UTF-8 yet, it's recommended to support any other locale, prefixed with en_US as well. Having this in mind, we enable this set of locales:
en_US.UTF8 UTF-8
en_US ISO-8859-1
After you've enabled the necessary locales, you have to run locale-gen as root to update them:
# sudo locale-gen
Generating locales...
en_US.UTF-8... done
en_US.ISO-8859-1... done
Generation complete.

Gnome Network Manager Isues

Hi Guys,
I have some weird issues with Gnome Network manager when I first boot up. I seem to have 2 profiles for my network connection enp3s0. I have a static IP for my PC, xxx.xxx.xxx.66, as I share music and photo's with a media centre PC in another room. But when I boot up or reboot the PC, it defaults to what appears to be another static IP address, xxx.xxx.xxx.109, that was used during the installation of Arch. I have disabled dhcpcd via
systemctl disable dhcpcd.service
but I can't seem to find where this weird IP is coming from.
If I open a command prompt at first login, and I issue ifconfig, my PC has the 109 IP address. If I expand on the Wired icon in Gnome's top right panel, I can see the two profiles, the incorrect one has a small dot next to it, to indicate its active. If I click on it, it disappears and my network becomes disconnected. When I reconnect, I get the correct profile with the correct IP address of 66, the 109 profile has gone.
If I go into the Weird Settings just after login, without clicking on any profiles, I have 2 settings in the box, the top one has a tick next to it and ther bottom one hasn't. If I click on the cog for the first profile, I can see it has a static of 109. Under identity, I remove the ticks for connect automatically and make available to ther users and apply. I reboot and the 109 profile is still there.
Cheers

yes, I have done it, and nothing happen
edit : I have reinstall the software, and now it is OK, tks for the help
Last edited by serafimsaudade (2007-05-20 17:34:56)

Gnome-network-manager shouldn't require Gnome?

According to its page on Gnomefiles, network-manager-applet (gnome-network-manager on Arch) doesn't need Gnome deps.
Maybe it would be a good idea to include a version that isn't compiled for Gnome in Extra, so that people using E17 or XFCE or whatever can easily use networkmanager? If people think this is practical I'll file a feature request...

Gullible Jones wrote:According to its page on Gnomefiles, network-manager-applet (gnome-network-manager on Arch) doesn't need Gnome deps.
It does need gnome deps. Requires libgnomegui and gnome-keyring... in turn it also uses gconf and other things. These can't be disabled.
James

Gnome-network-manager doesn't work at all

Hello, guys!
Gnome-network-manager starts but doesn't show its icon in Notification Area.
ps -A shows that the process is running correctly.
[sergo@myhost ~]$ ps -A |grep nm
4360 pts/2 00:00:00 nm-applet
I carefully studied all solutions listed here. My DAEMONS string is
DAEMONS=(syslog-ng !hotplug !pcmcia network netfs crond alsa sensors portmap fam dbus hal dhcdbd networkmanager networkmanager-dispatcher @cups gdm)
Please help.

yes, I have done it, and nothing happen
edit : I have reinstall the software, and now it is OK, tks for the help
Last edited by serafimsaudade (2007-05-20 17:34:56)

Gnome file manager problem

lately I've noticed that in the Gnome file manager when I go to a directory with images in it, 4 will show up and all the rest don't and the cursor is in a waiting mode that it can't get out of.
What causes this and how can it correct it?
Last edited by vinoman2 (2009-11-07 15:00:38)

Thanks, I later rebooted and that fixed the problem. It was only in one directory.
I just moved a image to a folder and it did it again. I ran nautilus in the terminal and it only opened nautilus.
Is this a bug in Gnome? It seems to happen every time I want to move an image into a folder.
Is there a way to fix this?
Last edited by vinoman2 (2009-11-07 15:02:37)

Dbus/hal/gnome-volume-manager problem

I've got hal and dbus running but it doesnt even seem that gnome-volume-manager is started. I added it to my gnome session but that didnt seem to do the trick. I'm trying to be able to just plug in my usb key and ipod and have them automount. It works if I restart hal or run gnome-volume-manager from the command line but then work work again unless I restart that stuff again. Here is a cut from my fstab:
/dev/sda1 /mnt/usb auto user,noauto 0 0
/dev/sda2 /mnt/ipod auto user,noauto 0 0

Hi lhoerste,
I had this problem with automount as well. The way I fixed it was adding
dbus hal to daemons line in /etc/rc.conf. You probably did this already.
Next, when you are in the gnome desktop, stick in a cd. Nothing happens right?
Now go to preferences=>removable drives and media (I think this is what it is called. I'm not sitting infront of my computer at the moment). Then make sure that the checkboxes pertaining to "mount automatically" are checked.
Close window.
Now your cd should automount and appear on the desktop. Eject the cd by right clicking on the icon and choosing eject.
Now, restart and ***make sure you save settings*** before leaving.
Get back into the gnome desktop and plug your cd back in. It should automount now.
This is how I got automount to work for me.

[Solved] Can't get gnome network manager running

Alright this one is a head scratcher. I've folowed the wiki for network manager to a T except I can't get the network manager icon to show up (I have notification addon already running). I don't have any network loss though.
Here's my rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="localtime"
USEDIRECTISA="no"
TIMEZONE="Canada/Pacific"
KEYMAP="dvorak/dvorak"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(powernow-k8 cpufreq_ondemand cpufreq_powersave forcedeth snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="myhost"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="dhcp"
INTERFACES=(lo !eth0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng !network netfs crond laptop-mode dhcdbd networkmanager @alsa @hal @fam @gdm)
Last edited by dr/owned (2009-01-09 05:16:43)

I assume you're running nm-applet --sm-disable once you get a window manager session up?
Try starting networkmanager after hal. From the wiki:
You must also "disable" the default network daemon, and add the hal, dhcdbd and networkmanager daemons in this order:
DAEMONS=( ... !network hal dhcdbd networkmanager ... )

Network manager Problem

I installed the Network Manager, but regardless which button i click when i want to open network access manager / firewall / ethernet i get the following error in IE:
Error in NMI : Application is disabled. This application is not allowed to run on this system. This has been disabled by the Administrator.
Can someone tell me where to enable this?

I installed the Network Manager, but regardless which button i click when i want to open network access manager / firewall / ethernet i get the following error in IE:
Error in NMI : Application is disabled. This application is not allowed to run on this system. This has been disabled by the Administrator.
Can someone tell me where to enable this?

Network manager problems

Hi!
I have got some problem, just installed arch following the unofficial guide for newbies [or sonething like that^^], installed gdm and gnome-shell.
Now i cant get my Networkmanager to connect me with a wireless lan network.
If i dont add networkmanager to the demons and let network there and connect with
sudo wpa_supplicant -B -Dwext -i wlan0 -c /etc/wpa_supplicant.conf
sudo dhcpcd wlan0
everything works!
Can anybody help me?
Pls tell me which output u need so u can help me, i am new to all of this!
thx in advance!

daemon.log:
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmClient: disposing /org/gnome/SessionManager/Client2
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmStore: emitting removed for /org/gnome/SessionManager/Client2
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmManager: Client removed: /org/gnome/SessionManager/Client2
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmManager: last client disconnected - exiting
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmManager: ending phase EXIT
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): Unreffing manager
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmManager: disposing manager
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmStore: Clearing object store
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmStore: Unreffing object: 0x1a25870
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmStore: Unreffing object: 0x1a25950
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmStore: emitting removed for /org/gnome/SessionManager/App2
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmStore: emitting removed for /org/gnome/SessionManager/App1
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmStore: Clearing object store
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmStore: Clearing object store
Nov 18 11:02:17 localhost gdm-simple-slave[796]: WARNING: Child process 894 was already dead.
Nov 18 11:02:17 localhost gnome-session[894]: DEBUG(+): GsmStore: Clearing object store
Nov 18 11:02:17 localhost gdm-simple-slave[796]: WARNING: Child process 894 was already dead.
Nov 18 10:02:19 localhost rtkit-daemon[966]: Successfully made thread 1088 of process 1088 (/usr/bin/pulseaudio) owned by '1000' high priority at nic$
Nov 18 10:02:19 localhost rtkit-daemon[966]: Supervising 4 threads of 2 processes of 2 users.
Nov 18 11:02:19 localhost dbus[723]: [system] Activating service name='org.freedesktop.ColorManager' (using servicehelper)
Nov 18 11:02:19 localhost dbus[723]: [system] Successfully activated service 'org.freedesktop.ColorManager'
Nov 18 10:02:20 localhost rtkit-daemon[966]: Successfully made thread 1121 of process 1121 (/usr/bin/pulseaudio) owned by '1000' high priority at nic$
Nov 18 10:02:20 localhost rtkit-daemon[966]: Supervising 5 threads of 3 processes of 2 users.
Nov 18 11:02:20 localhost dbus[723]: [system] Activating service name='org.freedesktop.UDisks' (using servicehelper)
Nov 18 11:02:21 localhost dbus[723]: [system] Successfully activated service 'org.freedesktop.UDisks'
Nov 18 11:02:24 localhost goa[1155]: goa-daemon version 3.2.1 starting [main.c:112, main()]
Nov 18 11:02:51 localhost dbus[723]: [system] Failed to activate service 'org.freedesktop.Avahi': timed out
these are the last few lines....
what do the mean? anything in there that indicates my problem? wonder, any idea?

Network(Manager) problems after messing with netctl

Hello, and thanks for taking time helping me!
The story so far:
I was trying to bridge my wired and wireless network on my laptop, using netctl: https://wiki.archlinux.org/index.php/Bridge_with_netctl
It dind't worked and it messed my network up (I could see the wifi-indicator in the topright of my screen frozen in its "connecting" state), but I could still use wifi.
So I removed netctl and deleted its files from /etc/netctl and disabled/stopped the zombie-bridge. And then I could not connect wireless anymore (wired still works altough still frozen in the "connecting" state according to Gnome).
My system:
PC: An Acer aspire v3 laptop
OS: Arch x86_64
DE: Gnome-Shell
using NetworkManager as a.... NetworkManager I
the bridge I was trying to make:
Description="Example Bridge connection"
Interface=br0
Connection=bridge
BindsToInterfaces=(wlp3s0 enp2s0f0)
IP=dhcp
some logs (# systemctl status NetworkManager):
Sep 11 17:15:16 Skynet NetworkManager[299]: <info> Activation (wlp3s0) Stage 3 of 5 (IP Configure Start) started...
Sep 11 17:15:16 Skynet NetworkManager[299]: <info> (wlp3s0): device state change: config -> ip-config (reason 'none') [50 70 0]
Sep 11 17:15:16 Skynet NetworkManager[299]: <info> Activation (wlp3s0) Beginning DHCPv4 transaction (timeout in 45 seconds)
Sep 11 17:15:16 Skynet NetworkManager[299]: <info> dhcpcd started with pid 1415
Sep 11 17:15:16 Skynet NetworkManager[299]: <info> Activation (wlp3s0) Stage 3 of 5 (IP Configure Start) complete.
Sep 11 17:15:16 Skynet NetworkManager[299]: <info> (wlp3s0): DHCPv4 client pid 1415 exited with status 0
Sep 11 17:15:16 Skynet NetworkManager[299]: <info> Activation (wlp3s0) Stage 4 of 5 (IPv4 Configure Timeout) scheduled...
Sep 11 17:15:16 Skynet NetworkManager[299]: <info> Activation (wlp3s0) Stage 4 of 5 (IPv4 Configure Timeout) started...
Sep 11 17:15:16 Skynet NetworkManager[299]: <info> Activation (wlp3s0) Stage 4 of 5 (IPv4 Configure Timeout) complete.
Sep 11 17:15:16 Skynet NetworkManager[299]: dhcpcd[1415]: sending commands to master dhcpcd process
Sep 11 17:15:22 Skynet NetworkManager[299]: <info> Activation (wlp3s0) Stage 4 of 5 (IPv6 Configure Timeout) started...
Sep 11 17:15:22 Skynet NetworkManager[299]: <info> (wlp3s0): device state change: ip-config -> failed (reason 'ip-config-unavailable') [70 120 5]
Sep 11 17:15:22 Skynet NetworkManager[299]: <info> NetworkManager state is now DISCONNECTED
Sep 11 17:15:22 Skynet NetworkManager[299]: <info> Disabling autoconnect for connection 'Starfleet'.
Sep 11 17:15:22 Skynet NetworkManager[299]: <warn> Activation (wlp3s0) failed for connection 'Starfleet'
Sep 11 17:15:22 Skynet NetworkManager[299]: <info> Activation (wlp3s0) Stage 4 of 5 (IPv6 Configure Timeout) complete.
Sep 11 17:15:22 Skynet NetworkManager[299]: <info> (wlp3s0): device state change: failed -> disconnected (reason 'none') [120 30 0]
Sep 11 17:15:22 Skynet NetworkManager[299]: <info> (wlp3s0): deactivating device (reason 'none') [0]
Sep 11 17:15:22 Skynet NetworkManager[299]: <warn> Connection disconnected (reason -3)
Sep 11 17:15:22 Skynet NetworkManager[299]: <info> (wlp3s0): supplicant interface state: completed -> disconnected
My guess is that somewhere my bridge messed everything up. But as I've leared with arch the awser could be very simple.
Thanks Again,
Pascal

I think I know what the problem is. I saw that a deamon called dhcpcd@wlp3S0 was running at the same time NetworkManager was. This would mean that both Networkmanager and netctl where running at the same time. I've disabled "dhcpcd@wlp3s0" and........ nothing.
Does anyone knows witch daemons i should disable/enable to let the system run on networkmanager alone?

Gnome Network Manager under Fluxbox

Hello! Im using fluxbox and I had wifi-radar to connect wifi but I missed a lot the gnome networkmanager so I've removed wifi-radar and installed it.
Now Im getting mad because, after following all the steps the networkmanager starts correctly but says there are no network devices and I cant solve this.
Some info
ifconfig:
eth1 Link encap:Ethernet HWaddr 00:13:02:13:BC:DD
inet addr:192.168.1.35 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::213:2ff:fe13:bcdd/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1306 errors:0 dropped:4620 overruns:0 frame:0
TX packets:1215 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:871040 (850.6 Kb) TX bytes:258880 (252.8 Kb)
Interrupt:19 Base address:0xc000 Memory:d0100000-d0100fff
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:400 (400.0 b) TX bytes:400 (400.0 b)
iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11g ESSID:"WLAN_0A"
Mode:Managed Frequency:2.462 GHz Access Point: 00:01:38:6C:DA:1D
Bit Rate:54 Mb/s Tx-Power:15 dBm
Retry limit:15 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=86/100 Signal level=-47 dBm Noise level=-47 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:4620 Missed beacon:0
and /etc/rc.conf:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="es_ES.utf8"
HARDWARECLOCK="localtime"
USEDIRECTISA="no"
TIMEZONE="Europe/Madrid"
KEYMAP="es"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(b44 mii ipw3945 iwl3945 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-al
loc snd-pcm snd-timer snd snd-hda-intel soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="Nosferatu"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
eth0="dhcp"
INTERFACES=(lo !eth0 !eth1)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng !network dhcdbd networkmanager netfs crond ipw3945d)
Someone knows what's going on?
Thank You!

wonder wrote:i mean add hal to DAEMON list.
DAEMONS=(syslog-ng !network hal dhcdbd networkmanager netfs crond ipw3945d)
Yeaaaaah! Now its working!!
I added the daemon.
Thank you very much!

Gnome-network-manager problems

Similar Messages

Maybe you are looking for