Help, blank monitor on New PC build with NX8400GS-TD series

Hello,
I am having a problem with my new computer build:
Mainboard : MSI X48C Platinum
CPU:Intel Core 2 Quad Q9550
PSU: Ultra 650 Watt Atx power supply
Memory : 4 Gig DDR3PC3-8500
HDD: 500 Gig WD Caviar SE16 ATA 7200/16MB/SATA-3G
Video Card: NX8400GS-TD Series
DVD Drive: LG 22X DVDRW SATA OEM (L49-1028 OEM )
The problem is that when I turn on my computer it powers on but I am getting a blank screen on my monitor. I have tried removing all devices (HD, DVD Drive) and leave the barebones, but it still does nothing. I know that the monitor that I am using is good because I tried it on a different computer and it works. can anyone please help me out?
Thanks

Quote
There is no way to check the video card without using another video card
Exactly (unless you have have a diagnostic/P.O.S.T. Status PCI Card which will show you each P.O.S.T. Checkpoint that is successfully passed). You could, of course, also test the card in another system.
Quote
How do I know if it posts without being able to see the screen?
Usually, you don't. That is what makes trouble-shooting so hard sometimes.
Quote
you said to take the video card out to see if it posts, how do i know if it posts if i can't see anything?
You have misunderstood what I was saying. During the Power-On-Self Test, the initialization of the output devices happens rather late in the test cycle.
You decribed this behaviour earlier:
Quote
ok, i am making backward progress now. before i got it to power up by:
1) turning on power on psu and then
2) pressing the power button on the computer case
Now it doesn't even power on and it tries to power up when I only:
1) try turning on the power on the psu
When I do the above the fans spin for a second then nothing.
These symptoms do not really indicate the video card. If you remove the card and the same symptoms occur, you can more or less be sure that these problems are not caused by the card as such. You do not need to see anything on the screen to be able to oberve the power-on behaviour of the systems.
Quote
It can't be the following:
CMOS (I cleared it multiple times)
Shorting of the case (I took it out of the case)
CPU (I checked the CPU Pins and it is fine)
Well, then there is other stuff left to check:
Quote
- forgotten CMOS Clear (while the main A/C power cable is unplugged from your PSU)
- shorting issue inside the case
- a problematic or failing PSU (or: not all power connectors hooked up properly)
- broken or bent CPU Socket Pins
- memory problems
- a bad/damaged motherboard (either DOA (damaged during shipping), damaged during handling/installing (electrostatic discharges, damaged by a short circuit inside the case) etc.)
- and yes, a bad video card (but this is not very likely in my opinion) ---> If it was the video card, the system should turn on and stay on (the P.O.S.T. should stop during output device initialization) ---> So, this is easy to check: Test without the video card. If the system shows the same on/off behaviour, it is not the card causing this)

Similar Messages

Report Builder with multiple data series

I am not able to figure out how to create a bar chart using
multiple data series in the Report Builder. I can do it with
explicit CFML coding but not in the Report Builder. I am running MX
version 7 with the current (as of 9/1/07) download of the Report
Builder.
My table contains visit information by site, with standard
demographics on each visit (age, race, gender, etc.) I am trying to
analyze the data by site, for example, race by site.
I am using an SQL statement to sort and group by site &
race. I can get a chart of the number of visits for each site or
the total number of visits by race across all sites. But I can't
get race by site. The SQL statement looks like this:
SELECT race, site, COUNT(*) as counter
FROM visit_info WHERE userid = #session.uid#
GROUP BY site, race ORDER by site, race
Every variation I have tried for showing race by site either
leaves out part of the results or creates a bar chart that has the
race and site categories as separate entities (White, Black,
Chinese, Site1, Site2, Site3, etc). I've also tried creating a
combined variable (site_race) but that doesn't seem to fare any
better.
Any help would be appreciated.

Pop,
Badunit's example is one possible arrangement that you might have described; that is, one column for X values and several columns for Y values. This is the case when you should respond that you are sharing X-values. With all the data in one table, you can select it all at once, so you don't have the problem with dragging additional series into the chart.
The Numbers User Guide PDF's first chapter is the place to start getting your bearings - you will learn how to distinguish Header vs. Body rows and columns. It's worth the effort to take another look at it.
Since you are using a Scatter Chart, it's important not to use a header column for X because X values must be Numeric, as opposed to Text.
Jerry

Help needed for a new Mac user with his photo and video librarys

after swopping my Ericson for an iphone a year ago. then taking delivery of an iPad on launch day. I have finally taken the plunge and swopped my windows pc for a lovely 27" iMac... what have I been doing all these years using windows? using the Mac is a joy.
As I get more involved with their products I am constantly fascinated (and frustrated) by Apples way of doing things. this situation is no exception and I need Apple people with Apple experience to help me make a decision.　
I am looking at software to organise my photos and videos. I have approximately 7000 photos residing on a windows home server. in addition to that there are some 200 or so HD videos taken with either my Sanyo Xacti camcorder or Sony DSC W300 camera. both cameras I think produce MPEG format
my first experience was iPhoto. great for the `price' but not very flexible. single libraries, poor editing facilities. and because I have files referenced and not copied to my iPhoto library, if I deleted from the library its not deleted from the server (and vice versa). this leads to images being displayed in the library that don't exist etc.
then I downloaded the Aperture 3 trial. great until I came across the `Unsupported file format' situation with the MPEG videos that strangely enough, iPhoto will recognise and play (the Apple way of doing things).
1. should I put the photos on the Mac instead of the server?
2. Is there a better way of managing the images for deletions etc
3. should I stick with Aperture because of the editing
4. is there a better software or way of managing the videos
sorry for the ramble but its all new to me

had a good session on all three of the recommended programs and now have a better understanding of the excellent advice I have been given.
iPhoto
great `free' program that is easy to use but somewhat limited on features. think I would always be looking to upgrade from here (feels a bit boring)
Aperture
really enjoyed using this but at £170! a hefty price tag considering its limited file support. fortunately its only my camera video clips (MPEG) that it wont view. my camcorder files (MP4) are fine so this is looking better as a one stop solution.
Elements
much more than just a image touch up. considering what it can do.. very good value at around £60. teamed with iPhoto it becomes even more attractive.
My issue still remains with the masters file location.
I would prefer to keep all my media on the external server to ensure I have a fail safe recovery option. its a 4TB 5 disk affair which contains all the family music, video images and DVD's etc (likely to change to a Mac server in the future!)
one feature that I cant find, (even in Aperture which surprises me), is the ability to automatically manage deletions from referenced locations? i.e. delete a file from the server and when aperture opens up the thumbnails are updated. or, delete a referenced master in Aperture and an option comes up to delete the referenced file on the external drive.
how would a professional photographer or studio using Aperture manage this process (or would they use something else?)
forgot to mention that through our student facilities i can get a discounted copy of Photoshop CS5 for around £175 which is close to Aperture. is this a worthwhile option or overkill
Message was edited by: buttons129

New Computer Build with Windows 7 Adobe Flash Player won't install freezes with empty black box

I have just build a new windows 7 computer and every time I try to install adobe flash player, after clicking the install button, it goes to an empty black adobe box and freezes. I have tried changing settings in IE, but I can't figure it out. Will someone please help me.
KD

Does it appear to be the same as my issue on win8.1?:
Empty installer dialog on Windows 8.1

I am unable to use the new retinal display with the 600 series smart board

I am a teacher and have both an older macbookpro (2006 2gigs ram 10.7) and the new retinal display macbookpro (10.8.2). My school had two versions of smartboards (one is the 685 with a UX60 projector; the other is a newer 800 series). My older macbookpro works with both boards but my new macbookpro works only with the newer 800 series. It does not show any display at all with the older boards. I have tried reducing the resolution but that does not help. I have taken it to apple and it checks out fine. I have spent hours with smartboard support in Calgary. They can't figure it out but have never used a Mac with a retinal display and the older board or the UX60. Any suggestions?
Thanks,
Ed S

You should also ask this in the MacBook Pro forum. This is the forum for the 13” white and black plastic MacBooks that were discontinued in 2010. You should also post this question there to increase your chances of getting an answer.
https://discussions.apple.com/community/notebooks/macbook_pro

Convert a scatter graph with multiple data series into individual graphs

I am trying to convert a scatter graph with multiple data series into individual graphs, with the series having the same formatting as in the graph when all series are together.
Normally, if I delete any series, the color scheme for all the other series vanishes. I can then waste more time in having to re-adjust the color and shape of the series, but this is tedious. This, I do not want. Is there an automated way to do this?
Ideally, of course, all series would appear in little subsections in the space of the former one graph, all with individual axes, but I can't have all, so I'll settle with having several individual new graphs, each with just one series, and with the original
formatting.
Thx.

How about creating a copy of the chart, and then setting all series except one to be transparent (no line, no marker)? Repeat for each series.
Regards, Hans Vogelaar (http://www.eileenslounge.com)

Have mac mini with thunderbolt monitor 1yr old, recently updated with new 10.0.2 from apple, now iMovie doesn't seem to support my Sony HDR-XR500 camera. Is there any help on this?

Have mac mini with thunderbolt monitor 1yr old, recently updated with new 10.0.2 from apple, now iMovie doesn't seem to support my Sony HDR-XR500 camera. Is there any help on this?

haha, so now i'm thinking. I'm learning the terminal as fast as i can but there are several lines of codes and commands in there that throws up red flags to me that i don't fully understand. It just looks fishy too me. It would be highly appreciated if someone could just check this out just to tell me that i don't need to worry about it. Or point me in the right direction. I just feel un easy about this. ha.

New build with big bang x-power board. Any help welcome and appreciated.

Started new build with big bang x-power board, i7 960 processor, 3 x 4gb mushkin cl7 ram and imation m-class 128gb solid state drive running Windows 7 ultimate x64. This particular SSD is probably just temporary. Since I don't have the SSD I really want (yet) and this 1 was given to me at no cost, by a friend who really hated it, I thought it would suit my current needs. The specs & reviews were not encouraging, but they were not exactly "terrible" either.
Anyway, I was unable to install the OS on the Imation drive, while connected to a sata2 port. Got repeat bsod despite many variations in settings, including fail safe defaults. After clearing cmos and switching to a sata3 port, I got it to install no problem after putting settings back to cpu voltge: 1.35, dram voltage: 1.65, mode: AHCI and all others: default with only 1 RAM module seated.
So... I think this may be a BIOS issue and was hoping someone could point me to the most recent BIOS version available for me to update my BBXP board. I believe v1.6 is what i'm looking for, unless my info is outdated. Since my plan is ultimately to run the OS from an SSD using a sata2 port, I definitely want to resolve this, and hopefully any other issues with the v1.0 BIOS that I just haven't encountered yet.

Thanks again HU16E, and sorry for any confusion and/or lack of information. I'm guess you can tell i'm still new at this, but I'll try to do better with specifics in the future -please forgive me.
SSD = Solid State Drive. The brand of this particular solid state drive is "Imation" and the series is "M-Class." It is a sataII device that would not install the OS while connected to any of the sataII ports on the board. Initial attempt was made with all settings on auto. When that didn't work, I adjusted voltages because it seemes unstable with repeat freezes and restarts. The install seemed to start ok with adjusted voltages but still would not complete.
I then moved the sataII drive to a sataIII (marvell) port, put all settings back on auto and the install went further (loaded files, copied files, expanded files, etc) but would froze several times during windows start up attempt. I then changed cpu & dram voltages back to the adjusted values I tried when the drive was connected to the sataII port and everything worked fine. Tested under load for 4 hours and no problems of any kind. Its still working now. I do however suspect I will have many more problems when I move the solid state back to a sataII port, or when I add my other Hard Disk Drives.
BIOS version showed: 1.0.0 but i can check again to assure I didn't misread anything in my haste. If i'm mistaken, I will post the correction. Hope I answered everything the way you wanted & didn't just make matters worse and more confusing lol. thanks for the link as well, i'll check on it asap

Help!! adding new pages to doc with logo!!!

I've posted various questions for a couple hours now, none are answered. Is everyone sleeping or does no one know how to use Pages?? I'm near tears and I've read the manual about 10 times and don't understand it. I've tried to Google it but I'm not even sure what exactly to Google.
I have an 18 page document in Pages. It's just a plain old word processing document. A list of Gluten Free restaurants in my area. I add new restaurants to this list all the time so it needs to re-order itself as it does as a plain word processing document.
I want to brand it more so I'm putting my logo and a little design in the bottom left corner of each page, or at least thats how I'd like it to look.
So I set up page one, saved it as a template, captured it, done everything I can think of. But when I copy the document and paste it into the text boxt on the first page of the new document with the little logo on the page, all the subsequent pages do NOT have that logo on them. Just the first page.
IF I set up 18 pages with the logo, and then paste it just adds 17 blank pages after that first page with the logo. And those 17 pages that I set up prior to pasting are after the pages it added after the paste that have no logo.
How do it get this to add a page with the logo in the corner??
So when I add 5 new restaurants and it has to add a page to fit them it it will have that logo. This can't be that hard to do. I need the doucment to automatically add new pages when text is add and those pages need to have the logo,
Please help me!!!
Susan

I'm sorry you think that Peter and it isn't true. Maybe you are testy because its 2 am.
I spent hours trying to figure it out on my own. I looked all over these forums, I Googled it, I went to other Apple tips and forums I am familar with, went thru the manual. I tried a lot of places first so I really don't think I'm demanding and I'm sorry if I came off that way.
I was just super frustrated. Not being very computer savvy can be super frustrating, often I find what I "think" might be the answer for something I'm looking for and I can't even understand the answer. I try, I follow the steps but some of the terms I don't know and then have to google and follow more steps and blah blah.
I'm sorry but I didn't just come here without doing research first for the answer, so its not fair to say I expected others to do the work for me. I did try. I agree the information here us beyond useful, I never could have done anything without out in the past, I've used it many times. But you can shoot the messenger if you want but the response time does seem slower. Not sure why you take that personally.
I'm sorry to **** you off so much.

NO LINE!!! NO HELP! NO DUCTING NEW BUILD HOUSE

So here goes . , my ongoing unlimited stress with bt
27 july ordered bt
closest visit? 23 august!!!!! WHAT A JOKE
wait till 23th bt was suppose to turn up between 1-6pm noone turned up noone called to say they wasnt turn up.
called them up for them to tell me there was a fault in my line? i dont even have a line connected!!!
they also tell me i didnt need someone to come out because the work inside the house was complete and all they had to do with flick a so called switch in the exchange! but yet they booked a appointment and it took them over 4 weeks for them to notice this even after i told them it was a new build with all new fitted bt installed inside and going outside the house into the ground!more wasted time and hassle!
got told it will be connected within 24 hours and i have to wait till 8pm on the friday before calling back , so i ask what time does call centre close friday , get told 10pm ok i said if not connected by 8.01 i will call back after being hung up on and sent to 3 different people i got that so come 8pm friday no connection no line so i call bt back ( ON A MOBILE!!) and what the heck there closed FALSE INFORMATION AGAIN
come saturday i call them again to be passed from pillow to post spending over 3 hours on the phone to them!!!!!
i eventually get through to a manager who tells me the builders need to confirm they have installed the ''' duct'''' so called outside the house. this one manager was the one i spoke to on friday who said he would call me on satursday at 11am. which he never called, in fact he never bothered to call untill come near on 5pm after being on hold and on the phone for over 3 half hours he come through from someone transfereing him as he was the manager on call that day, little to say he was very shocked to have caught me yet again!!!!, where he then went into what his job was and it wasnt stretching to deal with me or my issue as he is very busy! being the manager of not doin the jobs he says i assume!!!!
right so heres a problem i can solve our builders are still building new propertys close to mine so i contact them and approach and they confirm all the work is done, so i relay this back to bt who tell me the order is now goin through and will up and running within 24 hours.
so i then have to wait untill tuesday because of the bank holiday , yet again more calling more transfering here there and everywhere hours and hours pass on the phone
i get back in touch with another manager who tells me that the line will be connected as soon as he has contacted open reach to get someone to turn the line on! wooohoo i think where getting some where
NOOOOO i then recieve another call telling me open reach cant do any work on the line or any work without the builders contacting them , eve though i have already confirmed it with all of them
come friday 31st september i receive a call saying the builders have confirmed the work and the work will be carried out and i should be connected very soon,
no connection as of monday so i call for a update...
get through to another person who has took all my details but has no idea what is going on and just telling me they understand how im feeling!!!!. who then passes me from manager to manager then to faults, then to accounting then finally to contracts! the guy didnt know who i was why i was put through but got through to open reach who told them the line would be connected working via wednesday ...
wednesday comes and yet again there is no connection no line NOTHING,
i call back up yet again ON A MOBILE to find now that no work will be done no work has been done!
they have no idea who called me to tell me the builders had confirmed it and no idea about the line other than it will not be connected without confirmation from the builders on ducting..
the finall words for the call was that i had to wait another '''24 HOURS''' For an update on open reach connecting the line , his words was just 24 hours for us to get the update and i promise you we will know more
someone is suppose to be calling me back from never land that never calls so i wont hold my breath.
i have NEVER in all my life been messed about by any company as bad as bt has let me down, i cannot trust anything im being told as they keep saying then taking it back and changing it, all i get is im so sorry i understand or, well i dont know why they have told you that or i cant see that or anything like that!..
im at the end of my wit patience and sanity, please if someone can get my line connected please help because im at a right loss with no phone and appointments and calls i need to make
thank you

Hi misscheryl1987,
Did you get my email on the 14th?
When I spoke with the engineers' department originally, they confirmed that work would start on the 28/09 but may take up to Monday 01/10 for the line to activate, depending on the amount of work required.
At the moment I am unable to get more updates but I will chase up on Monday when the department I need to speak to is open again.
Stephanie
Stephanie
BTCare Community Manager
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post. If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

New build with MSI 970A-G45 won't load OS or live CD

Motherboard: MSI 970A-G45 AM3+ AMD 970
CPU: AMD Athlon II X3 455 Rana 3.3 Ghz Socket AM3
RAM: G.Skill Sniper Series 2x4GB DDR3 1866, Model F3-14900CL9D-8GBSR
Video Card (original): ASUS ENGTX550 TI DC/DI/1GD5 GeForce GTX 550 Ti
Video Card (operational): XFX 7600 GT
System HD: Runcore 64GB Sata II SSD
Optical Drive: LITE-ON SATA DVD-RW drive
I just finished building a new upgrade build into an existing case with an existing PSU and hard drives/optical drive. Originally the system wouldn't power on at all, which I traced to the new video card (something to do with grounding or an inadequate power supply maybe?), but in any case I got past that for the moment with my old video card. The system will power on and get to the BIOS screen. I can enter the BIOS and everything looks fine: all my drives are detected, the RAM is present, the CPU looks correct. However, when I go to actually load an operating system, it never loads. After the BIOS screen I just get a blank screen with a white blinking cursor in the upper-left corner, and this never goes away (I've tried leaving it for 10 minutes or more).
Originally I was trying to boot from the mentioned SSD which has both Ubuntu 11.04 and Windows 7 64-bit partitions installed with GRUB2 to load them. This didn't load, so I tried an Ubuntu 11.04 live CD in my DVD-ROM drive. That didn't work, so I tried the same CD in an external USB CD-ROM drive in case it was a problem with the SATA controller/connectors. Still the same behavior. So I tried a memtest86+ CD in both drives. Still the same behavior. For each of the tests after the first I explicitly opened the boot menu with F11 at the BIOS screen and selected the device I wanted to try.
At this point I've already tried exchanging the memory I had originally bought with the memory I listed above, since the old memory I realized after I bought it was labelled as "Intel i5/i7 compatible" and the new memory is on the MSI support list for this motherboard model. Any thoughts on where to go next? My next thought was to RMA the motherboard but I feel like I'm flying blind here. I've never see a new build get stuck at this point in the boot process.

OK posting from Ubuntu on my now-working build!!
So, after two weeks of messing around with the CPU, RAM, video card, etc., I finally have the thought that the one thing I haven't tried yet is the old SATA expansion PCI card that I put in early on at the bottom of the motherboard underneath the video card (out of direct sight, out of mind apparently), for when I try to connect all 7 of my SATA devices. I tried pulling that out - presto, it boots. Retried a couple of times for proof, keeps booting correctly. It can even load memtest86+ off a CD. Put the PCI card back in - still boots. Reconnected the sata drive - no boot. Remembered that this particular PCI card has two SATA ports and one is for RAID of some kind, tried the other port - now it boots. The drive connected to the card is also detected by the OS.
In conclusion, it was something entirely different from what I was working on, as it usually is.
I'm going to get to work connecting everything back up, getting the new video card working, etc. I suspect I'll be back at least to read when I try to get my memory working at 1866 (different forum I know). Thanks to those who responded for the pointers.

I have a new MacBook Air with a USB super drive. I put in the DVD and I get nothing. No icon on the desk top and DVD player is no help. How do I play a DVD or eject the one in now?

I have a new MacBook Air with a USB super drive. I put in a DVD and I get nothing. No Icon on the desk top, no help from DVD player. How do I get it to play and how to eject it now that it's in?

There's a defect. The computer is in warranty so take it in for repair.

Is there a phone number to call Adobe. I go around an endless loop pressing their contact info tabs? Maybe someone at this sight can help. I am new to digital photo - I have been a B&W film photographer for many years. I have a problem with a Macbook Ai

Is there a phone number to call Adobe. I go around an endless loop pressing their contact info tabs? Maybe someone at this sight can help. I am new to digital photo - I have been a B&W film photographer for many years. I have a problem with a Macbook Air. It was working fine - I was using LR and a message came on the screen that said something like the memory was dangerously low. I stopped and tried to delete LR files. I couldn't do it. I closed the program and tried reopening and got the message that there is not enough memory available to open LR. I contacted Apple. They spent a half hour on the phone with me and eventually told me they didn't know how to help. The tech said that LR had gobbled up all the memory and said I should contact Adobe and ask where and how my photo files are stored and to delete them. I have several back-ups. Thanks - Arthur

This sort of error message only comes up for Lightroom when your hard disk is full. Indeed this has nothing to do with internal memory as that will be intelligently be dealt with. If you have a mac Book Air that is not so surprising as the cheapest versions come with very small hard disks and if you shoot raw with any recent camera, you'll fill up your hard disk very quickly and you can probably only store a few months of pictures if you are a typical photographer. So the bottom line is that you need to create some room on your hard disk. You should move some of your originals to an external hard disk. You can also delete some of your backup copies of your catalog file that Lightroom automatically generates every few days and that quickly gobble up hard disk space. So first figure out how full your hard disk is. To see that, go to the apple menu, hit -> About this Mac -> More info->Storage. You should see your internal hard disk on top and you'll find that it is almost entirely full with photos. Now find your Lightroom catalog file using Finder. It is usually in a folder in the Pictures folder in your home directory. You should see a Lightroom 5 Catalog.lrcat file, a previews file and a folder called backups. Inside the backups folder, you'll find a lot of subfolders. They have names that show the dates the backups were created. If you have backups of your entire hard disk, you can delete these backups when they are older than a few months. I usually only keep the last 4 around. Just drag the folders into the trash can on the dock on the bottom of your screen and empty the trash. This will probably free up enough space that Lightroom will already run again. Now start thinking about where you will want to store older images. If you have a good USB3 or Thunderbolt hard disk that is probably the best option. There is a video here by Adobe that has some instructions on how to do this: Is Your Hard Drive Full? Here’s How to Move Images to Another Drive in Lightroom. « Julieanne Kost's Blog If that doesn't work because you don't have enough hard drive space to run Lightroom yet, here is another set of instructions to move your files using the finder to the other hard disk: How do I move only my photos to another hard drive, leaving the catalog where it is? - The Lightroom Queen. If you follow that, as soon as you confirm all your images are on the new hard disk, you can delete them from your internal one. She is not so clear about that part but if you don't delete the originals that you moved off you don't free up space. You should move the folder structure over to the new hard disk and then reconnect the folders in Lightroom. That should make it refind all your images.
That said, if you are uncomfortable with the computer in itself, your best bet is to find a local photography club. There is invariably a Lightroom savvy person in there that could help you move your files. That might be your best bet if you are uncomfortable moving these yourself. A general mac savvy person like you would find at an Apple store or so generally will not be able to help you with this except when they are photographers themselves and know Lightroom. You might get lucky with that.

My Ipod was originally set up as a sub-account of a firends. After that, I got an Iphone and set up my own Apple account. I just got a new Ipod, and now can't sync my old Itunes to it. Can anyone help me? I'm even OK with deleting the old Itunes account

My Ipod was originally set up as a sub-account of a firends. After that, I got an Iphone and set up my own Apple account. I just got a new Ipod, and now can't sync my old Itunes to it. Can anyone help me? I'm even OK with deleting the old Itunes account, and staring over. I just really want to get the new Ipod under my own account, and be able to use it...

There is no such thing as a "sub-account." Also, you probably mean iTunes library, when you say "account." Your "account" in iTunes is your Apple ID, which is what you use to sign in to the iTunes Store to make purchases. iPods are associated with an iTunes library, not with an Apple ID (iTunes Store account). You'll need to clarify...
So, this is what I think you are saying. You previously shared an iTunes library on a computer with your friend. Your old iPod was synced to that iTunes library.
You got an iPhone, and at that time, you set up your own iTunes library. Is that on a different computer? How does the iPhone affect your question about the iPod?
You got a new iPod. What is your "old iTunes"? Is that the iTunes library you shared with your friend?

Failed to Install The New Preview Build. Installation Failure: Windows failed to install the following update with error 0x80246007: FBL_AWESOME1501 9926 Professional.

Hello,
I'm having issues upgrading my Windows 10 Technical Preview installation build 9879 to a newer build that's become available late January 23rd.
I am installing the new upgrade in a Hyper-V virtual machine and get the following error:
Failed to install the new preview build, please try again later. 0x80246007
What could be the problem?
Previously I've had messages that Windows cannot be upgraded on a computer with less than 2 Gbyte of RAM. That's a Hyper-V VM with dynamic memory and I was highly surprised to see this error; never had this before. Had to set 2048 Mbytes as a minimum memory
for this VM. Now that I have this 80246007 error code.
When looking up System log, the following error messages are listed multiple times:
Installation Failure: Windows failed to install the following update with error 0x80246007: FBL_AWESOME1501 9926 Professional.
The errors are returned for the Event ID 20 by WindowsUpdateClient
in task category Windows Update Agent..
I reviewed the HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WindowsSelfHost\Applicability
registry key as suggested in Windows
Insider stuck on build 9841 - "No new preview build was found", and here is what it shows:
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WindowsSelfHost\Applicability]
"BranchName"="fbl_awesome1501"
"ThresholdRiskLevel"="low"
"ThresholdOptedin"=dword:00000001
Note, when attempting to install the downloaded update from a native boot, installation starts with no errors.
However, since setup is not supported for a natively booted VHD files, it does not proceed further showing a message that installation on virtual drives is not supported.
Looks like Setup is having problems installing in a Hyper-V virtual machine.
Possibly, some ESD files got corrupted during downloading? Is it possible to remove them and re-download missing files? (I, however, noticed that Windows seems to re-download upgrade files after you restart 9879 and attempt to check for a new build.
Any clue why installing under VM causes 9926 to fail?
Thank you in advance.
Well this is the world we live in And these are the hands we're given...

Hi,
According to the error message, this problem seems like update package installation failed during system upgrade.
You can try to remove ESD file which locate at boot of C drive and upgrade the system again for test.
On the other hand, make sure the system 9879 installed all Windows pushed updates before system upgrade.
Roger Lu
TechNet Community Support

**Help, blank monitor on New PC build with NX8400GS-TD series**

Similar Messages

Maybe you are looking for

Help, blank monitor on New PC build with NX8400GS-TD series