Help for Sharp Edges

Yesterday afternoon, I went to the Apple Store to try the new Macbook.
The screen is gorgeous, crisp, colorful and clear and a vastly welcomed improvement to the iBook's pale and difficult to read screen. Adjusting brightness levels may help reduce any glare or eyestrain problems.
The keyboard, with its reduced padding, feels like it was designed for stylish looks and not especially for long-term comfort. A workaround might be to reduce typing pressure and also to add an external keyboard for home use.
The palm rests are another story. They're an ergonomic catastrophe. The edges of the Macbook are so sharp that using the trackpad for a short while quickly induced pain in my hand.
Can anyone suggest ways to reduce edge pressure and sharpness and make an otherwise great laptop less ergonomically lethal to my palm and wrist? Thank you.

I understand what you're saying. However, from an ergonomic standpoint, it really is not good for you to rest youre palms on the 'palmrests' at all. The best thing you can do for your wrists and the tendons and musculature of your hands is to have straight, neutral wrists so that your fingers fall down on the keys from your knuckles onward while you type. Also, rather than rest your palms on the palmrest when you use the trackpad, try moving your whole arm from the shoulder. I also suspect that your table is too high since the edge is cutting into your wrists.
Resting your hands on the palmrests or using a laptop on a table that is too high is recipe for RSI in the long-term. So maybe the sharp edges may be a blessing in disguise! Seriously, I've learned the hard way.

Similar Messages

  • Solution for sharp edges on Retina MacBook Pro

    The sharp edges on the front of my new Retina MacBook Pro (late 2013) drove me crazy cutting into my wrists.
    My solution is two pieces of self sticking velcro - the loop kind of velcro which is soft. Apply them across the top and down the front edge on either side of the trackpad all the way out to the side edges. They are not too thick so as to prevent sleep when closing the cover. They don't look too bad either. I'd say they match the black keys on the keyboad.

    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
    Step 1
    Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
    View ▹ Show Log List
    from the menu bar.
    Enter the name of the crashed application or process (Finder) in the Filter text field. Select the messages from the time of the last crash, if any. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message (command-V).
    When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
    Please do not indiscriminately dump thousands of lines from the log into this discussion.
    Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
    Step 2
    In the Console window, look under User Diagnostic Reports for crash reports related to the crashed process. The report name starts with the name of the process, and ends with ".crash". Select the most recent report and post the entire contents — again, the text, not a screenshot. In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.) Please don’t post shutdownStall, spin, or hang logs — they're very long and not helpful.

  • G5, 10.6.8, trying to print biz cards, instead of clear print with sharp edges I get fuzzy print with pixels showing. Saving as PDF doesn't help. Any solution?

    G5, 10.6.8, trying to print biz cards, instead of clear print with sharp edges I get fuzzy print with pixels showing. Saving as PDF doesn't help. Any solution?

    Mac OS X Version 10.6.8, iMac12,1
    .cwk (Appleworks)
    Kodak Easyshare 5100
    If I paste the jpeg on a draw page and shrink it to fit, fuzzy print. If I create the text directly on a draw page, it's fine. (That suggests to me the problem isn't in the printer.) But I want to include a small drawing on the card, and the pasted jpeg of that small drawing is very poor quality.

  • Sharp edges

    Hi,
    I've used my PB 15" DL since November and have worked out most of the software problems I've had but here is something I wonder what people think of: There are some almost sharp edges on this machine (and probably others of the same design). In particular, if you press the delete key so that your finger is on the edge towards the right, you feel the almost sharp edge of the top plate brush against your finger. This same thing happens with almost any key as well. Try the keys on the left and you'll see the same thing.
    The trackpad. Its edges are smooth but borderline sharp. The clicker has a sharp edge on my machine on its left side.
    How about the hinge for the screen?! Quite sharp.
    How about the hole where the latch for the screen goes in? Sharp. (And that's not even counting the two pointy things on either side of the top of the screen and the latch itself.)
    Some keys don't respond as smoothly as others, I get the overall impression that while this is a very stylish machine, some corners were cut and the end result is not as "polished", literally, as it should be.
    One other place that is disappointing: The battery compartment door. It isn't flush, it jiggles when you poke your finger at it and the worst part is the gasket that runs around it is already starting to fall apart! The compartment door has that same sharp edge that you can find all over this machine.
    I tend to rub my fingers in these places to sort of temp them to hurt me or to dull them but they shouldn't exist at all. Bad design I'd say. (And there should be, maybe there is, a thread on the illegibility of the keyboard letters and the symbols on the sides. Grey letters/symbols on a grey case are hard to read. It's beautiful but a case of bad design winning over functionality.)
    Cheers,
    John L

    I had the keyboard replaced a little while ago (to try to fix another problem mentioned in this thread, amongst others: http://discussions.apple.com/thread.jspa?threadID=584197&tstart=0) and I now realize that typing is so much easier without having to notice (worry about) the sharp edges.
    It is a whole new experience for me on this machine. I had used my Powerbook Firewire for a little while while the new one was being repaired and I was going to say that keyboard felt so much more comfortable, responsive but now this one is better so I have no complaint anymore.
    I was serious by the way. You all were no help with your sarcastic replies.
    Cheers,
    John L

  • Sharp edges on MacBook Pro

    What chances are there of Apple changing it's sharp edge design on future Mac Book Pros? I've just returned a 13" MacBook Pro because the front edges are so sharp they left red marks on the the sides of my hands hurt after 2 hours of typing with the laptop on my lap. I know it's probably not the case if on table, but I often need to have my laptop in lap! (Which is what it's designed to do) - as I travel a lot with it. I'm a devoted Mac user - just love them - and I'm hugely disappointed by this but i't just not comfortable. I've just got a refund and will carry on with my original 1st Generation MacBook Pro (which is a great machine (lacking the specs of course) and very comfortable to use - until Mac come out with a kinder-on-the-wrists version. My partner's just got one and has the same issue and will return it. We're just hoping Mac will alter this at some point with upcoming models.

    Welcome to Apple Discussions!
    There have been numerous complaints about the sharp edges, and the best thing to do is to give feedback to Apple as sig suggests.
    There is something known as a computer glove that might help should you need a new Mac before Apple gets around to changing the design.
    http://www.amazon.com/s/?ie=UTF8&keywords=computer+glove&tag=googhydr-20&index=a ps&hvadid=4307637227&ref=pdsl_5zwpyolgute
    Office Depot carries these if you want to look at one in person.
    Good luck!

  • Developing Online Help for Mobile Applications

    My company is just starting to develop applications for mobile devices (cell phone, iPad
    , etc.). Can anyone tell me whether RoboHelp is the best Adobe application for devel
    oping online help for mobile devices or if some other application should be used? Thanks.

    Thanks for the insight. I haven't read about RH8 so wasn't aware of that difference. No, I haven't tried the demo yet. I guess that would be the logical next step. I've been trying to get to the STC web site to download the PDF file of the presentation, but can't get the web site to open. Oh well. Thanks again.
    Regards, Fred W. Brown
    Technical Writer 3
    InnovaSystems International, LLC
    (757) 282-7921
    • Writing is simple. First you have to make sure you have plenty of paper... sharp pencils... typewriter ribbon. Then put your belly up to the desk... roll a sheet of paper into the typewriter... and stare at it until beads of blood appear on your forehead.
    • Prof. Cosmo Fishhawk, in Shoe

  • Sharp edges on the mac book

    I have owned 10+ macs and i am disappointed that my new mac book is giving me deep red marks from the sharp edges. Any suggestions on adding an accessory to stop by red, painful marks?

    Grade of sandpaper? Heck, I dunno. I just grabbed what I had at the house. Pretty fine grade, though.
    How much did I remove? I don't know that either. I just kept at until it felt smooth. Don't make it difficult. You just use common sense. You won't even see the difference, you FEEL the difference.
    For that reason, no photos.

  • Ipod Touch 2nd generation Sharp edges on bottom

    Hi all,
    I love, love my 2nd generation ipod touch. As recent college graduate I used it everyday and everywhere. My question is... has anyone else experienced sharp edges alongside the bottom of the dock charger? When I constantly hold the ipod touch in my right hand, vertically, my right hand pinky finger constantly gets rubbed up against the dock charger underneath the bottom of the ipod touch. It has always been an issue, but I am not one to complain.
    Has anyone else experienced this problem?
    Thanks.
    Message was edited by: Schaefer25

    Not Charge
    - See:      
    iPod touch: Hardware troubleshooting
    - Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar                          
    Also:
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar                              

  • Freetalk HD camera for Sharp 830E

    Hi,
    I've just bought  Freetalk Conference HD camera (at In Store Shop) dedicated for Sharp TVs. I uploaded the newest TV software for Skype connections and ...voice connection work perfect, but unfortunately I can't use video mode. I can see " camera off" on the TV screen. The blue lamp on the camera is on, which means the camera is ready to work.
    In addition camera serial # in recognized and shown in skype settings. Does anybody can help me to solve this problem? Thanks

    I am having the same exact issue with a Freetalk HD webcam that is suppose to be compatable with my Panasonic Blu Ray player. The Freetalk, Panasonic, and Skype technical support teams all have punted on the issue so hopefully someone will step up and figure this out.

  • Remote Code for Sharp

    Can anyone please help, I had my youview box installed I need the code for my Sharp tv  LC40LE511E K.

    Thanks for your help, forget to say that I have tried all the codes for Sharp on the http://bt.custhelp.com/ci/fattach/get/2306219/1330618726/redirect/1 page, none worked. I had the same problem with The Sky box I have to send them the TV model and they got me the code. Was told by the Sky engineer that it is not a genuie Sharpe.

  • MacBook Design (sharp edges)

    I have just bought my MacBook. I have be using it for two weeks approximately, but now my wrists are hurting me to much. Apparently my MacBook edges, specially those where my wrists lay down, are very sharp and hurts me. For my comfort I'm actually using a piece of cloth beneath my hands to ease the pain.
    I don't know if there is a solution to this problem, beside the cloth and maybe a sandpaper.
    Do anyone else have experienced this problem too?

    What if I'm actually just resting my palms on it? I do type fairly "properly", e.g. hands raised, wrists not touching anything.
    The sharp edges become an issue if I'm I'm just reading a page of text, and occasionally hit the space bar to advance the page. Surely no need for my hands to "hover"...
    However, in the few weeks I've had my 'book I've somehow adapted to the edges and they no longer seem to bother me. It's mostly unconscious adjustments to keep the same spots on my palm/wrist from resting in the edges, as well as taking my hands entirely away from the computer.

  • Remote control code for Sharp LC-32DV200E

    Hi there!
    i have just tried all codes for Sharp from BT Vision help page and it does not work. My telly is less than a year old, so it can't be an issue of old telly. Does anyone know any other codes (apart from those on |BT Vision list in help)? I will greatly appreciate some help here. Thanks in advance.

    Yankee2 wrote:
    Bought a new rev'8' sky remote control as the old one has hard-to-push buttons.  I followed the instructions for programming the remote to my tv (LG 32LC2DB) but the codes supplied do not work on new remote.  Checked code on 'old' remote (0206) and tried that - no luck.  Red light does not blink when holding down 'select' and 'red button'.  Switched everything off, removed batteries, turned back on and still nothing.  New remote does work all Sky controls but not tv.  Any suggestions would be appreciated. Try these codes as well 1293  1206.Then try the procedue below.Press TV (one flash)Hold select and red till remote flashes twice999SelectTVSelect and red till two flashesEnter codeSelect

  • Tell me the secret to sharp edges.

    Hi guys,
    How do i get a sharp edge each and every time.  I am using the rounded rectangle tool to draw some tabs.  At one time it gives me sharp edges and some other time the edges are blurred.  An example HERE
    Why is that so.  What is the secret to sharp edges all the time.
    Thanks for your response.
    am

    Am...
    Please read through the thread linked just below. The answers posted by Buko and Zeno are on the mark, but I took a little more time explaining what's causing the fuzzy borders you're seeing and why the "Snap To Pixels" option fixes it.
    "Strange border on shape and other layers"
    http://forums.adobe.com/message/1648285#1648285

  • Creating search help for a field in AdHoc Query

    Hi
    We have created an infoset based on LDB PCH.
    (The infoset contains object type O only).
    For the object-id field the users want search help when choosing this field for selection.
    Using "start via selection screen" does not give a good solution.
    Can anyone explain how I can create search help for fields in an infoset?
    Regards
    Kirsten

    Hi
    We have created an infoset based on LDB PCH.
    (The infoset contains object type O only).
    For the object-id field the users want search help when choosing this field for selection.
    Using "start via selection screen" does not give a good solution.
    Can anyone explain how I can create search help for fields in an infoset?
    Regards
    Kirsten

  • Need to restrict values in F4 help for Batch Characteristic

    Hi,
    I need to restrict values in F4 Help for a batch characteristic based on values entered for another characteristic. I could not find any BADI or Exit for this purpose. There is a BADI CACL_VALUE which is triggered after an entry is selected from dropdown list but nothing when we press F4. I thought of using Object Dependency but I need to write a programming logic for the requirement. Please let me know if there is any way to write program in Object Dependency or any other way for this requirement.
    Regards,
    Nikhil

    Hi nikhil simha,
    first of all, find out which search help is called.
    [Hierarchy of the Search Help Call|http://help.sap.com/saphelp_nw70/helpdata/en/0b/32e9b798da11d295b800a0c929b3c3/frameset.htm]
    may help you.
    If you know the search help, you may enhance it, but first of all you should check the where-used-list and make sure that the search help shows the requested behavior only in the context where you want it to.
    If it is your own program, you may be better off to create your own search help and define the triggering fields as search help interface input fields. Then you can use the values to filter results.
    Regards
    Clemens

Maybe you are looking for

  • Cannot launch Camera Raw in PSE 8

    I have PSE 8 with the Camera Raw 6.2 plug-in. The program works perfect exept that I cannot launch the Camera Raw converter. When I open a RAW-file in the editor or via the organizer, then the file just opens in the Editor mode. No raw converter... I

  • Creating Foreign tables

    Hi Everyone, What is Foreign table? Can any one of you please tell me how to create foreign table, please suggest me with an example. Helpful answers will be rewarded immediately. Thanks & Regards, Venkat.

  • Media Manager Flexview Sync - Upload Failure - Mac Lion

    I am having difficulty with Media Manager on a Mac with Lion. Syncing to the Flex View Library either stops as soon as it starts, or stops part way through the upload. This happens even if I upload just one photo. When syncing starts, the progress ba

  • I use to open in safari now it open in  YTD yarhoo dont like lost all my set up things can i ring for help aus

    ok sorry       have had apple desk top just over a year down loaded some thing now it will not open in safari goes to   yarhoo  dont know how to delet any thing from screen  or delite any thin g

  • Deployment error - Missing class: javax.servlet.jsp.jstl.core.Config

    Hi, We are using JDeveloper 10.1.3.0.4(SU5) on windows for development of ADF application. We need to deploy the developed application onto Oracle Application Server 10g (10.1.3) which is running on Solaris. We are using BC4J, WAR and EAR deployment