Help me find the required Wireless Access point

Dear Friends,
I am in search of a access point with below specification, so please let me know that which model has this functionalities.
. Wireless Access Point:
* No of port should be 10Base-T/100Base-TX Ethernet
* Standard should be IEEE 802.11g, IEEE802.11b, IEEE 802.3, IEEE 802.3u, IEEE 802.3af(PoE), 802.1q(VLAN) , 802.1X(Security authentication), 802.11i ready (Security WPA2), 802.11e ready (wireless QoS), 802.11F(Wireless roaming)
* LEDs should be power, PoE, Wireless, Ethernet
* Web Management should be built-in web user interface for easy browser-based configuration (HTTP/HTTPS)
* SNMP Support should be SNMP version 1, 2c, 3
* Operation modes should be access point made, point to point bridge mode, point to point multipoint bridge mode, repeater mode
* External antennas should be 2 (omni directional) SMA detachable
* Security should be WEP 64-bit/128-bit, WPA-PSK, WPA2-PSK, WPA-ENT, WPA2-ENT
* Access Control should be wireless connection control: MAC-based
* Wireless Security monitor should be Intrusion alarms(e.g. rogue client detected, spoofed MAC address) Denial-of-service alarms (e.g. duration attack, association table full) vulnerability alarms (e.g. access point is not using encryption, access point is broadcasting SSID)
* Power should be 12V 1A DC input, and IEEE 802.3af compliant PoE. Maximum power draw should be 3.36W

Hello Shekib,
All you did was describe the WAP200.
It fully fits in your description.
Please check it and see with your eyes.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps10047/ps10048/data_sheet_c78-501966.html
I hope i helped you.
Regards.
Andrey Cassemiro.

Similar Messages

Apple TV 2G (Airplay and Homesharing) can only stream from devices on the same wireless access point range??

connection:
40 Mbps Fiber Broadband connection using:
Devices:
1. Main Modem/router (AP1): Huawei HG8245 (provided by ISP) - Wireless enabled.
2. Remote Access point (AP2): Linksys/Cisco E3200 Wireless gigabyte router flashed with DD-WRT v24-sp2 (06/14/11) mini (Cascaded -wired- LAN to LAN from main modem).
3. Wireless Repeater to cover a dead spot (AP3): Linksys/Cisco E1000 wireless repeater.
4. Apple Tv (AT2G) with home sharing/airplay enabled.
5.( Ipad) with home sharing on itunes enabled.
6. Win7 (PC) using iTunes with Home sharing enabled.
all devices are updated to their latest firmware.
In order to cover a large 3 story house with Wifi. I had (AP1) is located on the first floor, while (AP2) is located in the basement floor directly wired by LAN to LAN with (AP1). (AP3) is located on the Ground floor away from the living room to repeat wireless network into the back yard. While (AT2G) is located in the living room on the ground floor right in the middle of both (AP1) + (AP2) while connected via Wifi.
Network SSID, security, passphrase and wireless settings of (AP2) are identical to (AP1) to create a single big LAN/WLAN roaming network where all devices connected to both wireless access points can find/share the others. As understood, it's refered to as bridging.
I have noticed that my iphone/ipad does not show the airplay button anywhere within the wireless network. it seems that the apple TV randomly choses to connect to the AP with stronger signal, or switch to the other in case of a reboot to one of them.
to elaborate further, if i was sitting in the living room (groundfloor), trying to airplay some you tube contents via Wifi to my Apple TV, i may not find the airplay button available all the time, i found out the reason is while i'm wirelessly connected to AP1, the Apple TV was connected to AP2 and both deviced cannot detect each others to enable my purpose. that goes the same for Home Sharing. only if my Ipad/PC and Apple Tv are on the same wireless AP. they would detect each others immediately.
although, the second AP (AP2) is suppose to extend my wireless network of the same subnet in which any device connected can be found.
After all sorts of trial and error tweaking my router/access point, I thought the problem would be due to the Linksys 3200 capability of bridging WLAN and lacks few protocols that enables my purpose. i have flashed the firmware to a DD-WRT, but again, problem was not solved.
I have not tried having my Apple Tv wired to either router/AP, but i assume it may work well if i do so. i still need to solve this wireless connection issue though.
Am i the only one with this problem, would there be something wrong with my setup?
Your feedback is highly appreciated.

You may or may not already have your network set up correctly, it's just that I can't tell from what you have said.
I have a main router provided by my ISP, I have several other Airport Extremes and Airport expresses connected by Ethernet, all set up to bridge the network created by the main router.
Each maker has their own settings, but bridging should be reasonably obvious. In simple terms my main router distributes IP addresses to all devices, the Airports bridge that network by passing these addresses to the devices from the main router. A base station that isn't in bridging mode will distribute its own addresses to the devices connected to it.
I don't really follow your next point.
instruction for configuration vary from manufacturer to manufacturer, the best course of action here is to refer to the manual. If everything is set up properly the addresses of everything on your network will have identical sets of numbers for the first 3 of 4 groups of numbers that make up an address, the last set must always be different. I think the part you are referring to with your DD-WRT is the option to have Ethernet and wifi bridged or not.
Some routers may be easier to configure than others, but generally speaking they should all work with the Apple TV. 5Ghz is less likely to suffer interference but it is much more likely to be blocked by solid objects, it may or may not be an advantage.

IOS 6.0.1 - Problems with certificate based authentication on wireless access point

Hi all
We are using iPad 2 as order terminals in our shops for about 5 months. Some of the iPads (the first who entered the field) started to cause problems now. These iPads are no longer able to keep long-term connection to the wireless access point in our stores. After selecting the SSID a successful authentication using the stored EAP-TLS certificate is performed (this can be seen in the log files of our wireless controller and by the IP adress that is given by DHCP). But within seconds the affected iPads opening up a captive portal page (empty, without contents) and separates the connection to the SSID after a short time again.
Affected are currently only iPads 2 with iOS 6.0.1, which were staged about 5 months ago. The newer devices with iOS 6.1+ connect without problems and open no captive portal page. The first cases occurred on the last Wednesday. Before that everything worked without difficulty. No modifications took place on the security structure. The numbers of affected devices increased until all iOS 6.0.1 were affected.
Access to other SSIDs (without use of certificates, by entering a key) for the devices is still possible (the devices does not open an captive portal page). The DHCP scope is not used up, so there are enough IP addresses available.
"Newer iPads" with an iOS of 6.1+ are are showing no problems on the same wireless access point, where the older devices are rejected. New and old devices use the same certificates and authentication mechanisms.
In the analysis of the issue, it turned out that the problem can be solved by an update to iOS 6.1.3. Subsequently, the iPads will be able to rebuild a connection with the access point, without a captive portal page.
Since the bandwidth is very narrow dimensioned in our stores, the communication of the iPads was severely restricted. Thus, the iPads are for exampleare accessible for the APNS but can not find iOS updates or check for their availability.
A comprehensive update to iOS 6.1.3 is currently excluded.
Does anyone knows this issue? What else can be done (except from updating)?

I will answer my own question in case it helps anyone else.
It would "seem" the ios 6 devices try the proxy and if that is not working they resort to the def gateway.
To Fix I did the following:
Brocade WIFI network has IPS and Advanced Firewall rules that seemed to be tthwarting some traffic, the iphones would then try the default gateway and be blocked at the FW.
I disabled the IPS and the Advanced Firewall Settings on the wifi as they are redundant to our main IPS and firewall that all traffic flows through anyway. I will tune it later, but when the CEO is demanding a fix "**** the security, full speed ahead"
Created some rues on the firewall to allow...
- IMAP-SSL (port993) outbound
- SMTPS (port 465) to yahoo servers outbound
- tcp port 587 to yahoo servers outbound
- https to akamai servers
Most http and https goes through the proxy as it should, BUT...
It seems that the akamai traffic allways ignores the wifi proxy settings and just heads straight for the default gateway. I suspect there is a bug in the icloud app?
Hope this helps someone else.
-Bo

AirPort Extreme used as a wired/wireless access point at same time?

Can the gigabit ethernet ports (wired connection) on the AirPort Extreme be used at the same time as the wireless-N connection when it is installed to a switch on an existing network as an access point? Will it still broadcast simultaneous Wireless-N dual band signals?
If both are yes, then do you have any other information regarding the cofiguration? Or helpful links that may help me? Thank You.

I have not yet purchased an airport extreme or even tried this. I have an existing network with a simultaneous wireless-N dual band router feeding a main switch. From the main switch I have cat5e wired gigabit connections to 4 PC's then two cat5e cables, each going to a small switch at seperate media centers.
I have one area that I have a single cat5e wire that can not get the wireless signal from the existing router. In addition to the wireless signal problem, I could use a couple extra gigabit ethernet connections to this same area, but can't pull any new cat5's to it.
I was told I needed to install a multi-gigabit-port wireless-N access point or install another switch with a single port wireless-N access point connected to it. As I looked into this, the dedicated wireless-N access points are wireless-N dual band but do not broadcast them simultaneously (it's either/or).
So I was wondering if I would benefit in any way by using the AirPort Extreme instead of the dedicated wireless access point recommended, and if it will give me what I need plus a simultaneous dual band wireless-N connection to the area? I don't know why the IT didn't recommend installing another router like I'm thinking? Don't know if it will even work? If it is a good idea or not? Don't want any conflict or networking problems to have to deal with just because I didn't listen and/or got the wrong item? What do you think?

Where can i find the french manual for the Procurve MSM310 Access Point

Hi
I'm looking for the french version of the ProCurve MSM310 Access Point manual.
Where can i find it ?
Thanks in advance
David

Hi, David:
You may want to post your queston on the HP Business Support forum -- MSM Series.
http://h30499.www3.hp.com/t5/MSM-Series/bd-p/wireless-e-series-forum#.U-fngDh0zGg

Using the Aiport Express as a Wireless Access Point on Windows XP

I would like to use my airport express as a wireless access point so that it will connect wirelessly to my router and via an Ethernet cable to my laptop that does not have a wireless card. Also, I have a laptop that I don't have admin rights to, so I can't install the airport express software. I do have another computer in which I am able to set things up on, but ultimately I would like to use the Ethernet port on the airport express as a DHCP device that once configured it will automatically connect to my laptop even after powering off and on any machine with DHCP. I believe that this can be done - but correct me if I am wrong.
So far, I have been able to get the airport express to connect to my router, but I can't seem to get the intenet connection on my laptop. Can someone help? Does the software have to be installed to work even after it is configured?
Thanks!

I have successfully gotten my AX to connect to my wireless router via the wireless client mode, but I can't seem to get the network connection to come out the either net jack of the AX.
Unfortunately, the wireless client mode will not activate the Ethernet port. The purpose of this mode is to connect to an existing wireless network as a client (just like any other device connecting to the network) and be able to either/or stream iTunes or share a USB printer.
The only mode where the Ethernet port is enabled, would be to configure the AX as either a relay or remote base station in a Wireless Distribution System (WDS). But, unfortunately, your Belkin wireless router may not be WDS-compatible with the AirPorts.
Again, the only Belkin routers, that I'm aware of that are compatible are the F5D7230-4 & F5D7130.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

Is it possible to remove the iphone history of wireless access points to which you've connected?

So.... I work in a place where there is a lot of security and snooping. There are folks specifically assigned to track down phones in unauthorized places. Their enthusiasm is sometimes annoying.
I leave my phone in a locker outside of the restricted area. However, I recently overheard some of the "snoops" discussing a phone that they had found. They were discussing a specific wireless access point that was in that phone's history, that caused some discussion. Although the phone was located in the locker area, they had apparently discovered it and examined it.
It was my phone.
One obvious course of action is to make sure the phone is always turned off (which I will do), but they have now identified my phone by the APs to which I connect, and I'd like to erase that history.
Is it possible?
Thank you.

Settings > General > Reset > Reset Network Settings.

How to find out wireless access point?

Hi all!
I want to write one simple program which could detect all wireless access point're running around me. So pls somebody could tell me what I have to do now?
Thank you so much!

Dear prometheuzz !
I knew it but :) OS default can't detect AP which not
broadcast SSID. By the way why U said that Java is
not suitable for this task???Dear viethanguyen ,
Java doesnt have this functionality, cause Java is a High Level language, and what you are asking for is low level programming that is related to the underlying OS system calls and modules. So if your OS doesnt have/support this functionality, then how you expect Java to have it!. And if you are using GNU/Linux search for tools like kismet, air-snort ...etc.
Amr M. Kamel

Please help me find the error in the annex VI,access

Hello, everyone, this is a program about ACCESS, please help me find the error in the annex VI, why do I always run time error. Thank you very much.
Attachments:
write access test.vi ‏22 KB

Thank you for your reply, I have an attachment process map, could you help me change it, I just want to put my number in the array can continue to update the database. And I want to create a table.
this is my msn :[email protected]
Waiting for your reply on line
谢谢你的回复，我的附件中有程序图，能不能帮我改一下，我只是希望，把我的数组中的数能够持续的更新在数据库中。并且创建一个我想要的表。

Need help to find the "leading point size"

Hi,
I need help to find the "leading point size".
Any para style leading is more than 2 points of my font size, I need the alert message "Its more than 2 points for your font size". For instance my para font size is 10 here my leading should be 12 points rather than its 14 points, I need the alert message.
Is this possible by script?
by
hasvi

Hi Hasvi,
Try this.
var doc = app.activeDocument;
var texts = doc.stories.everyItem().textStyleRanges.everyItem().getElements();
var pstyle = "Following paragraph styles have more leadings:\r\r";
for(var i=0;i<texts.length;i++)
    var ps = texts[i].pointSize;
    if(texts[i].leading > ps + 2)
        pstyle += texts[i].appliedParagraphStyle.name;
alert(pstyle)
If it is correct than mark the answer as correct and don't mark your question as correct answer.
Regards,
Chinna

How can I get alerts if a Wireless Access Point has been disconneted from the network?

How can I get alerts if a Wireless Access Point has been disconneted from the network?
Is it possible to get alerts via email from the WLC or WCS if Access-Point has been removed from the network?
Thanks in advance.

Hi,
The below link will answer ur question!!
http://www.cisco.com/en/US/docs/wireless/wcs/7.0/configuration/guide/7_0event.html#wp1229996
Please dont forget to rate the usefull posts!!
Regards
Surendra

How do you remove a manually configured wireless access point on the iphone 4S?

I have manually configured my iPhone 4s to point to a wireless access point that I no longer use. How do I delete it from the list of access points on my iPhone?

You can only "Forget this Network" while actually connected to the network, so ignore iamjeremi's post. Other than restoring your phone as a new device, you can't if you cannot connect to the network anymore.

Beginner Needs Help with Aironet 1131G Wireless Access Point

I have a new Cisco Aironet 1131G Wireless Access point. It is picking up an IP address and I can ping that address. However, I can't access it via the web-based GUI or the CLI. I have preformed the reset. Any suggestions would be greatly appreciated.
Thanks.

Hi,
I cannot access means what?? are you not able to go to CONFIG T prompt from CLI?? and if you are in the same subnet as that of the AP, are you not able to open up the GUI?? if you are not able to then, issue the command "show version" on the AP CLI and see if your image is "RCVKW8" image. if so u need to convert the same to IOS using the below method..
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap22-trouble.html#wp1038660
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

Set up time capsule as wireless access point

I am trying to set up my old apple time capsule as a wireless access point for my girlfriend. She is at college and the university does not permit routers, so I am trying to set the time capsule up so that is just takes the hardwired internet and allows wireless access to the internet so she can use her iPad and MacBook Air on the wireless instead of having to use a gigabit adapter to use the ethernet. The time capsule has the newest firmware and she is running mavericks which has the newest airport utility software. However I am not sure what settings to use to make this work. I am fairly intelligent when it comes to computers however I am not very skilled in networking. If anyone can help I would greatly appreciate it.
Thank you in advance!

How old is the Time Capsule? Running what firmware?
You have a problem.. If you cannot use the TC in router mode, then you are going to have to use it in bridge.. and it then depends on if the Uni system will hand out mulitple IP addresses. .which I doubt. In the end you might be stuck.. and it is not possible really with any system..
Bridge normally requires that the TC take an IP address and then clients connecting to the TC wireless will also get IP addresses.. but if the uni system only hands out one address then the TC has already captured it and there are no more available.. but try that method first.. as it is the easiest.
If it fails there is a more complicated method.. where we can give the TC a separate static IP in a different IP range and the wireless will still be bridged.. so the MBA or the ipad can use the wireless.. but only one can ever be online at a time.
The only way around this is to use the TC as a router contra the rules in the uni.. although I would suggest the uni only cares if you break their system. Most people don't.. but I am unsure what happens if you do.
Ask their IT people how to use a wireless only device like ipad, when they only provide ethernet. You might find there already is a wireless internet system as well.

Help me find the required Wireless Access point

Similar Messages

Maybe you are looking for