Help with installing hp envy 700-214 pc series drivers

hi i just reformatted my pc and now i can't use it becuase the drivers are unavaible everywhere. hp use to have the windows 7 drivers for my pc on their webpage and took it down... which makes no sense..? my pc has no internet connectivity. i would download the drivers on my laptop and plug in a flash drive transfer them over and then plug my flash drive into my pc and download each driver that way. can anybody help me? will this be the last HP product i ever own..? i need drivers for windows 7 ultimate 64 bit.

Hi: Unfortunately, the support pages are not working for most of the newer HP PC's. It has been that way for about a day now. Since I am not employed by nor do I represent HP, I am not sure when they will have the pages working again. Check back again some other time. With the Independence Day holiday weekend in the USA, I would not expect this to be taken care of immediately.

Similar Messages

HP Envy 700-214 Fails to install windows 10

Earlier this Year, I purchased an HP Envy 700-214 PC 64 bit, with Windows 8.1 that also provided a recovery partition. I have tried to upgrade to Windows 10, from the Windows Upgrade process, which failed 3 times. I then used the Media Creation Tool to download the 64bit iso from Microsoft, when I then burned to a DVD as an image. From my running 8.1, I accessed the DVD drive and ran the setup.exe. It ran through the who initial process of downloading updates and checking the PC for problems and space, It then gave me the options to upgrade and save my personal data. I then clicked on Install, which ran until about 25% completed. I then received a message that the install failed, without a hint of why it failed. I am just about ready to give up and stick with 8.1, as I have never seen such a mis-managed software process as this upgrade in my entire life.....

Hello, Have you used any third party partitioning/cloning software to change partitions sizes or installed an SSD and used partitioning software to clone the OEM factory image to the SSD? The Win 10 upgrade may fail if this is true. On another note the following article by Ed Bott may provide a solution. We know you must upgrade first to tie your device to an activation code so you can install Win 10 on the device again. Ed Bott provides a method for installing Win 10 cleanly that also activates during the installation process. Note, your current Win 8.1 install must be properly activated in order for Win 10 to activate properly. Try setting UEFI (BIOS) settings to defaults before attempting the clean install procedure described by Ed Bott in the above article. Have a recovery option available if this fails. This method is going to require installation of all software you have installed now on Win 8.1. You will be nuking Win 8.1 and starting fresh with Win 10. If it fails you will have to reimage Win 8.1 using a Microsoft Recovery Drive and a good system image stored on external backup drive, third party backup software, or use HP recovery discs to go back to the factory image. Backup the SWSETUP folder on current Win 8.1 installation to use to install HP software on Win 10. You also have Win 10 drivers at your PC's software and driver download site available if you have any driver issues after the Win 10 upgrade completes. Lastly, are you using a wireless keyboard or mouse? If so, try the upgrade or the clean install method (per Ed Bott) using wired peripherals. I have not seen any tips on this but it might help by limiting complexity. Did you run the compatibility checker tool included in the" Get Windows"notification program located near the system clock? Tom

Installing Elements 11 on Mac. Need help with install error "Setup wants to make changes."

Installing Elements 11 on Mac 10.8.2. Need help with install error: Setup wants to make changes. Type your password to allow this." After entering Adobe password, nothing happens. Locked from further installation. Any ideas? Adobe phone support could not help.

Just before letting changes (installation in this case) be made on the system, Mac OS prompts for password & this has to be the Mac system password. This password prompt is the system's own native prompt & would accept the system password only. Please make sure it is the right system password (all/admin rights) and the installaion should run.

Help with installing 10.6.3

Hello, I'm looking for a bit of help with installing Mac OS X 10.6.3 without screwing up.
I currently have a Macbook with 10.6.3 on it, and I want to COMPLETELY reset my Mac. I want to have a pretty much brand new Mac with 10.6.3, which I have the disk for. I actually just updated from 10.5.8, hoping that it would erase my hard drive and re-install, but it didn't. So I would like help with how to completely reset my Mac, and re-install 10.6.3.
Thanks in advance!
~Dan

Use that disk, but after booting from it and before running the install, choose Disk Utility from the Utilities menu and erase the drive.
(75462)

Hello I need your help with installing the flash drive into my laptop

Hi
I am Rachel Friedman asking for your help with installing the flashdrive player into my laptop.
Thanks
Rachel

To give you any useful advice, I'm going to need to know more about your computer and browser:
https://forums.adobe.com/message/5249945#5249945

MOVED: help with installing 2 os on one hd

This topic has been moved to Operating Systems.
help with installing 2 os on one hd

RedMoose:
Congratulations on installing an upgraded HDD into your PowerBook.
I am not sure exactly what happened in the formatting process, but here are some directions that should help:
Formatting, Partitioning Zeroing a Hard Disk Drive
Warning! This procedure will destroy all data on your Hard Disk Drive. Be sure you have an up-to-date, tested backup of at least your Users folder and any third party applications you do not want to re-install before attempting this procedure.
Boot from the install CD holding down the "C" key.
Select language
Go to the Utilities menu (Tiger) Installer menu (Panther & earlier) and launch Disk Utility.
Select your HDD (manufacturer ID) in left side bar.
Select Partition tab in main panel. (You are about to create a single partition volume.)
Select number of partition in pull-down menu above Volume diagram.
(Note: 1 partition is normally better for an internal HDD. External HDDs usually have more than one. See Dr. Smoke’s FAQ Backup and Recovery for tips on partitioning external HDD.)
Type in name in Name field (usually Macintosh HD)
Select Volume Format as Mac OS Extended (Journaled)
Click Partition button at bottom of panel.
Select Erase tab
Optional: (Select the sub-volume under Manufacturer ID (usually Macintosh HD).
Check to be sure your Volume Name and Volume Format are correct.
Select on Security Options button (Tiger) Options button (Panther & earlier).
Select Zero all data. (This process will map out bad blocks on your HDD. However, it could take several hours. If you want a quicker method, don't go to Security Options and just click the Erase button.)
Click OK.
Click Erase button
Quit Disk Utility.
Open installer and begin installation process.
Please post back with further questions, comments or an update.
Good luck.
corneius

No audio output device is installed (HP ENVY 700)

I have no sound at all on my pc , either with my headphones or with the basic sound of the pc . I can not access the volume mixer. I have verified that my drivers are up to date . In recording device there is nothing, no audio device is installed in recording and sound.
Exploitation systeme : Windows 8.1 64 bits
Model : HP Envy 700-339

Hello @Matsau14,
I understand that your HP ENVY 700-339 Desktop PC has no audio and no audio devices installed even with your drivers up to date. I suggest that you try a back and factory recovery of your computer to ensure that you do not have a hardware issue.
To backup your personal information and ensure that it is not lost I would like you to review and follow the steps set out in the HP Support document: Backing Up Your Files (Windows 8), which will ensure your personal files are up to date.
***WARNING!! If you want to keep any emails or bookmarks/favorites you will want to back those up as well as I do not believe they are backed up in the HP Backup process.
Next, I would like you to review and follow the steps set out in the HP Support document: Performing an HP System Recovery (Windows 8), which will you through recovering your computer back to factory settings.
*** IMPORTANT - Your personal files such as libraries, personalization settings, user accounts, and desktop themes are permanently removed. As well the computer settings are returned to the defaults (the way it was when it came from the factory). All apps and software that were installed on the computer when it came from the factory are reinstalled, and their settings are reset to the defaults. Additionally, software, apps, programs, and everything that you have installed or saved on the computer are permanently removed.
If the above steps did not resolve your issue please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I would like to thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

HP Envy 700-214 desktop drivers not ready for Windows 10 Prime Time

Really disappointed in HP for not being ready for W10 rollout. I upgraded my HP Envy desktop PC 700-214 and after the upgrade, I could not connect to the internet. Didn't recognize the networking hardware. Went to HP Support (on different computer) and found out here aren't W10 drivers yet for this machine. Very Poor.My wife has a Dell laptop and we have another older Dell that upgraded no problem. Why because Dell is on top of their $__t when it comes to this stuff.Won't by HP again.

MrDimplz wrote:
Really disappointed in HP for not being ready for W10 rollout. I upgraded my HP Envy desktop PC 700-214 and after the upgrade, I could not connect to the internet. Didn't recognize the networking hardware. Went to HP Support (on different computer) and found out here aren't W10 drivers yet for this machine. Very Poor.My wife has a Dell laptop and we have another older Dell that upgraded no problem. Why because Dell is on top of their $__t when it comes to this stuff.Won't by HP again.Did you not try to reinstall the last support Drivers into Windows 10 to see if it works? Also with the lastest Windows HP will probably not support redoing drivers for older system as that will be cost prohibited to do. And it will be up to the Endusers to find the right drivers and software that matches their system to work with Windows 10 assuming they work with Windows 10. As to Dell that is something only Dell can answer that question and since we don't know if this is Dell Consumer or Business product since this falls outside of HP forums to discuss. You can't expect to have drivers if your system is too old to support Windows 10.

Help with Installing flash error- metafile cannot be loaded

I read the forum on this but it ended last year and there was no response to some recent questions on this and the direct email to the Adobe rep. on there got no response.
I am having this problem with installing Flash- it gets about 30% of the way and then a message comes up that says the metafile cannot be loaded.
I am running 10.7.5 on Mac, all browser software is current. I use both Safari and Chrome. After it said Flash was out of date I tried to update but got the metafile error. So I uninstalled Flash to install it fresh but the same error came up. I tried everything recommended from the forum. I also did all the steps from the help list direct from Adobe ( deleting Flash files, folders, rebooting, etc.) The offline link Adobe provides says the "file cannot be found" so I can't download that either. So I tried the online link download, but even after doing all the steps in order etc. I still get the error when I try to install it.
I have no firewall and have no virus software running. I also tried the direct offline links that others have provided from 2013, (unfortunately they are old) in both clicking on them and also downloading by right click but they are dead links and even the download for it has no content.
Any help that is more recent than last year? If this is in the wrong place, apologies. New to the forum.

I tried all solutions but one posted in adobe support. I am local administrator but IE security settings are set by group policies and buttons in tools security setting are grayed out.
After three days with "The ActiveX control for Flash Player could not be registered" message I tried registering the activeX control manually.
Bingo! that made the trick.
So open a DOS window, type "regsvr32.exe C:\WINDOWS\system32\Macromed\Flash\Flash10d.ocx" -first check if this directory exists and contains the Flash10d.ocx (no quotes needed) and you should receive a confirmation that it registered correctly.
I must say that I've tried so many ways that I cannot repeat the correct order before this has worked ;-(
Hope it works for you all

Help with installing pre-requisite packages on Red Hat Linux

Having issue with installing packages with yum
OS is RHEL 6 and following package which are prerequisites for Oracle Fusion Middleware install on Red Hat Linux 6
uname details as follows
2.6.32-220.el6.x86_64 #1 SMP Wed Nov 9 08:03:13 EST 2011 x86_64 x86_64 x86_64 GNU/Linux
Example error: yum install gives error as follows for all packages.
No package compat-libcap1-1.10-1 available
Need to install following packages (as mentioned in the prerequisites)
binutils-2.20.51.0.2-5.28.el6
compat-libcap1-1.10-1
compat-libstdc++-33-3.2.3-69.el6 for x86_64
compat-libstdc++-33-3.2.3-69.el6 for i686
gcc-4.4.4-13.el6
gcc-c++-4.4.4-13.el6
glibc-2.12-1.7.el6 for x86_64
glibc-2.12-1.7.el6 for i686
glibc-devel-2.12-1.7.el6 for i686
libaio-0.3.107-10.el6
libaio-devel-0.3.107-10.el6
libgcc-4.4.4-13.el6
libstdc++-4.4.4-13.el6 for x86_64
libstdc++-4.4.4-13.el6 for i686
libstdc++-devel-4.4.4-13.el6
libXext for i686
libXtst for i686
FYI: If this forum is not appropriate please let me know appropriate forum and shall repost there.

Hey,
Normally I use YUM : http://taliphakanozturken.wordpress.com/2012/03/17/how-to-use-yum-to-install-rpm-packages-with-dependencies/
Let me know if this is what are you looking for.
I hope it helps you,
Thiago Leoncio.

Help with installing CS2 in Snow Leopard

Can anyone help me with installing CS2 on a MacBook running OSX Snow Leopard? I have trouble with activating the product and get a splach screen with a monkey element or logo rather than the adobe logos... confusion reigns!

Hi Rory, be aware that running CS2 products on Snow Leopard isn't going to be a supported combination. Here's a related thread: http://forums.adobe.com/thread/499253. Apparently some customers have been able to run CS2 software on Snow Leopard. You can also check with our chat support at http://adobe.ly/v6wfLL. However, I can't be certain that they'll be able to assist you. You might want to consider upgrading.

Need help with installing old version of firmware

I would like to revert to an old version of firmware for my Airport Extreme base station. I have read in a number of postings that this would possibly help with the problem of my Canon Pixma ip3000 not working after the firmware was usdated. When I tried to install the old firmware, the Installer would not allow it, there was just a message that the software was up to date. Could anyone please give a step by step description of how this can be done? Is there a way around the Installer? Thanks.

The firmware supplied with the base station was 4.1. After installing it, everything worked just fine, including wireless printing to a Canon Pixma ip3000. At one point, after being prompted by a message onscreen to upgrade to 4.2, I did the download and installation, and that is when all the problems started. No wireless printing, and I can't seem to use the Airport Admin or Assistant (not responding). Since then I have also upgraded the OS to 10.4.5.
I am trying to downgrade to 4.1 since that is what worked initially and what was suggested in another posting I read.
I did look at the information for the various parts of Airport and noticed that the Setup Asistant is 4.2, the Admin Utility is 4.2 and the base station is 5.5.1. Could this be affecting the problem as well?
I will try downgrading using the link you provided. Thanks very much.

Need help with installing on Photosmart C7280 all-in-one

I did have my printer installed, and was using the printer for 3 laptops wireless within my home. Now I can not even find my Backup disk, so i need help with downloading the software to use my printer, and also get it back to being used wireless. I do not know what happened, but the fax for this printer is listed, just not the printer itself. please help!
This question was solved.
View Solution.

Click here to download the software for your printer:
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?product=3204785&lc=en&cc=us&dlc=en&lang=en&cc=us
chose the appropriate operating system that corresponds to your computer and download the full feature software.
Please click on KUDOS if you find my solution helpful.

Help with installing CS3 on new Mac

Recently purchased new Macs for the department. Cannot install CS3! It asks for the CS2 license number which we have. Turns out it doesn't recognize it. Called customer support and everyone had the same answer, but no solution. I purchased the CS2 corporate license when we had about 6 Macs. Now, we're down to 3 so I purchased the CS3 as individual suites. They said there is no workaround with getting CS3 to recognize the CS2 license! We called 4 different times and talked to 4 different reps who gave us all the same broken-record response. Any help with be greatly appreciated!

I believe that is essential what the customer service folks were telling my designer. However, both was installed before on the old Macs (CS2 corporate licensed and CS3 individual license) - that's the odd thing, is that it worked before on an older system. All we did was buy new hardware.
I hope this isn't Adobe's way of making us upgrade to CS4 - lol!

Help with installing SAP

Hi Everyone,
We are currently undergoing a restructure of SAP and I have been tasked with the installation of SAP in our environment.
The systems I have been tasked with installing is the following
ECC (Enterprise Core Component)
BW (Business Warehouse)
SRM (Supplier Relationship Management)
EP (Enterprise Portal)
PI (Process Integration
I have been wandering around on the SAP website and found a load of documents referring to the install however I don't seem to be able to find the correct software or guides to help me with installation of these system.
Please could someone help me by giving me the links to the documents that I would require. Also I would like to know how do I actually install each system? Can I download all the applications on this site? Any other information you could give me would be great.
Regards,

Hi,
you'll find all the guides via service.sap.com/instguides or via the new site support.sap.com via documentation.
lots of work to install ECC, BW, SRM, EP and PI for Development(, Test) and Production.
kind regards,
Martin

Help with installing hp envy 700-214 pc series drivers

Similar Messages

Maybe you are looking for