Help with motherboard connections...

guys could u please help me out wit the cable connections to the motherboard..
jus bought the new components today to assemble my cpu..
Proc: AMD Athlon X2 3600
MB : MSI K9AGM2
Ram : 1gb kingston ddr2 667mhz
HD: Samsung spinpoint(40 gb) IDE
drive : Samsung CDRW+DVD combo
as of now...i've put in the motherboard,made the basic connections except
but the 'speaker' wire from the cabinet,supply for the Cabinet fan..
SO COULD U JUS GIVE ME A STEP-BY-STEP GUIDE TO CHECK ALL CONNECTIONS BEFORE POWERIN IT ON ???
btw,this is my first time...assembling a cpu..
REALLY APPRECIATE THE HELP..
THNX.
shown below are pics of wat i've done so far..

thnx all..i actually was right with my connections after all...after much apprehension i turned it on a few hours after i first posted here and it FIRED UP INSTANTLY WITH NO PROBLEMS WHATSOEVER !
i was worried b'coz there was no slot to insert the 'cabinet speaker' pin & whether the board had an onboard speaker..
and "vernonion"..the psu i use came with my mercury cabinet..it's a 300w mercury psu and yes its only got a 20pin connector..
considering i don't use any graphics card nor any extra devices i feel this is enough for now..

Similar Messages

  • Can someone help with a connection problem?

    I have a DroidX2 and have noticed that the phone routinely switches from 3G to 1X, especially in certain rooms in the house..
    This is consistant and usually the signal is only two bars.
    Whenever I try to watch a Youtube video it will play for maybe 12 seconds and then I will have to play with the settings in Youtube to download more of the video. Maybe 1 out of 50 times the video plays straight through without stopping. Most of the time the screen will show 1X instead of 3G. Could it be my phone settings, phone coverage or Youtube causing the problem? I sometimes have dropped calls as well. I have the most current software and Youtube was recently updated. I am also receiving "cannot establish a connection" messages on Youtube. Can someone please help? Thank you.

        Lorenzo1950, thanks for posting! Are you still having issues with your connections? What is your zip code? How long has this been an issue? Does this issue with streaming video only happen at home or everywhere?^SP

  • Can you help with my connection issues

    I cannot connect to my Contribute CS3 even though my server is fine. Does anyone have any suggestions? I spent the last hour on the phone with my server company and they tried but failed to help me connect.

    Please try the following steps.
    Delete the existing connection from Edit -> My connection .
    Create a new connection and when you Click the Advanced button next to the "How do you connect to your web server?" field in the Connection Information dialog box.
    Try toggling the Passive Mode check box (if it is unchecked, check it; if it is checked, uncheck it).
    If you are behind a firewall, check the Use firewall/proxy settings when connecting check box and click the Firewall Settings or Proxy Settings button to enter firewall information. Ask your local network administrator for help with these settings.
    Once done with the new connection you would be able to connect to your website. For more information on connection issues you may use this link http://helpx.adobe.com/contribute/kb/troubleshoot-connection-problems-contribute.html
    Regards,
    Rajeev

  • [8i] Need help with hierarchical (connect by) query

    First, I'm working in 8i.
    My problem is, I keep getting the error ORA-01437: cannot have join with CONNECT BY.
    And, the reason I get that error is because one of the criteria I need to use to prune some branches with is in another table... Is there anyway to work around this? I tried an in-line view (but got the same error). I thought about using the connect by query as an in-line view and filtering off what I don't want that way, but I'm not sure how to filter out an entire branch...
    Here is some simplified sample data:
    CREATE TABLE     bom_test
    (     parent          CHAR(25)
    ,     component     CHAR(25)
    ,     qty_per          NUMBER(9,5)
    INSERT INTO     bom_test
    VALUES     ('ABC-1','101-34',10);
    INSERT INTO     bom_test
    VALUES     ('ABC-1','A-109-347',2);
    INSERT INTO     bom_test
    VALUES     ('ABC-1','ABC-100G',1);
    INSERT INTO     bom_test
    VALUES     ('ABC-1','1A247G01',2);
    INSERT INTO     bom_test
    VALUES     ('ABC-100G','70052',18);
    INSERT INTO     bom_test
    VALUES     ('ABC-100G','M9532-278',5);
    INSERT INTO     bom_test
    VALUES     ('1A247G01','X525-101',2);
    INSERT INTO     bom_test
    VALUES     ('1A247G01','1062-324',2);
    INSERT INTO     bom_test
    VALUES     ('X525-101','R245-9010',2);
    CREATE TABLE     part_test
    (     part_nbr     CHAR(25)
    ,     part_type     CHAR(1)
    INSERT INTO     part_test
    VALUES     ('ABC-1','M');
    INSERT INTO     part_test
    VALUES     ('101-34','P');
    INSERT INTO     part_test
    VALUES     ('A-109-347','P');
    INSERT INTO     part_test
    VALUES     ('ABC-100G','M');
    INSERT INTO     part_test
    VALUES     ('1A247G01','P');
    INSERT INTO     part_test
    VALUES     ('70052','P');
    INSERT INTO     part_test
    VALUES     ('M9532-278','P');
    INSERT INTO     part_test
    VALUES     ('X525-101','M');
    INSERT INTO     part_test
    VALUES     ('1062-324','P');
    INSERT INTO     part_test
    VALUES     ('R245-9010','P');This is the basic query (with no pruning of branches):
    SELECT     LEVEL
    ,     b.component
    ,     b.parent
    ,     b.qty_per
    FROM     bom_test b
    START WITH          b.parent     = 'ABC-1'
    CONNECT BY PRIOR     b.component     = b.parentThe query above gives the results:
          LEVEL COMPONENT                 PARENT                        QTY_PER
          1.000 101-34                    ABC-1                          10.000
          1.000 A-109-347                 ABC-1                           2.000
          1.000 ABC-100G                  ABC-1                           1.000
          2.000 70052                     ABC-100G                       18.000
          2.000 M9532-278                 ABC-100G                        5.000
          1.000 1A247G01                  ABC-1                           2.000
          2.000 X525-101                  1A247G01                        2.000
          3.000 R245-9010                 X525-101                        2.000
          2.000 1062-324                  1A247G01                        2.000
    9 rows selected....but I only want the branches (children, grandchildren, etc.) of part type 'M'.
    e.g.:
          LEVEL COMPONENT                 PARENT                        QTY_PER
          1.000 101-34                    ABC-1                          10.000
          1.000 A-109-347                 ABC-1                           2.000
          1.000 ABC-100G                  ABC-1                           1.000
          2.000 70052                     ABC-100G                       18.000
          2.000 M9532-278                 ABC-100G                        5.000
          1.000 1A247G01                  ABC-1                           2.000Any suggestions?

    Hi,
    user11033437 wrote:
    First, I'm working in 8i.
    My problem is, I keep getting the error ORA-01437: cannot have join with CONNECT BY.
    And, the reason I get that error is because one of the criteria I need to use to prune some branches with is in another table... Is there anyway to work around this? I tried an in-line view (but got the same error). Post your query. It's very hard to tell what you're doing wrong if we don't know what you're doing.
    ...but I only want the branches (children, grandchildren, etc.) of part type 'M'.
    e.g.:
    LEVEL COMPONENT                 PARENT                        QTY_PER
    1.000 101-34                    ABC-1                          10.000
    1.000 A-109-347                 ABC-1                           2.000
    1.000 ABC-100G                  ABC-1                           1.000
    2.000 70052                     ABC-100G                       18.000
    2.000 M9532-278                 ABC-100G                        5.000
    1.000 1A247G01                  ABC-1                           2.000
    You mean you want don't want the descendants (children, grandchildren, etc.) of any component whose part_type is not 'M'.
    The part_type of the component itself doesn't matter: component '101-34' is included, even though its part_type is 'P', and component 'X525-101' is excluded, even though its part_type is 'M'.
    >
    Any suggestions?Sorry, I don't have an Oracle 8.1 database at hand now. All three of the queries below get the correct results in Oracle 10.2, and I don't believe they do anything that isn't allowed in 8.1.
    You can't do a join and CONNECT BY in the same query on Oracle 8.1.
    I believe you can do one first, then the other, using in-line views. The frist two queries do the join first.
    --     Query 1: Join First
    SELECT     LEVEL
    ,     component
    ,     parent
    ,     qty_per
    FROM     (     -- Begin in-line view to join bom_test and part_test
              SELECT     b.component
              ,     b.parent
              ,     b.qty_per
              ,     p.part_type     AS parent_type
              FROM     bom_test     b
              ,     part_test     p
              WHERE     p.part_nbr     = b.parent
         )     -- End in-line view to join bom_test and part_test
    START WITH     parent     = 'ABC-1'
    CONNECT BY     parent          = PRIOR component
         AND     parent_type     = 'M'
    ;Query 2 is very much like Query 1, but it does more filtering in the sub-query, returning only rows hose part_type or whose parent's part_type is 'M". Your desired result set will be a tree taken entirely from this set. Query 2 may be faster, because the sub-query is more selective, but then again, it may be slower because it has to do an extra join.
    {code}
    -- Query 2: Join first, prune in sub-query
    SELECT     LEVEL
    ,     component
    ,     parent
    ,     qty_per
    FROM     (     -- Begin in-line view to join bom_test and part_test
              SELECT     b.component
              ,     b.parent
              ,     b.qty_per
              ,     p.part_type     AS parent_type
              FROM     bom_test     b
              ,     part_test     p
              ,     part_test     c
              WHERE     p.part_nbr     = b.parent
              AND     c.part_nbr     = b.component
              AND     'M'          IN (c.part_type, p.part_type)
         )     -- End in-line view to join bom_test and part_test
    START WITH     parent     = 'ABC-1'
    CONNECT BY     parent          = PRIOR component
         AND     parent_type     = 'M'
    {code}
    Query 3, below, takes a completely different approach. It does the CONNECT BY query first, then does a join to see what the parent's part_type is. We can easily cut out all the nodes whose parent's part_type is not 'M', but that will leave components like 'R245-9010' whose parent has part_type 'M', but should be excluded because its parent is excluded. To get the correct results, we can do another CONNECT BY query, using the same START WITH and CONNECT BY conditions, but this time only looking at the pruhed results of the first CONNECT BY query.
    {code}
    --     Query 3: CONNECT BY, Prune, CONNECT BY again
    SELECT     LEVEL
    ,     component
    ,     parent
    ,     qty_per
    FROM     (     -- Begin in-line view of 'M' parts in hierarchy
              SELECT     h.component
              ,     h.parent
              ,     h.qty_per
              FROM     (     -- Begin in-line view h, hierarchy from bom_test
                        SELECT     component
                        ,     parent
                        ,     qty_per
                        FROM     bom_test
                        START WITH     parent     = 'ABC-1'
                        CONNECT BY     parent     = PRIOR component
                   ) h     -- End in-line view h, hierarchy from bom_test
              ,     part_test     p
              WHERE     p.part_nbr     = h.parent
              AND     p.part_type     = 'M'
         )     -- End in-line view of 'M' parts in hierarchy
    START WITH     parent     = 'ABC-1'
    CONNECT BY     parent     = PRIOR component
    {code}
    I suspect that Query 3 will be slower than the others, but if the CONNECT BY query is extremely selective, it may be better.
    It would be interesting to see your findings using the full tables. Please post your observations and the explain plan output.
    As usual, your message is a model of completeness and clarity:
    <ul>
    <li>good sample data,
    <li> posted in a way people can use it,
    <li>clear results,
    <li> good explanation
    <li> nciely formatted code
    </ul>
    Keep up the good work!

  • Help with motherboard MSI 845 Ultra-C

    Hello, I have a problem with this motherboard:
    When I connect something in the PCi slot, Windows recognize there are something there, but i can´t install it because it can't recognize the drivers. I tried to change the slot, I have installed the last drivers of the motherboard and there is no way to use the PCIs slot. All the things I have tried, works perfectly in another computer, i have the original drivers and they have work time ago. If anyone can help i'll very very pleased. Thank you!
    edit: I have made a clear CMOS and it doesn't work
    Forgive muy English, but i`m spanish.
    In Spanish:
    Buenas tengo un problema con mis puertos PCIs de una placa MSI 845 Ultra-C.
    Cuando conecto algo a un puerto PCI (en concreto una tarjeta avermedia con sus drivers de casa, una tarjeta de red Realtek con sus drivers y otra tarjeta de red conceptronic c100i probadas en otros ordenadores y va perfecto) windows me dice q se a detectado un dispositivo pero nunca puede llegar a localizarlos, y ya creo q no es de los drivers. Sabeis de que puede ser?
    Ya he probado a quitarlo y ponerlo en todos los puertos cada cosa por separado, han funcionado en este pc alguna vez tambien y ahora no van. Muchas gracias por su ayuda
    Edito: Tambien he actualizado la placa base con los ultimos drivers q existian

    Quote from: Frankenputer on 25-January-08, 06:34:20
    Would you please post what is in your system, including the Power Supply (manufacturer, multiple +12V rails or single +12v rail, and the amps on the +12V rail(s)). Please include the full specifications of your system(including the operating system).  Look at my signature below to get some idea of what we'd like to know.
    INTEL Pentium 4   1.6Ghz
    256 MG DDR ram KINGSTON, 1 SLOT
    motherboard MSI 845 Ultra-C  VER:1
    power supply: HipoMedia, model:ATX-250PCC12,
    AC INPUT: 115VAC 7A 60Hz     230 VAC 4A 50 Hz
    DC OUTPUT:  +12V  13A   250W MAX
                       -12V  0.5A  250W MAX
    NVIDIA GEFORCE MX400 VGA BIOS
    HD: SEAGATE 40GB 7000rpp
    DVD- LG 4120B
    network card: conceptronic c100i
    Avermedia AVerTV 103
    windows XP Proffesional: including all sp2 updates.
    I have already tried with windows XP Home Edition, windows 2000 Proffesional and Windows 98 Second Edition.
    This is the information i know, if you need more, the audio is from the motherboard. Thank you again!

  • Help with Oracle Connection- "Input string was not in a correct format"

    Hello, can some one, anyone please help me. I have a simple VS 2005 C# application that connects to oracle. I've set it up to take the username, password and tnsname as arguments. I am using Client 9i, version 9.2.0.401 of Oracle.DataAccess.dll, and .NET Framework 2.0.
    It works fine when I run it from VS 2005, I have also set up a test machine w/o VS 2005 and ran my install package and it runs fine. I sent it to one of my co-workers and when he tries it the OracleConnection obect fails with the error.
    "Input string was not in a correct format"
    strange in that it is not an ORA error, just the identifed text!?
    Here is the code:
    ## begin code
    OracleConnection dbc = new OracleConnection();
    string sConnectString = "User Id=" + username.ToString() + ";Password=" + password.ToString() + ";Data Source=" + tnsname.ToString();
    dbc.ConnectionString = sConnectString.ToString();
    MessageBox.Show("Attempting to Connect to Oracle");
    dbc.Open();
    MessageBox.Show("Connected to Oracle: " + dbc.ServerVersion);
    ## end code
    Pretty basic, what could be going on?
    Since this only happens with an installation, I put in the message boxes to verify exactly where it chokes. I get the first message box, then an error with the identified text. I've seen a number of posts regarding input string format problems, but not a one dealing with OracleConnection.Open(). I added all the ToString() calls just to make sure everything was a string but it did not change the end result.
    Anyone? Thanks In advance!
    Eric S.

    Hello,
    well, i got a message "...string not wellformed format...", too.
    If you have defined the parameters as string, you don't need the additonal "ToString()". Please ckeck your tnsnames -string. Try to debug this. I believe you have copy the format from the tnsnames.ora and there you have much brackets.
    For example, two code snippets:
    As datasource i use <Server>:<Port>/<Instance>
    try
    string FDsn ="User Id="+FDbUser+";Password="+FDbPwd;
    FDsn +=";Data Source=wth5:1521/Ora9.wth5";
    FConn = new OracleConnection(FDsn);
    FConn.Open();
    if (FConn.State == ConnectionState.Open )
         FConn.Close();
    catch (Exception ex)
         FStateMsg = "Connection to database failed. Check Configuration in parameter: ConnectionString. " + ex.Message;
    Above i connect to a Ora 9.2.0.1
    by using
    FDsn +=";Data Source=wth5:1522/XE";
    i connect to an OraExpress database on the same machine.
    My Oracle.dataAccess.dll ist the newest, 10.2.... and it runs under Framework 1.1.x and Framework 2.x
    I'll hope it will help you. Best regards!

  • Help with problem connecting to itunes

    My son's Ipod touch is not showing up as being recognized by Itunes. We did and reset on it and now all that comes up on his screen are the icons that show to plug your ipod into the USB port so it can link with Itunes. When we plug it in nothing happens though because I do not think Ipod is being recognized.
    Don't know why or how this has happenned. he tried to jailbreak his Ipod last week but was unsuccessful. Don't know if this hurt it or not.
    Can anyone help as to what I should do?

    try connecting the device to iTunes in [_*DFU mode*_|http://www.podzombie.com/2010/01/using-dfu-mode-to-fix-ipod-touch-and-ip hone-errors>.
    JGG

  • Need help with G5 connected to AirPortExpress!

    I simply can't find the source of this problem, and any help is very welcome:
    When my G5 2x2,5GHz and OS 10.4.8 is connected to my AirPort Express network, the connection suddenly becomes very slow and it takes forever to download a simple page. The message "You are not connected to Internet" often shows up, and trying to reconnect fails. The only solution is to restart both the ADSL modem and the Airport Express.
    - The funny thing is that with my brand new MacBookPro and the old iMac G4, this never happens. They stay connected both to the network and Internet without any similiar problems.
    Could it be the wireless antenna on the back of the G5, or could it be some security settings or OSX problems on the G5? I am not sure how to find the source of the problem...
    Helge K.

    Hello Helge,
    I have a couple of questions.
    How is the speed during a file transfer between the G5 and the imac ( say a large file) compared to the iMac and the Macbook?
    Forget the web for a minute here and let zero down on the problem. Is it the current network, or a specific machine, or is it that basted ADSL modem?
    Try transferring a file over your network and compare if there is a noticeable difference then lets move that G5 away from the wall ( the ant is in the back) and try with the G5 turn 180 degrees around, any better? If not double check the ant lead that connects to the card or take in for service and have the unit inspected for a pinched/ loose cable.
    If moving a file around the network is ok then we have a web issue. Run a trace-route to Apple's main site and compare it to the macbook. What's different?
    Nothing? Then there is the famous reset Safari and test or see what Firefox does.
    Good Luck,
    Cowsweat

  • Please help with database connection issue

    Hi,
    I've created a few connections and pages with a few recodsets on my local computer and am connecting fine with the database. I've uploaded the database via phpmyadmin onto a remote server and uploaded all my pages to the website and have changed the database info, user name and password in the connections folder but when I try to load the file I get a message "no database selected". I've tried various things but no luck. I'm selecting the database name but something is missing. Any help would be appreciated.
    Derek

    A bit more info: Here is the connection script as its defined in Dreamweaver: <?php
    # FileName="Connection_php_mysql.htm"
    # Type="MYSQL"
    # HTTP="true"
    $hostname_karen_product = "localhost";
    $database_karen_product = "karen";
    $username_karen_product = "root";
    $password_karen_product = "root";
    $karen_product = mysql_pconnect($hostname_karen_product, $username_karen_product, $password_karen_product) or trigger_error(mysql_error(),E_USER_ERROR);
    ?>
    Where is says mysql_pconnect, I changed the $hostname_karen_product etc to 'localhost', 'username', 'the password for the database')
    Do i need to do something different at $database_karen_product?
    I'm basically new at this and confused as to how to alter this connection script.
    Thanks
    Derek

  • Help with database connection

    ok I am trying to use dreamweaver's database function to
    connect to a mysql database, i fill in the info and it gives me the
    following error:
    "an unidentified error has occurred"
    I know all the info i am putting in is correct as I am copy
    and pasting it directly out of my connection properties in navicat
    mysql editor which can connect to the database fine
    i tried connecting to multiple databases on multiple servers
    and every single one returned the exact same error
    I am using Dreamweaver CS3 for Mac OSx
    thx for any help
    -Ryan

    Have you gone under the Application folder and clicked on the
    plus (+) sign and created the connection to the database.
    Also, do you have username and password on the database? If
    so, you'll have to provide this information
    I don't use MAC or PHP a great deal. So my help can be rather
    limited. I'm just thinking about connection strings
    What web server are you using? MAke sure it's running and set
    up correctly. Test the server first and see if it's working. If so
    see what connections string Dreamweaver is providing. I know Apache
    had a few bugs with various version just Windows has had in the
    past, not sure how these work with OSX

  • Help with ASP Connections - New User

    I just set up a hosting account with 1 and 1 for a simple
    website to catalog a series of yo-yo contest that we coordinate. I
    have a simple MS Access database for organizing contest information
    that we are trying to get online.
    I am new to the application side of this and know very little
    about connection strings, DSN, etc. I am experiencing problems with
    connecting to the MS Access database that I have uploaded to the
    1and 1 servers. If I hardcode the Javascript into the page, I can
    connect and pull information but I definitely want to take
    advantage of the design interface that Dreamweaver MX 2004 offers.
    This is the code from the page that I can get working based
    on the FAQ Sheet that 1and 1 offers for database connections:
    <html>
    <title>Database query using ASP</title>
    <body bgcolor="FFFFFF">
    <h2>Query table <b>Products</b> with
    ASP</h2>
    <%
    Set dbaseConn = Server.CreateObject("ADODB.Connection")
    dbaseConn.Open "DRIVER={Microsoft Access Driver
    (*.mdb)};DBQ=" & Server.Mappath("\db\League.mdb") & ";"
    SQLQuery = "SELECT * FROM Contest_Information"
    Set RS = dbaseConn.Execute(SQLQuery)
    %>
    <%
    Do While Not RS.EOF
    %>
    <%=RS("cStartDate")%>, <%=RS("cName")%>,
    <%=RS("cWebsite")%> List
    <p>
    <%
    RS.MoveNext
    Loop
    RS.Close
    Set RS = Nothing
    dbaseConn.Close
    Set dbaseConn = Nothing
    %>
    </body>
    </html>
    If I put in a "Custom Connection String" using the previous
    code:
    "DRIVER={Microsoft Access Driver (*.mdb)};DBQ=" &
    Server.Mappath("\db\League.mdb") & ";"
    Dreamweaver can connect to the database when the connection
    is 'tested' but cannot pull any tables and therefore cannot create
    bindings.
    Guidance...help...I'm stuck...
    Thanks in advance.

    Hello Lucky.da.boss,
    And welcome to Apple Discussions!
    is asking can I or is there anyway i can transfer my music off that iPod to my touch?
    See this article for tips on how to copy music from your 5th generation iPod to your iTunes library. Once you have successfully done that, you can sync them over to your iPod Touch. There is no way to do it directly.
    http://macs.about.com/od/backupsarchives/ss/ipodcopy.htm
    Also, I have two applications that aren't downloading I want to know how to delete them.
    Tap your finger on one of them and hold it there until you see all your Apps start to wiggle. You will also see a small x in the upper right hand corner of the Apps you can delete. Go ahead and tap this to delete the App. When you are finished, hit the Home button to make the Apps stop wiggling. It might also help to have a look at your iPod's *User Guide.
    http://manuals.info.apple.com/enUS/iPod_touch_iOS4.1_UserGuide.pdf
    Can you have constant internet service or do they run solely off wi-fi?
    Only Wi-fi.
    B-rock

  • Help with Database Connected LiveCycle ES4 form

    Hello and thanks for taking the time to read this question, I hope you can help!
    I have a LiveCycle ES 4 form connected to an excel database.  The form has buttons to "Add", "Update" or "Find" a record.  These buttons all work correctly EXCEPT when the server drive that has the Excel file is not available.  In this case I wanted to add code the "Add" button informing the user that there is an error.  I tried adding a try/catch block before the SQL statement that inserts a record into excel but even when I purposely make the Excel file unavailable the try/catch block doesn't seem to work.  The javascript console will show an error but try/catch doesn't seem to trigger.  If I had a javascript syntax error within the try/catch block, it works as expected, but with the database connected form, it appears the try/catch block does not trigger based on errors generated as a result of the database file having an issue.  In this case, the console just shows a "GeneralError: Operation failed." message.  Why doesn't the try/catch block trigger since there is an error as stated on the console?  Is there a work around?  Thanks again for your help!!

    Hello and thanks for taking the time to read this question, I hope you can help!
    I have a LiveCycle ES 4 form connected to an excel database.  The form has buttons to "Add", "Update" or "Find" a record.  These buttons all work correctly EXCEPT when the server drive that has the Excel file is not available.  In this case I wanted to add code the "Add" button informing the user that there is an error.  I tried adding a try/catch block before the SQL statement that inserts a record into excel but even when I purposely make the Excel file unavailable the try/catch block doesn't seem to work.  The javascript console will show an error but try/catch doesn't seem to trigger.  If I had a javascript syntax error within the try/catch block, it works as expected, but with the database connected form, it appears the try/catch block does not trigger based on errors generated as a result of the database file having an issue.  In this case, the console just shows a "GeneralError: Operation failed." message.  Why doesn't the try/catch block trigger since there is an error as stated on the console?  Is there a work around?  Thanks again for your help!!

  • Help with public connections

    I have searched the forums and none of the solutions worked.
    When I try to create a discoverer connection through AS control, I get this error:
    An error occurred:oracle.disco.oem.configuration.DiscoConfigurationException: Failed to create new Connection. ORA-06510: PL/SQL: unhandled user-defined exception ORA-06512: at "ORASSO.WWSSO_API_PRIVATE", line 244 ORA-06510: PL/SQL: unhandled user-defined exception ORA-06512: at "ORASSO.WWSSO_UTL", line 546 ORA-06502: PL/SQL: numeric or value error ORA-06512: at line 1
    I've been googling it (and searching this forum) for the past 3 days and can't get it to work. Help anyone? Where should I be looking at?
    I see in the error something about SSO, checked that component and it's up (like all the others) but its start time is N/A.
    Any help is appreciated. I must create a public connection in order to put worksheets into portal!!

    AMN wrote:
    1. Is it the first public connection you are trying to make on this DB?Yes, it is.
    Ensure that an EUL is properly created and is accessible; also ensure that the database where the EUL is created is accessible from BI instance. (this means ensure the tnsnames in BI instance has an entry for it). also the user can logon successfully into the EUL without problem and have appropriate privileges;
    - use the Discoverer connection method for login;All of that is set/done properly. I can access the EUL through Discoverer Administrator and can connect to BI Discoverer directly and access the worksheet created before. I'm guessing there is nothing wrong with the EUL itself, as it is accessible.
    2. your problem though looks more on the user side. however, the root error is numeric or value error somewhere. can you share some specific details on what you are entering to create the public connection?AS for the Connection Name and Description, the login method is Oracle BI Discoverer.
    As for the Database Account Details, the EUL, username, password and database are the same I enter to connect to BI Discoverer and Disc. Administrator:
    * End User Layer: umhgsa_eul     
    * User Name: umhgsa_eul          
    * Database: intcare
    3. have you tried creating the connection through discoverer viewer? or to connect directly?I have tried through Discoverer Viewer and Discoverer EM. I can only connect directly and everything works fine since there. My huge problem is that I really need to create a public connection or else I can't use the workbooks on the portal! Is there any other way around?
    Thanks for your recommendations, AMN :)

  • Help with OBDC connection in Windows 7 64bit with Office 2010 32 bit.

    Hi,
    Many moons ago I wrote an application in Java that configured XP machines after they were sysprep’d and deployed. I am currently migrating all our workstations to Windows 7, and was checking my application still worked and queries the correct registry keys etc.
    As it turns out however I don't even get going as I believe the application is unable to connect to the ODBC Microsoft Access Driver in Windows 7 64bit with Office 2010 32 bit. Below is the code I have always used and no longer works. I am hopeful that someone can tell me how to modify the command to work on Windows 7 64bit. If I browse to C:\Windows\SysWow64\OBDCad32.exe all the drivers I need are there I think, but if I open OBDC from Administrative Tools the Drivers tab is empty but for SQL. Anyway I will shut up and below is the code I used to use:
         public IOMakeConnection()
         dm = new DisplayMessage();
         ioed = new IOEncryptDecrypt();
         url = "jdbc:odbc:DRIVER=Microsoft Access Driver (*.mdb);DBQ=" + getPath() + "Config.mdb;Uid=admin;Pwd=password";
              try
              Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
              connection = DriverManager.getConnection( url );
              catch( Exception e )
              system.out.println( "" + e );
              errorObtainingPath();
    The exception is always thrown as my little app that requests the database path always loads.
    Thanks in advance,
    Cheers Kris

    Hello again,
    Sorry for the delayed response, I have been out of the office for a few days.
    I have solved the issue, and as stated above the issue was the way I was launching the application. Below is a summary of the issue and the resolution.
    My problem was that in Windows 64bit if you click on ODBC in Administrative Tools the Drivers Tab only includes an SQL Driver, and my code reference a Microsoft Access Driver to query the database. That said however if you browse to C:\Windows\SysWow64 and open obdcab32.exe it opens the 32bit version of ODBC, and the Microsoft Access Driver (*.mdb) is listed.
    Basically what I need to do therefore is get my code to access the “32bit” version of ODBC in a Windows 7 64bit environment, so my application was able to read the necessary information from the Access Database associated with it.
    I understand that this is not a coding issue directly, but assuming people still use Java to open an Access Database on a Windows 7 64bit OS, this may be of help.
    So previously I ran the following command, from the “Target” box in a shortcut to execute the java code:
    cmd.exe /C SET CLASSPATH=C:\SCAConfigurationUtility && CD\SCAConfigurationUtility && JAVAW SCAConfigurationUtility
    Windows 7 64bit, defaults to the 64bit version of Java, and just seems to plain fail if you only have the 32bit version installed. To overcome this I forced the java executable that I was using to be the 32bit version, and used the system switches available in Java 7 (-cp does not appear to be available in Java 6)
    So my Shortcut now has this in the “Target” box:
    java.exe -d32 -cp C:\SCAConfigurationUtility SCAConfigurationUtility
    And this in the “Start in” box:
    "C:\Program Files (x86)\Java\jre7\bin"
    Or by using the target below the same shortcut works in XP
    "C:\Program Files\Java\jre7\bin"
    Thanks for all the help,
    Regards Kris.

  • Help with Access connecting to a Oracle DB on a Windows 7-64bit workstation

    Hello:
    Here's my configuration:
    OS: Windows 7-64bit
    Oracle DBMS: 11g
    I am trying to connect to a 11g DB from within Access.
    I launched the ODBC Administrator from c:\windows\syswow64 directory as an Administrator (which I undertstand is the 32-bit version). When I tried to set up a new DSN, I encountered two problems:
    1. The TNS Service Name dropdown has a slew of entries with funny characters. However, it did not include my TNS Entry.
    2.  I manually entered my TNSName. It did ask me for the username and password. When I tested the connection, I got an error "ORA-12154"
    Any help to resolve the issue will be much appreciated.
    Venki

    Senthil:
    What should it point to?
    Anyway, I re-installed both the 64-bit Oracle DB and the 32-bit client. There are two sets of TNSNames.Ora, Listener.Ora and SQLNet.ora, one for the 64-bit and one for the 32-bit in their respective folders.
    I have no problem creating an ODBC DSN for the 64-bit version. The link connects fine to the DB
    I have two TNS Listeners defined, one for the 64-bit and one for the 32-bit. While the 64-bit uses Port 1521, I am using Port 1522 for the 32-bit; I also made sure that Listener.ora refers to the same port. But when I use Oracle Net Configuration Assistant to configure Local Net Service Name Configuration to test the Service, it says "TNS:listener does not currently know of the service requested in connect descriptor.
    I did check that both the TNS Listener services are running.
    venki

Maybe you are looking for