HH5 Suffering from multiple resets overnight!

As the previous thread on this issue is now locked this is a NEW thread.
Since the 'few' HH5 suffering from these problems have been updated my one seems to be one of the remaining few that still have problems.
During the past few days my hub has suffered from restarts during the late evening and nightime hours when it is not being used. Although this does not cause any disruptions in service it does result in my IP profile being downgraded from its usual high level so my daytime performance is significantly reduced!
Last nightmy HH5 was restarted 6 times:
20:46 after 1777 minutes uptime
20:49              2 mins
01:13           263 mins
04:46           212 mins
04:48               1 mins
05:37             48 mins
As these problems only occur late evening and overnight the problem cannot be with my line or connection but more likely to be caused at the exchange end?
I hope this matter can be followed up quickly as I have been plagued by reduced speed problems (reported) over the past 3 months!

I have noticed that the resets occur every time BT try to communicate with my HH5. This invariably occurs around the same time overnight. Perhaps they are doing some overnight maintenance at the exchange which results in service interuptions?
Following are the commands sent to my HH5:
You should note that the first two TR069 commands are result in 'session closed' states. This error condition invariably results in my HH5 going into reset mode.
All TR069 commands received that are actioned without any error do not result in a reset.
Following are the actions my HH5 takes after receiving these commands:
You should note that the time this request occurs during the night is when the only internet active devices connected to the HH5 is my iPad monitoring for e-mails.
 I hope this info is enough to prompt some useful advice.

Similar Messages

  • Accessing the same object from multiple classes.

    For the life of me I can't workout how I can access things from classes that haven't created them.
    I don't want to have to use "new" multiple times in seperate classes as that would erase manipulated values.
    I want to be able to access and manipulate an array of objects from multiple classes without resetting the array object values. How do I create a new object then be able to use it from all classes rather than re-creating it?
    Also I need my GUI to recognize the changes my buttons are making to data and reload itself so they show up.
    All help is good help!
    regards,
    Luke Grainger

    As long as you have a headquarters it shouldn't be to painfull. You simply keep a refrence to your ShipDataBase and Arsenal and all your irrellevant stuff in Headquarters. So the start of your Headquarters class would look something like:
    public class Headquarters{
      public Arsenal arsenal;
      public ShipDatabase db;
    //constructor
      public Headquarters(){
        arsenal = new Arsenal(this, ....);
        db = new ShipDatabase(...);
    //The Arsenal class:
    public class Arsenal{
      public Headquarter hq;
      public Arsenal(Headquarter hq, ....){
        this.hq = hq;
        .Then in your ShipDatabase you should, as good programing goes, keep the arraylist as a private class variable, and then make simple public methods to access it. Methods like getShipList(), addToShipList(Ship ship)....
    So when you want to add a ship from arsenal you write:
    hq.db.addToShipList(ship);
    .Or you could of course use a more direct refrence:
    ShipDatabase db = hq.db;
    or even
    ShipList = hq.db.getShipList();
    but this requires that the shiplist in the DB is kept public....
    Hope it was comprehensive enough, and that I answered what you where wondering.
    Sjur
    PS: Initialise the array is what you do right here:
    //constructor
    shipList = new Ship[6];
    shipList[0] = new Ship("Sentry", 15, 10, "Scout");
    " " " "etc
    shipList[5] = new Ship("Sentry", 15, 10, "Scout");PPS: To make code snippets etc. more readable please read this article:
    http://forum.java.sun.com/faq.jsp#messageformat

  • Can I use accounts in the Airport Utility to keep backup from multiple macs separate and separate?

    Can I use accounts in the Airport Utility to keep backup from multiple macs separate and separate?

    Backups from multiple Macs are always kept separate. Each Mac TM will create its own sparsebundle and will not interfere with others.
    Using the accounts in AU will simply make each sparsebundle only accessible to that user.. ie it is a purely a security measure.. that is so weak as to be useless .. anyone can bypass it by pressing the reset for 1sec.
    And what it will do is cut off everyone from their existing backups.. you will be warned when you set it up that what is about to happen may not be 100% goodness.. pay attention.. it is not.

  • My early 2008 Macbook Pro is suffering from black screen after Yosemite update

    My early 2008 Macbook Pro is suffering from black screen after Yosemite update. It ran beta 5 great but failed on restart after beta 6 install. There is no cursor but I can hear the HDD spooling up. I have tried booting in safe mode, PRAM reset and SMC reset but nothing works. After the first 5 days of every now and then trying to start it, it started fine. I used the machine all day with no problems, it had rolled back the install and was back on beta 5. I decided to try the update again, the same thing happened and it has stayed black for over a week now. It wont work with a monitor either. Help!

    Hello Adam,
    I would try instead of installing the beta software, to install the official build of OS X Yosemite from the Mac App Store to see if that gets you passed the no video issue when updating the beta software. 
    How to install OS X Yosemite on your Mac
    http://support.apple.com/en-us/HT6412
    Regards,
    -Norm G.  

  • Unable to use AirPlay from multiple iOS and MacBook pro

    HI, I seem to be having issues using AirPlay From multiple iOS devices.
    I have the following devices, iphone 6 plus, iPad air (both Gen 1 and 2) an iPad 2 and a MacBook Pro running Yosemit. I also have 2 Apple TVs (both gen 1 and 2).
    Recently I have found that I am unable to use AirPlay on any of the iOS devices to either Apple TVs, the MacBook Pro will Airplay mirror ok, I am however able to use iTunes shairing from a Windows 8PC. I have restarted and also reset both Apple TVs and my router, I have also reset the connection settings on all the iOS devices but still can't resolve the issue.
    The Apple TVs have Internet connection so I can't see any issues network connections.
    ANyone else got got any Ideas?
    Thanks

    Try the following steps, check whether things are working after each step where appropriate, before trying the next.
    Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
    Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
    Restart the Apple TV (Settings > General > Restart).
    Restart the Apple TV by removing ALL the cables for 30 seconds.
    Restart your router. (Also try removing it’s power cord for at least 30 seconds)
    Restart your mobile device.
    If you are still having problems, the following article(s) may help you.
    Troubleshooting AirPlay
    Troubleshooting Wi-Fi networks and connections
    Recommended Wi-Fi settings
    Wifi Diagnostic Software (for Mac users)
    You may also find some help on this page, where I’ve collected some of the more unusual solutions to network issues.
    When making adjustments to your network for better optimisation, you may find some of the points mentioned on this page helpful.
    This is answer is provided from my own database of boilerplate responses and the content was last reviewed and/or tested on: 2014/12/16

  • Acrobat 8 - Create PDF from multiple images, they all come in bigger dimension

    I have 9 TIFFS that are 1000 x 750 in size, 72 DPI. This is confirmed when I open them up in Photoshop. When I create a PDF from multiple files in Acrobat, they all come in much bigger in dimension. The resulting PDF is very big in dimensions.
    I have searched the Internet and searched the Help/Manual and can't seem to fix this.
    Any help would be greatly appreciated.
    Thanks!
    Scot

    Scot,
    Try going to Acrobat > Preferences > Page Display > Resolution and reset to 72 pixels / inch. I hope that helps!
    Chris

  • Export video from multiple iOS devices to a Mac without using iTunes

    I am tasked with importing video files from multiple iPads to a single Mac to aggregate for editing.
    The file sizes on each device are many gigs large. I don't want to use iMovie on the Mac or iOS.
    I don't want to use iTunes (since there are many iPads not owned by me to import video from).
    Suggestions?
    Paul
    Chicago

    iTunes. Other than that there is no direct method. However, do try the iPhone forums.

  • How To Concatenate Column Values from Multiple Rows into a Single Column?

    How do I create a SQL query that will concatenate column values from multiple rows into a single column?
    Last First Code
    Lesand Danny 1
    Lesand Danny 2
    Lesand Danny 3
    Benedi Eric 7
    Benedi Eric 14
    Result should look like:
    Last First Codes
    Lesand Danny 1,2,3
    Benedi Eric 7,14
    Thanks,
    David Johnson

    Starting with Oracle 9i
    select last, first, substr(max(sys_connect_by_path(code,',')),2) codes
    from
    (select last, first, code, row_number() over(partition by last, first order by code) rn
    from a)
    connect by last = prior last and first = prior first and prior rn = rn -1
    start with rn = 1
    group by last, first
    LAST       FIRST      CODES                                                                                                                                                                                                  
    Lesand         Danny          1,2,3
    Benedi         Eric           7,14Regards
    Dmytro

  • Can we merge data from multiple sources in Hyperion Interactive Reporting ?

    Hi Experts,
    Can we merge data from multiple sources in Hyperion Interactive Reporting ?Example can we have a report based on DB2
    Oracle,
    Informix and Multidiemnsional Databases like DB2,MSOLAP,ESSBASE?
    Thanks,
    V

    Yes, Each have their own Query and have some common dimension for the Results Sections to be joined together in a final query.
    look in help for Creating Local Joins

  • Accessing the same stateful session bean from multiple clients in a clustered environment

    I am trying to access the same stateful session bean from multiple
              clients. I also want this bean to have failover support so we want to
              deploy it in a cluster. The following description is how we have tried
              to solve this problem, but it does not seem to be working. Any
              insight would be greatly appreciated!
              I have set up a cluster of three servers. I deployed a stateful
              session bean with in memory replication across the cluster. A client
              obtains a reference to an instance of one of these beans to handle a
              request. Subsequent requests will have to use the same bean and could
              come from various clients. So after using the bean the first client
              stores the handle to the bean (actually the replica aware stub) to be
              used by other clients to be able to obtain the bean. When another
              client retrieves the handle gets the replica aware stub and makes a
              call to the bean the request seems to unpredictably go to any of the
              three servers rather than the primary server hosting that bean. If the
              call goes to the primary server everything seems to work fine the
              session data is available and it gets backed up on the secondary
              server. If it happens to go to the secondary server a bean that has
              the correct session data services the request but gives the error
              <Failed to update the secondary copy of a stateful session bean from
              home:ejb20-statefulSession-TraderHome>. Then any subsequent requests
              to the primary server will not reflect changes made on the secondary
              and vice versa. If the request happens to go to the third server that
              is not hosting an instance of that bean then the client receives an
              error that the bean was not available. From my understanding I thought
              the replica aware stub would know which server is the primary host for
              that bean and send the request there.
              Thanks in advance,
              Justin
              

              If 'allow-concurrent-call' does exactly what you need, then you don't have a problem,
              do you?
              Except of course if you switch ejb containers. Oh well.
              Mike
              "FBenvadi" <[email protected]> wrote:
              >I've got the same problem.
              >I understand from you that concurrent access to a stateful session bean
              >is
              >not allowed but there is a
              >token is weblogic-ejb-jar.xml that is called 'allow-concurrent-call'
              >that
              >does exactly what I need.
              >What you mean 'you'll get a surprise when you go to production' ?
              >I need to understand becouse I can still change the design.
              >Thanks Francesco
              >[email protected]
              >
              >"Mike Reiche" <[email protected]> wrote in message
              >news:[email protected]...
              >>
              >> Get the fix immediately from BEA and test it. It would be a shame to
              >wait
              >until
              >> December only to get a fix - that doesn't work.
              >>
              >> As for stateful session bean use - just remember that concurrent access
              >to
              >a stateful
              >> session bean is not allowed. Things will work fine until you go to
              >production
              >> and encounter some real load - then you will get a surprise.
              >>
              >> Mike
              >>
              >> [email protected] (Justin Meyer) wrote:
              >> >I just heard back from WebLogic Tech Support and they have confirmed
              >> >that this is a bug. Here is their reply:
              >> >
              >> >There is some problem in failover of stateful session beans when its
              >> >run from a java client.However, it is fixed now.
              >> >
              >> >The fix will be in SP2 which will be out by december.
              >> >
              >> >
              >> >Mike,
              >> >Thanks for your reply. I do infact believe we are correctly using
              >a
              >> >stateful session bean however it may have been misleading from my
              >> >description of the problem. We are not accessing the bean
              >> >concurrently from 2 different clients. The second client will only
              >> >come into play if the first client fails. In this case we want to
              >be
              >> >able to reacquire the handle to our stateful session bean and call
              >it
              >> >from the secondary client.
              >> >
              >> >
              >> >Justin
              >> >
              >> >"Mike Reiche" <[email protected]> wrote in message
              >news:<[email protected]>...
              >> >> You should be using an entity bean, not a stateful session bean
              >for
              >> >this application.
              >> >>
              >> >> A stateful session bean is intended to be keep state (stateful)
              >for
              >> >the duration
              >> >> of a client's session (session).
              >> >>
              >> >> It is not meant to be shared by different clients - in fact, if
              >you
              >> >attempt to
              >> >> access the same stateful session bean concurrently - it will throw
              >> >an exception.
              >> >>
              >> >> We did your little trick (storing/retrieving handle) with a stateful
              >> >session bean
              >> >> on WLS 5.1 - and it did work properly - not as you describe. Our
              >sfsb's
              >> >were not
              >> >> replicated as yours are.
              >> >>
              >> >> Mike
              >> >>
              >> >> [email protected] (Justin Meyer) wrote:
              >> >> >I am trying to access the same stateful session bean from multiple
              >> >> >clients. I also want this bean to have failover support so we want
              >> >to
              >> >> >deploy it in a cluster. The following description is how we have
              >tried
              >> >> >to solve this problem, but it does not seem to be working. Any
              >> >> >insight would be greatly appreciated!
              >> >> >
              >> >> >I have set up a cluster of three servers. I deployed a stateful
              >> >> >session bean with in memory replication across the cluster. A client
              >> >> >obtains a reference to an instance of one of these beans to handle
              >> >a
              >> >> >request. Subsequent requests will have to use the same bean and
              >could
              >> >> >come from various clients. So after using the bean the first client
              >> >> >stores the handle to the bean (actually the replica aware stub)
              >to
              >> >be
              >> >> >used by other clients to be able to obtain the bean. When another
              >> >> >client retrieves the handle gets the replica aware stub and makes
              >> >a
              >> >> >call to the bean the request seems to unpredictably go to any of
              >the
              >> >> >three servers rather than the primary server hosting that bean.
              >If
              >> >the
              >> >> >call goes to the primary server everything seems to work fine the
              >> >> >session data is available and it gets backed up on the secondary
              >> >> >server. If it happens to go to the secondary server a bean that
              >has
              >> >> >the correct session data services the request but gives the error
              >> >> ><Failed to update the secondary copy of a stateful session bean
              >from
              >> >> >home:ejb20-statefulSession-TraderHome>. Then any subsequent requests
              >> >> >to the primary server will not reflect changes made on the secondary
              >> >> >and vice versa. If the request happens to go to the third server
              >that
              >> >> >is not hosting an instance of that bean then the client receives
              >an
              >> >> >error that the bean was not available. From my understanding I
              >thought
              >> >> >the replica aware stub would know which server is the primary host
              >> >for
              >> >> >that bean and send the request there.
              >> >> >
              >> >> >Thanks in advance,
              >> >> >Justin
              >>
              >
              >
              

  • Selecting data from Multiple Partitions in a single select stmt.

    Hi all,
    My Database is very large & my tables are partitioned.
    My question is:
    1) If my data is spread across multiple partitions, is there any way to select data from multiple partitions in a single query?
    If we dont mention partition name also it works fine, but perofmance wise it will be very slow. (Using EXPLAIN PLAN)
    (Note:I dont want to make use of Union concept, i want to do it in a single select statement)
    For ex:
    qry1.sql:
    select empno from emp_trans partition (P012000)
    This above query(qry1.sql) will work fine.
    qry2.sql:
    select empno from emp_trans partition (P012000,P022000)
    The above query(qry2.sql) will return will return the following error:
    ORA-00933: SQL command not properly ended
    If anybody has any solution for this, pls mail me immediately.
    Thanks in advance
    bye
    null

    All my queries are dynamically generated. All my tables are also indexed partition wise based on date field. My question is, if i want to mention multiple partition names at the time of generating my query(select), then with parformance will be good. I have refered some books, inthat what they say is to use UNION concept, i dont want to use that, instead i want in a single select statement.
    Thaks for ur reply
    Bye
    null

  • How to load data to a cube from multiple infosources ?

    Hi friends,
    How to load data to a cube from multiple infosources ? could u please answer this question .
    thanks in advance......

    Hi ,
    say for example you need to load data to 1 cube from 3 info sources:
    1) You need to create 3 update rules for the Cube.
    2) Each time you create the update rules. Mention the name the name of the Info source. and create update rules correspondingly.
    Regards
    satish
    Message was edited by:
            satish murthy

  • Display Data from multiple models in one table

    Hi Experts,
    Is it possible to display data from multiple models in one table smltnsly.
    I have created a table dynamically.Now I would like to display data from multiple models... If this possible,can anyone give me a lead as to how to do it..
    Regards
    SU

    Hi
    Your Model Nodes be
    Model1
    ---Output_Model1
    Attrib1
    Attrib2
    Model2
    ---Output_model2
    Attrib1
    Attrib2
    and the value node is
    ValueNode
    ---Attrib1
    ---Attrib2
    Now the coding.
    int size;
    IPrivate<ViewName>.IOutput_mode1Node  node1 = wdContext.nodeOuptut_Model1();
    IPrivate<ViewName>.IValueNodeElement elem;
    size = node1.size();
    for(int i=0; i<size; i++)
       elem = wdContext.createValueNodeElement();
       elem.setAttrib1( node1.getOutput_Model1ElementAt(i).getAttrib1() );
       elem.setAttrib2( node1.getOutput_Model1ElementAt(i).getAttrib2();
       wdContext.nodeValueNode().addElement( elem );
    similar code for Model Node 2
    Regards
    Abhimanyu L

  • Display data from multiple document Libraries in List View Webpart

    Hi All,
    I want to display data from multiple document libraries into one list view webpart(custom i have created)
    I went through the following link http://blogs.msdn.com/b/ramg/archive/2009/04/22/implementing-a-simple-cross-site-collection-list-view-webpart.aspx
    but it tells to display only from one document library.
    My motive behind displaying data in the list view webpart is to achieve the functionality of Check In ,Check Out and other OOB features.
    With Regards,
    Jaskaran Singh

    Hi,
    As there is no such OOTB feature, a workaround is to create a visual web part to gather items from libraries and implement functionalities like Check in, Check out files
    in different libraries.
    The links below will provide more details:
    Create Visual Web Parts in SharePoint
    2010
    A demo about displaying list items in visual web part:
    http://www.dotnetcodesg.com/Article/UploadFile/2/217/Web%20Part%20in%20SharePoint%20To%20Show%20All%20List%20and%20List%20Items.aspx
    About the Check In and Check Out:
    How to Check In a document programmatically
    SPFile.CheckIn method
    and SPFile.CheckOut method
    Best regards
    Patrick Liang
    TechNet Community Support

  • How to create a report from multiple dynamic XMLs

    Hi,
    I'm trying to build a consolidated report that gets data from multiple XML files and each XML file is different. Although the presentation of the data will be similar, the contents of the XMLs will vary and the number of XMLs to merge will also vary.
    What I would like to understand is the following:
    * Is it possible to generate a report template based on dynamic columns where the column names, their format and number is different for each business object?
    * Is it required to generate an XML with the entire data or can the template read information from different XML files? and if so how it can be done. Please notice that the formatting of each XML may be different.
    * Is it possible to use the services to generate the reports directly? Something around these lines was mentioned in one of the sessions but it was also mentioned that it's still WIP.
    I've been using the standalone version and although I can get the desired result, I couldn't merge data from multiple XMLs.
    Is the new BIP version available, or an enterprise version that I can use?
    Thanks in advance,

    Hi Rich,
    Even i had a similar kind of problem. I wanted to fetch data from BI through the XMLA Connector which are created in Query Designer and then i wanted to fetch these fields and rearrange them and put it in a report format by colouring certain fields. Can the same can be done in WebDynpro.

Maybe you are looking for