High CPU when tranferring data between VLANs on the same subinterface
Hi
i have Cisco 2821 with 2 subinterfaces on the G0/0, with 2 different VLANs on them.
When i copy about 60 Mb/s between them, the CPU usage increase to 80-90 %, and start to drop the packets.
The CEF is on on all those subinterfaces.
Any recommendations ?
many thanks
Here is the info about those subinterfaces:
#sh cef interface g0/0.10
GigabitEthernet0/0.10 is up (if_number 5)
Corresponding hwidb fast_if_number 21
Corresponding hwidb firstsw->if_number 2
ICMP redirects are always sent
Per packet load-sharing is disabled
IP unicast RPF check is disabled
Input features: Stateful Inspection, Virtual Fragment Reassembly, Virtual Fragment Reassembly After
Output features: Stateful Inspection, TCP Adjust MSS
IP policy routing is disabled
BGP based policy accounting on input is disabled
BGP based policy accounting on output is disabled
Hardware idb is GigabitEthernet0/0
Fast switching type 1, interface type 27
IP CEF switching enabled
IP CEF switching turbo vector
IP prefix lookup IPv4 mtrie 8-8-8-8 optimized
Input fast flags 0x400061, Output fast flags 0x10181
ifindex 2(2)
Slot Slot unit 0 VC -1
IP MTU 1500
#sh cef interface g0/0.117
GigabitEthernet0/0.117 is up (if_number 21)
Corresponding hwidb fast_if_number 5
Corresponding hwidb firstsw->if_number 2
ICMP redirects are always sent
Per packet load-sharing is disabled
IP unicast RPF check is disabled
Input features: Stateful Inspection, Virtual Fragment Reassembly, Virtual Fragment Reassembly After
Output features: Stateful Inspection
IP policy routing is disabled
BGP based policy accounting on input is disabled
BGP based policy accounting on output is disabled
Hardware idb is GigabitEthernet0/0
Fast switching type 1, interface type 27
IP CEF switching enabled
IP CEF switching turbo vector
IP prefix lookup IPv4 mtrie 8-8-8-8 optimized
Input fast flags 0x400061, Output fast flags 0x10181
ifindex 2(2)
Slot Slot unit 0 VC -1
IP MTU 1500
sh int g0/0 st
GigabitEthernet0/0
Switching path Pkts In Chars In Pkts Out Chars Out
Processor 13584490 436643191 27043759 2436202283
Route cache 70111252 1482061430 60433310 610254739
Total 83695742 1918704621 87477069 3046457022
Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Recommendation? Yes, you may need a faster router. At 60 Mbps, you might be bumping into the capacity limitations of the 2821.
Similar Messages
-
My macbook pro i7 (2011 version) has a loud fan and a high cpu % when I have Skype on or when I am on Safari. My laptop would sometimes freeze for a while and it is usually hot. Has anyone else encounter this problem and know how to fix it? Thanks!
Skype is a very resource intensive activity...it has been reported on here users are seeing cpu temperatures on the order of 80-85 °C, within the limits of the cpu, but still hot to the touch.
Make sure nothing else is running so you keep the thermal load down. -
After installing Office 2013 Pro Plus on our XenApp 6.5 environment we noticed a drop in performance. Using taskmanager we could see winword.exe hit 20+% CPU usage when filling just 1 line with the same letter.
Some investigating lead us to the "Publish as PDF or XPS button", when it is added to the quick access toolbar the cpu usage doubles during keystrokes. Using procmon I noticed excessive registry reading, up to 150,000 lines in 10 seconds.
It seems to be a constant loop of the same queries to approx. 100 components in HKLM\Software\Microsoft\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\
I reproduced this in 3 different setups:
Win2008R2 + Office2013 Pro Plus 32-bit + Office 2013 updates until 12-nov 2014
Win 8.1 Laptop + Office2013 Pro Plus 32-bit + Office 2013 updates until 05-jan 2015
Win 8.1 Desktop + Office2013 Pro Plus 64-bit + Office 2013 updates until 17-dec 2014
Can anyone verify this behaviour? For now we've removed the shortcut from the quick access toolbar in our environment.
Here's a small portion of the queries.
19:22:49,7117781 WINWORD.EXE 1484 RegQueryKey HKLM SUCCESS Query: HandleTags, HandleTags: 0x0
19:22:49,7117861 WINWORD.EXE 1484 RegOpenKey HKLM\Software\Microsoft\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\1A89310DF62F54544A1465F790A7757D SUCCESS Desired Access: Read
19:22:49,7117969 WINWORD.EXE 1484 RegQueryValue HKLM\SOFTWARE\MICROSOFT\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\1A89310DF62F54544A1465F790A7757D\00005109110000000100000000F01FEC SUCCESS Type: REG_SZ, Length: 130, Data: C:\?Program Files\Common
Files\Microsoft Shared\OFFICE15\MSO.DLL
19:22:49,7118058 WINWORD.EXE 1484 RegCloseKey HKLM\SOFTWARE\MICROSOFT\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\1A89310DF62F54544A1465F790A7757D SUCCESS
19:22:49,7118154 WINWORD.EXE 1484 RegQueryKey HKLM SUCCESS Query: HandleTags, HandleTags: 0x0
19:22:49,7118232 WINWORD.EXE 1484 RegOpenKey HKLM\Software\Microsoft\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\837CF31208764B643868B58117357D20 SUCCESS Desired Access: Read
19:22:49,7118332 WINWORD.EXE 1484 RegQueryValue HKLM\SOFTWARE\MICROSOFT\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\837CF31208764B643868B58117357D20\00005109110000000100000000F01FEC SUCCESS Type: REG_SZ, Length: 112, Data: C:\Program Files\Microsoft
Office\Office15\OUTLFLTR.DLL
19:22:49,7118415 WINWORD.EXE 1484 RegCloseKey HKLM\SOFTWARE\MICROSOFT\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\837CF31208764B643868B58117357D20 SUCCESS
19:22:49,7118511 WINWORD.EXE 1484 RegQueryKey HKLM SUCCESS Query: HandleTags, HandleTags: 0x0
19:22:49,7118586 WINWORD.EXE 1484 RegOpenKey HKLM\Software\Microsoft\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\FDFFB7C3B3B7DA048B21B3A72D1BF855 SUCCESS Desired Access: Read
19:22:49,7118694 WINWORD.EXE 1484 RegQueryValue HKLM\SOFTWARE\MICROSOFT\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\FDFFB7C3B3B7DA048B21B3A72D1BF855\00005109110000000100000000F01FEC BUFFER OVERFLOW Length: 144
19:22:49,7118769 WINWORD.EXE 1484 RegQueryValue HKLM\SOFTWARE\MICROSOFT\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\FDFFB7C3B3B7DA048B21B3A72D1BF855\00005109110000000100000000F01FEC SUCCESS Type: REG_SZ, Length: 134, Data: C:\Program Files\Common
Files\Microsoft Shared\OFFICE15\FLTLDR.EXE
19:22:49,7118849 WINWORD.EXE 1484 RegCloseKey HKLM\SOFTWARE\MICROSOFT\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\FDFFB7C3B3B7DA048B21B3A72D1BF855 SUCCESS
19:22:49,7118949 WINWORD.EXE 1484 RegQueryKey HKLM SUCCESS Query: HandleTags, HandleTags: 0x0
19:22:49,7119023 WINWORD.EXE 1484 RegOpenKey HKLM\Software\Microsoft\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\BF574A30F66E6D54186C7F15B116E7A3 SUCCESS Desired Access: Read
19:22:49,7119123 WINWORD.EXE 1484 RegQueryValue HKLM\SOFTWARE\MICROSOFT\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\BF574A30F66E6D54186C7F15B116E7A3\00005109110000000100000000F01FEC SUCCESS Type: REG_SZ, Length: 100, Data: 20:\CLSID\{000C0126-0000-0000-C000-000000000046}\
19:22:49,7119203 WINWORD.EXE 1484 RegCloseKey HKLM\SOFTWARE\MICROSOFT\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\BF574A30F66E6D54186C7F15B116E7A3 SUCCESS
19:22:49,7119295 WINWORD.EXE 1484 RegQueryKey HKLM SUCCESS Query: HandleTags, HandleTags: 0x0
19:22:49,7119369 WINWORD.EXE 1484 RegOpenKey HKLM\Software\Microsoft\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\017CCC9DE12773C4FAD559D2951B14C6 SUCCESS Desired Access: Read
19:22:49,7119466 WINWORD.EXE 1484 RegQueryValue HKLM\SOFTWARE\MICROSOFT\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\017CCC9DE12773C4FAD559D2951B14C6\00005109110000000100000000F01FEC SUCCESS Type: REG_SZ, Length: 128, Data: 22:\Software\Microsoft\Office\15.0\User
Settings\Mso_Core\Count
19:22:49,7119544 WINWORD.EXE 1484 RegCloseKey HKLM\SOFTWARE\MICROSOFT\Windows\CurrentVersion\Installer\UserData\S-1-5-18\Components\017CCC9DE12773C4FAD559D2951B14C6 SUCCESSI'll do that, I'm however still interested if somebody can confirm the excessive registry queries.
As a brief test, I captured winword.exe (2013) registry-reads on my Win8.1 pc (64bit Windows), with ProcMon.
this is over a capture period of less than one second
2092 of 2352 contain "component" in the reg path
this is when I have winword open and whilst "File, Export" is displayed (this is what offers the export-to-PDF option)
vs. 168 registry operations in an interval of 10 seconds, by winword.exe, if word is simply "running in background with an open blank document"
I'm not sure if that is useful, but it seems an awful lot of registry reads/writes from an application which isn't apparently doing anything at the time..
EDIT: similar registry read/write rate, when save-as-pdf is added to QAT (again sitting idle on a blank document). the registry read/write rate drops back down to 160 if the save-as-pdf feature is then removed from QAT.
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!) -
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .
HI All,
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.235.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... WLAN Controller 5508
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.125.18.15
Last Reset....................................... Software reset
System Up Time................................... 41 days 5 hrs 14 mins 42 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... US - United States
--More or (q)uit current module or <ctrl-z> to abort
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +20 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 10
Number of Active Clients......................... 61
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
AP Bundle Information
Primary AP Image Size
ap3g1 5804
ap801 5192
ap802 5232
c1100 3096
c1130 4972
c1140 4992
c1200 3364
c1240 4812
c1250 5512
c1310 3136
c1520 6412
c3201 4324
c602i 3716
Secondary AP Image Size
ap801 4964
c1100 3036
--More or (q)uit current module or <ctrl-z> to abort
c1130 4884
c1140 4492
c1200 3316
c1240 4712
c1250 5064
c1310 3084
c1520 5244
c3201 4264
Press Enter to continue or <ctrl-z> to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or <ctrl-z> to abort
Network Information
RF-Network Name............................. OGR
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
--More or (q)uit current module or <ctrl-z> to abort
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Fast SSID Change ........................... Enabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or <ctrl-z> to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or <ctrl-z> to abort
AP Summary
Number of APs.................................... 8
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
KNOWLOGY_DC01 disabled -
KNOWLOGY_DC02 disabled -
--More or (q)uit current module or <ctrl-z> to abort
KN1252_AP01 disabled -
KN1252_AP02 disabled -
Anham_AP03 disabled -
ANHAM_AP01 disabled -
ANHAM_AP04 disabled -
ANHAM_AP02 disabled -
Press Enter to continue or <ctrl-z> to abort
AP Location
Total Number of AP Groups........................ 3
Site Name........................................ ANHAM8075
Site Description................................. ANHAM 8075 Location
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
Site Name........................................ Knowlogy_DC
--More or (q)uit current module or <ctrl-z> to abort
Site Description................................. DC Center Access points
WLAN ID Interface Network Admission Control Radio Policy
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
Site Name........................................ OGR
Site Description................................. 1934 OGR Office
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
7 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Site Name........................................ default-group
Site Description................................. <none>
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
5 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
9 knowlogy_ogr Disabled None
10 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Press Enter to continue or <ctrl-z> to abort
AP Config
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch IP Address.................. 10.125.18.15
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
--More or (q)uit current module or <ctrl-z> to abort
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or <ctrl-z> to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 44
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
--More or (q)uit current module or <ctrl-z> to abort
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
--More or (q)uit current module or <ctrl-z> to abort
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or <ctrl-z> to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... KN1252_AP01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:ef:06:50
IP Address Configuration......................... DHCP
IP Address....................................... 10.125.18.101
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.125.18.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ Knowlogy Conference Rooms Side
Cisco AP Group Name.............................. OGR
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.4.10.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. PoE/Medium Power (15.4 W)
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1252AG-A-K9
AP Image......................................... C1250-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX122990L5
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 118
WLAN 1 :........................................ 111
WLAN 2 :........................................ 111
WLAN 4 :........................................ 112
WLAN 6 :........................................ 112
WLAN 7 :........................................ 111
WLAN 9 :........................................ 112
WLAN 8 :........................................ 112
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 26 days, 00 h 24 m 39 s
--More or (q)uit current module or <ctrl-z> to abort
AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
Join Date and Time............................... Wed Oct 9 10:59:07 2013
Join Taken Time.................................. 0 days, 00 h 00 m 50 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 7
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:df:a5:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 ..........Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
Sent from Cisco Technical Support iPhone App -
Hi!
I apologize for how crazy my question sounds,, (& for everything that follows), but I'm at a loss as to the correct wording...I hope my explanation will clarify things, at least enough so that someone understands what I'm trying to say! Wish me luck!
I'm using Firefox 37.0.1 on Windows 8.1 & everything is up to date. The most important details for this problem will be my settings & addons for Firefox, so here goes:
I allow all cookies, but it's set to clear them when Firefox closes.
I do NOT save any history or passwords & I also have "Click & Clean" enabled, & I use it frequently, even though I don't save any history or anything else, just to add to my security/privacy, (guess I didn't use it often enough, huh?)
I have the box checked for "Do Not Track", (but I just learned the hard way that even so-called "nice" companies don't honor this request)
I have "Ghostery" as well as "Google Analytics Opt-out" enabled, (even though I don't use Google for my search engine, nor do I go to a Google site unless it's absolutely necessary, (I read about Google's penchant for following users everywhere in order to get their preferences, so I avoid them if at all possible).
In other words, I thought I was protected from tracking-related problems, but I need to know if these precautions are effective when using Firefox & having several tabs open...then opening another tab/window...are cookies & any other info "readable", (I don't know what word should be used here), from tab to tab in the same window, (which just happened to me), & is the cookie info readable from window to window? In other words, do I have to completely close out Firefox, delete cookies, then open a brand new window so that any session cookie info has been deleted to protect my browsing info from being accessed?
I know, I'm STILL not making much sense...here's what happened, (I won't divulge the site that did the 'cookie abuse', though.
I had several tabs open, as I usually do, because I was gathering info for research on a report I was working on. Suddenly, I remembered I had to order my hubby's birthday gift, so I opened another tab, (in the same window), to my favorite site & started searching for the items I wanted. I found what I was looking for & was getting ready to check out when I noticed something very odd...there were several "suggestions" listed for items I "might be interested in, based on my browsing", but the funny thing was, I didn't search for anything related to these suggested items! Instead, they were related to items in the other tabs I had open. Scary, underhanded stuff, if you ask me! I always knew not to have banking/financial sites open while surfing, but the tabs I had open were from sites where I was getting research info for my report, so no red flags went up when I went to the site to place my order.
So I guess the question I need answered is...is cookie info accessible only between tabs in the same browser window OR is it even accessible from window to window? Did I make sense yet? I sure hope so, because this incident has me absolutely flapping around like a fish that's just been pulled out of the water & is just left on the deck! This obvious assault on my privacy has hit me like a punch in the stomach, because I thought this site was one I could trust...especially since I had "Do Not Track", "Google Analytics Opt-out" & "Ghostery" enabled!
I just don't know how to deal with this, but obviously, I need to know the rules so this NEVER happens again. Luckily, there wasn't any finance-related breach, but my sense of trust has taken a BIG blow.
If this made sense to anyone, please advise me on the rules of 'cookie abuse' so I don't EVER let this happen again!
Also, is cookie info able to be shared between browsers, e.g. use Firefox for more personal/sensitive browsing & Opera for research activity?
Any & all advice is desperately needed & gratefully accepted! I sincerely hope this doesn't happen to anyone else because it really takes the wind out of your trust bubble. I've never been as surprised & disappointed at a company as I am about this. So sad.
Oh well, learn something new every day...too bad I learned not to trust. :(
Thanks in advance for your help.
Nuts4Mutts :(
P.S. If you need anything clarified, just askCookies are stored in a cookie jar and thus are shared among all open tabs and windows.
Only all Private Browsing mode tabs/windows use a separate cookie jar that is used for all PB mode tabs.
Note that session restore stores cookies of open tabs in the sessionstore.js file as part of stored session data.
* http://kb.mozillazine.org/browser.sessionstore.privacy_level -
It is possible to charge an iPad3 over USB and transmit data over USB at the same time?
Hello,
it is possible to charge an iPad3 over USB and transmit data over USB at the same time?
If yes, how?
Thanks
Best regardsOK!?
That is right that the USB data oins are not connected to +5V pin.
But i found a description for a self built power supply for iPad.
http://timothyb.net/DIY_iPad_2_USB_Charger.html
and
https://www.mikrocontroller.net/topic/262610?goto=2726627#2726627
The description say: data pin D- need a voltage level of 2V and D+ 2,857V
when the data pins have this special voltage levels and VCC has +5V only then the iPad is charging.
The voltage "D+/D- coding" is the key for the iPad to charge.
OK now back to my problem.
The regular USB data pin voltage level is 0,3 - 3.,0 voltage. When the iPad is charging the data pins have this special voltage level. Now i try to transmit data over the usb data pins with the. Normaly the USB port transmit the data with a voltage level of max. 3V.
And here my problem. The higher voltage level at the data pins cares therefor that the iPad stop the charging.
Is that correct? -
MM STO between Plants under the same company code
Hi experts,
Please guide on the configuration steps for doing STO between Plants unders the same company code.
We have company code 100 in that Plants A B & C are theie. Each Plant can do STO to other Plant.
How to configure this scenario?Dear,
Please follow bellow path
1. Create a vendor for the Company code of the receiving plant using account group 0007 via T-Code XK01.
2. In the purchasing data view assign the supplying plant and the schema group
3. Create customer with the sales area of the vendor.
4. The shipping conditions, the delivering plant and the transportation zone determine the route in the STO.
5. In the pricing procedure determination relevant to the STO assign document pricing procedure and customer pricing procedure to get the pricing in the invoice.
6. Maintain condition records for pricing condition.
7. Maintain carrier as a partner in the customer master.
8. In OMGN select the supplying plant and assign the company code and sales area. Similarly select the receiving plant and assign the company code and sales area (The company code to which the plant is assigned to).
9. Assign the delivery type and checking rule to the document type.
10. And finally, assign the purchasing document type to the supplying plant and the receiving plant.
11. Create the STO using T-Code ME 21N and save.
12. Check for release strategy if any and release using T-Code ME 28.
13. Create delivery in background using VL10G.
14. If delivery is created, it is an indication of correct configuration and master data creation.
Stock transfer between two plants in different company codes is known as inter company stock transfer.
Material should be maintained in both supplying and receiving plant MM01
Stock should maintain only in supplying plant MB1C
Create receiving plant as a customer in supplying plants company code and sales area XD01
Assign this customer number in receiving plant details OMGN
Assign supplying sales area in supplying plant details OMGN
Assign delivery type NB for in combination of supplying/ receiving plants.
Create STO ME21N
As it is normal there in the item details we should get shipping date i.e. customer number
Go for Delivery VL10B
Shipping point *****
Select PO go for execute
then select the delivery then go for delvy ............create delvy,,,, delvy number generated.
Goods Issue VL02
Delvy doc **********
Click on picking
enter the picking qty
Click on PGI
in the mean time check in the PO history you will get the details
Goods receipt MIGO
Stock transfers that include deliveries and billing documents/invoices are only possible between plants belonging to different company codes.
If you want to carry out a cross-company-code stock transport order with delivery but without a billing document, you must set the Relevant for Billing (data element FKREL) indicator in Customizing of the item type to "blank" (Not relevant for billing).
The following applications are involved in this type of stock transfer:
? Purchasing (MM-PUR) in entering the order
? Shipping (LE-SHP) in making the delivery from the issuing plant
? Billing (SD-BIL) in creating the billing document for the delivery
? Inventory Management (MM-IM) at goods receipt in the receiving plant
Invoice Verification (MM-IV) at invoice receipt in the receiving
Transfer of goods from one location to another location, it may be between plants within the same company code or in different company code's plants.
within the company code, but plants,
receiving plant will raise the STO in Supplying/issuing plant-ME21n,
Supplying plant will deliver the goods to receiving plants ,
then we need to pick n post the Goods Issue-VL02n,
now when we can observe that the STO qty will be added into receiving plant and reduced in Delivering plant,
To do this, we need do prior customization in SPRO-IMG,-
material should be created in both plants( receiving & Supplying)
-maintain the stock only in supplying plant
-create a dummy customer in supplying plant's sales area(if u have one sales area, create in tat comp code n sales area)
-assign this customer number to receiving plant's details along with the sales area,
-Assign the STO doc type(UB) to Supplying plant, along with checking rule
-Assign the Del type (NL/NLCC) to Supplying n receiving plant.
Stock Transport Order:
http://help.sap.com/saphelp_47x200/helpdata/en/4d/2b911d43ad11d189410000e829fbbd/content.htm
http://help.sap.com/saphelp_47x200/helpdata/en/4d/2b917843ad11d189410000e829fbbd/content.htm
http://help.sap.com/saphelp_47x200/helpdata/en/4d/2b918543ad11d189410000e829fbbd/content.htm
u can also use the SAP building block
with delivery
http://help.sap.com/bestpractices/BBLibrary/html/P36_IntStockTransDel_EN_IN.htm
without delivery
http://help.sap.com/bestpractices/BBLibrary/html/P38_IntStockTransWithoutDel_EN_IN.htm
Regards,
Mahesh Wagh -
Move an iTunes library between users on the same mac
How do I move an iTunes library between users on the same mac?
I accidentally created a secondary user on my mac some time ago when using the migration tool and am now going back and transferring all my files from the secondary to the admin user profile.
I wanted to know which itunes files/folders need to be copied over.
Is the process as simple as replacing the itunes folder on admin with the copied itunes folder from my secondary profile or do I need to delete the admin folder first and then copy the old folder over or do I delete the contents of the folder and replace with the copied contents?
I am using shared folders to move between users, but want to make sure that I am picking the right files to transfer.
Thanks in advance.Assuming you have left iTunes to default settings so everything is still in the iTunes folder the way iTunes likes it to be, copy the whole of the iTunes folder to the new location. If it is in the default directory (Home > Music) for iTunes the application will automatically use it there for the new account. If you put it elsewhere you will have to start iTunes and immediately hold down the option key to direct it to the new location.
It is just possible you will have to change permissions. If you encounter those issues read the part about changing permissions on the iTunes folder in: https://discussions.apple.com/message/11583914
This is all a slight variant on: iTunes: How to move [or copy] your music to a new computer [or another drive] - http://support.apple.com/kb/HT4527 -
VBA Merge PDFs - Error when first and second PDF are the same
Using http://khkonsulting.com/2009/03/adobe-acrobat-and-vba-an-introduction/ as a guide, I am able to successfully merge multiple pdf's together into one document using VBA (Access mdb), except when the PDF being merged to has the same name as the next PDF.
Here's my scenario. An Access table is updated with a list of reports that need to be printed. All of these reports are PDF's. I loop thru this table and merge the PDF's according to an identifier, then print the group. There are times
when there are multiple copies of the same report for an identifier. If the PDF being merged to has the same name of the PDF being merged, an error occurs. How can I handle this situation?
Sample data: This identifier (ESO and Pulling) needs to merge these PDF's (Aaa.PDF) together which happen to have the same name. Aaa.PDF is trying to merge Aaa.PDF and this throws an error.
Aaa.PDF ESO Pulling
Aaa.PDF ESO Pulling
This identifier merges fine despite having the same PDF twice. But the first PDF is not named the same. Xxx.PDF is the first PDF and merges the next two into it. The last two
are named the same.
Xxx.PDF 916 Pulling
Bbb.PDF 916 Pulling
Bbb.PDF 916 Pulling
Code:
pdfDoc1.Open (filesToMerge(1))
numPages = pdfDoc1.GetNumPages()
Set pdfDoc2 = CreateObject("AcroExch.PDDoc")
Dim i As Integer
For i = 2 To intNbr - 1
pdfDoc2.Open (filesToMerge(i))
If pdfDoc1.InsertPages(numPages - 1, pdfDoc2, 0, pdfDoc2.GetNumPages(), True) = False Then
MsgBox "Cannot insert pages"
End If
pdfDoc2.Close
Next i
If pdfDoc1.Save(PDSaveFull, "C:\....\ReportPacket__" & Trim(CStr(intReportCount)) & "__" & ... & ".pdf") = False Then
MsgBox "Cannot save the modified document"
End If
pdfDoc1.Close
The pdfDoc1.InsertPages command fails, displays "Cannot insert pages", then displays "Method 'Close' of object 'CAccroPDDoc' failed.
Thanks for any help or advice.Hi
As far as I know, Access didn't provide such method. But I think you are able to achieve this goal through some 3rd party PDF component
Hope this will help you.
Best Regards
Lan
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey. -
I cannot use data and voice at the same time.
I cannot use data and voice at the same time.
I am on Wifi (connected) and at the same time I am on a voice call. when I switch to my RSS feed reader it does not sync it comes out with a message cannot connect to internet, I thought it is a problem with the feed reader application, IE 10 behaves the same I cannot browse when I am on a voice call.
This is a very basic issue, am I missing something? Please help.
My Model is lumia 820 with the latest portico update.
TIA
SandeepI am aware that packet data via EDGE and voice cannot happen at the same time, surprisingly when I am on voice call I cannot connect to internet via Wifi too
-
No ping between host in the same subnet
Hello,
I have a question about the ASA and the ARP traffic in IOS 9.1.2 for ASA 5585-X and multicontext. I have discovered a curious behaviour about the traffic ARP in the my CLUSTER of ASA's. When I try to send a ping between host in the same subnet and these host have as Gateway the interface of the ASA (ASA is his router) don't works, if I mark the check to enable the comunications between host connected to the same interface this cotinues without work. The only way to get my aim (ping between host), I need to implement and Access Rule allowing the traffic IP between my origin network and destination the same network.
I think that this is some feature of ASA that filter the ARP Request but I don't understand!!! Can I help me, please?
Thanks.Hi,
Your firewall should not see any traffic between the hosts on the same subnet.
If it is seeing traffic between the hosts then its likely that Proxy ARP on the ASA is the problem. Proxy ARP is enabled on the ASA by default on all interfaces. This essentially means that when the host connecting to the other host on the same subnet sends an ARP request the ASA might reply to that ARP request instead of the actual destination host. This is why traffic might get forwarded to the ASA instead of the actual host.
If you want to disable the Proxy ARP on some ASA interface then you can use
sysopt norpoxyarp
Where you replace the with the actual name you have given to the interface on the ASA. This disables the Proxy ARP
- Jouni -
WebI:Creating a minus query from data providers not using the same universe
Hi there. A client of ours wishes to use Combined Query on multiple universes in the same WebI report. So far, I have heard it is not feasible in WebI. I know it is possible in DeskI. Even the sub-query option is limited to just one universe in WebI. So, I am stuck.
Is there a workaround to creating a minus query from data providers not using the same universe in WebI?Hello Amit,
what are the Datasources ? Usually when you create a Sub Query you can choose a seperate Universe.
Maybe if you only see one Universe you only have the rights for this Universe ?!.
Regards
-Seb. -
Is it possible to reuse views between components of the same project ?
Hello All,
Does anyone knows if its possible to re-use views/viewsets which maybe common between components within the same project ? I am trying to use back common views where possible so that it will be easier to maintain the application should there be changes in the future. Having identical views across the components will mean that there is a need to maintain muliples views when updating/amending. Any help or suggestion will be greatly appreciated. Thank you.
from
Kwok WeiThank you very much Bharathwaj. I am not very keen in using JDI (lack of usage knowledge + current project to small to use JDI + insufficient time) and hence I guess I will need to continue to look around for another solution.
Any experts who may have more suggestions kindly put then up here please. Thank you.
from
Kwok Wei -
I have installed iOS7 on my iPhone4. I am able to add/edit contacts by clicking the "contact" icon. But when I am trying to do the same after clicking the "phone" icon, it is not displaying the keypad. I believe it is a bug in iOS7.
Please confirm.
iPhone 4, iOS 7Hello jayanand,
You may need to force close all open apps, then restart the phone. If necessary, you may need to reset the phone after that.
iOS: Force an app to close
http://support.apple.com/kb/HT5137
iPhone, iPad, iPod touch: Turning off and on (restarting) and resetting
http://support.apple.com/kb/HT1430
Cheers,
Allen -
Share calendar between users on the SAME mac
How can I share a single calendar (and address book) between users on the SAME mac? Thanks.
I've got the same question...
Anyone?
Anyone?
...bump...
Maybe you are looking for
-
At my wits end... IMac shuts down or cannot turn on montior
My IMac randomly shuts down. I have the energy saver set for computer to sleep after 1 hour. I have not installed any new software. This problem began about a month ago. I have to use the restart button and always get an error (posted below), that th
-
Convert Photoshop Elements 7 for Windows to a Mac version?
I have Photoshop Elements 7 for Windows and just got a Mac. I was wondering if Adobe would convert Elements to a Mac version for a fee. Anyone had experience with that? Thanks. tialldplucy
-
Yet another version of iTunes (11.0.3) and still there is no cover flow function available. I find it almost unreal how Apples developers can take away such an important functionality - to obviously many users - and persist to do so, release after re
-
Why is my ipad 3 suddenly shut down?
Im just playing temple run whhen suddenly it shuts down,all i can see is the apple logo
-
RV320: Need to use as gateway for multiple subnets
We just purchased an RV320 as a replacement/upgrade to an RV042. Our Internet connection was upgraded to 200Mbps and the RV042 wouldn't handle that throughput. Our internal network has 4 subnets, all connected via a layer 3 switch. The RV320 is conne