Hostname change: Failed to contact DSCC registry
Dear all,
we have installed ODSEE 11.1.1.5 under Solaris x86 10 08/11 successfully
ie were able to log into DSCC as Directory Service Manager.
After changing the system's hostname from OLD to NEW we can't now use
the DSCC again because there is this message after putting in the directory service
password:
Failed to contact DSCC regisrty. Make sure that the DSCC registry is online and
listening on ldap://*OLD*:3998
How can we arrange it that the registry is listening now to ..//_NEW_:3998?
Should we use 'dsccsetup dismantle/initialize?
Many thanks in advance for any hint!
Rainer
1) "dsconf export -p 3998 -c cn=dscc /your_DSEE_INSTALL_PATH/var/dcc/ads/ldif/export.ldif" or something like that will do the job. You can also use "dsadm export" with a slightly different syntax. The main difference is that dsconf works offline I believe, so you need to stop the DSCC registry before.
2) Edit the LDIF export and remove the unwanted entries. Since you'll have to dismantle/reinitialize the DSCC registry, there's no need to keep the DSCC registry up. Moreover, you can safely stop it without any impact on your existing DS servers. The DSCC is just required for some dsadm/dpadm/dsconf/dpconf/dsccsetup commands and the GUI, but it's not a requirement at all to run your DS instances.
Similar Messages
-
DFSR failed to contact domain controller
Im having an odd problem with DFSR group we created to replicate web content between two of our web servers.
In event viewer we have this event 1202 for DFSR.
"The DFS Replication service failed to contact domain controller to access configuration information. Replication is stopped. The service will try again during the next configuration polling cycle, which will occur in 60 minutes. This event can
be caused by TCP/IP connectivity, firewall, Active Directory Domain Services, or DNS issues.
Additional Information:
Error: 160 (One or more arguments are not correct.)"
In the DFSR logs I see this.
20140303 12:18:27.874 1404 CFAD 8300 Config::AdConfig::GetLocalComputerNameWithDns Computer's fully-qualified DNS name: DFSRSERVER.domain.tld
20140303 12:18:27.920 1404 CFAD 311 Config::AdConnection::Connect Binding to dcAddr:\\1.1.1.1 dcDnsName:\\MYDC.domain.tld
20140303 12:18:27.936 1404 CFAD 143 Config::AdConnection::BindToAd Trying to connect. hostName:MYDC.domain.tld
20140303 12:18:28.467 1404 CFAD 162 Config::AdConnection::BindToAd Bound. hostName:MYDC.domain.tld
20140303 12:18:28.467 1404 CFAD 199 Config::AdConnection::BindToDc Try to bind. hostName:\\MYDC.domain.tld domainName:<null>
20140303 12:18:28.514 1404 CFAD 3373 [ERROR] Config::DsSession::Bind Failed to DsBind(). dc:\\MYDC.domain.tld domainName:<null> Error:5
20140303 12:18:28.514 1404 CFAD 215 Config::AdConnection::BindToDc (Ignored) Failed to bind. hostName:\\MYDC.domain.tld domainName:<null> Error:[Error:5(0x5) Config::DsSession::Bind ad.cpp:3380 1404 W Access is denied.]
20140303 12:18:28.514 1404 CFAD 199 Config::AdConnection::BindToDc Try to bind. hostName:\\1.1.1.1 domainName:<null>
20140303 12:18:28.514 1404 CFAD 3373 [ERROR] Config::DsSession::Bind Failed to DsBind(). dc:\\1.1.1.1 domainName:<null> Error:87
20140303 12:18:28.514 1404 CFAD 215 Config::AdConnection::BindToDc (Ignored) Failed to bind. hostName:\\1.1.1.1 domainName:<null> Error:[Error:87(0x57) Config::DsSession::Bind ad.cpp:3380 1404 W The parameter is incorrect.]
20140303 12:18:28.514 1404 SCFS 150 [WARN] ServiceConfig::DsPollIsDue Failed to enable lightweight polling. Error:
+ [Error:160(0xa0) Config::AdConfig::ConnectToLocalDc ad.cpp:8365 1404 W One or more arguments are not correct.]
+ [Error:160(0xa0) Config::AdConfig::Connect ad.cpp:8113 1404 W One or more arguments are not correct.]
+ [Error:160(0xa0) Config::AdConnection::Connect adconnection.cpp:377 1404 W One or more arguments are not correct.]
+ [Error:160(0xa0) Config::AdConnection::BindToDc adconnection.cpp:226 1404 W One or more arguments are not correct.]
20140303 12:18:28.514 1404 CREG 1419 Config::RegReader::IsSysVolCommitFlagSet key: System\CurrentControlSet\Services\DFSR\Parameters\SysVols\Demoting SysVols valueName:'SysVol Information is Committed' result:0
20140303 12:18:28.514 1404 W2CH 266 ConfigurationHelper::PollAdConfigNow Trying to connect to AD
20140303 12:18:28.514 1404 CFAD 311 Config::AdConnection::Connect Binding to dcAddr:\\1.1.1.1 dcDnsName:\\MYDC.domain.tld
20140303 12:18:28.514 1404 CFAD 143 Config::AdConnection::BindToAd Trying to connect. hostName:MYDC.domain.tld
20140303 12:18:28.514 1404 CFAD 162 Config::AdConnection::BindToAd Bound. hostName:MYDC.domain.tld
20140303 12:18:28.514 1404 CFAD 199 Config::AdConnection::BindToDc Try to bind. hostName:\\MYDC.domain.tld domainName:<null>
20140303 12:18:28.514 1404 CFAD 3373 [ERROR] Config::DsSession::Bind Failed to DsBind(). dc:\\MYDC.domain.tld domainName:<null> Error:5
20140303 12:18:28.514 1404 CFAD 215 Config::AdConnection::BindToDc (Ignored) Failed to bind. hostName:\\MYDC.domain.tld domainName:<null> Error:[Error:5(0x5) Config::DsSession::Bind ad.cpp:3380 1404 W Access is denied.]
20140303 12:18:28.514 1404 CFAD 199 Config::AdConnection::BindToDc Try to bind. hostName:\\1.1.1.1 domainName:<null>
20140303 12:18:28.514 1404 CFAD 3373 [ERROR] Config::DsSession::Bind Failed to DsBind(). dc:\\1.1.1.1 domainName:<null> Error:87
20140303 12:18:28.514 1404 CFAD 215 Config::AdConnection::BindToDc (Ignored) Failed to bind. hostName:\\1.1.1.1 domainName:<null> Error:[Error:87(0x57) Config::DsSession::Bind ad.cpp:3380 1404 W The parameter is incorrect.]
20140303 12:18:28.514 1404 EVNT 1194 EventLog::Report Logging eventId:1202 parameterCount:4
20140303 12:18:28.514 1404 EVNT 1214 EventLog::Report eventId:1202 parameter1:
20140303 12:18:28.514 1404 EVNT 1214 EventLog::Report eventId:1202 parameter2:60
20140303 12:18:28.514 1404 EVNT 1214 EventLog::Report eventId:1202 parameter3:160
20140303 12:18:28.514 1404 EVNT 1214 EventLog::Report eventId:1202 parameter4:One or more arguments are not correct.
20140303 12:18:28.530 1404 W2CH 318 [ERROR] ConfigurationHelper::PollAdConfigNow (Ignored) Failed to connect to AD. Error:
+ [Error:160(0xa0) Config::AdConfig::ConnectToLocalDc ad.cpp:8365 1404 W One or more arguments are not correct.]
+ [Error:160(0xa0) Config::AdConfig::Connect ad.cpp:8113 1404 W One or more arguments are not correct.]
+ [Error:160(0xa0) Config::AdConnection::Connect adconnection.cpp:377 1404 W One or more arguments are not correct.]
+ [Error:160(0xa0) Config::AdConnection::BindToDc adconnection.cpp:226 1404 W One or more arguments are not correct.]
When I run "dfsrdiag pollad":
[ERROR] PollDsNow method executed unsuccessfully. ReturnValue: 12 (0xc)
[ERROR] Failed to execute PollAD command Err: -2147217407 (0x80041001)
However I can run "dfsrdiag dumpadcfg" and it outputs everything fine.
We don't have any other problems with AD. It seems like this started after we installed KB2467173 & KB2538242. We are going to uninstall those and see if it works.I can successfully run "dfsrdiag.exe dumpadcfg" and it outputs the entire config. Why does "dfsrdiag pollad" fail then if the config can be read.
Why did it work before I rebooted the server? In both cases it broke after rebooting.
PS C:\Windows\system32> dfsrdiag dumpadcfg
LDAP Bind : mydc.domain.tld
SitesDn : cn=sites,cn=configuration,dc=domain,dc=tld
ServicesDn : cn=services,cn=configuration,dc=domain,dc=tld
SystemDn : cn=system,dc=domain,dc=tld
DefaultNcDn : dc=domain,dc=tld
ComputersDn : cn=computers,dc=domain,dc=tld
DomainCtlDn : ou=domain controllers,dc=domain,dc=tld
SchemaDn : CN=Schema,CN=Configuration,dc=domain,dc=tld
COMPUTER: web1
DN : cn=web1,ou=web,ou=virtual servers,ou=servers,dc=domain,dc=tld
GUID : 152E849C-4D7B-4AE8-B034-83747DBC1E89
DNS : web1.domain.tld
Server Ref : (null)
USN Changed : 10862129
When Created : Friday, January 31, 2014 8:41:06 PM
When Changed : Tuesday, March 4, 2014 2:54:36 PM
LOCAL SETTINGS: DFSR-LOCALSETTINGS
DN : cn=dfsr-localsettings,cn=web1,ou=web,ou=virtual servers,ou=servers,dc=domain,dc=tld
GUID : 3FD696E7-6598-4CDB-B2AB-98F148C0D2F7
Version : 1.0.0.0
USN Changed : 10932017
When Created : Thursday, March 6, 2014 2:11:12 PM
When Changed : Thursday, March 6, 2014 2:15:25 PM
SUBSCRIBER: FF88A312-A0EB-44CC-A614-7A3D06DCC0AB
DN : cn=ff88a312-a0eb-44cc-a614-7a3d06dcc0ab,cn=dfsr-localsettings,cn=web1,ou=web,ou=virtual servers,ou=servers,dc=domain,dc=tld
GUID : 1119B663-F02A-4F1F-A904-23A87CFC93C3
Member Ref : cn=ff88a312-a0eb-44cc-a614-7a3d06dcc0ab,cn=topology,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
USN Changed : 10931931
When Created : Thursday, March 6, 2014 2:11:12 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
SUBSCRIPTION: 6783DDE1-C795-4E8B-B07D-4EA8D7D0317F
DN : cn=6783dde1-c795-4e8b-b07d-4ea8d7d0317f,cn=ff88a312-a0eb-44cc-a614-7a3d06dcc0ab,cn=dfsr-localsettings,cn=web1,ou=web,ou=virtual servers,ou=servers,dc=domain,dc=tld
GUID : 3737B1F2-7E38-47E2-90E7-E57D82B145F1
ContentSetGuid: 6783DDE1-C795-4E8B-B07D-4EA8D7D0317F
Root Path : c:\inetpub\internetsites
Root Size : 10240 (MB)
Staging Path : c:\inetpub\internetsites\dfsrprivate\staging
Staging Size : 4096 (MB)
Conflict Path : c:\inetpub\internetsites\dfsrprivate\conflictanddeleted
Conflict Size : 4096 (MB)
USN Changed : 10931919
When Created : Thursday, March 6, 2014 2:11:13 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
SUBSCRIPTION: F2F1F3A2-B36F-4170-B371-8E8043DF73F4
DN : cn=f2f1f3a2-b36f-4170-b371-8e8043df73f4,cn=ff88a312-a0eb-44cc-a614-7a3d06dcc0ab,cn=dfsr-localsettings,cn=web1,ou=web,ou=virtual servers,ou=servers,dc=domain,dc=tld
GUID : 57E7F8D7-1121-4334-BC81-74226ADF8969
ContentSetGuid: F2F1F3A2-B36F-4170-B371-8E8043DF73F4
Root Path : c:\internet_data
Root Size : 10240 (MB)
Staging Path : c:\internet_data\dfsrprivate\staging
Staging Size : 4096 (MB)
Conflict Path : c:\internet_data\dfsrprivate\conflictanddeleted
Conflict Size : 4096 (MB)
USN Changed : 10931921
When Created : Thursday, March 6, 2014 2:11:13 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
SUBSCRIPTION: D0438B52-B706-4E40-B4C3-FE7A1ACA5FCF
DN : cn=d0438b52-b706-4e40-b4c3-fe7a1aca5fcf,cn=ff88a312-a0eb-44cc-a614-7a3d06dcc0ab,cn=dfsr-localsettings,cn=web1,ou=web,ou=virtual servers,ou=servers,dc=domain,dc=tld
GUID : F8217091-F71A-4D4A-A676-097583171A63
ContentSetGuid: D0438B52-B706-4E40-B4C3-FE7A1ACA5FCF
Root Path : c:\php\phpsites
Root Size : 10240 (MB)
Staging Path : c:\php\phpsites\dfsrprivate\staging
Staging Size : 4096 (MB)
Conflict Path : c:\php\phpsites\dfsrprivate\conflictanddeleted
Conflict Size : 4096 (MB)
USN Changed : 10931923
When Created : Thursday, March 6, 2014 2:11:13 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
GLOBAL SETTINGS: DFSR-GLOBALSETTINGS
DN : cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
GUID : 2E98CE5E-5CC7-4322-B5EA-2B6B340C689F
USN Changed : 12525
When Created : Saturday, October 22, 2011 1:56:38 AM
When Changed : Saturday, October 22, 2011 1:56:38 AM
REPLICATION GROUP: WEB CONTENT
DN : cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
GUID : 9C94A417-6F6C-4F6C-BBFA-B8F52854C4DF
Type : 0 (UNKNOWN REPLICATION GROUP TYPE)
Options : 0x1 [Local Time Schedule]
USN Changed : 10931906
When Created : Thursday, March 6, 2014 2:11:12 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
CONTENT: CONTENT
DN : cn=content,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
GUID : 6714C533-E631-4E71-930D-E4934FB7BD7E
USN Changed : 10931908
When Created : Thursday, March 6, 2014 2:11:12 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
CONTENT SET: INTERNET_DATA
DN : cn=internet_data,cn=content,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
GUID : F2F1F3A2-B36F-4170-B371-8E8043DF73F4
File Filter : ~*, *.bak, *.tmp
Compression Excl : (null)
Dir Filter : (null)
USN Changed : 10931916
When Created : Thursday, March 6, 2014 2:11:13 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
CONTENT SET: INTERNETSITES
DN : cn=internetsites,cn=content,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
GUID : 6783DDE1-C795-4E8B-B07D-4EA8D7D0317F
File Filter : ~*, *.bak, *.tmp
Compression Excl : (null)
Dir Filter : (null)
USN Changed : 10931915
When Created : Thursday, March 6, 2014 2:11:13 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
CONTENT SET: PHPSITES
DN : cn=phpsites,cn=content,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
GUID : D0438B52-B706-4E40-B4C3-FE7A1ACA5FCF
File Filter : ~*, *.bak, *.tmp
Compression Excl : (null)
Dir Filter : (null)
USN Changed : 10931917
When Created : Thursday, March 6, 2014 2:11:13 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
TOPOLOGY: TOPOLOGY
DN : cn=topology,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
GUID : 16053002-7B99-4DA7-BFE5-2A6418040640
USN Changed : 10931907
When Created : Thursday, March 6, 2014 2:11:12 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
MEMBER: FF88A312-A0EB-44CC-A614-7A3D06DCC0AB
DN : cn=ff88a312-a0eb-44cc-a614-7a3d06dcc0ab,cn=topology,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
GUID : 75A99277-C401-409F-A32D-6D8EE18E5D0C
Server Ref : (null)
Computer Ref : cn=web1,ou=web,ou=virtual servers,ou=servers,dc=domain,dc=tld
Keywords : (null)
Computer DNS : web1.domain.tld
USN Changed : 10931933
When Created : Thursday, March 6, 2014 2:11:12 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
CXTION: 9ECE3EB7-FE97-4A1B-8DE3-47A77B2C625B
DN : cn=9ece3eb7-fe97-4a1b-8de3-47a77b2c625b,cn=ff88a312-a0eb-44cc-a614-7a3d06dcc0ab,cn=topology,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
GUID : 1D26B348-3875-4BD1-9473-E72506AFA222
Inbound : true
Partner DN : cn=46f913db-8509-4581-a66d-d37e4ea3ef29,cn=topology,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
Enabled : TRUE
Options : 0x1 [Local Time Schedule]
USN Changed : 10931924
When Created : Thursday, March 6, 2014 2:11:13 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
CXTION: 2BFA8BE2-0444-4AAF-8293-A5486CF8D7A3
DN : cn=2bfa8be2-0444-4aaf-8293-a5486cf8d7a3,cn=46f913db-8509-4581-a66d-d37e4ea3ef29,cn=topology,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
GUID : A7203451-D95F-44D5-AC04-13056DCE5A89
Inbound : false
Partner DN : cn=46f913db-8509-4581-a66d-d37e4ea3ef29,cn=topology,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
Enabled : TRUE
Options : 0x1 [Local Time Schedule]
USN Changed : 10931925
When Created : Thursday, March 6, 2014 2:11:13 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
MEMBER: 46F913DB-8509-4581-A66D-D37E4EA3EF29
DN : cn=46f913db-8509-4581-a66d-d37e4ea3ef29,cn=topology,cn=web content,cn=dfsr-globalsettings,cn=system,dc=domain,dc=tld
GUID : 1BA26D07-45F5-44A0-8450-9274AFD99B1C
Server Ref : (null)
Computer Ref : cn=fccu01web,ou=web,ou=virtual servers,ou=servers,dc=domain,dc=tld
Keywords : (null)
Computer DNS : fccu01web.domain.tld
USN Changed : 10931927
When Created : Thursday, March 6, 2014 2:11:12 PM
When Changed : Thursday, March 6, 2014 2:11:27 PM
Operation Succeeded -
Dear All,
Our SAP Servers use Linux Suse 11 for OS with DB2 v10.1.0.2 which run on VMware virtualization on Blade Server.
Because of that our DRC planning will be done by restoring VMware images.
But, there are issues when we try to restore the Production servers images (seperated between PROD-CI and PROD-DB)
On OS level, IP, Hostname also the SAP parameters has been replaced with the new ones (named PROD-CIDR and PROD-DBDR), the issues came up when we try to change to change DB2 hostname parameter using :
db2set -g DB2SYSTEM=[new DB2 server hostname]
we got this error:
DBI1309E System error.
Explanation:
The tool encountered an operating system error.
User response:
A system error was encountered during registry access. Ensure that there
is enough space on the file system where the registry is located, and
that there is a valid LAN connection if the registry is remote.
when we looked at the db2diag.log, we got this info:
FUNCTION: DB2 Common, Generic Registry, GenRegBin::Change, probe:240
MESSAGE : ECF=0x900001EE=-1879047698=ECF_GENREG_RECORDBUF_FREEMEM_FAILURE
Failed to free recordbuf memory
CALLED : DB2 Common, OSSe, ossMemFree
RETCODE : ECF=0x900003EE=-1879047186=ECF_MEM_NULL_POINTER
The address provided is NULL
FUNCTION: DB2 Common, OSSe, ossMemFree, probe:20
MESSAGE : ECF=0x900003EE=-1879047186=ECF_MEM_NULL_POINTER
The address provided is NULL
DATA #1 : String, 75 bytes
NULL pointer for memory allocation address found at: GenRegBin.C, line 1453
FUNCTION: DB2 Common, Generic Registry, GenRegBin::Change, probe:70
MESSAGE : ECF=0x900001BC=-1879047748=ECF_GENREG_FAILED_TO_LOCK_REGISTRY
Failed to lock the registry
CALLED : DB2 Common, Generic Registry, GenRegFile::Lock
RETCODE : ECF=0x900001DA=-1879047718=ECF_GENREG_UNABLE_TO_OPEN_LOCK_FILE
Unable to open the lock file
FUNCTION: DB2 Common, Generic Registry, GenRegFile::Lock, probe:50
MESSAGE : ECF=0x900001DA=-1879047718=ECF_GENREG_UNABLE_TO_OPEN_LOCK_FILE
Unable to open the lock file
CALLED : DB2 Common, OSSe, OSSHFile::open
RETCODE : ECF=0x90000001=-1879048191=ECF_ACCESS_DENIED
Access denied
Does anyone have this issue before?
Kindly help,
Regards,
StanDear All,
Finally I got the chance to give an update...
Just yesterday, I finally succeed to replicate and configure the DR server of our QA system.
Our steps are:
Replicate the QA Server
Build new server as DR server, set networking not to connect at power on
After power on the server, I change some setting, which isChange /etc/hosts value,
Need to change the IP address, set the new IP and leave the hostname as it is
Change Network Setting from YAST,
When we create new server from replication, they will create new connection properties (set as eth1), where the new assigned network hardware set. The old connection properties (set as eth0) contain the old IP, and will not contain hardware information/empty. So we need to delete the old connection properties and set the new IP to the new connection properties (also change the conf name from eth1 to eth0)
Connect DR server to the network
After this, we already can ping the DR server
Start SAP services
Then, the SAP DR can be accessed by SAP Logon by adding new connection while the real QA is still online.
So far, we've tested it up to that point and haven't try to insert some transaction and also haven't check any issue related to SAP parameters.
If there's no trouble, we intended to replicate the Production servers...
Any inputs / suggestions about this? Is there any point that we need to check first at this point?
Regards,
Stan Beta -
User Password change fails in OWA 2013
User Password change fails in OWA with this error: Your password couldn't be changed. Make sure the old password you typed is correct and that the new password meets the minimum security requirements.
We are migrating from Exchange 2007 to Exchange 2013. Have mailboxes in both environments. OWA 2007 password changes succeed (user mailbox is still in Exchange 2007). When the user mailbox is moved to Exchange 2013, password changes fail
with the above error.
We have the Exch 2013 servers are on Windows 2012 and we are running Exch 2013 CU3. We have made changes to the Default Role Assignment Policy to prevent users from changing Contact information and setting user photos, etc. We are not exactly
sure when user password changes stopped working, or even if they ever did work, although we recently installed our Prod Exch 2013 servers alongside our 2007 servers without any RBAC delegation implemented and a quick test of a user password change was successful.
I reversed all the changes to the Default Role Assignment Policy but the password change still fails.Hi,
Please try the following steps in your CAS server:
1. Click Start > Run and type regedit and click OK.
2. Navigate to the "HKLM\SYSTEM\CurrentControlSet\Services\MSExchange OWA" key.
3. Set the ChangeExpiredPasswordEnabled value from 1 to 0.
4. Close regedit and re-open it.
5. Set the ChangeExpiredPasswordEnabled value from 0 to 1.
6. Close regedit.
7. After you configure this DWORD value, please reset IIS. The recommended method to reset IIS is to use IISReset /noforce from a command prompt.
Here is the similar thread about password change issue in Exchange 2013 CU3, please refer to:
http://social.technet.microsoft.com/Forums/en-US/30b74c81-9b98-46f4-9ca0-1c3bb74f4a3f/users-with-expired-passwords-or-change-password-at-next-logon-unable-to-change-password-via-owa-in?forum=exchangesvrclients
Hope it helps.
Thanks,
Winnie Liang
TechNet Community Support -
Revision: 14655
Revision: 14655
Author: [email protected]
Date: 2010-03-09 18:41:52 -0800 (Tue, 09 Mar 2010)
Log Message:
Fix hostname in failing MXUnit proxy service tests. The hostname flexteam.macromedia.com no longer resolves. Changed the tests to just use flexteam as the hostname. We probably shouldn't have tests that rely on flexteam but we can worry about that later.
Modified Paths:
blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/proxyService/202863/bug202863Doc Lit.mxml
blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/proxyService/202863/bug202863Rpc Enc.mxml -
Unreserve funds failed. Contact Purchasing Administrator if necessary
Dear All:
When want to change the detail for one requsition in iProcurement, show the error"*unreserve funds failed. Contact Purchasing Administrator if necessary*". How can I solve the issue?
My environment is : Oracle R12.1.3 | Aix 6.1
Regards
TerryHi,
Could you please check what is the value set for the profile --> POR: Enable Check Funds..? set it as "*No checkfunds"* and try again to change the requisition.
You can check below URL for details :
http://forums.oracle.com/forums/thread.jspa?threadID=2179974&tstart=60
/S.P DASH -
One of the user is getting the below error when the person is trying to login ELM system. what could be issue for the specific user and how do we resolve this issue?
"Not able to login PIA - An error has occurred. You may attempt to sign in again. If your attempt fails, please contact your System Administrator"Its works for other users, its only happened for one specific user only? I didn't check the APPSRV.LOG file? what needs to be checked in APPSRV.LOG, I can ask my infra team to check, because I don't have app server access to check log file.
-
I want to change it to my husbands so all of our information syncs on to my iphone and our ipad, but will this completely delete my iCloud account? and by doing this how will my phone change (such as contacts, photos etc.) ?
Bad idea.
What information do you want to share, exactly? You can share contacts, reminders, and calendars with other iCloud users without the need for both of you to use the same iCloud account. You can authorize both phones to use apps purchased under the same Apple ID without sharing an iCloud account.
Sharing an iCloud account is a bad idea in general. There is too much opportunity for someone to damage or delete data that will affect both. -
Weblogic 10.3.0.0 installer - Failed to contact Server
When clicking 'Next' on the 'Specify Download Options' portion of the wizard I get an error message "Failed to contact Server"
Anyone know why I recieved this message or how I can get around it?OK , I have checked the log files for the server - it says it is using NON-BLOCKING source file:/dev/urandom
Looks like this must have been sorted out in 10.3.5 as it recognizes the Linux System.
I have the same issue on all 6 of the servers I have installed - so this may be a different issue.
These are BL460c g6 HP blades in a c7000 chassis.
So now I am at a dead end.
The initial wait is still considerable, but we may have to live with this (Ubuntu Server 11.04 is still new and probably not supported well at this time)
The admin console works fine once it initially opens and is fast.
I tried the java command as well and got an error finding the main class in weblogic.wlst, (not the end of the world).
all in all though it looks impressive right now, aside from the minor admin stuff, my application runs fine (which is what counts in the end).
I will leave this open so that anyone else can view it and make suggestions. -
DFS Replication failed to contact Domain Controller.....
I have seen this error since the inception of this stand alone AD PDC instance of Windows server 2012 R2 Essentials. I understand that Essentials does not support other Domain Controllers ; Member servers ; or trust between Domains of any kind. I also
understand that DSF Replication is a service that replicates files between other servers and other domain servers that Essentials dose not want to talk to.
So my question is why am I seeing this DFSR error 1202 in my event log, if Essentials does not support communication to other servers and domain servers? Maybe a better question is why does Essentials even try to implement this
service? Do I even need to try to resolve this issue or should I just disable it and move on?
Contents of Error:
Log Name: DFS Replication
Source: DFSR
Date: 2/6/2014 1:57:57 PM
Event ID: 1202
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: Hxxx2.xxxxxxxxxxxxx.local
Description:
The DFS Replication service failed to contact domain controller to access configuration information. Replication is stopped. The service will try again during the next configuration polling cycle, which will occur in 60 minutes. This event can be caused
by TCP/IP connectivity, firewall, Active Directory Domain Services, or DNS issues.
Additional Information:
Error: 160 (One or more arguments are not correct.)
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="DFSR" />
<EventID Qualifiers="49152">1202</EventID>
<Level>2</Level>
<Task>0</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2014-02-06T19:57:57.000000000Z" />
<EventRecordID>194</EventRecordID>
<Channel>DFS Replication</Channel>
<Computer>Hxxx2.Hxxxxxxxxxxxxx.local</Computer>
<Security />
</System>
<EventData>
<Data>
</Data>
<Data>60</Data>
<Data>160</Data>
<Data>One or more arguments are not correct.</Data>
</EventData>
</Event>Hi,
Did you mean that you did not configure a DFS server in the new DC but you get the DFSR error 1202 in your event log? Then the issue is not related to the existing SBS domain.
Please try to turn off the Windows Firewall to check if it causes the issue. You could also refer to the articles below to troubleshoot the issue:
Newly Promoted Win2K8 DC is not advertising as Domain Controller.
http://blogs.technet.com/b/niraj_kumar/archive/2009/04/23/newly-promoted-win2k8-dc-is-not-advertising-as-domain-controller.aspx
Restrictions for Unauthenticated RPC Clients: The group policy that punches your domain in the face
https://blogs.technet.com/b/askds/archive/2011/04/08/restrictions-for-unauthenticated-rpc-clients-the-group-policy-that-punches-your-domain-in-the-face.aspx
Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
i have a problem in buying zynga poker chips, every time i try to buy chips they tell me contacts itunes support and the the purchase always failed, i contacted zynga but they told me that i have to contact itunes because they don't know the problem ?
P.S i always use my credit money from gift cards to buy anything from itunes or in apps - purchasing.
so what do u think should i do ?Have you tried contacting iTunes support : http://www.apple.com/support/itunes/contact/ ?
-
PJC Calendar setDate Wrong date format. Date change failed?
Forms 10.1.2 using forms demos pjc code.
The calendar pjc I added to my form works except I can't initialize it with a date. If I try to initialize a date it always produces 'Wrong date format. Date change failed.' error.
In a post-query trigger, I initialize the calendar's date using:
SET_CUSTOM_PROPERTY('PJC.CALENDAR',1,'setDate',to_char(:lead.date_received,'DD.MM.YYYY'));
In the java console, this yields:
Warning: Wrong date format. Date change failed.
Warning: Wrong date format. Date change failed.
I get the same result when using a hardcoded date like:
SET_CUSTOM_PROPERTY('PJC.CALENDAR',1,'setDate','01.12.2006');
What is the flaw in my incantation?Hello,
This is the syntax used in the calendarpjc Forms demo:
call the setDate method on the calendar PJC via the PL/SQL built in
set_custom_item_property
convert Oracle date to String recognised by Java
procedure setDate(d in date) is
begin
set_custom_property(lGlobals.hCalendar,1,'setDate',to_char(d,'Mon DD, YYYY'));
end; Francois -
[SOLVED] Firefox: failed to contact configuration server.
When I start firefox, the full error message is:
An error occurred while loading or saving configuration information for firefox. Some of your configuration settings may not work properly.
Failed to contact configuration server; some possible causes are that you need to enable TCP/IP networking for ORBit, or you have stale NFS locks due to a system crash. See http://projects.gnome.org/gconf/ for information. (Details - 1: Failed to get connection to session: /usr/bin/dbus-launch terminated abnormally with the following error: Failed to waitpid() for babysitter intermediate process: No child processes)
Failed to contact configuration server; some possible causes are that you need to enable TCP/IP networking for ORBit, or you have stale NFS locks due to a system crash. See http://projects.gnome.org/gconf/ for information. (Details - 1: Failed to get connection to session: /usr/bin/dbus-launch terminated abnormally with the following error: Failed to waitpid() for babysitter intermediate process: No child processes)
Failed to contact configuration server; some possible causes are that you need to enable TCP/IP networking for ORBit, or you have stale NFS locks due to a system crash. See http://projects.gnome.org/gconf/ for information. (Details - 1: Failed to get connection to session: /usr/bin/dbus-launch terminated abnormally with the following error: Failed to waitpid() for babysitter intermediate process: No child processes)
Failed to contact configuration server; some possible causes are that you need to enable TCP/IP networking for ORBit, or you have stale NFS locks due to a system crash. See http://projects.gnome.org/gconf/ for information. (Details - 1: Failed to get connection to session: /usr/bin/dbus-launch terminated abnormally with the following error: Failed to waitpid() for babysitter intermediate process: No child processes)
Failed to contact configuration server; some possible causes are that you need to enable TCP/IP networking for ORBit, or you have stale NFS locks due to a system crash. See http://projects.gnome.org/gconf/ for information. (Details - 1: Failed to get connection to session: /usr/bin/dbus-launch terminated abnormally with the following error: Failed to waitpid() for babysitter intermediate process: No child processes)
I don't have dbus or hal running, as I have disabled input-hotplugging. Is there any way to fix this?
Also, before I start firefox, I have 0 dbus processes running, and after it gives me that error message, I get:
pgrep dbus | wc -l
381
I have switched to chrome which doesn't seem to have any troubles. I would really like to have firefox though.
NVM: I went through the config options for firefox, and --disable-dbus exists
Last edited by tomd123 (2010-01-09 20:24:55)I'm not entirely sure, but here is what I would do:
1. Create a new user account and try to start firefox as that user.
2. are hal / dbus running (check with ps -ef |grep hal)
3. If 1. works and hal/dbus are running, log out and remove everything under /tmp owned by you , plus .dbus/session_bus/*. -
how can i change apple id contact email address?
thank youI have listed my husband's email address on find a phone as an additional contact email address on my apple ID however have mucked up his apple ID in doing so.
Have been onto Account information page as above like you suggested but not able to find where to alter the contact addresses.
Can you help?
Thanks -
N8: Phone Start-up failed. Contact your retailer!!...
Hello Nokia,
I just woke up to find this error on my N8 and now i can't turn on the phone bacuase after the Nokia Logo then this message comes "Phone Start-up failed. Contact your retailer". What should i do to get it back cos i can't do anything now since all my information is on my phone.
I wanted to even connect it to the computer and use it as a USB drive to get some of my info but the msg still appears.
Pls help
Kind regardsIf your not getting to the homescreens then it's likely you have a very diferent issue to the one described in the post linked,
If you get to the homescreens then it's likely either the nokia sign in thing or just too much starting at once that's hitting you,try putting the phone into offline mode before it comes up and letting it complete its boot,
otherwise if it is happening at the nokia logo screen, then it sounds like something has gone badly wrong,
if you are running anna then you may need to perform a multi fingered reset which will erase the data stored on the phone and restore it to an out of box state, before recovering from a back up that you have made previously,
If that deosn't work then a trip to a nokia care point is your only course of action
Maybe you are looking for
-
How to save message into internal table?
Hi,everyone! I have a problem when I'm coding.I want to store messages into a internal table.Can you help me? Thanks!
-
I have one program that generates a Smartforms and then it submit another program that prints another forms. Both programs use OPEN FORM to create it and those programs are called via SUBMIT command. The problem is that I tried to use the parameter "
-
Lenovo x201 Audio Popping/Buzzing/Stuttering
Okay. I'm at my wits end. This has been going on for about a year now. I've learned to ignore it, but now that I really want to use my laptop for music, it is getting annoying. There are times when playing audio that the quality starts to degrade. Th
-
I have recently experienced a hijacking on my account. All is fine now, but I have this Visa attached to my account by the hijacker that won't go away. They made a purchase to get "Peggle," most likely using a messed up card as it is wanting me to in
-
Hello! I'm having a problem implementing the DAO pattern. Suppose that I have two database tables: emp(id, name, sex, deptid) dept(id, name) If I follow the DAO pattern, I use two DAO interfaces, one for each table, and "entity". EmployeeDAO, and Dep