How do I make my waveform send one point per iteration in a loop?

Hello,
I am trying to create a demonstration/lab for a future course at my university. I am trying to send data from a wind turbine to a third party DAC in order to run a motor. I have found out that when I send a wave form to the DAC I must send one point per iteration if I use the arbitrary signal generator. I would like to be able to send a file to the DAC without manually loading it as the arbitrary signal generator does. I was wondering how to send the data using one point per iteration using the build waveform or other waveform function that can have the waveform built from a file that is added on the front panel. I am using labview 8.0.
Thanks,
Laura
Message Edited by lhoising on 03-30-2007 01:21 PM
Message Edited by lhoising on 03-30-2007 01:25 PM

Maybe I am asking the wrong question. Maybe I should be asking why it is that when I send a waveform to the the DAC (using active x controls) the signal that is sent to the DAC is just the final value. I probed the wire connected to the data input of the DAOUTPUT node and it shows the entire waveform graph and not just the last value.
Thanks,
Laura

Similar Messages

I have 2 new iPhone 4s. Messages from other iPhone users appear on both of my new phones. I want these seperate. How do I make these independent of one another?

I bought my daughters new iPhones (4s) for Christmas. They love them except that when another iPhone user text one daughter, the other daughter gets the messages and same for the other daughter's text. How do I make these independent of one another without putting my family on separate ITunes accounts?

When you were setting the phones up you should have been asked if you wanted to use the phone number or an email address for FaceTime/messaging. My guess is you used the same email for both phones. Just go in and change it. That or you have the same iCloud id on both phones, I'm not using the cloud so I can't help you there.

TS2755 Is there a fix to deleting already deleted address book contact, from messages search? i.e. when you type in say letter c in messages search, all contact with a c, past already deleted and current all appear? How do you make the old deleted ones a

Is there a fix to deleting already deleted address book contact, from messages search? i.e. when you type in say letter c in messages search, all contact with a c, past already deleted and current all appear? How do you make the old deleted ones appear?

only way is to restore the phone as new. OR wait until IOS 7 comes out in the fall.

How can I make two Canvas in one Window ?

I want in the main window ( that is only window in the module ) press button to appear another canvas.
but that I can't make it , I just made two window until the another window appear.
that's all
I tried with :-
show_view('canvas_name');
but didn't work with me Sad
the another canvas made it stacked Canvas .... but also didn't work Sad
so please , How can I make two Canvas in one Window only ?
and thanks in advance

this code work with me :-
show_view('canvas name');
go_block(block_name');
execute_query;
for HIDE button u have to write...
hide_view('canvas_name');
but
that not exactly what I want ...... I want the stacked canvas appear like second window , and could control on it like window .... it could be possible ????

HT202060 How can I make Activity Monitor show one graph instead of four for MacBook Air?

How can I make Activity Monitor show one graph instead of four for MacBook Air?

Learn about OS X: Activity Monitor shows one CPU Usage graph on systems with more than four cores
Copied and pasted from top of the page.

All songs in my iTunes library are listed twice. I have two copies of my library in two different locations. How do I make iTunes work with one copy of my library?

All songs in my iTunes library are listed twice. I have two copies of my library in two different locations. How do I make iTunes work with one copy of my library?

That is the way the iphone works.
You need to copy everything from your backup copy of your computer.

Keep on getting double notification from my default mail app, and gmail app, how do i make google my primary one?

keep on getting double notification from my default mail app, and gmail app, how do i make google my primary one? so that i dont have to get doulbe notifications on both apps

This is probably not the answer to all your questions, but I am sure it answers some.
Unlike Word and InDesign, FrameMaker's anchored frames, which hold graphics, "hang" from their insertion points, typically at the end of the paragraph. An anchored frame that follows a paragraph is set to be below the line, the line being the last line in the paragraph. If you turn on View > Text Symbols, you will see a marker that indicates the point from which the anchored frame is hanging.
If the anchored frame is taller than the available space, it is moved to the next page ALONG with that last line. If the paragraph style/tag has a widow/orphan lines number that is more than 1, then that number of lines are also moved to the next page, because the paragraph tag says to keep that many together, EVEN if there is space at the bottom of the previous page.
So, you can set the widow/orphan lines number smaller OR as you have done put a blank line before the anchored frame, which now holds the marker for the anchored frame, and set its font size to 2 pt (the lowest FrameMaker allows) and its line height to zero. This is the standard workaround UNLESS you use the line above the anchored frame as the title/caption of a figure, which is also a typical way of dealing with FrameMaker's ways.
To my knowledge, one cannot change the default of the checked cropped box. Maybe others know of some way to change this.
There is no page break in FrameMaker, hence there is no symbol for it. In the paragraph designer for the paragraph, you set to Start of the paragraph to Top of page. Top of page is FrameMaker's equivalent to a page break. To "remove" a page break, set the Start of the paragraph to Anywhere.
Since you are new to FrameMaker, I suggest reading throught the User Manual that comes with FrameMaker. You will likely find the answers to most of your questions there.
Hope this helps,
Van

How do you make a photo in DW that changes automatically in a loop and needs no visable buttons

How do you make a photo in DW that changes automatically in a loop and needs no visable buttons?

I'm sorry to be so vague. I have recently found out that what I want
to do is put my images in a javascript image rotator. I have looked
this up on google and have now tried about 6 different codes. I try to
follow the insert directions but I must be doing something wrong. I
get the first photo linked up but can never make the picture change to
show the other two photos in the image folder.
Can you direct me as to how this works in dw?
Thank you so much for helping.
Pam

How do I make a video on one track expand in size over a video on a second track? Elements 11

How do I make one a video on one track expand in size over a video on a second track?
Thanks.

Sminty
Thanks for the follow up with additional very helpful information.
What you need to do is to keyframe the Motion Scale property so that it changes over the duration of the whole photo
rather than Scale being applied to the whole photo uniformly.
Two ways you could do the keyframing of Scale..
a. from the Timeline
or
b. from Applied Effects/Applied Effects Palette/Motion Panel expanded and its Scale Property there, using Toggle Animation to initiate the process.
For now, I will describe "b"
Your scaled down image on Video Track 2
Your regular image on Video Track 1
Your Timeline Indicator at the beginning of the Timeline.
Select/Highlight the image on Video Track 2, go to Applied Effects Tab/Applied Effects Palette/Motion Panel Expanded and its Scale Property
That area should look like
You get an abbreviated version of the above screenshot if you do not hit the Show/Hide Keyframe Controls icon. With it opened, you will see the actual keyframes being placed.
With your Timeline Indicator at the beginning of the Timeline and Video Track 2 Image selected, click on the Toggle Animation Icon. That will set the Scale property keyframes
which at that time will be at a value less than 100% because you are starting with a scaled down Video Track 2 Image.
Then move the Timeline Indicator to the last frame of the clip. Then move the Scale slider to 100% or whatever % gives you Video Track 2 Image just to full frame so
that you do not see the Video Track 1 image. Render the Timeline by pressing of the Enter key of the computer main keyboard or pressing the Render button above
the Timeline.
All sorts of things can be done by keyframing a property. The property could be other than Scale (some examples might be Position, Opacity, certain effects applied
to Timeline content, etc.)
Please review and consider and then let us know if that worked for you. Do not hesitate to ask for clarification if needed.
Thank you.
ATR

BPC 10.0 NW - How do I make Business Rules run one Period at a time

I was wondering if anyone has a way to make business rules run one period at a time before moving on to the next to the next time period (i.e. January 2014 calc prior to moving on to February 2014). In past SQL this could be achieved with a piece of script *CALC_EACH_PERIOD. Is there anything like this that can be applied in the NW platform for Business Rules? I have some logic that I want to run through a package on multiple periods at once. Part of this logic contains a Business Rule that uses a value from the preceding period. the Business rule appears to be calculating all time periods selected in the package at once so it is missing the piece that is supposed to come from the prior month unless the package is run one period at a time. I need the logic to run sequentially by time period (oldest first) when more than one time period is selected.
thanks,
Keith

Hi Vadim,
Script for the business rule is below, it runs along with the FX_Trans rule in the same package ( I have also attached a screen shot of the actual Business rule its self)
*RUN_PROGRAM CALC_ACCOUNT CATEGORY = %CATEGORY_SET% ENTITY = %ENTITY_SET% CURRENCY = USD //GROUPS = %GROUPS_SET% TID_RA = %TIME_SET% //OTHER = [AUDITTRAIL=%AUDITTRAIL_SET%] CALC = CALC_HIST_USD *ENDRUN_PROGRAM
Thanks, Keith Carlson

How can I make a change on one computer effect other compujters automatically

If I change a bookmark on one computer, I want that bookmark reflected on all the other computers. It seems as if I have to do the sync on system A to get the change to the server; then I must go on System B, change the sync type to copy from the server and do a sync. This is way too cumbersome. If synch means to have the same data everywhere, why isn't the default to make this happen as one logs into each system? right now if I make a change on one system and do a synch, it will get overwritten when I go to another sysem and synch.

We use test sites on our remote server. We purchase a cheap $2.99 .info domain and give it a unique domain name. We then make it an addon domain on our remote server.
When we're building sites we then make a unique subdomain to the addon domain. We upload our files to each unique site's subdomain so we can see and test them live,.then we can contact the client
and tell them to take a look at their site live, which at the time is a subdomain, etc.and uploaded.
Once we have the site completed and uploaded to the designated subdomain we then contact the client and ask them to test their site and see if it's ready or do we need to make more changes.
We use a hosting package for this that cost us less than $30.00 a year with unlimited domains and subdomains. We've got about 30 subdomains on it now and they're not even making the usage wiggle because of taking very few hits.
Once the site is completed and approved we then delete that particular site's subdomain and upload to the clients remote server.
We don't test our sites locally, we test all our sites live as we build them using a subdomain to the .info tld domain on our remote server. You can also buy hosting packages for around $12.00 a year to test your sites on.

How do you make the background all one color without disturbing the subjects?

I shot a wedding this past weekend. Where the bridal party walked in there was an acrhway with christmas lights as the only lights. It made the background all splotchy. I have tried the paintbrush tool, but only preset choices, such a textures and such. Won't help. I need to work around people and make the background all one color. I've tried using a vignette, but it made it too dark, and when you lighten the exposure you see all the splotches. Does anyone have any advice. I am in a jam, I want the colors to be uniform for all the bridal party....and not look like someone threw paint on the wall. HELP PLEASE!
I'm using Adobe Photoshop Elements 10.

You'll need to post an example so we can figure out the best way.
Ken

How do I make images tilt to one side in Fireworks?

I have Fireworks MX --- I know how to import an image, but
how can I make it tilt slightly? I don't want a full rotate, but
make it slanted.
Thanks

HI, two ways that I know of. The quickest is, with your image
selected,
choose the 'Scale' tool from the Tools panel on the left,
then you can
rotate the image just by dragging the rotate icon. Or for a
more precise
method go to Modify > Transform > Numeric Transform
> select Rotate from the
drop down menu and enter the angle amount you require.
Peter
"Miss_Angela"
|I have Fireworks MX --- I know how to import an image, but
how can I make
it tilt slightly? I don't want a full rotate, but make it
slanted.
|
| Thanks
|

Magic Packet - How to get my router to send one

I have the Quantum Gateway 1100 router. I have a NAS Server on my home network. The NAS server has the capability to Wake on LAN if the router can send that packet. Can anyone tell me how to get the router to send the Wake-on-Lan packet to the server. FIOS Tech Support is completely and totally useless.

Hi,
You can do a fresh installation using the installer bits available at the following link/location Download CS5.5 products
For suites, you need to download and copy both .7z and .exe in the same folder. Clicking .exe will extract all relevant installer files. You can then install the suite. Use your existing Serial number when prompted.
regards
Aj

How can I make multiple quizzes within one Captivate project?

Hi guys! Really liking Captivate 5.5, especially the way random question slides can lift questions out of a question pool...very elegant!
Sadly though, I've come up against a bit of a wall. In my project, I want to have 3 separate quizzes that all use the same question pool; a 10, 30 and 50 question-long quiz. Each one needs to have its own results page.
It's easy enough to see what I mean by looking at the screenshot below:
The idea was to have about 105 slides in total, with slides 10 - 20 being the 10 quiz slide, 21 - 51 being the 30 question quiz and 52 - 102 being the 50 question quiz.
There are three invisible buttons placed over those 10, 30, 50 text boxes. In the picture, the '10 question' button would jump to slide 10, the '30 question' button would jump to slide 21, and the '50 question' button would jump to slide 52, jumping the user to the start of their designated tests.
Though I can create the 10 random question "block" easy enough, when it comes to adding the 30 question "block" it just adds the new random questions to the existing random questions. I want three separate quizzes, each with their own results screens please. (I don't want to daisy-chain to external projects, because the results of each test need to be used within the homepage.)
It just adds them on to the existing block!! Argh!!
Little bit ticked off with Adobe...the reason their products are so incredible is because they put no constraints on the user, and you can use their tools to create things even the developers never dreamed of. Like in Photoshop for example, I bet when the dropshadow fx was created, the developers never realised that it would be used to give a metallic 'stamped' look to text by turning it to white and applying it just inside the text.
Captivate, though amazing most of the time, has a nasty habit of stomping on my toes. You can't set grade boundaries and have quizzes give out grades A+ to F- for example. You can only have 'pass' and 'fail', thus making it rather pointless for use in schools, contrary to how the program is advertised. Another example would be when I wanted to create a replay button. I thought that a button that jumped to the slide it was on would be a simple, no-BS replay button, but for some reason you can't make a button jump to its current slide. I downloaded a widget that worked in the end, but I wish Adobe would get off my back and let me do what I want!
Anyway, if you could help me out here it would be grand

I must say I have a little sympathy for the Captivate developers on this occasion. As you say, they've created an application that does so much, that when you eventually run into a hard boundary of some kind, the effect is somewhat jarring. However, every application, no matter how good, has limits. I'm probably one of the worst offenders when it comes to asking the Adobe Captivate Development Team for enhancements (I think I've logged over 70 enhancement requests for Captivate 6 alone).
In your case, you want to have three different quizzes in one project file, each with it's own separate Quiz Results page. Lilybiri's blog explains how to set up your own faux Quiz Results pages using system variables and custom user variables, but you're going to find this to be quite a lot of trouble. Even if YOU want to consider these as three separate quizzes, as far as Captivate is concerned they're just one big quiz with 50 questions. So Captivate will calculate it's internal results based on a 50 question quiz, even if your users select the 10 question version. So achieving a final Pass/Fail result is going to be problematic at best.
As Lilybiri suggested, your better strategy would be to break this up into separate modules so that you can get your three separate quiz results (all done in standard Captivate) as well as correct results based on the actual number of questions done by the user.
As far as grades A-F is concerned, there's nothing to stop you from using Advanced Actions and User Variables to calculate the user's score as a grade. You need a user variable that stores the user's grade (e.g. var_Grade). And you need a fairly complex Conditional Advanced Action (e.g. caa_CalculateGrade) with several clauses each of which goes something like:
If
cpQuizInfoPointsscored is lesser or equal to [highest score for a particular grade]
AND
greater or equal to [lowest score for a particular grade]
Actions
Assign var_Grade with [the appropriate grade for that range of scores]
Your conditional action will need one of these clauses for each separate grade. Once your variable has been assigned a grade based on the user's score, you can display it in a text caption somewhere on the quiz results page or on a slide thereafter with suitable commendations/ commiserations.

How do I make my waveform send one point per iteration in a loop?

Similar Messages

Maybe you are looking for