How do I monitor a Cisco 1700 Series T1 Serial Port.

I have a Cisco 1721 Router and I am looking to monitor it for hourly statistics to find max and min speeds. How would I go about doing this? I know if I do a show interfaces it shows me all the data since the last time the counters were reset. Thanks for any help.
Chad
Diversified Telecom.

http://www.paessler.com/
There are many others.

Similar Messages

How to bridge a linksys cisco E1200 series router?

I have recently purchased a linksys cisco E1200 series router and would like to know how to bridge the connection to my xbox

purchase 881w, get rid of linksys. That should do it.
Sent from Cisco Technical Support iPad App

How to move a standalone Cisco C series to UCS managed service profile without losing data?

Hi,
We currently have a standalone cisco C series server with Windows 2012 installed on the local disks. We need to move this server to Cisco UCS managed with a service profile but cannot lose the existing data and OS boot method.
Does anyone know how to do this?
Thanks

Hi Adrian,
To be able to accomplish this set the local disk policy to "Any Configuration" this way UCSM won't overwrite the current raid configuration on the server.
See link below
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/2-1/b_UCSM_GUI_Configuration_Guide_2_1/b_UCSM_GUI_Configuration_Guide_2_1_chapter_011110.html#task_897FABF194524BDF8C0EF72E755972F0
Let it me know if this helps

Tunneling on cisco 1700 series

Dear all,
I have a cisco1700 series route which contains two ethernet ports.I don't want to use serial ports.I have a broad band connection(i.e. through smart bridge). One etherent is connected to smart bridge. & other one to lan.
How can i configure the router by using tuneling so that i can shift all the load on broad band connection?
Pls. provide each step.
Thanks
Tarlochan

Here is a sample configuration for a GRE tunnel:
Router# configure terminal
Router(config)# interface Tunnel0
Router(config-if)# tunnel source
Router(config-if)# tunnel destination
You can have GRE destinations on the physical interfaces or you can use loopback
interfaces as well.

Cisco 1700 series startup problem

I have a cisco 1700 .After a blackout this router is not configured. After recounfigured router save running-config in startup-config and works fine until new blackout. Any idea ?
Thanks (sorry for my english)

Does it also do the same when you power cycle the router.
Sounds like your conf register is not set correctly.
Do a "show system" and look for "Configuration register is 0x2102" at the bottom of the output.
If its not set to this then you can change it by issuing:
my_router(config)#config-register 0x2102
HTH
PJD

How to transfer file from PC to PC via serial port using labview

I need to transfer files(.txt, .doc, .xls) from PC to PC via serial port using LabVIEW. Is it possible to transfer files, if so how to transfer?
Solved!
Go to Solution.

Yes, it is possible to transfer files with the serial port using LabVIEW. Files are just collections of bytes and the serial port is pretty good at shipping bytes from one PC to another. You need to connect the serial ports together with a null modem cable.
First, take a look at the example for serial communication. In LabVIEW, go to the Help menu and select "Find Examples...". From there you can search for "serial" or navigate to Hardware Input and Output >> Serial. Select the "Basic Serial Write and Read.vi". Experiment with that example to gain confidence on the serial communication methods.
Next, it's time to learn about how to read and write files. For that, the examples could be somewhat confusing since they all deal with files that are presumed to have data of a specific type in them. I would recommend just getting familiar with the functions on the File I/O palette. Specifically, get to know the following functions.
Open/Create/Replace File - On your destination side, you'll need to create the copy of the file that you are trying to transfer
Close File - When you are finished reading from or writing to a file, you should close it. It cleans up the memory being used and finalizes any write operations that are still floating in the write buffer.
Read From Binary File - The best way to read from a file when you do not really care what type of file it is. In your case, you just want to get those bytes read and sent out so they can be written down at the destination.
Write to Binary File - At the destination side, this is what will store those bytes to the file you created with number 1.
Get File Size (under the Advanced File Functions sub-palette) - You need to know how big the file is so you know when you are finished.
OK, so once you are able to create files, write bytes to them, and read bytes from existing files you can move on to transferring.
The basic method I would suggest is to have the user specify a source file on the source PC and a destination folder on the destination PC. Then, find out the size of the source file using number 5. Divide that size number by the number of bytes you feel like transferring at once. The serial buffers are usually around 32k (if I remember correctly) so do not exceed that. Now begin sending data by reading some number of bytes and wiring that string output to the VISA Write function. On the destination side, you'll want to be monitoring the serial port for bytes and reading them when they arrive. Wire that string to the Write to Binary File function to add them to your destination file.
That is the basic outline of how to do it. You have to be careful not to overload the write and read buffers on the serial ports. Initially you can use delays on the sending side to make sure the reading side has enough time to digest. To get things moving faster, you can bring in some flow control.
If all that sounds a bit intimidating, there are Alliance Member companies out there (such as PrimeTest Automation) who can write such code for you and even provide a turnkey solution for you.
Happy wiring,
Dan Press
Certified LabVIEW Architect
PrimeTest Automation

Cisco 1700 Series T1 Point to Point Change Clock Source

So I am trying to change the clock source on my already setup cisco t1 point to point, but it wont allow me to. I have had many people tell me 10 different things that I have to do but no one seems to know how. I put in the command clock source internal, but it says its an invalid command. Any help would be much appreciated.

My current version is....
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV3Y-M), Version 12.2(8)YN, EARLY DEPLOYMENT RELE
ASE SOFTWARE (fc1)
Synched to technology version 12.2(11.2u)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Wed 30-Oct-02 10:22 by ealyon
Image text-base: 0x80008120, data-base: 0x80F47D4C
ROM: System Bootstrap, Version 12.2(1r)XE1, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-SV3Y-M), Version 12.2(8)YN, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)
pe-wen-01 uptime is 1 day, 18 hours, 19 minutes
System returned to ROM by reload
System restarted at 10:02:41 PDT Tue Jun 12 2012
System image file is "flash:c1700-sv3y-mz.122-8.YN.bin"
cisco 1751 (MPC860P) processor (revision 0x600) with 36864K/12288K bytes of memo
ry.
Processor board ID JAD06370AF0 (4055773928), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
2 Channelized T1/PRI port(s)
WIC T1-DSU
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102

How to decode a set of datas received from serial port and display image on a canvas based on CVI ?

Hi !
I have received a set of datas via rs232 and it contains picture messages. I have to decode the datas first and then display them on a canvas.
I have known several functions that may be used . Such as
int SetBitmapData (int bitmapID, int bytesPerRow, int pixelDepth, int colorTable[], unsigned char bits[], unsigned char mask[]);
int CanvasDrawBitmap (int panelHandle, int controlID, int bitmapID, Rect sourceRectangle, Rect destinationRectangle);
However,I don't know how to set the following parameters according to the actual pixel values and color values.
int bytesPerRow, int pixelDepth, int colorTable[], unsigned char bits[], unsigned char mask[]
What's more,I have no idea how to decode the datas.
The attachment is a incomplete project. I will be very appreciated if anyone could help me .
Best regards.
xiepei
I wouldn't care success or failure,for I will only struggle ahead as long as I have been destined to the distance.
Attachments:
Decode and display image.zip ‏212 KB

Well, things are getting a bit clearer now.
1. Your image is actually 240x240 pixel (not 320x240 as you told before). The size of image data is 57600 bytes which corresponds to that frmat (I was puzzled by such a data size compared with larger image dimensions!)
2. The image is a 8-bits-per-pixel one; this means that you must provide a color palette to create the bitmap
3. You cannot simply copy image data into bitmap fields in CVI: CreateBitmap always produce an image with pixeldepth matched with display colour depth (normally 24 or 32 bpp)
All that means that you must:
1. Create the appropriate color palette with 256 colors: it may be a grayscale or color palette depending on camera characteristics. Grayscale palette can be found in my sample project, while sample colour palettes can be found here (here the description of a "standard" 8-bpp color palette)
2. Create the bits array correctly dimensioned for the color depth of your monitor
3. Get each pixel value from the camera, lookup in the color palette for the appropriate colour and create the RGB informations into the bits array in memory
4. Display the bitmap on the canvas
As a first step, I would configure my system for 256-color display setting, create a bitmap and simply copy image data into it: you should be able to get the correct image back to your screen.
Proud to use LW/CVI from 3.1 on.
My contributions to the Developer Zone Community
If I have helped you, why not giving me a kudos?

Test Network Setup with 1700 Series Routers

Hi,
I'm relatively new to Cisco equipment use. Fortunately I have in my possession two spare Cisco 1700 series routers with which I can set up a lab to learn and play.
I'm not sure what cards to get for them--they have none. Can someone offer guidance? My guess is I can get second hand WIC's on e-bay but I'm not certain the models or options I need.
My goals would be to do the following, at a minimum, (I think! I'm open to suggestions on other options or limitations I might face)
1. Configure a routed network between two subnets connected by a router.
2. Configure the routers to connect to each other, as one would do for say a T1 connection between two remote offices, each having a subnet connected.
Right now the routers have no cards.
Best regards,
Will

Will
I can see benefit from having 1 serial link/subnet and 2 LAN subnets, especially in the variety of scenarios that you could implement with that combination of equipment. (all subnets on a router in the same network, 2 subnets in a network and the other subnet in another network, all subnets in different networks, dynamic routing protocols with auto sumarization enabled, dynamic routing protocols with auto summarization disabled, OSPF on the routers when connected by serial interface or OSPF on the routers when connected by Ethernet interface (is there a DR elected in both situations?)
HTH
Rick

How to control an Xserve G4 with the serial port

I have an Xserve G4 first generation, and was wondering exactly how you would go about connecting to it via serial port incase I need to change something when there is a network issue. I have looked around the internet without much success. It has Leopard Server on it, so Apple says the baud rate is 56700, and 8bit, no parity. So that's all set in the client machine, which is a MacBook Pro with a USB to Serial adapter on it, which shows up in Zterm. Once I'm in Zterm, it just sits there, and pressing enter doesn't prompt a log in. Does anyone see what else I'm most likely missing?
Thanks

Thanks for the reply Cemelot. Yes, I did create a profile in ZTerm. This is what I have it set to.
I also read that you're supposed to run the command "/usr/libexec/getty serial.57600 /dev/tty.serial" on the Xserve itself. It made no difference if I did that or not. I also checked to make sure tty.serial was inside /dev/. Anything else I'm missing? Thanks again.

How to read serial port and substring

I am new for labview .I send data from microcontroller with C languange every 1 minute this codeprintf("T%3.2f,H%3.2f",fTemp_true,fRh_true);
And I read data with Hyperterminal it show this T29.11,H67.88 I want to show 29.11 and 67.88 only and stroe in database. I study connect serial port in example and I have a question. If I use this code.Can I auto read every 1 minute or this code can read 1 time only and I have to click every 1 minute.How to auto read when I send data to serial port with microcontroller every 1 minute. And I cannot substring 29.11 and 67.88 because %3.2f can show T29.11,H67.88 or T129.11,H100 . and How can I simple send data to database. Thank you .

No, you don't have to click run every minute. You just need to place a while loop around the VISA Read. You could use Wait (ms) but it would be better to use something like the Elapsed Time function and wire the time has elapsed output to a case statement with the VISA Read inside the true case.
This is one way to parse the string:
If you have the database connectivity toolkit, you can easily write to a database. There is also something called LabSQL.
Message Edited by Dennis Knutson on 01-22-2010 01:42 PM
Attachments:
Parse String.png ‏16 KB

MIB Required for Bandwidth Monitoring on Cisco 3800 and 3900 series Routers

Hi Team,
Need your help here.
I am planning to do Bandwidth Monitoring on Cisco 3800 and 3900 series Routers. I want to know the exact MIB which I need to use for getting this done.
Thanks,
Karthik Anbumani

Matt, based on feature navigator GLBP is supportted on 3800 series.
Go to this link and search by feature (GLBP)
http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp
HTH
Jorge

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
My questions are How do you direct this utility to point to the desktop or the TFTP folder
does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
My router is suppose to have 10.0.0.3 255.0.0.0
Gateway of 10.0.0.1 255.0.0.0
My TFTP Server 10.0.0.2 255.0.0.0
How do I get the MAC address of the Router or the TFTP Server and which one is required?
my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
=====================================================================================
rommon 10 >
rommon 10 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
?=0
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=
rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
rommon 12 > TFTP_CHECKSUM=0
rommon 13 > SET
monitor: command "SET" not found
rommon 14 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
?=0
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
rommon 15 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 16 >       " not found
rommon 17 >FE_SPEED_MODE=2
variable name contains illegal (non-printable) characters
rommon
rommon 18 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
?=0
rommon 19 > tftpdnld [ur]
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
            IP_ADDRESS: The IP address for this unit
        IP_SUBNET_MASK: The subnet mask for this unit
       DEFAULT_GATEWAY: The default gateway for this unit
           TFTP_SERVER: The IP address of the server to fetch from
             TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
          TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
      TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
          TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
         TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
          TFTP_MACADDR: The MAC address for this unit
               FE_PORT: 0= (default), 1
         FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                        5=Auto (default)
      TFTP_DESTINATION: The flash destination device for the file
                        flash:(default), usbflash0:, usbflash1:
Command line options:
   -h: this help screen
   -r: do not write flash, load to DRAM only and launch image
rommon 20 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 21 >

What I notice in the original post is this error
ARP: address resolution for 10.0.0.2 timed out.
which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
HTH
Rick

IP SLA Monitor on Cisco 2911

Dear all,
I have a cisco 2911 router that is located in my head office LAN and I use this router to connect to my branch networks. I want to configure IP SLA Monitor on this router to track my WAN Links but it does not support the command IP SLA Monitor. My IOS VERSION is c2900-universalk9-mz.SPA.151-2.T1.bin. Please help tell me how I can configure IP SLA on my router.
Any assistance will be highly appreciated.

The Data Technology Package License part number SL-29-DATA-K9 was changed to the AppX Technology Package License that includes DATA and WAAS features with part number SL-29-APP-K9.
SL-29-APP-K9 (AppX License for Cisco 2900 Series) - USD 1,000.00
Please check the Change in Product Part Number Announcement for the Cisco 2900 Series Integrated Services Routers Data Technology Package Licenses link below for your reference(s):
http://www.cisco.com/c/en/us/products/collateral/routers/2900-series-integrated-services-routers-isr/eos-eol-notice-c51-730946.html

Monitoring the Cisco ACE module with SNMP

We use 2 redundant Cisco ACE loadbalancer in our datacenter
The models are ACE20-MOD-K9 with software A2(2.0)
Does anybod know how to monitor the environment (cpu, memory) of such a module with snmp?
We were not able to find an applicable MIB for that module.
The CISCO-PROCESS-MIB.oid (ftp://ftp.cisco.com/pub/mibs/oid/CISCO-PROCESS-MIB.oid) seems not to reflect the correct oid's.
What are the correct oid's for cpu and memory?
Where can I find a detailed documentation for snmp-monitoring the cisco ace module?
thanks

Hi Patrik,
to monitor the ACE I use these two MIB's:
ftp://ftp.cisco.com/pub/mibs/v2/CISCO-SLB-MIB.my
ftp://ftp.cisco.com/pub/mibs/v2/CISCO-ENHANCED-SLB-MIB.my
Example for CPU:
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Normale Tabelle";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
cpmCPUTotalEntry 1.3.6.1.4.1.9.9.109.1.1.1.1
The resource usage and other interesting things you will find with a MIB browser.
Achim

How do I monitor a Cisco 1700 Series T1 Serial Port.

Similar Messages

Maybe you are looking for