How does a voice gateway handle a call received from CUCM?

For example, I have a voice gateway configured via a SIP trunk as a device in CUCM. When our users dial the international pattern (8011!) and CUCM forwards that to the device(gateway) over the SIP trunk, how does the gateway handle that request in terms of matching dial-peers? Is it handled the same way a call incoming from the PSTN would be? By matching the destination pattern?
Ultimately what I'm trying to do is figure out whether our international calling is configured properly but that's difficult to do If I don't know what the gateway is doing with the call once it receives it from the CUCM.
Thanks in advance!

Thanks, we have a conference call Monday and I'll try some debugging to see what's going on. I am a little more confused now if that's possible because my understanding is that they can make INTL calls but based off of the configs I've seen and what you've told me they should be able to. Below are my configs. There is a translation profile applied but it points to a blank rule. I also didn't see any transformations in the route pattern.
mgcp profile default
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
port 0/0/0:23
dial-peer voice 100 voip
incoming called-number .
dtmf-relay rtp-nte
codec g711ulaw
ip qos dscp cs3 signaling
no vad
dial-peer voice 101 voip
destination-pattern 5...
session protocol sipv2
session target ipv4:x.x.x.x
dtmf-relay rtp-nte
codec g711ulaw
ip qos dscp cs3 signaling
no vad
dial-peer voice 2 pots
destination-pattern 911
port 0/0/0:23
forward-digits all
dial-peer voice 3 pots
destination-pattern 9[94]11
port 0/0/0:23
forward-digits 3
dial-peer voice 5 pots
translation-profile outgoing NATL
destination-pattern 9[2-9]......
port 0/0/0:23
forward-digits 7
dial-peer voice 6 pots
translation-profile outgoing NATL
destination-pattern 9707[2-9]......
port 0/0/0:23
dial-peer voice 7 pots
translation-profile outgoing NATL
destination-pattern 91[2-9]..[2-9]......
port 0/0/0:23
forward-digits 11
dial-peer voice 8 pots
translation-profile outgoing INTL
destination-pattern 9011T
port 0/0/0:23
prefix 011
voice translation-rule 10
rule 1 // // type any international plan any unknown

Similar Messages

In the Suite, how does the email portion handle spam?

In the Suite, how does the email portion handle spam?

Every email message you mark as spam (and also mark the ones that aren't spam that went in to your junk folder) helps it learn over time.
If you want more (extremely) technical information about it: http://en.wikipedia.org/wiki/Bayesian_spam_filtering

?? How does a G4 Quicksilver 2002 input S video from an S video VCR ??

?? How does a G4 Quicksilver 2002 input S-video from an S video VCR ??
I want to use some pre-miniDV S-video footage
in an upcoming small Final Cut production.
?? Is there a conversion from S-video to firewire400 ??
Best regards, Ken

Thanks Malcolm for the info.
At first, an El Gato like system seemed to be an answer.
However, I do not want any compromise
of the quality of my 25 minute video clips
as this quality is vital to the overall theme.
?? Will the El Gato or even the Canopus
try to compromise my clips without my instruction or control ??
Thanks very much for your thoughts on this.
Best Regards, Ken

HT201210 How does the Ipad get back to Nigerian Store from American Store to enable it carry out Update aand Downloading?

Dear All, please, How does the Ipad get back to Nigerian Store from American Store to enable it carry out Update and Downloading?

Try this.
Settings>iTunes and App Stores>Apple ID
Tap your ID
Tap View Apple ID
Enter your password
Go to country/region in the popup window to change the store

HT204053 How does one go about creating an icloud account from itunes ID?

How does one go about creating an icloud account from itunes ID? I don't seem to get past the reset password options for mi itunes ID.

You can't create an iCloud account on a PC. You must create the account on a Mac running Lion or newer, or an IOS device.

Cisco 2911 Voice Gateway SIP PSTN Calls Fail

Hello All,
    I am having trouble with outboud SIP PSTN calls through a Cisco 2911 Voice Gateway. 2911 VG terminates PSTN SIP Traffic and connects to Avaya CS1000M via QSIG PRI Trunks. When calls are attempted outbound fron the PBX the caller gets a fast busy. Debug ISDN q931 shows the call hitting the 2911 properly, debug voip ccapi inout shows the call matching the correct dial peers and debug ccsip shows the invite to the PSTN Provider SBC, however within the invite the "from" address incorrectly shows the calling number with the provider SBC address (see below). does anyone have any insight on how to correct this? Attached are VG config and Debug isdn q931, voip ccapi inout, ccsip messages and ccsip call. Thanks in advance for any help!!
From: <sip:[email protected]>:tag=6166CDC4-882
To: <sip:[email protected]>
Shawn C. Smith

i have same problem my cucm ip is 192.168.200.53
my Voice Gateway is SIP by ip 192.168.200.86 for internal
and 172.29.7.94
and my SIP Server is 10.208.9.69
if its oky can yuo take a look at my problem please
this is the syslog from debug
May 30 20:19:34.284: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
INVITE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 192.168.200.53:5060;branch=z9hG4bK3bd451bf17e0
From: "Aysar Mohamed" <sip:[email protected]>;tag=37693~244641b0-36ac-434c-91c1-823f25a68b28-18299026
To: <sip:[email protected]>
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
Supported: timer,resource-priority,replaces
Min-SE: 1800
User-Agent: Cisco-CUCM8.6
Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
CSeq: 101 INVITE
Expires: 180
Allow-Events: presence, kpml
Supported: X-cisco-srtp-fallback
Supported: Geolocation
Call-Info: <sip:192.168.200.53:5060>;method="NOTIFY;Event=telephone-event;Duration=500"
Cisco-Guid: 3047462016-0000065536-0000004549-0902342848
Session-Expires: 1800
P-Asserted-Identity: "Aysar Mohamed" <sip:[email protected]>
Remote-Party-ID: "Aysar Mohamed" <sip:[email protected]>;party=calling;screen=yes;privacy=off
Contact: <sip:[email protected]:5060>
Max-Forwards: 70
Content-Length: 0
May 30 20:19:34.284: //-1/B5A494800000/CCAPI/cc_api_display_ie_subfields:
   cc_api_call_setup_ind_common:
   cisco-username=2217156
   ----- ccCallInfo IE subfields -----
   cisco-ani=2217156
   cisco-anitype=0
   cisco-aniplan=0
   cisco-anipi=0
   cisco-anisi=1
   dest=90555769123
   cisco-desttype=0
   cisco-destplan=0
   cisco-rdie=FFFFFFFF
   cisco-rdn=
   cisco-rdntype=0
   cisco-rdnplan=0
   cisco-rdnpi=-1
   cisco-rdnsi=-1
   cisco-redirectreason=-1   fwd_final_type =0
   final_redirectNumber =
   hunt_group_timeout =0
May 30 20:19:34.288: //-1/B5A494800000/CCAPI/cc_api_call_setup_ind_common:
   Interface=0x30CF41D4, Call Info(
   Calling Number=2217156,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
   Called Number=90555769123(TON=Unknown, NPI=Unknown),
   Calling Translated=FALSE, Subscriber Type Str=Unknown, FinalDestinationFlag=TRUE,
   Incoming Dial-peer=0, Progress Indication=NULL(0), Calling IE Present=TRUE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, CLID Transparent=FALSE), Call Id=465
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: :cc_get_feature_vsa malloc success
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: cc_get_feature_vsa count is 1
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: :FEATURE_VSA attributes are: feature_name:0,feature_time:832953048,feature_id:85
May 30 20:19:34.288: //465/B5A494800000/CCAPI/cc_api_call_setup_ind_common:
   Set Up Event Sent;
   Call Info(Calling Number=2217156(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
   Called Number=90555769123(TON=Unknown, NPI=Unknown))
May 30 20:19:34.288: //465/B5A494800000/CCAPI/cc_process_call_setup_ind:
   Event=0x2B82D890
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_setupind_match_search:
   Try with the demoted called number 90555769123
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCallSetContext:
   Context=0x2ABC2E44
May 30 20:19:34.288: //465/B5A494800000/CCAPI/cc_process_call_setup_ind:
   >>>>CCAPI handed cid 465 with tag 0 to app "_ManagedAppProcess_Default"
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCallProceeding:
   Progress Indication=NULL(0)
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCallSetupRequest:
   Destination=, Calling IE Present=TRUE, Mode=0,
   Outgoing Dial-peer=802, Params=0x2ABC19D4, Progress Indication=NULL(0)
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCheckClipClir:
   In: Calling Number=2217156(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed)
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCheckClipClir:
   Out: Calling Number=2217156(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed)
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCallSetupRequest:
   Destination Pattern=9T, Called Number=0555769123, Digit Strip=FALSE
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccCallSetupRequest:
   Calling Number=2217156(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
   Called Number=0555769123(TON=Unknown, NPI=Unknown),
   Redirect Number=, Display Info=Aysar Mohamed
   Account Number=2217156, Final Destination Flag=TRUE,
   Guid=B5A49480-0001-0000-0000-11C535C8A8C0, Outgoing Dial-peer=802
May 30 20:19:34.288: //465/B5A494800000/CCAPI/cc_api_display_ie_subfields:
   ccCallSetupRequest:
   cisco-username=2217156
   ----- ccCallInfo IE subfields -----
   cisco-ani=2217156
   cisco-anitype=0
   cisco-aniplan=0
   cisco-anipi=0
   cisco-anisi=1
   dest=0555769123
   cisco-desttype=0
   cisco-destplan=0
   cisco-rdie=FFFFFFFF
   cisco-rdn=
   cisco-rdntype=0
   cisco-rdnplan=0
   cisco-rdnpi=-1
   cisco-rdnsi=-1
   cisco-redirectreason=-1   fwd_final_type =0
   final_redirectNumber =
   hunt_group_timeout =0
May 30 20:19:34.288: //465/B5A494800000/CCAPI/ccIFCallSetupRequestPrivate:
   Interface=0x30CF41D4, Interface Type=3, Destination=, Mode=0x0,
   Call Params(Calling Number=2217156,(Calling Name=Aysar Mohamed)(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
   Called Number=0555769123(TON=Unknown, NPI=Unknown), Calling Translated=FALSE,
   Subscriber Type Str=Unknown, FinalDestinationFlag=TRUE, Outgoing Dial-peer=802, Call Count On=FALSE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, tg_label_flag=0, Application Call Id=)
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: :cc_get_feature_vsa malloc success
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: cc_get_feature_vsa count is 2
May 30 20:19:34.288: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
May 30 20:19:34.288: :FEATURE_VSA attributes are: feature_name:0,feature_time:832952824,feature_id:86
May 30 20:19:34.292: //466/B5A494800000/CCAPI/ccIFCallSetupRequestPrivate:
   SPI Call Setup Request Is Success; Interface Type=3, FlowMode=1
May 30 20:19:34.292: //466/B5A494800000/CCAPI/ccCallSetContext:
   Context=0x2ABC1984
May 30 20:19:34.292: //465/B5A494800000/CCAPI/ccSaveDialpeerTag:
   Outgoing Dial-peer=802
May 30 20:19:34.292: //466/B5A494800000/CCAPI/cc_api_call_proceeding:
   Interface=0x30CF41D4, Progress Indication=NULL(0)
May 30 20:19:34.292: //465/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 192.168.200.53:5060;branch=z9hG4bK3bd451bf17e0
From: "Aysar Mohamed" <sip:[email protected]>;tag=37693~244641b0-36ac-434c-91c1-823f25a68b28-18299026
To: <sip:[email protected]>
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
CSeq: 101 INVITE
Allow-Events: telephone-event
Server: Cisco-SIPGateway/IOS-12.x
Content-Length: 0
May 30 20:19:34.292: //466/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Sent:
INVITE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 172.29.7.94:5060;branch=z9hG4bK461C
Remote-Party-ID: "Aysar Mohamed" <sip:[email protected]>;party=calling;screen=yes;privacy=off
From: "Aysar Mohamed" <sip:[email protected]>;tag=7394E4-1898
To: <sip:[email protected]>
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
Supported: timer,resource-priority,replaces,sdp-anat
Min-SE: 1800
Cisco-Guid: 3047462016-0000065536-0000004549-0902342848
User-Agent: Cisco-SIPGateway/IOS-12.x
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
CSeq: 101 INVITE
Timestamp: 1401481174
Contact: <sip:[email protected]:5060>
Call-Info: <sip:172.29.7.94:5060>;method="NOTIFY;Event=telephone-event;Duration=2000"
Expires: 180
Allow-Events: kpml, telephone-event
Max-Forwards: 69
Session-Expires: 1800
Content-Length: 0
May 30 20:19:34.300: //466/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 172.29.7.94:5060;branch=z9hG4bK461C
Call-ID: [email protected]
From: "Aysar Mohamed"<sip:[email protected]>;tag=7394E4-1898
To: <sip:[email protected]>
CSeq: 101 INVITE
Content-Length: 0
May 30 20:19:34.612: //466/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 183 Session Progress
Via: SIP/2.0/UDP 172.29.7.94:5060;branch=z9hG4bK461C
Record-Route: <sip:10.208.9.69:5060;transport=udp;lr>
Call-ID: [email protected]
From: "Aysar Mohamed"<sip:[email protected]>;tag=7394E4-1898
To: <sip:[email protected]>;tag=sbc0806eppk5yip-CC-57
CSeq: 101 INVITE
Contact: <sip:[email protected]:5060;user=phone>
Allow: INVITE,ACK,OPTIONS,BYE,CANCEL,REGISTER,INFO,PRACK,SUBSCRIBE,NOTIFY,UPDATE,MESSAGE,REFER
Content-Length: 328
Content-Type: application/sdp
v=0
o=- 17192647 17192647 IN IP4 10.208.9.69
s=SBC call
c=IN IP4 10.208.9.69
t=0 0
m=audio 39910 RTP/AVP 8 0 102 102 18 116
a=rtpmap:8 PCMA/8000
a=rtpmap:0 PCMU/8000
a=rtpmap:102 AMR/8000
a=rtpmap:102 AMR/8000
a=rtpmap:18 G729/8000
a=rtpmap:116 telephone-event/8000
a=ptime:5
a=fmtp:116 0-15
a=fmtp:18 annexb=yes
May 30 20:19:34.612: %SIP-3-UNSUPPORTED: Unsupported ptime value
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_caps_ind:
   Destination Interface=0x0, Destination Call Id=-1, Source Call Id=466,
   Caps(Codec=0x2, Fax Rate=0x2, Vad=0x1,
   Modem=0x0, Codec Bytes=160, Signal Type=2)
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_caps_ind:
   Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
   Playout Max=1000(ms), Fax Nom=300(ms))
May 30 20:19:34.612: //465/B5A494800000/CCAPI/cc_api_caps_ack:
   Destination Interface=0x0, Destination Call Id=-1, Source Call Id=465,
   Caps(Codec=g729r8(0x4), Fax Rate=FAX_RATE_VOICE(0x2), Vad=ON(0x2),
   Modem=OFF(0x0), Codec Bytes=20, Signal Type=2, Seq Num Start=3882)
May 30 20:19:34.612: //465/B5A494800000/CCAPI/cc_api_caps_ack:
   Destination Interface=0x0, Destination Call Id=-1, Source Call Id=465,
   Caps(Codec=g729r8(0x4), Fax Rate=FAX_RATE_VOICE(0x2), Vad=ON(0x2),
   Modem=OFF(0x0), Codec Bytes=20, Signal Type=2, Seq Num Start=3882)
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_event_indication:
   Event=170, Call Id=466
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_event_indication:
   Event Is Sent To Conferenced SPI(s) Directly
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_event_indication:
   Event=98, Call Id=466
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_event_indication:
   Event Is Sent To Conferenced SPI(s) Directly
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_call_cut_progress:
   Interface=0x30CF41D4, Progress Indication=INBAND(8), Signal Indication=SIGNAL RINGBACK(1),
   Cause Value=0
May 30 20:19:34.612: //466/B5A494800000/CCAPI/cc_api_call_cut_progress:
   Call Entry(Responsed=TRUE)
May 30 20:19:34.612: //465/B5A494800000/CCAPI/ccCallCutProgress:
   Progress Indication=INBAND(8), Signal Indication=SIGNAL RINGBACK(1), Cause Value=0
   Voice Call Send Alert=FALSE, Call Entry(Alert Sent=FALSE)
May 30 20:19:34.612: //465/B5A494800000/CCAPI/ccCallCutProgress:
   Call Entry(Responsed=TRUE)
May 30 20:19:34.612: //465/B5A494800000/CCAPI/ccConferenceCreate:
   (confID=0x30C11410, callID1=0x1D1, gcid=8C9E3127-E76E11E3-8274BE8C-EC3B12A0, tag=0x0)
May 30 20:19:34.616: //466/B5A494800000/CCAPI/ccConferenceCreate:
   (confID=0x30C11410, callID2=0x1D2, gcid=8C9E3127-E76E11E3-8274BE8C-EC3B12A0, tag=0x0)
May 30 20:19:34.616: //465/B5A494800000/CCAPI/ccConferenceCreate:
   Conference Id=0x30C11410, Call Id1=465, Call Id2=466, Tag=0x0
May 30 20:19:34.616: //465/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //466/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //465/B5A494800000/CCAPI/ccConferenceCreate:
May 30 20:19:34.616: ccConferenceCreate: ret1=0, codecMask1=2, bytes1=160, negot1=0, dtmf1=0
                    ret2=0, codecMask2=2, bytes2=160, negot2=1, dtmf2=6,
                    tx_dynamic_pt1=0, rx_dynamic_pt1=0, codec_mode1=0, params_bitmap1 =0
                    tx_dynamic_pt2=8, rx_dynamic_pt2=8, codec_mode2=0, params_bitmap2 =0
May 30 20:19:34.616: //465/B5A494800000/CCAPI/ccConferenceCreate:
   delay media to slow start case, codec negotation is not done
May 30 20:19:34.616: //465/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //465/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //465/B5A494800000/CCAPI/cc_api_bridge_done:
   Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=465,
   Destination Call Id=466, Disposition=0x0, Tag=0x0
May 30 20:19:34.616: //466/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //466/xxxxxxxxxxxx/CCAPI/cc_api_get_xcode_stream:
May 30 20:19:34.616: cc_api_get_xcode_stream : 4702
May 30 20:19:34.616: //466/B5A494800000/CCAPI/cc_api_bridge_done:
   Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=466,
   Destination Call Id=465, Disposition=0x0, Tag=0x0
May 30 20:19:34.616: //465/B5A494800000/CCAPI/cc_generic_bridge_done:
   Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=466,
   Destination Call Id=465, Disposition=0x0, Tag=0x0
May 30 20:19:34.616: //465/B5A494800000/CCAPI/ccConferenceCreate:
   Call Entry(Conference Id=0x16, Destination Call Id=466)
May 30 20:19:34.616: //466/B5A494800000/CCAPI/ccConferenceCreate:
   Call Entry(Conference Id=0x16, Destination Call Id=465)
May 30 20:19:34.616: //465/B5A494800000/CCAPI/cc_process_notify_bridge_done:
   Conference Id=0x16, Call Id1=465, Call Id2=466
May 30 20:19:34.616: //465/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 183 Session Progress
Via: SIP/2.0/UDP 192.168.200.53:5060;branch=z9hG4bK3bd451bf17e0
From: "Aysar Mohamed" <sip:[email protected]>;tag=37693~244641b0-36ac-434c-91c1-823f25a68b28-18299026
To: <sip:[email protected]>;tag=739628-1BDB
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
CSeq: 101 INVITE
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
Allow-Events: telephone-event
Remote-Party-ID: <sip:[email protected]>;party=called;screen=yes;privacy=off
Contact: <sip:[email protected]:5060>
Supported: sdp-anat
Server: Cisco-SIPGateway/IOS-12.x
Content-Type: application/sdp
Content-Disposition: session;handling=required
Content-Length: 233
v=0
o=CiscoSystemsSIP-GW-UserAgent 2639 5276 IN IP4 192.168.200.86
s=SIP Call
c=IN IP4 192.168.200.86
t=0 0
m=audio 18288 RTP/AVP 8 0 19
c=IN IP4 192.168.200.86
a=rtpmap:8 PCMA/8000
a=rtpmap:0 PCMU/8000
a=rtpmap:19 CN/8000
May 30 20:19:34.680: //466/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 500 Server Internal Error
Via: SIP/2.0/UDP 172.29.7.94:5060;branch=z9hG4bK461C
Record-Route: <sip:10.208.9.69:5060;transport=udp;lr>
Call-ID: [email protected]
From: "Aysar Mohamed"<sip:[email protected]>;tag=7394E4-1898
To: <sip:[email protected]>;tag=sbc0806eppk5yip-CC-57
CSeq: 101 INVITE
Reason: Q.850;cause=127;text="interworking unspecified"
Warning: 399 - "SoftX3000 R601-CCU Rel POS:[3103] Release from CR"
Content-Length: 0
May 30 20:19:34.680: //466/B5A494800000/CCAPI/cc_api_call_disconnected:
   Cause Value=41, Interface=0x30CF41D4, Call Id=466
May 30 20:19:34.680: //466/B5A494800000/CCAPI/cc_api_call_disconnected:
   Call Entry(Responsed=TRUE, Cause Value=41, Retry Count=0)
May 30 20:19:34.680: //465/B5A494800000/CCAPI/ccCallReleaseResources:
   release reserved xcoding resource.
May 30 20:19:34.680: //466/B5A494800000/CCAPI/ccCallSetAAA_Accounting:
   Accounting=0, Call Id=466
May 30 20:19:34.680: //465/B5A494800000/CCAPI/ccConferenceDestroy:
   Conference Id=0x16, Tag=0x0
May 30 20:19:34.680: //465/B5A494800000/CCAPI/cc_api_bridge_drop_done:
   Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=465,
   Destination Call Id=466, Disposition=0x0, Tag=0x0
May 30 20:19:34.680: //466/B5A494800000/CCAPI/cc_api_bridge_drop_done:
   Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=466,
   Destination Call Id=465, Disposition=0x0, Tag=0x0
May 30 20:19:34.680: //465/B5A494800000/CCAPI/cc_generic_bridge_done:
   Conference Id=0x16, Source Interface=0x30CF41D4, Source Call Id=466,
   Destination Call Id=465, Disposition=0x0, Tag=0x0
May 30 20:19:34.680: //466/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Sent:
ACK sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 172.29.7.94:5060;branch=z9hG4bK461C
From: "Aysar Mohamed" <sip:[email protected]>;tag=7394E4-1898
To: <sip:[email protected]>;tag=sbc0806eppk5yip-CC-57
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
Max-Forwards: 70
CSeq: 101 ACK
Allow-Events: kpml, telephone-event
Content-Length: 0
May 30 20:19:34.684: //466/B5A494800000/CCAPI/ccCallDisconnect:
   Cause Value=41, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=41)
May 30 20:19:34.684: //466/B5A494800000/CCAPI/ccCallDisconnect:
   Cause Value=41, Call Entry(Responsed=TRUE, Cause Value=41)
May 30 20:19:34.684: //466/B5A494800000/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x30CF41D4, Tag=0x0, Call Id=466,
   Call Entry(Disconnect Cause=41, Voice Class Cause Code=0, Retry Count=0)
May 30 20:19:34.684: //466/B5A494800000/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
May 30 20:19:34.684: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
May 30 20:19:34.684: :cc_free_feature_vsa freeing 31A5D9F0
May 30 20:19:34.684: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
May 30 20:19:34.684: vsacount in free is 1
May 30 20:19:34.684: //465/B5A494800000/CCAPI/ccCallDisconnect:
   Cause Value=41, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
May 30 20:19:34.684: //465/B5A494800000/CCAPI/ccCallDisconnect:
   Cause Value=41, Call Entry(Responsed=TRUE, Cause Value=41)
May 30 20:19:34.684: //465/B5A494800000/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 503 Service Unavailable
Via: SIP/2.0/UDP 192.168.200.53:5060;branch=z9hG4bK3bd451bf17e0
From: "Aysar Mohamed" <sip:[email protected]>;tag=37693~244641b0-36ac-434c-91c1-823f25a68b28-18299026
To: <sip:[email protected]>;tag=739628-1BDB
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
CSeq: 101 INVITE
Allow-Events: telephone-event
Server: Cisco-SIPGateway/IOS-12.x
Reason: Q.850;cause=41
Content-Length: 0
May 30 20:19:34.684: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
ACK sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 192.168.200.53:5060;branch=z9hG4bK3bd451bf17e0
From: "Aysar Mohamed" <sip:[email protected]>;tag=37693~244641b0-36ac-434c-91c1-823f25a68b28-18299026
To: <sip:[email protected]>;tag=739628-1BDB
Date: Fri, 30 May 2014 20:19:34 GMT
Call-ID: [email protected]
Max-Forwards: 70
CSeq: 101 ACK
Allow-Events: presence, kpml
Content-Length: 0
May 30 20:19:34.688: //465/B5A494800000/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x30CF41D4, Tag=0x0, Call Id=465,
   Call Entry(Disconnect Cause=41, Voice Class Cause Code=0, Retry Count=0)
May 30 20:19:34.688: //465/B5A494800000/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
May 30 20:19:34.688: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
May 30 20:19:34.688: :cc_free_feature_vsa freeing 31A5DAD0
May 30 20:19:34.688: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
May 30 20:19:34.688: vsacount in free is 0
May 30 20:19:36.044: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
OPTIONS sip:172.29.7.94:5060 SIP/2.0
Via: SIP/2.0/UDP 10.208.9.69:5060;branch=z9hG4bKmisco3ykfiooegpygsphkocp1T20326
Call-ID: isbcfemyk1p1mkteets1tcmi53eeehfhikcp@SoftX3000
From: <sip:172.29.7.94:5060>;tag=sbc0803k1pyk51o
To: <sip:172.29.7.94>
CSeq: 1 OPTIONS
Max-Forwards: 70
Content-Length: 0
May 30 20:19:36.048: //467/8DAABF6C8278/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 200 OK
Via: SIP/2.0/UDP 10.208.9.69:5060;branch=z9hG4bKmisco3ykfiooegpygsphkocp1T20326
From: <sip:172.29.7.94:5060>;tag=sbc0803k1pyk51o
To: <sip:172.29.7.94>;tag=739BBC-1CE2
Date: Fri, 30 May 2014 20:19:36 GMT
Call-ID: isbcfemyk1p1mkteets1tcmi53eeehfhikcp@SoftX3000
Server: Cisco-SIPGateway/IOS-12.x
CSeq: 1 OPTIONS
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
Allow-Events: telephone-event
Accept: application/sdp
Supported: 100rel,timer,resource-priority,replaces,sdp-anat
Content-Type: application/sdp
Content-Length: 446
v=0
o=CiscoSystemsSIP-GW-UserAgent 3496 1601 IN IP4 172.29.7.94
s=SIP Call
c=IN IP4 172.29.7.94
t=0 0
m=audio 0 RTP/AVP 18 0 8 9 4 2 15
c=IN IP4 172.29.7.94
m=image 0 udptl t38
c=IN IP4 172.29.7.94
a=T38FaxVersion:0
a=T38MaxBitRate:9600
a=T38FaxFillBitRemoval:0
a=T38FaxTranscodingMMR:0
a=T38FaxTranscodingJBIG:0
a=T38FaxRateManagement:transferredTCF
a=T38FaxMaxBuffer:200
a=T38FaxMaxDatagram:320
a=T38FaxUdpEC:t38UDPRedundancy
My SIP GW internal ip address is 192.168.200.86
and the Public IP is : 172.29.7.94
My CUCM is 192.168.200.53
my GW Config is :
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
sip
registrar server
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
codec preference 3 g729r8
codec preference 4 g729br8
voice translation-rule 3
rule 1 /^9/ /\1/
voice translation-rule 4
rule 4 /^22217/ /7/
rule 5 /^2217/ /7/
rule 6 /^022217/ /7/
rule 7 /^0122217/ /7/
voice translation-rule 5
rule 1 /^5/ /905/
rule 2 /^1/ /901/
rule 3 /^2/ /902/
rule 4 /^3/ /903/
rule 5 /^4/ /904/
rule 6 /^6/ /906/
rule 7 /^7/ /907/
rule 8 /^8/ /908/
rule 10 /^00/ /900/
rule 11 /'+'/ /900/
voice translation-profile OUT
translate called 3
voice translation-profile REDIAL
translate calling 5
voice translation-profile SIP-NEW
translate called 4
application
service mva http://192.168.200.53:8080/ccmivr/pages/IVRMainpage.vxml
service ccm http://192.168.200.53:8080/ccmivr/pages/IVRMainpage.vxml
license udi pid CISCO2921/K9 sn FCZ164960G0
hw-module pvdm 0/0
hw-module pvdm 0/1
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address 192.168.200.86 255.255.255.0
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 172.29.7.94 255.255.255.252
duplex auto
speed auto
ip http server
ip http access-class 23
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip route 0.0.0.0 0.0.0.0 192.168.200.1
ip route 10.208.9.0 255.255.255.0 172.29.7.93
access-list 23 permit 10.10.10.0 0.0.0.7
control-plane
mgcp profile default
sccp local GigabitEthernet0/0
sccp ccm 192.168.200.53 identifier 1 priority 1 version 7.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 2 register NAGHI-MTP
dspfarm profile 2 mtp
codec g711alaw
maximum sessions hardware 25
associate application SCCP
dial-peer voice 802 voip
description ** SIP TO STC **
translation-profile outgoing OUT
destination-pattern 9T
session protocol sipv2
session target ipv4:10.208.9.69:5060
session transport udp
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay sip-notify rtp-nte sip-kpml
no vad
dial-peer voice 811 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.53
incoming called-number 022217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 812 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.53
incoming called-number 22217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 813 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.53
incoming called-number 2217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 814 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
preference 1
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.63
incoming called-number 022217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 815 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
preference 1
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.63
incoming called-number 22217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 816 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
preference 1
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.63
incoming called-number 2217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 817 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.53
incoming called-number 0122217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
dial-peer voice 818 voip
description ** SIP INCOMING FROM STC **
translation-profile incoming SIP-NEW
translation-profile outgoing REDIAL
preference 1
destination-pattern 7...
session protocol sipv2
session target ipv4:192.168.200.63
incoming called-number 0122217...$
dtmf-relay sip-notify rtp-nte sip-kpml
codec g711alaw
Please i need ur help ASAP

How does it cost to take unlimited call subscripti...

Hello, I want to take unlimited call subscription to usa so anyone tell me how much skype cost to take unlimited call subscription? It's shows $6.99/month but when I try to pay through cards it shows €4,99 what this means it's €499 or €4.99 please explane it, how much skype will charge? €4,99 or €4.99?

By default your currency is set to EUR and 4.99EUR is about the same as 6.99USD. (Depending on currency exchange rate at the time)
Unlimited US is 6.99USD or 4.99EUR depending on your currency. If you wish you can change your currency to USD from your account: https://secure.skype.com/account/
https://support.skype.com/en-us/faq/FA499/In-which-currency-can-I-make-payments
Andre
If answer was helpful please mark it with Kudos and if issue is resolved mark it with solution. This will help other users find this answer more easily. Thanks in advance!

How does the iPhone 3G handle this???

If I save photos from my email, and there are multiple photos with the same name, how does the iPhone 3g behave? Since I can't see the filenames of the photos, I am unable to determine if any two images have the same filename.
Does the phone rename one? Overwrite one? What occurs??

That is exactly what I was talking about. I expected as much however I noticed the following occur. I save a photo from one source, and saved the exact same photo from another source (both have the same filename) I then deleted the first one that I saved, and both photos were deleted.
Is that the proper behavoire?

Handling incoming caller ID from legacy PBX

Hello,
At my company we're currently in the process of running Lync 2010 EV through a POC. Everything is working great at the moment except for incoming caller ID from the legacy PBX. When a call comes into Lync from the legacy PBX (either from a desk phone or
from outside the company), the legacy PBX replaces the actual 'from' number with the company's main number. Apparently this is due to the legacy PBX being old and masking the outbound caller ID information at a global level. (So basically ANY call that goes
outbound from the legacy PBX has the caller ID masked with the main number, no way to make exclusions. This has been verified by the vendor that services the legacy PBX.)
The problem this introduces on the Lync client is that in the address book everyone has the company's main number as their phone number, except with an extension at the end. So when a call comes in from the legacy PBX the Lync client quite literally randomly
picks someone from the address book and says the call is coming from the randomly picked person.
So far in my attempts to fix this, I've tried creating a contact in AD with a phone number of just the main number. This did not change anything from the Lync clients perspective, however when I miss a call that was sent from the legacy PBX, Outlook now
indicates that the missed call is from the contact object with the main number instead of saying I missed a call from some random person from the address book.
I've also looked into seeing if a MSPL script could intercept incoming audio requests and change the From parameter to something else if the From value was the main number. So far I haven't seen any examples of this, nor do I have a test environment to test
MSPL scripts in yet.
Does anyone have any suggestions on what can be done for the POC we're trying to do? Obviously if (more like 'when' really...) we decide to move everything over to Lync EV and pull the plug on the legacy PBX this won't be an issue, but right now I can't
even move forward with doing a POC outside of my team until I figure out something to do with the inbound caller ID.
Thanks,
Cody

How are you connected to the legacy PBX? It might be easier to put a modification in a gateway if you're using one.
Also, why Lync 2010 instead of 2013?
What do you have set for the lineURIs of the users? Is it the main number with extensions or a DID?
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
SWC Unified Communications

Can't establish a Voice gateway (cisco 2911) using SIP with CUCM 9.1

I have configured a Cisco 2911 as a Voice Gateway using SIP (the configuration is attached), but unfortunately can't establish a test call to a phone (CUPC 8.6 SCCP) using csim start. I have done logging the ccsip debug and ccapi debug and attached them. Could anyone help me to solve this problem?

I just did some research on my end and csim is not supported for SIP. The Invite will never be created and sent to the CUCM to initate the call. It disconnects in the router itself with normal cause.
*Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Error/sipSPIOutgoingCallSDP:
Could not create source SDP for Outgoing Call
*Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Error/sipSPICreateOutboundSDP:
Error in creating an SDP for the outbound call - Check for supported codecs
*Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Error/preprocessSetup:
Error during outbound SDP creation
*Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Info/sipSPIInitiateDisconnect: Initiate call disconnect(16) for outgoing call
Please use an actual call to test your dial-peer and integration with call manager. csim will not work.
Hantale
Sree

How does Goods Issue know which Batches to deallocate from A/R Credit Memo?

Hi,
I am creating an addon that runs after a A/R Credit Memo is created. It creates a Goods Issue, and enters the Item Code and the Quantity from the line items on the Credit Memo into the Goods Issue.
After it writes the Goods Issue to SAP, I open up the document it created and see that the line items are in there correctly, and that somehow the batches assigned to those line items are also in there.
There is nothing in the code that does anything with the Batches, but somehow SAP knows which batches to work with.
I haven't been able to find any info about it. Can you please help us understand what is happening? How does SAP know and make assignments to batches in line items in Goods Issues?
Thank you,
Mike

Hi Michael and Gordon,
Sorry Gordon, I'm quite sure you misunderstood Michael original question. Michael asked how the add-on he created could link corresponding batch number from an A/R Credit Memo document could be selected by Goods Issue document which generated by the add-on, while he actually never wrote a code to select any batches numbers which available in the system.
Maybe a little bit of illustration:
1. Item A, qty 10 - (batch A qty 5, batch B qty 3, batch C qty 2)
2. A/R Credit Memo occurred, return of Item A with 3 qty (batch A qty 1, batch B qty 1, batch D qty 1). Therefore, item A latest position should be (batch A qty 6, batch B qty 4, batch C qty 2, batch D qty 1). This A/R Credit Memo created by add-on.
3. Goods Issue document triggered by add-on. The problem is, Michael never write any code to select any batch numbers, and somehow the system choose batch number precisely as occurred in number 2 (A/R Credit Memo document), which is (batch A qty 1, batch B qty 1, batch D qty 1). Therefore the stock position for Item A back to as being displayed in number 1.
I believe this shouldn't be possible at all. Unless, there is a certain mechanism in SAP that automatically choose batch number to used in Goods Issue document using LIFO (Last In First Out), which is, as far as I know never exist in any SAP B1 version. Yes you could automatically choose batch numbers according to available batch, but you could do this when system prompt you when you tried to issue certain document using SAP application itself, not using add-on.
And of course, you could write a code to choose certain batches based on certain A/R Credit Memo, but still, you need to write a code, you can't do this without a code, selection of batches is compulsory when you tried to add a goods issue document which consist of items that managed using batches.
In my opinion, I think it is better for you to re-write those codes and relate batches you want to attach with your Goods Issue document based on corresponding A/R Credit Memo. It is much safer, and the error message you encountered won't happen again in the future.
Best Regards,
Hendry Wijaya

How does one prevent a column in a database from being visable to end users

I have a password column I would like to hide by default from any one with query access. How does one do this?

If you're on 10G you can use encryption.
First create a wallet en create the master encryption key with:
alter system set encryption key identified by "<secretpwd>";
Then you can encrypt a column in a table with the command:
alter table <tablename> modify <column> encrypt;
If the wallet is open you can query the column. If the wallet is closed you cannot query the column ....
Grtx

How does 3.1's new "Genius Mix" differ from a Genius Playlist?

Hey guys I still haven't updated to 3.1 because of all the complaints and issues associated with it, but I was curious about one feature I'm missing out on... How does the new Genius Mix any different than an automated Genius Playlist that is made when you turn on Genius on your iPhone???
Genius just collects up to 25 songs by different artists in the same genre... What does Genius Mix do differently?
Thanks to anybody who answers me... I'm just curious, that's all.

Genius mixes are created in iTunes 9. It's like Genius, but different. Genius mixes come automatically.
"This new feature searches your iTunes library, finds songs that go great together, and creates multiple mixes you’ll love. All automatically. These mixes are like channels programmed entirely with your music. You may discover songs you never knew you had — and rediscover forgotten favorites."
iTunes will create up to 12 Genius mixes, like Rock Mix 1, Rock Mix 2, Oldies Mix, Alternative
Mix, etc. These are like radio stations created from your own music. The songs in the mix can't can't be listed.
Go here and scroll down to Genius Mix. http://www.apple.com/itunes/whats-new/

How does the Delta functionality works while updating Infocube from PA

Hi Gurus
How does the Delta functionality works when you send forecast to the Info cube from the Planning Area.
As I have weekly based planning, every week we have to update the forecast into the Cube. If I update every week into the Cube , then the values are going to append in the Info cube.
Shall I create ODS in between the Planning area and the Info cube .
(or)
Any other method ?
Please Suggest.

Hi Preetham,
Data Extraction from planning area to infocube usually its supports for full update only, when u r going to load the data from planning area to cube ,it deletes the previous data and u vil get the fresh data, this is the best method performance wise,
if u want to use the delta functionality u can go for planning area to Dso, Dso to cube, it vil supports the delta functionality, but it vil degrades the system performance,
regards
ravi

How can i reset another page when call it from a page

I use JDeveloper 10.3 to develop my application. And I want to reset value of UI component (inputtex, selectInputDate . . .) of a page when i call it from another page.
Thanks!

You can execute a method in "backing bean/Application module" on page load which can set the value of the UI components. Following link can help you to
[http://kohlivikram.blogspot.com/2008/10/call-method-on-page-load-in-adf.html|http://kohlivikram.blogspot.com/2008/10/call-method-on-page-load-in-adf.html] .
~Vikram

How does a voice gateway handle a call received from CUCM?

Similar Messages

Maybe you are looking for