How i can configure the time of response between two APs if one of they "fail" for the reconnection for customers?

Hi
I whis to know how i can configure the WLC (2500) for reduce the time of responce between Two Lightweight APs (1040 and 1602) if one of they are disconnected for any reason (energy, malfunction, etc.) for the reconnection of the clients.
I realized the next test: I have 2 APs connected, connect my laptop to the AP 1602 and start to making a TFTP transfer between my laptop and a server, then disconnect the AP 1602 and showing the laptop, the laptop makes the change to AP 1040, but the connection to the service, the TFTP transfer is cut because it takes about 30 seconds to resume the connection with the network
How i can reduce this time, because my clients want their connection is not lost when passing a situation similar, i look in the pages of cisco but did not find any information pudisese help me, any help is welcome.
thank you very much in advance
Jonathan

Not much you can do as its up to the client card to know it has no network connectivity and then to try to associate and obtain a DHCP address again. This is client dependent.
Sent from Cisco Technical Support iPhone App

Similar Messages

  • How I can configure my Time Capsule with my mobile me?

    Someone know how i can configure my Time Capsule with my mobile me?... Because i need access to my documents remotely, from any place where I find...
    (sorry my bad english)

    I think you're referring to the Back To My Mac feature?
    Follow these three articles. Most important are the second and third.
    http://www.apple.com/mobileme/features/mac.html
    http://support.apple.com/kb/ht1109
    http://support.apple.com/kb/HT3486

  • Can I use Facetime between two devices which both are signed in to the same Apple ID?

    Can I use Facetime to communicate between two Apple devices which are each signed into the same Apple ID?

    Chris CA wrote:
    Phil0124 wrote:
    Yes.
    No.
    And use the new address to call that device.
    What new address?
    Perhaps you mean the OP needs to add a new email address for his AppleID and use that email address.
    Yes. That's what I meant.
    Change the "You can de Reached by Facetime At" for one of them under Settings->Facetime->You can be Reached by Facetimer At.
    I probably should have specified "Change the "You can de Reached by Facetime At"(email address) ...
    NOW TO CORRECT:  Even though I said you could, you can't.
    I tried this out just now and you can't facetime a device using the same Apple ID.
    So yes, you infact need another Apple ID for this. Not just another email address.
    My Bad. sorry.  I don't deserve the 10 points.

  • I wanted to know how do you calculate the number of days between two dates

    i wanted to know how do you calculate the number of days between two dates in java ? i get both the dates from the database. i guess there are many issues like leap year and Febuary having diff no of months ..etc.

    thanks..
    I solve my problem as
    public class MyExample {
        public static void main(String a[]) {
            String stdate = "2009-03-01";
            java.sql.Date currentDate = new java.sql.Date(System.currentTimeMillis());
            java.sql.Date preDate = java.sql.Date.valueOf(stdate);
            System.out.println(currentDate);
            System.out.println(preDate);
    //        int dateCom = preDate.compareTo(currentDate);
    //        System.out.println(dateCom);
            long diff = currentDate.getTime() - preDate.getTime();
            int days = (int) Math.floor(diff / (24 * 60 * 60 * 1000));
             System.out.println(days);
    }

  • How we can configure new pricing procedure at the time of billing document

    Hi SD Gurus,
    Can u plz tell me how we can configure new pricing procedure at the time of billing document level.
    Thanks & Regards,
    Sreenivas.P

    Hello,
    Why?
    The sales order confirms the price given to the customer.  If you have re-determined a new price/discount then you may consider in VTFL to use pricing type C.
    Regards
    Waza

  • How I can configure 2 EP 7.0 server for SSO with ECC 6.0?

    Hi,
    How I can configure 2 EP 7.0 server for SSO by using SAP Logon ticket with same ECC 6.0 back end?
    Developement EP 7.0 SP14 is already configure with ECC 6.0 back end now I want to configure my local EP 7.0 SP9 (Sneak Preview) server with same ECC 6.0 Development.
    How I can acheive this?
    I really appreciate if some one guide me.
    Thanks.
    Ashish.

    Hi,
    You have to follow the SSO steps.
    1.Create RFC Destination in SM59
    2.Create RFC Destination in Visual admin
    3.Export verify.der certificate from portal
    4.Import verify.der certificate to R/3
    5.Create system alias
    6.Export R/3 certificate from R/3
    7.Import R/3 certificate to portal
    8.Maintain the SSO parameters in RZ10
    Please check the below link also.
    http://help.sap.com/erp2005_ehp_03/helpdata/EN/4d/dd9b9ce80311d5995500508b6b8b11/frameset.htm
    Regards,
    Bala.

  • Since the last update of firefox, the time has been 25 to 35 seconds to enter bookmarks or even the time it takes to page down when it used to take a few seconds. can you check why it taking so long since the update on firefox.

    since the last update a few days ago of firefox, the time has been 25 to 35 seconds to enter bookmarks or even the time it takes to page down when it used to take a few seconds. can you tell me why it taking so long since the update on firefox. may another update is in order.

    I have now done pretty much every suggestion that even vaguely applies in the various helpful link provided. Thanks for the ongoing help. =)
    I have managed to get FireFox's start-up memory usage down to about 100,000K, however it appears that memory usage keeps creeping up the longer FireFox is open. (It seems to top out around 500,000K.) And I'm not talking open for many hours or days - but rather for minutes and possibly up to a couple hours. (Based on how long I've been fiddling with all this so far.)
    On the plus side, it does not appear GreaseMonkey is the culprit since with it active or disabled this memory creep still occurs. Although having GreaseMonkey enabled definitely increases the rate of memory creep. Though once it has creeped up to 150,000+K, disabling GM does not make it drop back down to the starting 100,000K.
    I should point out I run a MacBook Pro and use Bootcamp to partition the hard drive and run it as a Windows 7 PC about half the time. I am running it literally as a PC or, alternately, as a Mac depending on which hard drive I choose to load. (I'm not "windowing" it.) This problem exists regardless of whether I am using the PC or the Mac. These repairs have been made currently on the PC side, and I will attempt them all again on the Mac side. I find it odd that this enormous memory drain has occurred on 3 different computers at the same time. (The two "halves" of my home laptop as well as the PC at my work place.)

  • How i can configure my sql server?

    how i can configure my remote sql server can u plse tell me

    Hi,
    I am assumung that you are in a situation where you want to connect to remore MS SQL server and you are on windows.
    In this case its simple machine on which you are running java code you can create DSN to remote machine and use the jdbc:odbc.
    Hope this helps
    Akash Mavle
    www.solversa.com

  • How I can lock my Time Capsule on specific MAC addresses?

    How I can lock my Time Capsule on specific MAC addresses?

    Ok, you mean MAC filtering..
    This is called timed access on the airport utility..
    Set no access for all other wireless.
    Then add for your own.
    Setup all the computers that you want to have access and whatever the time..
    You can only MAC filter wireless clients not wired.
    Do a search if this is not enough for posts by Bob Timmons on Timed Access.

  • Hello there - how can I share my iTunes library between two users on the same computer? I put the library in a shared folder between both and have selected this library on both as well, but when I update iTunes with music etc it only appears on one?

    Hello there - how can I share my iTunes library between two users on the same computer? I put the library in a shared folder between both and have selected this library on both as well, but when I update iTunes with music etc it only appears on one?

    Thank you Joe - I tried this but it's only showing a teensy amount of music - the stuff on the second users account as opposed to the giagntic library on the 'main' account. I actually went to a Genius Bar and they said that apple doesn't really want you to share music between accounts - parents don't want to hear their kids music etc. Which seemed strange, but it might be the case sadly   Thanks anyway!

  • HT204380 How i can install face time for my iPhone 4s & iPad 2 . Im living in UAE

    How i can install face time for my iPhone 4s & iPad 2 . Im living in UAE

    FaceTime has been banned in UAE, it can not be installed.  

  • Increase the time of response of my queries

    Hi, I have a db2 as database on AS400 and I would like to increase the time of response of my queries because in a table I have more of one million records.
    I select a part of this record (select * from sergt where wbtruc='A735') but to get this record where wbtruc=A735 it read the whole table so more of one million records.
    is it posssible that it read a part of table and not the whole table
    or you are another solution to increase the time of response ?
    Thanks in advance?

    Uh, oh, temporary index for 1 million records sounds
    like OutOfMemoryError :)If this query is going to be run regularly then an access path should be created on the AS400 to support it. An access path over 1 million records isn't a big deal there, the largest file we have is about 120 million records with two access paths and I'm sure there are much much bigger files in the AS400 world.

  • I lost all the information in the ical. I am using icloud and info desapear from ical and several times from my agenda too. But I desperately need the info from my ical. I tried using the time machine but i received a messagem saying that they can not mod

    I am using icloud and info desapear from ical and several times from my agenda too.
    But I desperately need the info from my ical.
    I tried using the time machine but i received a messagem saying that they can not modify ical.
    Can somebody help me?

    First of all, we are not Adobe.  This is a user to user forum.  We are consumers just like you. And I have arthritis, too, although not severe.
    Now let's see if we can help you resolve your problem.
    Where was it purchased from?
    Was it downloaded or was a disc purchased?
    What is your operating system?
    Is it version Photoshop Elements 13?
    Did you use a redemption code to get a serial number?
    Did you sign in/activate?
    Did you create an Adobe account?

  • How can I insert a vertical line  between two underlined unfilled with text lines.  I am trying to construct an invoice and I need a break.  If I try any of the shapes or inset functions it eliminates my underlined lines and shifts the whole document.

    I am trying to construct an invoice.  How can I install a vertical line between two or more underlined lines to create a break.  I have tried the insert, shapes and nothing works.  If I try any of the functions the whole document shifts to the right and I loose some of the lines.  Is there a work around, or is I work not able to do what I want?   
    Thanks
    Armand

    It sounds as though you may have "Object Causes Wrap" activated for the Line Shape. This will push other content away.
    See the Wrap Inspector.
    Jerry

  • Can you access Time Capsule From any where, or do you have to be on the same network

    Can you access Time Capsule From any where, or do you have to be on the same network

    check out the post by Tesserax in this discussion.

Maybe you are looking for