How to check current input/output rate on router subintenterface via SNMP?

How to check current input/output rate on router (2821, etc..) subintenterface via SNMP, like cacti monitoring system.
I cant find OID to make this with snmpwalk.
Or there is no way to check current load by this way? Only polling?
P.S. Ethernet subinterface, of course.
With great respect, S.A.

Hi,
Try to use:
1.3.6.1.4.1.9.2.2.1.1.6 - InBitRate
1.3.6.1.4.1.9.2.2.1.1.8 - OutBitRate
1.3.6.1.4.1.9.2.2.1.1.28 - ifDescription

Similar Messages

How to check current PulseAudio sampling rate and other parameters?

# pacmd list-sinks
Daemon not responding.
http://askubuntu.com/questions/299597/g … d-bit-rate

lucke wrote:Did it mention having permission denied to /run/user/1000? If so, "chown bbarcher.users /run/user/1000" and perhaps "pkill pulseaudio; pulseaudio &".
On pulse restart I get
Unable to contact D-Bus session bus
And a whole galore of errors.

OBIEE11g: How to check current environment installed/applied patches?

Hi all,
Does anyone know how to check current OBIEE environment installed/applied patches? I don't have the patch installs anymore and now trying to figure out how to view them. My current environment is OBIEE 11.1.1.5.
Thank you in advance!

To check Patches applied, do changes where ever required.
Use this command
cd $FMW_HOME/Oracle_BI1
opatch lsinventory|grep applied
In Windows from C:\OFM\Oracle_BI1\OPatch
Use this command
opatch lsinventory applied
opatch.bat lsinventory –oh <EPM_ORACLE_HOME> –jdk <MIDDLEWARE_HOME>/jdk160_21
To check the version login to Answers-> Administration you can find the version a top use weblogic user to see.
Appreciate if you mark as correct/helpful

Ser. Int. 5 min Input/Output Rate

Dear Net Pros,
On my serial interface of my AS 5350, I am having the following output as given below. The 5 minute input rate is half of the 5 minute output rate. Can someone suggest how I can fix this problem. I am currently also having access-lists configured in my gateway. Need some solution at the earliest possible.
Serial0/0 is up, line protocol is up
Hardware is DSCC4 Serial
Internet address is 61.11.227.114/30
MTU 1500 bytes, BW 8192 Kbit, DLY 20000 usec,
reliability 255/255, txload 11/255, rxload 5/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 05:49:59
Queueing strategy: fifo
Output queue 0/4096, 8898 drops; input queue 0/4096, 0 drops
5 minute input rate 162000 bits/sec, 240 packets/sec
5 minute output rate 373000 bits/sec, 718 packets/sec
6151942 packets input, 515269067 bytes, 0 no buffer
Received 2447 broadcasts, 0 runts, 0 giants, 0 throttles
39 input errors, 8 CRC, 31 frame, 0 overrun, 0 ignored, 0 abort
17398133 packets output, 1121504239 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Rushabh

Here is the Gateway Config for you:
AS5350_1#sh run
Building configuration...
Current configuration : 11303 bytes
! Last configuration change at 01:30:05 UTC Mon Dec 15 2003
! NVRAM config last updated at 01:30:08 UTC Mon Dec 15 2003
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec localtime
service password-encryption
hostname AS5350_1
boot system flash c5350-is-mz.122-2.XB6.bin
no boot startup-test
logging buffered 30000 debugging
aaa new-model
aaa group server radius mind
server 202.183.221.215 auth-port 1645 acct-port 1646
server 61.11.231.122 auth-port 1645 acct-port 1646
aaa authentication login default local
aaa authentication login h323 group mind
aaa authorization exec h323 group mind
aaa accounting network h323 start-stop group mind
aaa accounting connection h323 start-stop group mind
aaa session-id common
resource-pool disable
spe country e1-default
spe 1/00 2/09
firmware location flash:np.8.8.1.spe
ip subnet-zero
ip cef
no ip domain-lookup
voice class codec 1
codec preference 1 g723r63 bytes 48
codec preference 2 g723ar63
codec preference 3 g723ar53
codec preference 4 g729r8
mta receive maximum-recipients 0
dial-control-mib retain-timer 1000
dial-control-mib max-size 1200
controller E1 3/0
framing NO-CRC4
ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled ani
cas-custom 1
country china
category 2
answer-signal group-b 1
dnis-digits min 1 max 9
groupa-callerid-end
controller E1 3/1
framing NO-CRC4
ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled ani
cas-custom 1
country china
category 2
answer-signal group-b 1
dnis-digits min 1 max 9
groupa-callerid-end
controller E1 3/2
framing NO-CRC4
ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled ani
cas-custom 1
country china
category 2
answer-signal group-b 1
dnis-digits min 1 max 9
groupa-callerid-end
controller E1 3/3
framing NO-CRC4
ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled ani
cas-custom 1
country china
category 2
answer-signal group-b 1
dnis-digits min 1 max 9
groupa-callerid-end
gw-accounting h323
gw-accounting syslog
gw-accounting h323 vsa
gw-accounting voip
translation-rule 1
Rule 0 ^111856 0
translation-rule 2
Rule 0 ^112856 0
translation-rule 3
Rule 0 ^113856 0
interface FastEthernet0/0
ip address x.x.x.x 255.255.255.248
ip access-group 101 in
ip accounting output-packets
ip route-cache flow
duplex auto
speed auto
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial0/0
ip address x.x.x.x 255.255.255.252
ip access-group 101 in
ip accounting output-packets
no cdp enable
interface Serial0/1
no ip address
shutdown
clockrate 2000000
ip classless
ip route 0.0.0.0 0.0.0.0 61.11.227.113
ip http server
logging 61.11.231.122
access-list 101 permit ip 202.183.221.208 0.0.0.15 any
access-list 101 permit ip 61.11.231.120 0.0.0.7 any
access-list 101 permit ip host 64.50.72.85 any
access-list 101 permit ip host 210.55.9.194 any
access-list 101 permit ip host 64.50.72.123 any
access-list 101 permit ip host 203.144.226.198 any
access-list 101 permit ip host 66.15.38.214 any
access-list 101 deny tcp any any
access-list 101 deny udp any any
access-list 101 deny ip any any
snmp-server community CSCO14344 RW
snmp-server trap-source FastEthernet0/0
snmp-server packetsize 8192
no snmp-server enable traps tty
radius-server host 202.183.221.215 auth-port 1645 acct-port 1646 key 7 0822455D0
A16081E1C0F
radius-server host 61.11.231.122 auth-port 1645 acct-port 1646 key 7 094F471A1A0
A1A1B0508
radius-server retransmit 3
radius-server authorization permit missing Service-Type
radius-server vsa send accounting
radius-server vsa send authentication
call rsvp-sync
call application voice debit tftp://61.11.231.122/app_debitcard.2.0.2.8.tcl
call application voice debit uid-len 6
call application voice debit pin-len 6
call application voice debit language 1 en
call application voice debit set-location en 0 tftp://61.11.231.122/prompts/en/
voice-port 3/0:1
echo-cancel coverage 24
compand-type a-law
cptone CN
bearer-cap Speech
voice-port 3/1:1
echo-cancel coverage 24
compand-type a-law
cptone CN
bearer-cap Speech
voice-port 3/2:1
echo-cancel coverage 24
compand-type a-law
cptone CN
bearer-cap Speech
voice-port 3/3:1
echo-cancel coverage 24
compand-type a-law
cptone CN
bearer-cap Speech
mgcp profile default
dial-peer cor custom
dial-peer voice 1 pots
preference 1
destination-pattern 111856T
translate-outgoing called 1
direct-inward-dial
port 3/0:1
dial-peer voice 2 pots
preference 2
destination-pattern 111856T
translate-outgoing called 1
direct-inward-dial
port 3/1:1
dial-peer voice 3 pots
preference 3
destination-pattern 111856T
translate-outgoing called 1
direct-inward-dial
port 3/2:1
dial-peer voice 4 pots
preference 4
destination-pattern 111856T
translate-outgoing called 1
direct-inward-dial
port 3/3:1
dial-peer voice 5 pots
preference 1
destination-pattern 112856T
translate-outgoing called 2
direct-inward-dial
port 3/0:1
dial-peer voice 6 pots
preference 2
destination-pattern 112856T
translate-outgoing called 2
direct-inward-dial
port 3/1:1
dial-peer voice 7 pots
preference 3
destination-pattern 112856T
translate-outgoing called 2
direct-inward-dial
port 3/2:1
dial-peer voice 8 pots
preference 4
destination-pattern 112856T
translate-outgoing called 2
direct-inward-dial
port 3/3:1
dial-peer voice 9 pots
preference 1
destination-pattern 113856T
translate-outgoing called 3
direct-inward-dial
port 3/0:1
dial-peer voice 10 pots
preference 2
destination-pattern 113856T
translate-outgoing called 3
direct-inward-dial
port 3/1:1
dial-peer voice 11 pots
preference 3
destination-pattern 113856T
translate-outgoing called 3
direct-inward-dial
port 3/2:1
dial-peer voice 12 pots
preference 4
destination-pattern 113856T
translate-outgoing called 3
direct-inward-dial
port 3/3:1
dial-peer voice 5555 pots
dial-peer voice 333 voip
destination-pattern 111856T
fax rate 14400
fax protocol t38 ls-redundancy 0 hs-redundancy 0
gateway
line con 0
line aux 0
line vty 0 1
exec-timeout 20 0
password xxxx
logging synchronous
line vty 2 4
exec-timeout 20 0
password xxx
line vty xxx
exec-timeout 2 0
password xxxxxx
line 1/00 1/59
no flush-at-activation
modem InOut
line 2/00 2/59
no flush-at-activation
modem InOut
scheduler allocate 10000 400
ntp clock-period 17179604
ntp update-calendar
ntp server 192.16.202.3
ntp server 134.222.86.7 prefer
end
Rushabh

How to force digital input sample rate?

Does anyone know how to force a Digital Input sample rate and/or tell Core Audio which conversion clock to use... internal or external? Apparently both things can be done from Pro Tools, but I don't have it. My problem is locking onto an A/D converter's 48K Toslink output. I can set 48K in 'Audio - Midi' setup and the audio is perfect, but a few seconds later Core Audio returns to the default 44.1K. I need to force it to stay at 48K, or clock on the signal rather than internal clock.

Braver,
Let me clarify a few things. First, the 6733 supports correlated digital I/O. This means that the digital operation does not have its own clock. You can correlate the digital operation with the AO clock, which will allow a digital operation up to the max AO rate. You can generate a pulse train with an onboard counter and use that as your digital clock source. Also, you can use a completely external clock source to achieve the max digital rate of 10MHz. The knowledge base, linked below, points you to a couple of examples that ship with LabVIEW. Be sure and read the documentation associated with each example.
Knowlege Base
As for
the example CDI Single Point clocked by Counter (E).vi, notice how the output of...

How to bind complex input/output types in web service data control

Hi,
I have created data control using external web service for simple input & output data type and its working fine.
But I don't know how it can be done for complex data types.
My external Web services have complex input & output types. Such as java object which contains another java object again it contains another java object or arry or java collection etc.
Each my service has one complex input data type and for this no user input is require so how I can do it without using any component for it.
I want to bind my page components with this input & output type.
What is the best approach to do this and how to bind screen component.
Regards,
Devang

Hi,
Thanks frank.
I already check this link before posting this so if you have any other link then kindly reply.
Regards,
Devang

How to Immediately Change Counter Output Rate?

I have a piece of code that largely works like this example: http://zone.ni.com/devzone/cda/epd/p/id/5493
In other words, I set up the Counter Output with some initial frequency and duty cycle, but then during the main loop of my program I continuously change the frequency to a new value based on other criteria.
I'm using an M-series PXI card and LabVIEW RT.
The problem I'm having is that the card waits for the next edge before changing the counter output rate. For instance, lets say it is going at a low frequency and I am upping to a high frequency. If the command arrives in the middle of the current pulse, it will wait to complete the low-rate pulse before starting the high frequency output. Is there a way to make it interrupt the current count and immediately start counting at the new rate?
Thanks,
Isaac

Hi Isaac,
I posted the code in LV 8.2 so you should be able to open it now (it sometimes takes several minutes to upload).
There are a few limitations to using the digital lines instead of the counters:
1. The digital lines are updated off of a sample clock which will be much slower than a timebase. For example, on the 6221 the maximum update rate is 1 MHz, while the counter output has a max timebase of 80 MHz. As a result, the number of frequencies you can generate are going to be more restricted (divide down from 1 MHz vs. 80 MHz).
2. On M series devices, the digital lines must be clocked from an external source. This could be generated from a counter
3. You have to build the digital waveform, which is a bit tricky (I think the example code should help out with that but I haven't had time to thoroughly test it).
4. If you are generating digital lines at fast rates, you will need to write quite a few samples at a time to the output buffer to ensure the data does not underflow. If the buffer includes multiple periods of the digital signal, you would have the case that using the counter output would still update more immediately.
Again, to determine the best course of action it would be useful to know what frequencies you want to generate and which exact hardware you are using. I just mentioned the digital lines as an alternative to the counters, but it might not be ideal for your situation.
-John
John Passiak

How to address digital input & output, analogue input & output when communicate with mitsubishi fx1n plc

dear all,
i am new to labview, how to code or address digital input & output, analogue input & output when communicate with mitsubishi fx1n plc or crouzet plc.
pls help.
HM

http://search.mywebsearch.com/mywebsearch/redirect.jhtml?searchfor=mitsubishi+fx1n&cb=ZO&p2=%5EZO%5E...
Try the above link. I know it is a screen-full, but is a search result for Matrikon. They have a whole slew of OPC servers/clients you can try out. Personally, I would go with their OPC server for the Mitsubishi, and use Labview Datasockets. That would be the simplest with the lowest learning curve.
Otherwise, if you wish to use Modbus, you would have to get the commands/syntax from Mitsubishi; might be in their user manual, but I wouldn't lay bets on it. With the Matrikon stuff, the syntax is all built in.
Good luck which ever way you decide to go.
Dave

How to check users inputs

hi,there
i am developing an on-line shop,at the end of checking out process , the users are supposed to submit a details form which including first name ,surname, address,email, phone no, card number etc. Can any one tell me how to check those details are valid before sending to database by using javabean or taglib.
any information is helpful , thanks in advance.

You have three choices:
(1) Client-side checking using JavaScript,
(2) Server-side checking using JavaBeans,
(3) Both.
You can check on the client side using JavaScript to make sure that e-mail address formats are valid, numbers are numbers, strings are the right length and format, dates are correct for the locale, etc. You might want to look at the JSTL I18N capabilities here to make sure your pages can handle different locales. This saves you a network roundtrip if something is formatted incorrectly.
The server-side checking is different: it makes sure that the input satisfies business rules. You can check for correct format again if you wish, OR assume that the client has already taken care of this. (Depends on how paranoid you want to be.) The business rules for correctness belong on the server side, not in the client.
I'd recommend both. They really are two different kinds of checks.
MOD

How to check date input.

In a JText, I input a date valu, when i got the value ,i want to check if it's reasonable.
but idon't know how to check a number:
for example:
i input 31/31/2004,
you know it's not reasonable.
how to check it?

Here is a function that check for a valid date:
public boolean validDate(String strDatum)
boolean dane = true;
Calendar calendarDatum = Calendar.getInstance();
int godina = 0, mesec = 0, den = 0, najgolemDen = 0;
int i;
if(strDatum.length()<10)
dane = false;
else
for(i=0;i<2;i++)
if(!Character.isDigit(strDatum.charAt(i)))
dane = false;
for(i=3;i<5;i++)
if(!Character.isDigit(strDatum.charAt(i)))
dane = false;
for(i=6;i<10;i++)
if(!Character.isDigit(strDatum.charAt(i)))
dane = false;
if(dane)
godina = Integer.parseInt(strDatum.substring(6,10));
mesec = Integer.parseInt(strDatum.substring(3,5));
den = Integer.parseInt(strDatum.substring(0,2));
if(mesec>12||mesec<1)
dane = false;
else
calendarDatum.set(godina,mesec-1,1);
najgolemDen = calendarDatum.getActualMaximum(Calendar.DAY_OF_MONTH);
if(den>najgolemDen)
dane = false;
}//if(dane)
}//else (ako dolzinata e 10)
return dane;
}

Help,how to check a input type?

Dear all experts,
in the selection-screen,user need to key in the vendor consignment code ( vdrcsg for mslb-lifnr ) some user key in storage location ( mseg-lgort ) in this field. Is there anyway tat i can do verification before procees to the start-of-selection? how to check if the user key in correct data type to the selection screen? thanks

hi Joan,
Check these links :
http://help.sap.com/saphelp_erp2005vp/helpdata/en/79/34a234d9b511d1950e0000e8353423/frameset.htm
http://www.erpgenie.com/abap/selection_screens.htm
http://www.sapdevelopment.co.uk/reporting/selscr/selscr_loopscreen.htm
priyanka.

[SOLVED] how to check current colorscheme in vimrc?

I am trying to write a function in vimrc that behaves differently based on colorscheme but I can't work out how to test the value of :colorscheme in vimrc. I'm trying to do this:
if (&colorscheme == 'myscheme')
...something...
else
...something else...
endif
But colorscheme is isn't a variable so the usual way of checking &variable doesn't work. Thanks for heping...
Last edited by starfry (2013-01-19 20:12:21)

Thank you Vain, that is the answer I was looking for. "color[scheme]" does indeed output the name of the current color scheme but I cound not get it to work in the conditional. Using the g:colors_name variable works a treat. Very much appreciated

How many number of input/output arguments allowed in Stored procedure

Please let me know how may input and output arguments are allowed in Oracle stored procedure.
I wan't to writer one generic SP and for that I need to know the limitation on the number of arguments. I am using Oracle 8.0.5.

The output from the BPEL process will be in XML format.
Your requirement is not clear, please state it properly what are you trying to do.
-Yatan

How to check current package/software versions?

How do I check the current versions of packages or software? For example which version of apache or svn I have installed.
Thanks.
-z

Most software that's installed via Apple's installer stores a receipt in /Library/Receipts
You can look at the /Contents/version.plist file within the .pkg to see the version number associated with the package.
This doesn't always cut it, though - for example Apache (as well as several other server components) may get updated as part of a security update so you won't see an 'apache.pkg' in /Library/Receipts
In this case, though, it's probably easier to ask Apache directly...
$ httpd -v
Server version: Apache/2.2.13 (Unix)
Server built: Oct 16 2009 02:12:22
Most services support some kind of command-line switch (typically -v or -V) that gives you version information.

How to check current Autoconfig version

How can we check Autoconfig current version/Rollup level

What patch should i apply to make the Autoconfig as latest?
The latest AutoConfig patch is "Patch 5985992 - TXK AUTOCONFIG ROLLUP PATCH Q (JUL/AUG 2007)" which is also included in "Patch 5903765 - Applications Technology 11i.ATG_PF.H.delta.6"
Is autonfig patch cumulative ?Yes.

How to check current input/output rate on router subintenterface via SNMP?

Similar Messages

Maybe you are looking for