How to configure 2 WAP4410n as AP + Repeater

Hi Everyone
I have a problem. We bought 2 WAP4410n-G5 AP for our customer. I'm trying to configure this two AP as:
1- AP as Acces Point (i have tickled the wireless signal can be repeated by repeter)
2- AP as WDS Repeater (i've chosen the AP MAC adress from site survey)
All of them has the same configuration (SSID, password etc). They are in the same network (10.10.10.0). When we are using only first one everything is OK. But i thing there is a problem with the second one. If you are connected by wire to the same network you can open configuration sites from the first and second AP. So those two AP are seeing each other. But when you are nearby the repeater (with laptop) you can connect to the network but you cannot gain IP adress from DHCP. We were trying to configure WEP, WPA, WPA2 TKIP, AES and without any security but there is still a problem. The firmware is the newest from cisco site on both AP (2.0.1.0). And it's not the first couple of AP from Cisco for small business with the same problem. Please help me guys.
And sorry for my bad English.

Hey team,
Just in case ... here is the link to the user guides:
http://www.cisco.com/en/US/products/ps10047/prod_maintenance_guides_list.html
You can open the link and search for repeater. The section relevant starts on the doc page 49.
Do please let us know how you make out. HTH and kindest regards,
Andrew Lissitz

Similar Messages

How to configure Email output in SD

Dear friends Pls sent me details of how to configure email output in SD module.
<REMOVED>
Thanks & Regards,
<REMOVED>

Hi
Idoc Def :Standard SAP format for electronic data interchange between systems (Intermediate Document). Different message types (such as delivery confirmations or purchase orders) normally represent different specific formats, the IDoc types. However, multiple message types with related content can be assigned to one IDoc type: For example, the IDoc type ORDERS01 transfers the "logical" message types ORDERS (purchase order) and ORDRSP (order confirmation).
Idocs are of two types basic type and the extension type .we need to configure the system settings for this process .
IDOC (Intermediate Document) - A data holder.
IDOC is divided in to three parts.
Control Record
Data Record
Status Record
Control record (Table: EDIDC):
- Every IDOC has only one Control Record
- Each Control Record contains header information like:
o IDOC Number
o Direction of IDOC: Inbound or Outbound
o Date and Time of creation of IDOC
o Date and time when the IDOC was last modified.
o Message Type of IDOC
o IDOC type and extension of IDOC
o Sender and Receiver Partner
Data record (Table: EDID4):
- Data Record contains Data to be processed.
- Every IDOC has one data record with multiple segments in hierarchy.
- Segments and Hierarchy of Segments are defined by IDOC Type and Extension.
- IDOC created has to strictly follow the hierarchy; else IDOC fails with Syntax error.
- Segments which are repetitive have qualifiers attached to it
Status record (Table: EDIDS):
- Status Record describes the status of IDOC.
- Each IDOC contains one status Record with multiple status information.
- Status at each level is appended to IDOC. E.g. When IDOC is created in SAP, Status is This IDoc has been generated through a test transaction, When the IDOC is added to system it is IDOC added, IDOC ready to be transferred to Application
- Status should always be read bottom-up. Status at the top is the latest status.
- Some Example of Status Records:
o Inbound:
§ 53 - IDOC successfully posted
§ 51 IDOC Failed
§ 64 - IDOC ready to be transferred to Application
o
Outbound:
§ 30 IDOC ready for Dispatch
§ 03 IDOC passed to port OK
§ 12 IDOC Dispatched
§ 16 Functional Acknowledgement Positive
§ 17 functional Acknowledgement Negative
IDoc Type: Defines the segments and hierarchy of segments
o Transaction Code:
§ WE30 To create, change or display the IDOC type and the extension.
§ WE31 To create the Segment
- IDOC type defines the segments to be used in the IDOC.
- It also defines the hierarchy and syntax of the segments.
- IDOC extension is nothing but to add segments to standard IDOC types.
- Transaction WE31 allows you to create segments.
- Program RSEIDOC3 documents the use of each IDOC type.
Segments:
Attributes of a Segment:
- Mandatory Segment: If checked, this segment should always exist in the IDOC.
- Minimum Number:
- Maximum Number: Maximum number of times this segment can be repeated in IDOC. -
Parent Segment: Parent of this segment
- Hierarchy level: Level of hierarchy.
Segment Definition (WE31):
Messsage Type: Defines the type of data in the IDOC
o Transaction Code:
§ WE81 To create, change or display the Message type and the extension.
§ WE82 Using this transaction you can link Message Type, IDOC Type, IDOC Extension and version.
- Message type identifies the type of data IDOC holds. E.g. Orders (ORDERS), Delivery (DESADV), Invoice (INVOICE). It also defines what needs to be done with the data in the IDOC, in case of Inbound IDOC, and which data to be extracted in case of Outbound IDOC.
- Message Type is linked to a process code, which in turn is linked to a Function Module. This function module extracts from or posts data to SAP depending on direction of IDOC.
- Relation between Message Type, IDOC type and IDOC extension needs to define. Without this relation Message type or IDOC type cannot be used.
Message Type Create, Change or Display (WE81):
Setup link between Message Type, IDOC Type, IDOC Extension and Version (WE82)
Process Code: Function Module is linked to a process code. This function module in executed for inbound or outbound IDOC.
o Transaction Codes:
§ WE41 Outbound Process Code
§ WE42 Inbound Process Code
- Process codes are linked to a Function Module.
- Relationship is Message Type is linked to a Process Code which is linked to a Function Module.
- In case if you are using a stand alone code to trigger an IDOC, you need not define a process code.
RFC Destination: System definition of destination.
o Transaction Code: SM59
- RFC destination identifies the destination of IDOC.
- In case of ALE:
o In ALE the communication mode is IDOC to IDOC, hence the type used is R/3 Connections.
o It is the destination SAP system which will receive the IDOC.
o In RFC destination you define the destination SAP system details like System, Login and Password.
Go thr below links:
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCMIDALEIO/BCMIDALEIO.pdf
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCMIDALEPRO/BCMIDALEPRO.pdf
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/CABFAALEQS/CABFAALEQS.pdf
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCSRVEDISC/CAEDISCAP_STC.pdf
Sail

How to configure for the price master of the configurable item

in my client we have the configurable items like car doors with different colour as per the color
the price is changing
so how to configure this masterdata for pricing for all the material

Hi
This kindly of process is done at Variant configuration. so the pricing will define in condition type VA00. and the variant process as follows:
Eg: Ford car.If a sale order is raised for fiesta lxi model the system should choose red colour & for vxi blue colour respectively.
ie you need to define the characteristic and assign the values .
This characteristic need to assigned to class.
class need to be assigned to material master
1. T.code : CT04(characteristic) FORD_MODEL, Choose single value & entry required tab & give the input as 01 - fiesta_lxi & 02 - fiesta_vxi.( characteristic values)
2.Tcode: CT04, FORD_BODY( another characteristic)
Choose single value , don't click entry required.
01 - Red( characteristic values)
02- Blue
3. Create class T.code : CL02
fiesta_class
type : 300
4. OBJECT DEPENDENCY:
T.CODE : CT04
FORD_MODEL
CLICK VALUES TAB,
IN FIESTA_LXI CLICK THE 'O' meant for Obj dependency, action & extra.
Edit the dependecy,
010 $Self.ford_body = '01'. & save
Repeat the same for FIEST_VXI & instead of '01' give '02' for blue colour.
, then create a ROH as ford_body. & a KMAT material for the car. .
Then create a Super BOM with usage 3 & give component as ford_body
Then use T.code cu41 (Create config profile)
enter a profile name & class 300 & choose class assignment, choose fiest_class ,
Use T.code cu50 to check the values.
Then create a sale order.
Reward if it helps
Regards
Prasanna R

How to Configure PeopleTools 8.49 Report Manager ?

Folks,
Hello. I am using PeopleTools 8.49. I run a process in Process Scheduler successfully but cannot see its output report. It seems that there is a procedure to configure Report Manager at first so that all reports are stored in Report Manager after run processes in Process Scheduler.
Do any folks understand how to configure PeopleTools 8.49 Report Manager properly ?
Thanks.

Report Manager is a utility in PeopleSoft to view Reports from a different place than Process Monitor. Navigation: Reporting Tools -> Report Manager. It has fours pages: List, Explorer, Administration and Archives.
PSDSTSRV generates a message after a process gets posted in process monitor in order to display reports in Report Manager - List and Explorer page. Hence Integration Broker setup needs to be done and PUB/SUB App Server Processes required to be up and running. Here are the configuration steps:
- Navigate to PeopleTools -> Integration Broker -> Integration Setup -> Service Operations
- IB needs to be configured for four services
•PSRF_FOLDER_CREATE
•PSRF_REPORT_CREATE
•PSRF_REPORT_DATE_CHANGE
•PSRF_REPORT_DELETE
- Open Service Operation PSRF_FOLDER_CREATE and make it active in General tab.
- In Handlers tab add a handler and make it Active. Handler name might differ from the screenshots's name but the Application Class definitons must match. Package name is same as the service operation name.
- In Routings tab, add a routing definition and make it active. Not sure, but I think only one routing definition must be active at a time... Sender and Receiver node are the local nodes - in my case it is PSFT_HR... to confirm your local node, go to PeopleTools -> Integration Broker -> Integration Setup -> Nodes and search for node...
- Repeat the above activity for rest of the services PSRF_REPORT_CREATE, PSRF_REPORT_DATE_CHANGE, and PSRF_REPORT_DELETE also. Configuration is almost similar e.g., make the service active in general tab, Add a new handler and make it active (class id would differ for all) in handler tab, Add a new Routing Name and make it active in Routings tab.
You might want to navigate PeopleTools -> Integration Broker -> Integration Setup -> Routings / Services to check your routings or Services definition and status.
Here completes IB configuration from PIA. A prior understanding of IB setup would help troubleshooting or any kind of configuraiton understanding in case something looks missing here.
Next step is to start the PUB/SUB App Server Processes... Once these server processes are up and running, reports would get displayed in Report manager - List/Explorer page.
Of course, basic IB setup is pre-requisite for the above activity to work. This includes Gateway configuration (PeopleTools -> Integration Broker -> Configuration -> Gateway), Gateway Setup Properties (PeopleTools -> Integration Broker -> Configuration -> Gateway -> Gateway Setup Properties), Quick Configuration (PeopleTools -> Integration Broker -> Configuration -> Quick Configuration) where you need to Gateway URLs and IB domains are active.
let me know i f u have any questions or concerns... they are all delivered nodes by peoplesoft.
Thanks!!....

How to configure oracle listener profile for multiple oracle database

Hi,
I am going to install solution manager system in the same server of ERP EHP4 on Windows. Both DB are oracle.
I'd like to know how to configure listener in this kind of envirnmonent.
a. use two listener and different ports
b. use same listener but different ports
c. use same listener and same port
Which is the correct mothed?
And, after installation, there seem three set of profiles of listten, one for ERP, one for SLM, and the other for OS?(%windir%system32), which one is functional?
Please advise.
Thanks a lot.
Regards,
Alex

Hi,
standard installation is creating new configs for listener for each instance.
I would recommend to use one listener per each instance.
YOU CAN NOT HAVE one port number for two differnet systems!
If you want to use one listener than you must adapt tnsnames.ora, listener.ora and ensure that both systems will use different port numbers.
For example PORT= 15<system number>
Peter

How to configure one TREX host with multiple index servers ?

Hi All,
Does anyone know how to configure TREX on the one host,
with multiple index servers ?
Reason for this is to make better use of resources available on the host server(4 Gig, 4 Processor, Windows2003), to improve the search performance of
our KM content for portal users.
I am using TREX 7 and have not been able to do this,
despite reading the Single and Distributed install
documentation.
Any help would be appreciated.
Regards,
Andres

Hi Andres,
To make use of the RAM a Server provides you have to run two indexserver processes (each can then consume 2 GB);
Proceed like this:
1. Go to TREXdeamon.ini; check if section [indexserver2] is there (it is already provided, but not active in standard installation)
2. In TREXdeamon.ini go to
[daemon]
references sections below
programs=nameserver,preprocessor1,indexserver1,queueserver,alertserver
and add indexserver2 here. Restart TREX; second porcess is then started; can be checked in TREX monitor in Portal as well
3. To distribute existing indexes to the new process, start TREXadmintool and go to Index: Landscape
Go to the last two columns and move the indexes (move master here/secondary mouse click)
If you don't distribute the indexes the new index server process will be regarded when an new index is created.
Hope this helps!
cheers
Bettina

How to configure request manager service for multiple website in one web application

I have set up sp 2013 as below:
web application : wa1
site collection : sc1
sp site: site1, site2
I used 2 WFE, 1 APP, how can I use request manager service to control site1 to wfe1, site2 to wfe2?
Awen

That's not what i'd describe as load balancing.
A better description would be load-isolation. In your description then if the load on site1 was large (and growing) but site2 was quiet then site1 would struggle and eventually become unable to handle the number of users but site2 would still be ok. That's
fine from a QOS point of view but it's not the norm for load balancing. It would work in simple scenarios but the out of the box load balancing tools are much better suited than that sort of approach.
This article shows how to configure the RMS and may help show how your request is difficult to configure:
http://www.harbar.net/articles/sp2013rm2.aspx

How to configure 3 different members under a single Month column

Hi SAP Gurus,
My client requirement is to show the report in following format, where under a Month column 3 different columns having
1) Quantity (Number of unit ) of a product,
2) its rate (Amount per unit), and
3) Total (amount)    will appear in a single report.
   I have Month as a Time Dim, while Qty, Rate and Total are members of account dim.
Que: How to configure such scenario in a single report?
Jan.2011
Product Category:            Qty (Input)   Rate (Input)   Total (Output)
Product 1
Product 2
Product 3
Product 4
Group1
     Where: Total = Qty X Rate
Thanks and Regards,
SouarbhD

Hi,
Use an EVDRE to create your input schedule. You need to have one row with products and 2 columns with time and account. Choose the memberset options as per the requirement. For the accounts, is total calculated with a dimension formula? If yes, then you just need to enter the values for quantity and rate and send the data. The total will be calculated by the system and will be displayed automatically.
Hope this helps.

How can I set an event to repeat on a week day rather than a numerical day of each month?

How can I set an event to repeat on a week day rather than a numerical day of each month? I see an option at the bottom of the repeat window .... but I cannot use it. Actually, when I try it freezes up my Calendar.
Lorrene Baum Davis

These scrrenshots are from Snow Leopard - I would think that Lion wouldn't be too much different.

How to configure an Alert message if communicationChannel(JMS) stops

All,
Is there a way how to configure an alert when the communication channel stops.
<b>Scenario:</b>
In the path Runtime workbench->Component Monitoring->Adapter Engine->Communication Channel monitoring, if we see that a communication channel has stopped(RED traffic light as Status), then can we trigger an alert notification for same.
Currently we have alrerts configured for any message/s failure in the JMS Adapter Framework. So can we trigger simmilar alerts when a comm channel stops(for whatever reason).
Thanks in advance
RK

Hi Sreeram,
Thanks for the quick reply.
We have a scenario where we activate individual channels at a given time. So in this case, Adapter will always be in RED as all queues are never running in our scenario.
So we need an ALERT to be triggered for individual comm channels. Is theer any way that you can think of ?
Thanks and regards
RK

How to configure multiple IP addresses on one NIC?

Hi,
I just installed a OVM Server in version 3.2.1 and the according VMManager. Now i wanted to try to configure the Server/Server Pool. Now i come across a problem, which was already a big problem in OVM 2 while configuring the Networks.
All our OVM Servers have three NICs in them. One is for VMs and Management, the others are for connection to our SAN (Dell PowerVault MD 3220i). My problem is, that due to the network setup, the two NICs for storage need two IP addresses in two different networks each. This shouldn't be a problem, because usually in linux all you have to do is configure something like eth1:1. I remember having huge trouble configuring it in our OVM 2 cluster up to the point where I had to write a shell script to configure the second IP.
Anyways, I have configured two of the storage networks on eth1 and eth2 of the VM Server. Now i cannot configure any more IP addresses, because eth1 and eth2 are not available anymore for configuration in a third network. I really hoped that it would be possible in OVM 3 to configure multiple IP addresses. And probably it is only my lack of knowledge of how to configure it.
So any advice is well appreciated.
Thanks!
Regards,
Marek Hubatka

You should be able to do this by using "VLAN Groups".
http://docs.oracle.com/cd/E35328_01/E35332/E35332.pdf
Check out the VLAN groups section. You must great the VLAN groups before you can assign them to interfaces.

IAS 10.1.2-how to configure different oc4j listen to different virtualhost?

Hi
I have requirement,
we have oracle portal based web site that can be used by outside users over the internet.
And then we have are deploying few new apps/webservices/ear files on a oc4j called core_ws. These web services should not be accessed outside.
I have created a virtaul host in apache on a different port(7799) which was not exposed to public world.
But, how to configure core_ws to inform Apache to listen on only port 7799 but not on port 80?
I tried a diffent route to attack the problem(as mentioned below) which managmenet did not like:
created location directive, worked in dev but not in production as there ISA sitting front of apache.
We could apply filter on the URLs of these web services in ISA but my director did not like the idea as each time there is additional web service we have mess with it.
So, he prefers running these web services on a different port that will not have access to public.
Appreciate your help if have acheived the same earlier.

By your description, it sounds like you want to do what is in this My Oracle Support document:
How To Create Virtual Host Specific OC4J Applications (Doc ID 389819.1)
https://support.oracle.com/CSP/main/article?cmd=show&type=NOT&id=389819.1
(requires login)
You said you were using 10.1.2, so that will work, its a method of creating separate virtualhosts and using rewrites to direct to error pages if an incorrect request is made. For 10.1.3, but there is a dynamic method which is a better approach.
...Ken

How to configure sync with my local ftp server?

I have used XMarks since now because it hallow me to synchronize my bookmarks with my local server. Now XMarks don't work anymore because it's not more possible to synchronize the passwords.
Any other alternative imposes to use an external server and I don't want to use an external server. My data must remain on my machine it's absolutely excluded that i use an external unknown server for this.
The only solution must be a free solution (a real free solution) and the firefox synchronization seems to me the best/only one.
But I've not found how to configure it to use my own server.
So how to do it, where are the options to the synchronizer to give my own ftp server or whatever other server it needs?

iAS 6.0 sp4 officially does only support iPlanet Directory Server 5.0 sp1 and 4.13.
For more details visit: http://docs.iplanet.com/docs/manuals/ias/60/sp4/ig/prep.htm#42084
I guess, you can specify the directory server during the time of installation.
Thanks,
Rakesh.

ASA 5505 8.4. How to configure the switch to the backup channel to the primary with a delay (ex., 5 min) using the SLA?

I have ASA 5505 8.4. How to configure the switch to the backup channel to the primary with a delay (for example 5 min.) using the SLA monitor?
Or as something else to implement it?
My configuration for SLA monitor:
sla monitor 123
type echo protocol ipIcmpEcho IP_GATEWAY_MAIN interface outside_cifra
num-packets 3
timeout 3000
frequency 10
sla monitor schedule 123 life forever start-time now
track 1 rtr 123 reachability

Hey cadet alain,
thank you for your answer :-)
I have deleted all such attempts not working, so a packet-trace will be not very useful conent...
Here is the LogLine when i try to browse port 80 from outside (80.xxx.xxx.180:80) without VPN connection:
3
Nov 21 2011
18:29:56
77.xxx.xxx.99
59068
80.xxx.xxx.180
80
TCP access denied by ACL from 77.xxx.xxx.99/59068 to outside:80.xxx.xxx.180/80
The attached file is only the show running-config
Now i can with my AnyConnect Clients, too, but after connection is up, my vpnclients can't surf the web any longer because anyconnect serves as default route on 0.0.0.0 ... that's bad, too
Actually the AnyConnect and Nat/ACL Problem are my last two open Problems until i setup the second ASA on the right ;-)
Regards.
Chris

I want to set up the Time Machine and I would love to use the Time Capsule but since I already have a wireless router I need suggestions on what other external disks Apple could recommend to use with the Time Machine and how to configure that disk

I want to set up the Time Machine and I would love to use the Time
Capsule but since I already have a wireless router I need suggestions on
what other
external disks Apple could recommend to use with the Time Machine and
how to configure that disk.
A complication that I need to resolve is the fact that I am using Vmware
Fusion to be able to use Windows on my Mac. Now it seems that Time
Machine is not backing up my files
on that virtual Windows without additional configuration and my question
is whether you can advise me here or whether this is only a matter for
the Fusion virtual machine.

If you want to use Time Capsule you can.. you simply bridge it and plug it into the existing router.. wireless can be either turned off or used to reinforce the existing wireless.. eg use 5ghz in the TC which is much faster than your 2.4ghz.
You can also use a NAS.. many brands available but the top brands are synology, qnap and netgear readynas series. These will all do Time Machine backups although how well always depends on Apple sticking to a standard. There are cheaper ones.. I bought a single disk zyxel which was rebadged and sold through my local supermarket. It actually works very well for TM at least on Snow Leopard. Major changes were made in Lion and again ML so do not instantly think it will work on later versions. I haven't tried it yet with those versions.
Any external drive can be plugged into the mac. Use the one with the fastest connection or cheapest price according to your budget. USB2 drives are cheap and plentiful. But no where near as fast as USB3 or FW800. So just pick whichever suits the ports on your Mac. Interesting Apple finally moved to USB3 on their latest computers.
TM should exclude the VM partition file.. it is useless backing it up from Mac OS side.. and will slow TM as it needs to backup that partition everyday for no purpose.. TM cannot see the files inside it to backup just the changes.
You need to backup windows from windows. Use MSbackup to external drive.. if you have pro or ultimate versions you can backup to network drive. But MSbackup is a dog.. at least until the latest version it cannot restore the partition without first loading windows. There are about a zillion backup software versions for windows.. look up reviews and buy one which works for you. I use a free one Macrium Reflect which does full disk backups and is easy to restore.. to do incremental backups though you have to pay for it.

How to configure 2 WAP4410n as AP + Repeater

Similar Messages

Maybe you are looking for