How to configure AP Express to function as only an access point.

I have AP Extreme Base station as my wireless router. I'd like to use my AP Express as only an access point for a secondary printer. I don't want to have the AP Express also serving as a range extender since it compromises my internet upload/downloads speeds. Can it be done?

I don't know
من جهاز الـ iPad الخاص بي
في ٢٥/٠٩/٢٠١٤، الساعة ١٢:٤٦ ص، كتب Apple Support Communities Updates <[email protected]>:
New discussion activity
Bob Timmons has posted in the AirPort community.
How to configure AP Express to function as only an access point.
Nice work. "Join" is what you want.
To post a reply, go to the discussion in Apple Support Communities.
You are receiving this email from Apple Support Communities. You can change your email preferences in your Apple Support Communities Profile.
TM and copyright © 2014 Apple Inc. 1 Infinite Loop, MS 96-DM. Cupertino, CA 95014.
All Rights Reserved | Privacy Policy | Terms of Use | Apple Support

Similar Messages

HT4262 How to configure Airport Express (first generation) from Mountain Lion 10.8?

In OS X 10.8 / Mountain Lion, when I open the Airport Utility (version 6.1) and attempt to configure my first generation Airport Express (b/g), the Airport Utility displays the error "This version of Airport Express cannot be configured with this version of Airport Utility. Download Airport Utility version 5.6." However, I cannot locate a download location for Airport Utility 5.6 which works on Mountain Lion (there is a version which works on Leopard and Snow Leopard).
Does this mean I can no longer configure my access point?
Or am I just overlooking the download location for Airport Utility 5.6 for Mountain Lion / 10.8?
Thanks!
/eh

See this thread for more info:
https://discussions.apple.com/message/19299375#19299375
The pertinent info is as follows:
The 2nd Generation Express was introduced mid-June this year, so if you purchased your Express before that time, you either have a 1st Generation Express, or an even older model that did not use the "Generation" nomenclature.
Please check the label on the side of the Express and look for the Model No.
If you have the "old" version, you will see Model No A1084 or A1088.
If you have the 1st Generation Express, the Model No will be A1264.
If you do have the older version of the Express, unfortunately Apple will not allow you to install AirPort Utility 5.6 on your Mountain Lion machine. In other words, the "older" versions of the Express are no longer supported in Mountain Lion.
There are some "unofficial" or "unsupported" ways to do this....with no guarantees....so I am not sure whether you want to contact Apple Support or an Apple Store to see if Apple plans to introduce AirPort Utility 5.6 for Mountain Lion, or whether you want to try an unsupported procedure to see if it might work.

How to configure users for internal mail routing only in exchange 2013

Hi Guys!
I have a scenario here that i have three (3) group of users, one group is able to have an inbound and outbound mail, meaning they can send and recieved emails from internal and external.The second group of users should have inbound mail(local mail) only
(cannot send and recieved mails from internet), and the third (3) user is they can recieved an outbound mail but they are not allowed to send mail directly to the client,(Ex.
[email protected],[email protected],[email protected]) instead they will use the
[email protected] as the reply to the client. Please let me know how to configure group user 2 and 3.
Thank you.
regards,
Paul

Hi Paul,
Great advice from Maganti, just elaborating steps:
Prevent Group 2 send e-mail to internet by transport rule:
1. Login EAC with administrator, Mail Flow---> Rule, click “Create a new rule, then give a name “Group2 - No Internet Mail”.
2. Conditions: select "From a member of a distribution list" & select group "Group2"
3. Select another condition "Sent to users inside or outside the organization" & Select Outside.
4. Actions: select "send bounce message to sender with enhanced status code" & write your custom message like “You are not authorized to send mails to internet”.
Prevent Group 3 directly send e-mail to internet, however it can send message as group:
We also can create a transport rule which is same with Group2, then open Active Directory Users and Computers to add send as permission with another group (contain same users as group3).
Best Regards,
Allen Wang

How to configure users for internal mail routing only

Hi Guys!
I have a scenario here that i have three (3) group of users, one group is able to have an inbound and outbound mail, meaning they can send and recieved emails from internal and external.The second group of users should have inbound mail(local mail) only (cannot send and recieved mails from internet), and the third (3) user is they can recieved an outbound mail but they are not allowed to send mail directly to the client,(Ex. [email protected],[email protected],[email protected]) instead they will use the [email protected] as the reply to the client. Please let me know how to configure group user 2 and 3.
Thank you.
regards,
LRMCP

Hi LRMCP,
Procedure is perfect which is given by Benoit, just elaborating steps.
Prevent form Sending Mails:
Create a transport rule on Hub Transport Server:
Organization Configuration -> Hub Transport -> Transport Rules -> New Transport Rule -> Give Name “Group2 - No Internet Mail”
Conditions: select "From a member of a distribution list" & select group "Group2"
Select another condition "Sent to users inside or outside the organization" & Select Outside.
Actions: select "send bounce message to sender with enhanced status code" & write your custom message like “You are not authorized to send mails to internet”
Prevent from Receiving Mails:
New User: You can select “require that senders are authenticated” while creating new users which will stop receiving mails from internet.
User -> properties -> Mail Flow Settings -> Message Delivery Restrictions -> Properties -> set Sender Authentication.
For Existing Users:
You have already a group named "Group2" so set sender authentication for all members with this single command.
Get-DistributionGroup "Group2" | Set-Mailbox -RequireSenderAuthenticationEnabled $true
Same procedure mentioned for group2 can be followed for Group3 to prevent from sending mails.
Amit Tank || MVP - Exchange || MCITP - Exchange 2007 || http://ExchangeShare.WordPress.com

How to use Home Hub 3 as a 2nd router(access point...

Hi guys hope you can help; I am trying to add my Home Hub 3 as a 2nd router (ie an access point) to my home network and struggling.
What am I trying to achieve.
I have a fully functioning home network which is working great but the wireless range does not extend to the room above my garage, some distance away from the main house. I currently service it with an Ethernet link from my E4200 router, via the mains wiring, to link to a PS3 there. But I want to extend this to have a wireless network in the remote room so I can link multiple devices - rather than spend more money, deploying a 2nd router which I already have is preferable.
What have I got.
I have a Linksys E4200 router (nice piece of kit) attached to my ADSL line via a Belkin N1 wireless modem-router set to “modem only” mode (I was using a DSL modem until yesterday but that went AWOL and digging out the Belkin router I saw that it had a modem only function – and it/they worked first time )
All of my gear in the house is attached wirelessly to the E4200 which is delivering circa 11.5mbps from a maximum of 12.5mbps for the line measured by BT onsite. So all is fine there.
What have I done to try and use the HH3
Linked an Ethernet cable between one of the Ethernet ports on the E4200 to a mains plug.
Linked an Ethernet cable from a mains plug to one of the Ethernet ports on the HH3 router.
Ie as the PS3 was linked.
3. Switched on the HH3 router: the power light is solid blue, the wireless light is solid blue, the broadband light is off
4. Connected my laptop to the HH3 network and loading up a web page on IE9 displays a web page from bthomehub.home/etc etc with title BT Home Hub and a message “Can’t connect to Broadband”. It is the start of a self- diagnostic routine. Answering all the questions I eventually get a Home Hub Administrative Home Page displayed.
Is there a quicker way of getting to this admin page??
5. I switched off DHCP
I changed the IP address from 192.168.1.254 to 192.168.1.200 as this seems to be what the other threads on this subject did.
When I went to apply the change a message came up telling me that I might not be able to access the HH3. I ploughed on disregarding this and needless to say I could not then access the HH3 via the web interface and trying to access a web site nothing happened.
6. I did a hardware reset on the HH3
7. Going through the motions again, when I got to the admin pages again, I switched off DHCP and this time left the IP address alone, ie 192.168.1.254.
When I went to apply this I got the message
“After changing these settings you will need to renew the IP address of all devices connecting to your BT Home Hub. Please follow the instructions provided with your devices.”
I applied the change – but have not yet done any fooling around with IP addresses on my laptop because I don’t want to start mucking around with my laptop
I then tried to access a website, and failed, but on this occasion rather than nothing happening, the Home Hub website came up again displaying the error message page.
And that is where I stand. All looks so easy when reading other threads on this and other forums but it is not working for me.
Any help greatly appreciated.
The IP settings on the E4200 are
IP 192.168.1.1
Range 192.168.1.100 to 192.168.1.149
Also connection type on the E4200 is POE not POA – as far as I recall that is what it needed to be to connect to the DSL modem and work.

Thanks for the speedy reply!
I have actually came across this page before - I seem to hit a snag when I connect the repeater hub (my HH3). As outlined, I have at all times kept the repeater hub connected via ehternet into one of the regular LAN ports to my main HH5.
But when I connect my laptop to the repeat hub (HH3), I am actually connected to the internet somehow (I assuem using the HH5 network) but under my network connections it says I am connected to the HH3. As a result, when I go to the homehub settings page 192.168.1.254, it brings me to the main HH5 settings page and not the repeater HH3.
According to the instructions it says I should "Ignore the not connected page", but I am connected and I cant seem to alter any of the settings on my HH3 while it is connected to the HH5.
Any other pointers?
Thanks!

How do I find the MAC address of a CLIENT ACCESS POINT created from the FILE SERVICES ROLE

I have several Client Access Points created within the clustered File Services Role. The only way I seem to be able to determine the MAC address of each of these, is by visiting the DHCP server.
Does anyone know if there is a way of reporting on this from the server (active node) itself? I have tried ipconfig all, checked the properties of the CAP in the FCS console etc.
Many thanks.
Kathleen Hayhurst Senior IT Support Analyst

Hi,
As far as I know there have no original option for query all the CAP MAC address, may you can create a PowerShell command then filter the configuration result, you can ask
in PowerShell forum for the further help.
More information:
PowerShell forum:
http://social.technet.microsoft.com/Forums/en-US/bf0e249b-a9f3-4bef-a536-c210b3f09340/powershell-script-to-alert-on-failed-system-state-backups?forum=winserverpowershell
The related KB:
Failover Clusters Cmdlets in Windows PowerShell
http://technet.microsoft.com/en-us/library/hh847239.aspx
The related article:
PowerShell for Failover Clustering: Frequently Asked Questions & Enabling CSV
http://blogs.msdn.com/b/clustering/archive/2009/05/23/9636665.aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

How can i change regulatory domain C to A of access point

Recently my office got an access point - (AIR-CAP2602E-C-K9) which is not synchronizing with controller (AIR-CT2504-5-K9 )as it is in domain A , all other AP also in domain A. Now can i change the domain of access point or what is the possible solution to add new AP with controller ? is it possible to run both domain (A, C) at the same time with one controller ?

Migrating Access Points from the -J Regulatory Domain to the -U Regulatory Domain
The Japanese government has changed its 5-GHz radio spectrum regulations. These regulations allow a field upgrade of 802.11a 5-GHz radios. Japan allows three frequency sets:
•J52 = 34 (5170 MHz), 38 (5190 MHz), 42 (5210 MHz), 46 (5230 MHz)
•W52 = 36 (5180 MHz), 40 (5200 MHz), 44 (5220 MHz), 48 (5240 MHz)
•W53 = 52 (5260 MHz), 56 (5280 MHz), 60 (5300 MHz), 64 (5320 MHz)
Cisco has organized these frequency sets into the following regulatory domains:
•-J regulatory domain = J52
•-P regulatory domain = W52 + W53
•-U regulatory domain = W52
Regulatory domains are used by Cisco to organize the legal frequencies of the world into logical groups. For example, most of the European countries are included in the -E regulatory domain. Cisco access points are configured for a specific regulatory domain at the factory and, with the exception of this migration process, never change. The regulatory domain is assigned per radio, so an access point's 802.11a and 802.11b/g radios may be assigned to different domains.
For more information please refer to the link-
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/321930RN.html#wp111182

How to configure Airport Express N router and Netgear G router with Extreme

I have a primary Netgear G router (WRT54G) connected to my cable modem box. I have an Airport Express N router streaming music in another room and also extending the wireless network.
I am planning to demote the Netgear router as a switch + wireless network extender connected to my home theater setup (dish+apple tv+ps3) and purchase a new dual band Airport Extreme connected to the cable box and acting as the main router.
My question is if its possible for the N devices to still use N network while the G devices not demoting the whole wireless network to G? That's the reason why I want the Extreme. If yes, how to go about doing it? If not, I will just buy a cheap switch and use that for the Home theater and leave the current setup alone. Anyone who has a similar network, please advice. Thanks!

My question is if its possible for the N devices to still use N network while the G devices not demoting the whole wireless network to G?
Yes. To do so, you would need to connect the Netgear to the new 802.11n AirPort Extreme Base Station (AEBSn) by Ethernet, and then, reconfigure it as a bridge (disable both its NAT & DHCP functions).
In this configuration, the AEBSn & AXn can provide the 802.11n network and the Netgear can provide the 802.11g network.

How to configure Goto context menu function on the web?

We are running a web template on IE browser. After the report run successfully, left click on any key figure column, we can see Goto context menu, from here, we can go to detailed report (e.g. from the current Cube level to more detailed ODS level). However we find this jump from cube level to ODS level (Goto context manu) works on our QA system other than DEV system.
These stuff were configured by SAP consultants who left our company one year ago, if anyone knows how to make the Goto context menu works by drilling down from cube level to ODS level, please let us know and we are really appreciated!

dear Bhanu,
We figured out the problem, it is because we click Goto then select "Display Documents" which yields a 400 error, then go back to click Goto, pick up the target link we want and it yield the error. After we hit F5 to reload the URL link, then directly select Goto our target, then it works fine!
But one more question, under Goto context menu, we find four menu context items:
1. Display Documents
2. Documents for Navigation Status
3. Our application target1
4. Our application target2
Select option 1 yields an error like mentioned above.
Select option 2 pops up a new window with Key Figure selection box and a button called "Additional Functions", but seems go nowhere.
Option 3 is setup in our system by using RSBBS like you suggested.
Option 4 is not in RSBBS.
Then our questions are for option 1, 2, and 4. What are the functionalities of option 1 and 2, are these two standard web functionalities of BW web reports? and these two options always show up on the web no matter whether they work or not, right? We are confused with option 4, it's not listed in RSBBS, then how come it show up?

How to configure Airport Express to Extend Wireless Network

I have an Airport Extreme (AE1) as my wireless router, with two other Airport Extremes (AE2 and AE3) connected to it via ethernet and operating in bridge mode. Together they cover the first floor of my house with wifi, but I want to use an Airport Express (AX1) situated on the second floor to connect wirelessly to AE2 and extend my wifi network to the second floor of my house.
Nothing I have tried has allowed AX1 to extend my wireless network. I'm using the latest Airport utility in Mavericks, and AX1 is the old plug-in type but it's the newer "n" version that is still configurable by Airport Utility. Any suggestions would be appreciated.

I almost ALWAYS recommend against wirelessly extending your network. Obviously, I'm unfamiliar with your layout but 3 extremes on the same floor seems like overkill, too, but could make sense depending upon contruction and usage.
In any event -
Adding Wi-Fi base stations when it is unnecessary can reduce Wi-Fi throughput because the Wi-Fi network will require more data management overhead. The network configuration also becomes more complex. In the case of a wirelessly extended network, throughput may be reduced to less than 60 percent of that of a single device.
Risk free test - run some speedtests in the corners then remove an extreme and re-run the tests. Then, buy one of the new tower 'AC' extremes and set it up as your single router and test again. I call this risk free since you have 14 days to return the new 'tower' extreme if you don't want to keep it but its range is THAT much better than the prior gen. You could make this cheaper by buying it from the Apple refurbished store and selling your older extremes.

How to configure AirPort Express 802.11n (1st generation) in OS X 10.7.5

I have an old Airport axpress and cannot configure it anymore since I updated to OSX 10.7.5.
Can somebody explain how I can fix this?
Greets

Contact the softwareproducer.
That would be Apple.
If you are sure that you have downloaded the correct version of AirPort Utility 5.6 for Mac OS X Lion and you continue to see this error message, you will likely need to re-install the Lion operating system on your Mac.
Contact Apple Support first, before you attempt this.
http://www.apple.com/support/contact/

Hard to accept that (2) airport extremes, (3) airport expresses, cannot be configured to play pandora from iPad to one access point to play to all devices simultaneously.

I have a verizon router hooked to my AP Extreme For my home wireless network. I have mutiple airport express along with an Apple TV wirelessly connected to the network also. With all the ways that these can be configured, how is there not a way to have all of the AP Express receive the same Pandora stream at the same time? Can they all be named the same thing so that my iPad thinks it's sending the signal to only one unit? Again, I find it insanely difficult to wrap my head around the fact that this is so difficult to make happen with the Apple technology available today. Any suggestions???

Yes iTunes can according to this Apple information page: AirPort Express frequently asked questions (FAQ) - Apple Support
Can iTunes send a single AirPlay stream to multiple AirPort Express stations?
Yes. You can send an AirPlay stream to multiple remote AirPort Express units . The maximum number of remote AirPort Express units is up to six. The actual number that will work in your environment will depend on conditions such as building composition and radio interference, distance to the remote AirPort Express units, and available network capacity relative to your other usage.
I don't know enough about Pandora to help you in-depth with that - maybe someone else here can - but you should first test if it works with iTunes.
That way you'll know if your network setup is working like you intend to. From there we can troubleshoot Pandora,

How to configure to run SNP that creates only PReq and Stock Transfer only?

Hi all,
I am very new to SCM.
Please help me on the scenario like this:
-There are 3 Distribution Centers (DC): 2400, 2500, 3800 and a Vendor: 1003.
-Each DC can take products from otherDC. But only DC 2400 can directly send purchase requisition to Vendor 1003 when no stock at all DCs.
-There is a Forecast released from Demand Planning to SNP, that is 1000 products at Distribution Center 2400.
-I will run SNP Heuristic (or Capabable to Match or Optimization) to cover this demand.
-Usually, SNP can create: Purchase Requisition, Stock transfer Requistion, and Planned Order.
                     But I only want the SNP to create Purchase Requisition and Stock Stransfer only.
The question are:
1.In which situations (tock situation,u2026) the system can create Requisition and Stock Stransfer only ?
2.I need create a new Supply Chain Model (Model) and a new Planning Version from scratch. How can I configure the system (Transportation lanes, Product Master Data, Procurement type in product masteru2026) and make it run to satisfy this scenario?
3.Do I need setting differently for each SNP method ( Heuristic, Capable to Match, Optimization)?
Thanks very much for your support.
XuanDuyen

Dear Mr. Aparna,
Thanks for your quick reply.
Now I haved created a model like the scenario with product T-F204 and can run. ( I do not use vendor 1003. I created the Plant 1000 instead). But as you said, when I run with SNP Heuristic method (Network level), the system alert:
u201C Error exist in Locationsu2019 processing sequence for product T-F204u201D
However, I search internet and found a book about CTM. It also discuss about this and the solution as below:
u201CRecursive Replenishment
When using complex supply chains, with many locations and various directional
supply routes, it can be easy to confuse a level-by-level planning tool. In certain
situations, recursive planning can occur. Recursiveness, is when the planning
algorithm is thrown into a loop (circular replenishment). Location 1000 can ship
to location 2400, and location 2400 can ship to location 1000. Situations such as
this can cause the CTM engine to terminate since it cannot find a starting point.
 The solution: Reduce to number of muximum consecutive transport order chains.
Within the CTMProfile, Settingsu2192Master Data Settings tab, planners can control
the sources of supply for External Procurement. With the parameter Maximum
Number of Consecutive Stock Transfers, you determine how many consecutive
stock transfers CTM planning can create. This value does not restrict the total
number of stock transfers for a demand. If you enter a value here, you can prevent
the system from transporting the receipts for a demand over several locations due
to the procurement priority. Also, you must have modeled the master data in such
a way that a direct stock transfer is possible if the system ignores the procurement
priority. If a direct stock transfer is not possible, CTM cannot fulfill the demand.u201D
Currently, our system runs only with Heuristic. It could not run CTM and Optimization so I could not check.
My questions are:
1.     Is the solution of the book can apply for my bi-direction transportation lanes requirement?
2.     If it is true, with my scenario, what is the best u201CMaximum Number of Consecutive Stock Transfersu201D I can set?
3.     How can I model u201Cthe master data in such a way that a direct stock transfer is possible if the system ignores the procurement priorityu201D?
Please follow the link to download the book (and view page 107 of book (page 117 of Acrobat Reader) as bellow if you want:
http://www.mediafire.com/?9clag9op3lm0iv9
Thanks very much for your help!
Xuanduyen

How to configure RDS to let a specific RDS group access a specific RDS server (no VDI or farm) ?

Hi there,
We have one domain with 40 sites. On each site is a RODC, wich also has RDS. (RDS the old way, no broker installed)
The RODC's are 2008R2 and 2012R2 servers.
Everything works fine, however everyone can access all servers as a straight forward RDS user (no VDI).
Everyone is in the build in group for remote user.
I'd like to have people that work on ServerA only are able to contact serverA for RDS.
B on B, C on C and so on ... This for all 40 sites.
I made a policy for each site allowing RDS_A to access server A and so on. Is this the right way to do it, or can I do it having less GPO's ? I need 40 right now!!! Linking the policy to the right OU, containing the specific server.
Something is still wrong, because other people still can access serverA.
I get into it, but maybe I'm doing it wrong, so please give me some advice :)
Thanks,
Ben.
Ben van der Meer

Hi Ben,
Thank you for posting in Windows Server Forum.
You can achieve this through group policy but you can do one thing. You can create one group for one server (Suppose group A for server A, B for B, so on). After creating that group add particular user to that group and apply the group policy setting on that
group for particular group.
The group policy which can apply is “Allow users to connect remotely using Remote Desktop Services” under below mention path.
Computer Configuration\Policies\Administrative Templates\Windows Components\Remote Desktop Services\Remote Desktop Session Host\Connections
More information.
http://technet.microsoft.com/en-us/library/ee791922(v=ws.10).aspx
Hope it helps!
Thanks.
Dharmesh Solanki
TechNet Community Support

How to configure LabVIEW web server to allow viewing and accessing the content of a folders

I have added the following html line to the body of the html file generated by the LabVIEW Web Publishing Tool:
<a href="MyFolder" target="_blank">My Folder Content</a>
I expect the link labeled "My Folder Content" to open a new browser window displaying the content of "Myfolder" which is located inside the LabVIEW webserver root folder. I got an error instead. If I substitute "Myfolder" with a filename, the browser will display the file just fine.
Can someone provide me with some hints on configuring the web server for this purpose?

Hola Hector
Estoy trabajando con tu caso y se me ha hecho bastante interesante.
Solo te quiero preguntar... que version de Internet Explorer tienes?
Utilizas algun otro web server ? ( Mozilla tiene este problema me parece)
Segui los pasos que mencionas con Internet Explorer 6
y pude abrir la carpeta sin problemas.
Te pido por favor que me contestes estos datos para darte una solucion muy especifica.
lamentablemente tengas que hacer referencia directa ( todo el path) a los archivos del folder para accesar a ellos si tu explorador no lo permite.
Lo unico que puedo confirmarte es que parece no ser un problema de National Instruments.
sin embargo si me das mas informacion podemos descartar cualquiera de las conclusiones a las que he llegado.
Espero tu respuesta
Saludos
Erwin Franz R.

How to configure AP Express to function as only an access point.

Similar Messages

Maybe you are looking for