How to create sine wave?

How do you create a simple sine wave in Logic, and how do you change the frequency?
Logic noob deluxe

Try the Bitcrusher plugin.
But, dude, I get the feeling that to indulge yourself in your noob-ism will wear very thin very quick, and if your next question is where the Bitcrusher is and where you have to click and then how you can use it and what the controls do and after that how you can record what it does, then it might happen that noone will bother to read anymore let alone reply.
We can hold your hand only so far and ultimately you must decide on your own where to click, what to try and when to think.
How about getting some 1:1 tuition to get you up and running ? It's infinitely easier for one person sitting next to you than for a bunch of folks scattered allover the globe which try to read your mind.
Christian

Similar Messages

  • How to create sine wave and step input using cwgraph in VB 6.0

    hello..
    i'm doing my master's project now. i'm stuck on how to create a sine wave and a step input using the cwgraph using VB 6.0. please help. thanks.

    hello..thank for the reply.
    i'm having problem with my coding using cwgraph. can anyone help. everytime i do the full compile, there's error.but it can still can run, but can't convert to application form.for your info, i'm using RTscope and cwgraph to plot graph.the error is in the cwgraph coding.below are part of the coding with error. and can somebody tell me how to add cwgraph component in the VB? i try adding component, but it's not in the list of component,and i've browse for it already too.i'm doing the software at home, but i'can run it at my lab cause cwgraph component is not listed.please help.
    Dim countTime As Integer, count1 As Integer, countFreq As Integer, countVolt As Integer
    Private Sub cmdRun_Click()
    If cmdRun.CausesValidation = True Then
    cmdPause.CausesValidation = False
    tmrOsc2.Enabled = True
    tmrOsc3.Enabled = True
    Else
    cmdPause.CausesValidation = False
    tmrOsc2.Enabled = False
    tmrOsc3.Enabled = False
    For count1 = 0 To 100
    Data1(count1) = 0
    Data2(count1) = 0
    RT1.Value(1, count1) = 0
    RT1.Value(2, count1) = 0
    RT1.Refresh
    CWGraph2.Plots(1).PlotY count1 ' THIS CODING HAS AN ERROR ...
    CWGraph2.Plots(2).PlotY count1 ' THIS CODING HAS AN ERROR ...
    Next count1
    End If
    End Sub

  • How to create a wav file from 24bit 96Khz sampling rate data

    Hi
    I am trying to make an VI which will play sound while acquiring data from PXI 4472 DAQ card.
    My sampling rate is 96Khz and PXI 4472 card is a 24bit card.
    Wave files are in 8 or 16 bit and the sampling rate is 8000, 11025, 22050 and 44100. How will I be able to play the data which I am acquiring.
    How would i normalize the data into the required format needed for most of the sound cards to play.
    Or are there any codec available in Windows XP which i call to play a 96KHz 24 bit sample
    Does anybody ever encountered this type of problem.
    Thanks in advance
    Nitin

    Whilst the 'standard' RIFF format specification usually accomodates 16 bit data, there is of course no reason that you can not create your own extension. It just won't be playable by Media player using the 'standard' installed drivers or codec. This may not be a problem....
    WAV files can and do support other formats, you just need to know how to handle them......
    There is howerver a 4GB limit (related to the pointer size in the WAV specification) which with higher bit depths on the sampling does start to become a bit of a problem.
    To give you a few samples of other types of wav files check out the following site here
    http://www-mmsp.ece.mcgill.ca/Documents/AudioFormats/WAVE/Samples.html
    The following definitions for WAV audio formats may also be of interest here
    http://www-mmsp.ece.mcgill.ca/Documents/AudioFormats/WAVE/WAVE.html
    Good luck with 24 bits.

  • How to create a .wav file in visual basic?

    I'm having the audio sample data(scaled data) in an array created by the CWAI_AcquiredData event. How do i convert this to a .wav file so that i can play back the audio data i acquired.
    Can any one help me out ????????

    Hello
    You should probably check out the MSDN for examples on how to do this.
    I think the Speech 5.1 SDK probably has some function that would help you out.
    Hope this help
    Bilal Durrani
    NI
    Bilal Durrani
    NI

  • How to create a wave-like masking effect?

    If you look at the first 3 seconds of the video:
    http://www.youtube.com/watch?v=xPYWy97pfc0
    the logo is slowly reveal with a wave like masking effect, how do you do that in after effect?

    Use an animaged shape or mask as a track matte for the logo.

  • Play sine wave with soundcard on CVI

    Does anybody know how to generate sine waves with the soundcard ?
    Thank you for your help.

    Diver,
    The way to go here is the Windows SDK. First make sure that you have the Windows SDK installer; go to the help menu and you should be able to select Windows SDK . If you don't have that option then you need to run the installer again and change the installation to include the Windows SDK.
    Once you have this running there are a couple of ways you can do this:
    Play a WAV file: this is the easy and fast way of doing it; record or generate the WAV file with any simple sound editor and use the function PlaySound() from the Windows SDK to play strait from the file (you can find more info about the function in the Windows SKD help file).
    Play generated data using lower level soundcard functions: this is not as easy, but gives
    you the most flexibility; you basically open a session with the sound card and write data to it. I'm attaching a very basic example that can get you started.
    Use Media Player to play a file: you can use ActiveX to embed Media Player in your UI and use it's capabilities to play wav files. CVI has a good shipping example about this, you can find it here.
    You can request this feature for future version of CVI; go to http://www.ni.com/contact and select product feedback to submit your request.
    In the mean time I hope this helps you get started.
    Regards,
    Juan Carlos
    N.I.
    Attachments:
    WaveOut1.c ‏2 KB

  • I would like to create a sine wave in Illustrator. How do I do this in a simple way?

    Hi,
    As the title suggest I would like to create a sine wave in illustrator. I know that applying the zig zag effect to a line and choosing "smooth" will create a cosine wave. But is there a simple way like that to create a sine way? Or any way at all?
    Thanks for the help!
    ekmanch

    1. start with the zig zag effect
    2. with the scissor tool cut where the ends of the red line is - I made the rest blue to make it clear
    3. delete the blue segments to get this
    4. using the black pointer or scale tool stretch horizontally to match the reference
    5. using the white pointer select one of the smooth anchor points, and using the Scale tool and holding Shift drag to scale constraining horizontally until the curve matches the reference
    6. select the other smooth point and with the scale tool selected press the Enter key on your keyboard twice to apply the previous scale
    click the image to see it larger

  • How can i measure only the valley voltages of a sine wave in labview 7 express evaluation version?

    I am trying to convince my company to send me to purchase labview and send me to classes for labview.
    I am trying to put together a small demo for them using the Labview 7 express evaluatin copy that I recieved.
    What I am wondering is how can filter out everything besides the valley peaks on a sine wave.
    What I am trying to accomplish, is create an example showing that Labview can sameple from a sine wave, read about 5 "valley" points of the wave, evaluate these based on a value that i can define, and signal pass or fail.
    attached is a picture of what i have so far
    Ryan
    LV 7.1
    Attachments:
    progress.bmp ‏3841 KB

    Hi,
    I built a VI using LabVIEW 7.0 that detects the valleys in a sine wave. It uses the 'Peak detector' VI that I believe is available in the evaluation version.
    (Functions palette >> All Functions >> Analyze >> Signal Processing >> Time Domain >> Peak Detector)
    I have attached a VI as well as the screen shots its front panel and block diagram.
    I hope this helps.
    Sincerely,
    Feroz
    Attachments:
    valley_detector_bd.jpg ‏36 KB
    valley_detector_fp.jpg ‏72 KB
    valley_detector.vi ‏29 KB

  • How to change the phase by 90 deg of a sine wave

    Hi
    Does any one know how to change the phase of a sine wave by 90 degrees.
    Mal

    Hi Malkoba,
    Thank you for your post.
    Having looked at your VI I can say that you have created the correct inputs to the 'Sine Waveform.vi'.
    However the dial you had created had no affect as it was not wired into it the 'Sine Waveform.vi' on the block diagram.To fix the problem I have wired the 'Phase' dial into the 'phase' terminal of the waveform generator. This now changes the phase of the sine wave during runtime.
    The dial also now has a digital display (numeric box below it)- this can be used to read the dial's value, or feed in specific values into the control.
    Please find a modified version of your VI below.
    Regards,
    Field Sales Engineer | National Instruments | UK & Ireland
    Attachments:
    NI_phase shift sine.vi ‏31 KB

  • Creating and controlling a sine wave

    I am a TA for Control Systems & Instrumentation at Texas State University. As the assistant I am required to assist students in their homeworks and projects. I have encountered a problem in assisting the students. How do I create a Sine Wave wit ha sampling frequency of 200 Hz? Obtain the power spectrum of the signal and change the sine wave frequency to 25 Hz. Determine if the resulting frequency is about the Nyquist frequency. Then increase the sine wave to 125 Hz and compare to the Nyquist frequency again.

    There is an example shipped with LabVIEW 2009 called "Resampling a Waveform (continuous).vi" I think this vi will demonstrate what you are trying to do. Change the sine wave frequency using the frequency control in the Test Signals (A) box and change the sampling frequency by updating the output rate control in the Output timing box. You will then see the original waveform spectrum at the original sampling rate (Fs) and the re-sampled spectrum will be shown in red so you can see the shift.
    Systems Test Engineer
    Certified LabVIEW Architect (CLA)

  • How to dynamically adjust Frequency, Phase and Amplitude for a Generated Sine Wave in C/C++?

    Hi,
    I wonder if anybody know how to dynamically adjust Frequency, Phase and Amplitude for a Generated Sine Wave in C/C++? This is a part of my project: I need to dynamically generate a sine wave voltage signal by some calculation using the data from a simultaneous analog input and another signal.
    Your help will be appreciated so much!
    Marlon

    Hello Marlon,
    Here is an example of changing frequency and ampliude for an E-series device in Labwindows/CVI. The programming should be similar in C for your S-Series device. As is says on the linked webpage above, this process is going to be very processor intensive since you will continually be creating a buffer.
    Nicholas C
    National Instruments
    Applications Engineering

  • Formula node to create a sine wave

    I am trying to create a Sine Wave to display on an XY Graph using a formula node. I've put in my formula which is: Sine=Emax*sin(2*pi*f*t). I am getting a very choppy almost triangular wave displayed on the xy graph. Any suggestions as to how to get it to display a clean waveform.
    Thanks
    Chirs

    Assuming you have more than "LabVIEW base", open your tools palette and have a look at "signal processing...signal generation..sine pattern"
    LabVIEW Champion . Do more with less code and in less time .

  • Creating a Sine Wave Chart with Continue if True

    Hello, 
    I want to create a simple sine wave chart using a while loop and using the continue if true mode. I want to use a Not icon to accomplish this. I also need to have a stop button that a user can press to terminate the process. I have attached my initial sine wave chart using the stop if true and my attempt at accomplising the continue if true. 
    Thanks for any help! 
     

    It sounds like you want the loop to continue if the stop button is NOT pushed.  Does this give you a hint about how to write your program?

  • How to generating three phase sine wave simutiously with Vistual C++?

    Here I want to generate three phase sinewave at the same time with the phase angel 120 continiously. I can creat a task that contain 3 AOs, and generate 3 same sine wave at the same time. But I can not create 3 individual task which contains one AO channel, and write data to FIFO. Please tell me how to realize it?

    Hello, Rilee,
    Thank you very you very much. But I am still confused. The website I can not open. As you said, I shall create a data array to contain three phase data, for example, sinedata[750], sinedata[0:249] contains first AO, and sinedata[250:499] the second, and the rest is the third. then
    1. send the data for sinedata[0] to sinedata[249], to the board. with DAQmxWriteAnalogF64;
    2. send the data for sinedata[250] to sinedata[499], to the board. with DAQmxWriteAnalogF64;
    3. send the data for sinedata[500] to sinedata[749], to the board. with DAQmxWriteAnalogF64;
    and or so.
    Is all the above description right?
    Here I have several questions:
    1. When shall I send second section sample data? I think it shall be all the first data have been written to the board. And How can I know that all the first section data have been sent to the buffer?
    2. If I call DAQmxWriteAnalogF64 to write the second section data to buffer after the have finished first section data written, will this function affects the wave of the first section data?

  • How do I make a sine wave in illustrator?

    Hi,
    I started a thread earlier this evening but I think that I accidentally flagged it as "solved" or something like that (I'm new to this forum). So I'm trying this again. I want to know if there's a way of creating a sine wave in illustrator. I've managed to create a cosine wave by using the zig zag effect on a line and choosing "smooth". But I can't seem to find a good way to make a sine wave.
    This is the difference for anyone wondering:
    I want a sine wave just like the picture above.
    Thanks for the help!
    ekmanch

    ekmanch,
    As I (mis)understand it, to create a single full sine wave, you may:
    1) Create a horizontal line 2.5 times the length of the desired full sine wave (or you may adapt the length later);
    2) Effect>Distort & Transform>Zig Zag with 4 Ridges per segment and Smmoths Points and the desired height as the Size (or you may adapt later);
    3) Object>Expand Appearance;
    4) Object>Path>Add Anchor Points;
    5) With the Scissors Tool cut where the sine wave starts and ends;
    6) Ungroup if needed and delete the end bits (and adapt the length/height if needed).

Maybe you are looking for

  • FRM-40602: Cannot insert into or update data in a view

    Hi all! I have a form based on a view and I want to get rid off this message. I set the properties blocks query only but it still doesn't work. Does someone met with this situation? Many thanks!

  • SMTP server problem for UTL_MAIL ..

    Hi , I asked the Mail server admin and he said that the relaying is set to allow on the settings , the procedure still cant send to outside domains : SQL> alter system set SMTP_OUT_SERVER ='oursmtp'; SQL>CREATE OR REPLACE PROCEDURE send_email AS    B

  • FCP 5.0 crashes when trying to open 4.5 old projects

    I've tried to open numerous older FCP 4.5 projects, they actually start to load and then FCP program shuts down and the screen says " the application Final Cut Pro has unexpectedly quit". Whats happening, please help!!!

  • How to change Data Object

    Hi everyone, I m trying to change from one D.O. to another using the "Global Change Data Object" at BAM Active Studio, but when I find the D.O. wich I want to use the radio button its greyed out. I really need to change the D.O. and I dont see how to

  • How to maintain default values to the screen fields.

    hi, i m creating screen in se51. when i press New button the screen is filled with default values nrart = 'h' and proz1 = '100' . how can i set default values. plz give me a response