How to get windows 7 on mac

Hello I have bought my Macbook Pro 13" 2 weeks ago how install i windows 7 on it what do i need to install windows 7??

hans_k wrote:
So i need copy disk of windows 7 ISO image
You know where I can get windows 7 ISO Image??
You buy it, try Amazon.

Similar Messages

My mac book air can't start installation, because i use windows installation in DOS to make partion, now no mac os on it. How to get back the mac os? i have a window based iso image from a friend, because in my country there is no Apple service.

my mac book air can't start installation, because i use windows installation in DOS to make partion, now no mac os on it. How to get back the mac os? i have a window based iso image from a friend, because in my country there is no Apple service.

It sounds like you destroyed your boot partition and the recovery partition. Depending on it's age, your MacBook Air might be able to do a net boot. Plug and ethernet connection into it and attempt to boot. If it has the right firmware, it will find a net boot configuration on the net and boot that. Then it will give you a Recovery Partition like display and allow you to reinstall the OS X version that came with it.... assuming that it was Lion or ML. If your computer came with Snow Leopard, then even the net boot won't work.
At that point you need a bootable USB Key, or an external DVD drive AND a Snow Leopard installation DVD.
An Apple Store, if there is one nearby, MAY be able to get you going again. However, whatever is on the SSD now will be toast too.

How to get photos from mac to iPhone 6? when i try it just comes up iCloud instead of my photos

how to get photos from mac to iPhone 6? when i try it just comes up iCloud instead of my photos

Make sure Settings > iCloud > Photos > iCloud Photo Library (Beta) = "Off"
Then sync your iPhone using iTunes and make sure your sync settings for photos are set correctly in iTunes.

How to get Windows Server 2012 trial license key?

How to get Windows Server 2012 trial license key? I'm trying to install WinServer 2012 Trial on a VMWare Workstation 9. I'm asked for the product key during set up. If I ignore putting in the key (since I don't have one) The install fails stating no valid
key. I tried this with Oracle's Virtual Box and the same thing happens. I tried using Majic JellyBean to find the key, but that only works on pre-installed OS. A Technet article said to use aaaa-bbbbb-ccccc-ddddd etc. in the spaces. That doesn't work either.
Articles all over the web seem to have other people in the same boat. Please help :)

Download the trial version from here -
http://www.microsoft.com/en-us/server-cloud/evaluate/trial-software.aspx It does not require a key. If the software is asking for a key, it is not the trial copy. Where did you get your copy?
.:|:.:|:. tim

How to get windows username printed on each page irrespective of application? we have cm6030f.

How to get windows username printed on each page irrespective of application? we have HP CM6030F.

Hi,
Normally, you will receive a Windows Azure Pass from your local Windows Azure team. Please try to contact your local Windows Azure contact (http://support.microsoft.com/gp/customer-service-phone-numbers?wa=wsignin1.0
Also, you could see this page
http://www.windowsazurepass.com/AzureU/AcademicFAQ and apply the free trial azure via (http://www.windowsazurepass.com/AzureU/).
Q: I am a student. Can I apply for a pass?
A: Windows Azure Educator Grants are only for valid faculty. If your faculty has been awarded a Windows Azure Educator Grant, you will be able to get a pass through him/her for you coursework. If you are interested in learning more about Windows Azure,
we encourage you to share these Educator Grants with your faculty or sign up for the FREE 3-month trial offer.
Regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

How to get window system user?

Hi,
How to get window system user use PL/SQL(form develope6i)?

If you don't use Oracle database then you will have to do one of two things:
(1) Now I'm back in the office I can check D2KWUTIL. The version I have comes with Forms6.0, so it is somewhat out of date, but it has a method called WIN_API_ENVIRONMENT.Get_Windows_Username - which works for NT/95 only, although I'm sure a later version will support more recent OS.
(2) If that's no good then you'll have to use whatever facilities your database offers: I only know Oracle.
I also repeat my suggestion that you try the Forms forum for additional help. This is the Database forum and so is focused on serverside Oracle PL/SQL. For your needs the Developer Suite forums are better.
Cheers, APC

How to get appstore for mac os x 10.4.11?

how to get appstore for mac os x 10.4.11?

Go to Apple menu -> About this Mac. If you have a G3, G4, or G5 processor you can't access the App Store at all.
If you have an Intel Mac, updating to 10.6.6 is described here:
https://discussions.apple.com/docs/DOC-2455

DOES ANYONE KNOW HOW TO GET THE DOWNLOAD MAC OSX 10.7.0 BECAUSE NO MATTER HOW MUCH I TRY I CANT FIND IT

DOES ANYONE KNOW HOW TO GET THE DOWNLOAD MAC OSX 10.7.0 BECAUSE NO MATTER HOW MUCH I TRY I CANT FIND IT

AS mentioned, you need 10.6.8 & the App Store first, it's not available any other way, & 10.7 instead of 10.8 requires a call to Apple...
Snow Leopard/10.6.x Requirements...
General requirements
   * Mac computer with an Intel processor
    * 1GB of memory (I say 4GB at least, more if you can afford it)
    * 5GB of available disk space (I say 30GB at least)
    * DVD drive for installation
    * Some features require a compatible Internet service provider; fees may apply.
    * Some features require Apple’s MobileMe service; fees and terms apply.
Which apps work with Mac OS X 10.6?...
http://snowleopard.wikidot.com/
It's been pulled from the online store & Apple Stores, so you have to call Apple to buy it, last I heard.
Buy Snow Leopard > http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard
Call Apple Sales...in the US: 1-800-MY-APPLE. Or Support... 1-800-275-2273
Other countries...
http://support.apple.com/kb/HE57

I need to know how to get my desktop (mac mini) laptop (mac book pro) iPhone4S

I need to know how to get my desktop (mac mini) laptop (mac book pro) iPhone4S & ipad all sharing the same iCloud... I have four deveices... I\iPad & iPhone are synced to the mini, but the laptop is the main one.

First, your Macs must have OS X Lion, and your devices iOS 5. Then, go to your devices and open Settings > iCloud to configure the same Apple ID. In your computers, go to System Preferences > iCloud and set up iCloud with the Apple ID

HDD failure, I'd like to know how to get Windows 7 back on it.

Hello everyone, I've had a HDD issue lately, but before I move on to describe my issue, here are the specs of my notebook:
HP Pavilion dv6-3264ca
AMD Triple-Core CPU 2.2 Ghz
6GB RAM
128MB ATI Graphic Card
750GB Toshiba HDD
Windows 7 64-bit
The issue:
Recently I've had a very unfortunate HDD failure. The recovery partition wouldn't even load. I tried booting my notebook on Linux with the HDD still attached, and it wouldn't read. I extracted the HDD and placed it in an HDD-enclosuer and it still wouldn't load on Windows XP or Vista or 7. It would however read in the device manager of Windows and also in the BIOS.
I needed to extract some high-priority data from there so I managed to retrieve all my data safely through a data recovery service, but now the drive is rendered useless. I was told a low-level format might be able to help it be usable again, and if that were to happen, the recovery partition would then be removed in the process.
In addition to that, I would like to install Windows 7 64-bit onto the drive, but the notebook box did not come with an installation CD, which is quite frustrating. Is there any way HP can let me download Windows 7 through some warranty service?
I have a one-year warranty on my laptop.
So in closing, I would like to know if I can get Windows 7 back onto my HDD for free, or if I need to go about buying Windows 7 again.
Any advice from you kind folks?
This question was solved.
View Solution.

Hi,
Here are Two options.
1. If you have ( or can borrow ) a retail Windows 7 installation disc that is exactly the same version as your OEM installation - ie if your notebook came with Windows 7 Home Premium 64bit this is the exact retail version you would need.
If you don't have access to a retail disc, you can create an installation disc yourself - just download the correct Disc Image from the link below and use an application such as ImgBurn to burn the ISO correctly to a blank DVD.
http://www.mydigitallife.info/download-windows-7-iso-official-32-bit-and-64-bit-direct-download-link...
Use the disc to perform the installation, enter the Windows activation key found on the underside of your notebook when requested and when the installation has completed, use the 'Phone Method' detailed in the link below to activate the OS - this method supported by Microsoft and is popular with people who just want a clean installation of Windows 7 without the additional software load normally bundled with OEM installations.
http://www.kodyaz.com/articles/how-to-activate-windows-7-by-phone.aspx
Any additional drivers you may need can be found Here.
2. You can order a replacement set of Recovery Discs using the link below - these cost around $30 if you live in the US.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00810334&cc=us&lc=en&dlc=en
If you have any problem with this link, order them directly from HP.
If you live in the US, contact HP Here.
If you are in another part of the world, start Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

How to install Windows on MAC? (Can't see the check box "Install or remove Windows 7 or later version" on Boot Camp Assistant)

I want to install Windows 7 on my MBP mid 2012 but in Boot Camp does not appear the check box: "Install or remove Windows 7 or later version". I continued with making the USB bootable with Windows 7 but then when I restart and boot with the USB I still can't install Windows because then I receive an error: ""Windows cannot be installed on this disk. The selected disk is of GPT partition style."
From OS with Boot Camp I didn't manage to make a partition for Windows instead I made one with Disk Utility (formated FAT).
After booting from USB that partition was also formated into NTFS necessary for Windows. Still the same error.
Any idea how to install Windows on my MAC?

My Windows copy is a X64.
MBP mid 2012 with Mountain Lion 10.8.3.
Model Identifier:          MacBookPro9,2
Processor Name:          Intel Core i5
Processor Speed:          2.5 GHz
Number of Processors:          1
Total Number of Cores:          2
L2 Cache (per Core):          256 KB
L3 Cache:          3 MB
Memory:          4 GB
Boot ROM Version:          MBP91.00D3.B08
SMC Version (system):          2.2f41
Should have:
MacBook Pro (13-inch, Mid 2012)
MacBookPro9,2
MBP91.00D3.B08 (EFI 2.9)
If you are refering to this I tried to update the EFI version (I see only SMC version 2.9 as a diferrence of what I have) but on installing I received an error: "This software is not supported on your system."

How to get Outlook 2011 Mac emails in Mac Mail Lion version

how do I get Outlook 2011 Mac eml files to Mac MAIL for lion?

I'm not aware of an easy convertor from Outlook 2011 to Mac mail, but if you have still have access to the e-mail account setup in Outlook, I'd just setup Apple Mail to download the mail from that account. Then Mail will pick them up next time you get mail.
However if you don't have access to that account any longer or it's POP3 account, that won't work.
In which case you need to drag each mailbox folder (In-Box, Sent, etc.etc.) whilst in Outlook to a folder on you Mac (Desktop is fine), then from Apple Mail, goto Import Mail Mailboxes, choose Files in mbox format and select all your .mbox files, these will then apear in a folder called Import.

How to get windows form object of a MMC snapin node using MMC automation object model

Hello,
I am using automation object model for an existing mmc file and just trying to traverse all nodes of it. And i am able to do so.
My query is : how can i get the access of windows form object of a particular node . Windows form is present in result pane of a node, i want to get access of that so that i can perform some automation on that form.
http://msdn.microsoft.com/en-us/library/aa815049(v=vs.85).aspx
I found that if OCX control is in result view of any node, then "view object -> control object property" returns
the automation interface supplied by the control in the result view.
However, if result view is HTML view then how to get the automation interface of that result
view.
Thanks in advance,
Sumit

Hi Sumit,
I read the link you provide above. It seems that when you want to achieve your target by using MMC automation
object model, you need to use codes. Based on the programming language, if use VB, I suggest you post the question in
VB Forum. If you want to use C#, may post in
C# Forum.
In addition, there is an answered question, may help you to find the correct forum.
MMC development forum?
http://social.microsoft.com/Forums/en-US/3796a8e9-674e-4da0-a40e-4e4b69575c8e/mmc-development-forum?forum=whatforum
Since, it’s more related to development. We may can’t provide some more detailed information. Thanks for your
understanding.
Hope this helps.
Best regards,
Justin Gu

How to get windows username & password

Hi friends,
Requirement is to get windows username & password,
My server is Tomcat4.0,
My code in login.jsp page is
<%
String auth = request.getHeader("Authorization");
if (auth == null) {
response.setStatus(response.SC_UNAUTHORIZED);
response.setHeader("WWW-Authenticate", "NTLM");
return;
if (auth.startsWith("NTLM ")) {
byte[] msg = new sun.misc.BASE64Decoder().decodeBuffer(auth.substring(5));
int off = 0, length, offset;
String s;
if (msg[8] == 1) {
off = 18;
byte z = 0;
byte[] msg1 = {(byte)'N', (byte)'T', (byte)'L', (byte)'M', (byte)'S',
(byte)'S', (byte)'P', z,
(byte)2, z, z, z, z, z, z, z,
(byte)40, z, z, z, (byte)1, (byte)130, z, z,
z, (byte)2, (byte)2, (byte)2, z, z, z, z, //
z, z, z, z, z, z, z, z};
response.setStatus(response.SC_UNAUTHORIZED);
response.setHeader("WWW-Authenticate", "NTLM "
+ new sun.misc.BASE64Encoder().encodeBuffer(msg1).trim());
return;
else if (msg[8] == 3) {
off = 30;
length = msg[off+17]*256 + msg[off+16];
offset = msg[off+19]*256 + msg[off+18];
s = new String(msg, offset, length);
//out.println(s + " ");--------------------------> here getting system_name
else
return;
length = msg[off+1]*256 + msg[off];
offset = msg[off+3]*256 + msg[off+2];
s = new String(msg, offset, length);
//out.println(s + " ");
length = msg[off+9]*256 + msg[off+8];
offset = msg[off+11]*256 + msg[off+10];
s = new String(msg, offset, length);
out.println("Hello <span style='position:relative; width:190;"
+ " height:10;filter:glow(Color=#009966,Strength=1)'>");
out.println(s + "</SPAN>");----------------------------------->here getting loginname.
%>
from this i was able to get systemname & username,How do i get password.
Is it possible to get password?
Thanks,
Satya.

There's no way to get the password. NTLM uses a two-round challenge-response scheme which never send the password (neither clear nor encrypted) on the wire.
Why do you need the user's password? Is your service going to access a backend service using the user's credential? If so, you may need to use Kerberos delegation.

How to get iTunes and Mac OS 10.5 to leave my file organization alone

I’ve organized my MP3 files for iTunes (using Mac OS 10.5.6) on a MacBook Pro. I did this manually since I have over 600 folders and thousands of song files. iTunes had created a mess. For example some albums were split up into different artists, composers or album names. Some files names began with a space or a dash, so they were our of alphabetical order. There were all kinds of nonsence with duplicated files etc. Once I got things all cleaned up and orderly I tried to make a backup of the master list by copying the files to a peripheral hard drive. The backup folders instantly reverted and even compounded the chaos that I had just fixed! If I delete all files from iTunes and reimport I end up with the same mess. How can I get iTunes and Mac OS 10.5 to leave my organization the way I want it and not revert to the old mess?

I don't understand.
If you uncheck *Copy files to iTunes music folder...* and *Keep iTunes music folder organized*, iTunes will not mess with the files unless you are RIPping them from CD using iTunes.
How do I change the tags so they are organized the way I want.
I don't know how you want them organized.
iTunes uses the tags and puts them into Artist/Album folders based on the ID3 tags.
If you are not using iTunes to organize stuff and simply naming things as you want, tags are irrelevant to how you put the files into folders and what you name the files.
When I copy the master list (with my organization) from one peripheral drive to another the files show up with the old names and folders.
Okay.

How to get windows 7 on mac

Similar Messages

Maybe you are looking for