How to implement a dual booting PXI system using windows 7 and labview RT

Good Day
My name is Mariano Ocana from the University of Manitoba, and I want to implement a dual system using windows 7 and labview RT in a PXIe-1082 chassis with a PXIe-8102 embedded controlled (the chassis came with windows 7 installed). What are the steps to use both systems (windows and RT)  in the same chassis?, in the NI help comes an example implementing a dual system using windows xp and RT, it is the same procedure?.
Thank you in advance for all your help.
Regards
M. Ocana

Greetings, Mariano.
The real issue you have to contend with is whether or not you have a LabVIEW RT license.  If the 8102 controller was purchased Windows-Only, you likely do not have a license to run LabVIEW RT on the controller - you can purchase one, I think it's about $500, and at that point you can request a LabVIEW RT Configuration CD (that's not what it's called, but the sales guy will know what I'm talking about).  The Config CD is a CD that will partition your controller correctly with both FAT32 and NTFS filesystems (in the appropriate way) to allow you to run Windows 7 and LabVIEW Real-Time on the controller correctly.  Once done, you can then switch within the BIOS between LabVIEW Real-Time and Windows in order to dual-boot.  
Either way, you likely need to contact NI sales to either purchase an RT license (if one was not received at the time of purchase) or to request a Configuration CD (it might also be called a dual-boot install CD or similar).
-Danny

Similar Messages

  • How do you increase font size in Bridge using windows 7 and a 4k monitor?  It appears as though this issue has come up previously but there is no answer.

    How do you increase font size in Bridge using windows 7 and a 4k monitor?  It appears as though this issue has come up previously but there is no answer.

    Unfortunately this will require some new programming by Adobe and there's no way to know when that will happen. In the meantime, the only option I think you have available to you is to change your resolution so that your monitor is using fewer pixels per inch.
    Kinda blows the whole value of the newer monitor but I suppose you can switch back and forth from low res when you are working in Bridge to high res when you are working in PS.
    Sorry, but for the time being, that's about it.
    Best,
    Gary

  • How to implement SSO to non-SAP systems using SAP logon ticket?

    Hello,
    We would like to implement Single Sign On between our SAP Netweaver system and a Siebel which is a non-SAP system using SAP logon tickets.
    Can anyone please give me some leads on this, in particular:
    1. Is there a JAVA API or an SAP plug-in that can be implemented on the Siebel machine to extract the SAP logon ticket?
    2. As the other machine might seat on a complete different domain, is it possible to implement SAP logon ticket without using cookies (perhaps through the HTTP header?
    3. In case you think using SAP logon tickets is not the best solution here I would be happy to hear any other suggestions you might have.
    Roy

    Hi,
    I'm currently using SAML as well. Unfortunately the SAP J2EE cannot work as authority (identity provider) but what you can do is using an open implementation of SAML such as opensso which is an open version of SUNs Java System access manager.
    There are a couple of other projects such as opensaml, apache's wss4j or shibboleth that might be interesting in this context.
    I just installed opensso and got it working with SAP J2EE 7.0 using SAPs JAAS SAMLLoginModule to authenticate users within SAP J2EE.
    In this scenario opensso serves as identity provider just as you need! There are a couple of Policy agents available on SUNs Download site you can use with Apache, Tomcat, JBOSS, WebSphere, Bea Web Logic etc. in order to authenticate! Otherwise you just directly authenticate against opensso. When installing opensso you can configure the type of user store you want  to use! By default it uses LDAP but you can also use different types of user store using JDBC or other mechanisms. Since you have a Directory Service you could easily connect it to your existing directory.
    There is also a way to map user ids directly in opensso by adding a uid mapping class. I created some documentation with lots of screenshots about using opensso with SAP J2EE. You can easily use opensso with any other system that supports SAML. In the case of SAP the usage is currently limited to SAML versions 1.0 and 1.1. Version 2.0 is not yet supported but should be in one of the following versions.
    Here are some links you might want to check:
    OpenSAML: https://spaces.internet2.edu/display/OpenSAML/Home
    wss4j: http://ws.apache.org/wss4j/
    shibboleth: http://shibboleth.internet2.edu/
    opensso: https://opensso.dev.java.net/
    On SDN you will find a documentation on how to connect SUN Java System Access Manager to SAP J2EE (see https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/906d9fc6-31b9-2910-1385-90edad7d7570). As I said opensso is based on the SUN Access Manager code and looks quite the same. So you can adapt this documentation in order to configure opensso or you can just ask me for the documentation.
    Hope this is helpful...
    Let me know if you need further assistance on this topic
    Cheers

  • Dual boot ing pre-installed Windows 8 and windows 7?

    Hi there
    I have a lenovo G505s that came with windows 8 and would like to download windows 7 and have them dual boot for gaming purposes so I was wondering I could get any advise on the matter.

    Welcome to the forum!
    With Windows, generally you have to install the older version first then the newer with dual booting.  Since you already have Windows 8 installed that might be a problem.  Also resizing the partitions on your hard drive to make room will disable the option to use One Key Recovery at boot up.  If the machine is still under warranty, you might wait till the warranty expires before re-arranging things.  Also prior to installing Windows 7, make sure there are drivers available for your system's hardware.
    Owner & Operator of the following:
    ● Lenovo Ideapad Z570 w/ Win 7 & Win 8.1 Dual Boot ● Lenovo Yoga 3 Pro w/ Windows 8.1 ● Toshiba A75-S206 w/ Win 7
    ● IBM Thinkpad T-23 w/ Win XP ● IBM Thinkpad T-22 w/ Win XP • As well as multiple desktops dual/triple booting XP, Vista and Win 7.
    ★ Find a post helpful? Thank that member by clicking on the ☆Star☆ to the left awarding them a Kudo.
    ★ Posting a problem and a reply is helpful and it answers your question, please mark it as an "Accepted Solution"
    ★ I'm not a Lenovo employee, just a volunteer geek who likes to help folks. Enjoy your time here, pay it forward by helping others !
    ★ Sorry, I don't answer questions via Private Messages. Posting in the appropriate forum is the best way to get assistance.

  • How to implement singleton service if i m using only jar and war component

    hello,
    in my application i m using only jar and war component .
    as i m not using EAR for deployment so i dont have weblogic-application.xml file.
    so in this case how i implement weblogic singleton service .and how to call active method

    From the documentation:
    After you have created a singleton service class using the SingletonService interface, you must define it as a singleton service within WebLogic Server. This singleton service object contains the following information:
    The path to the class to load as the singleton service.
    The preferred server and other candidate servers for the singleton service.
    The following excerpt from the cluster element of config.xml shows how a singleton service is defined:
    <singleton-service>
    <name>SingletonTestServiceName</name>
    <user-preferred-server>myManaged1</user-preferred-server>
    <class-name>mycompany.myprogram.subpackage.SingletonTestServiceImpl</class-name>
    <cluster>myCluster</cluster>
    </singleton-service>
    Note that the config.xml is located in the <domain-home>/config directory

  • How do i access my email in firefox - using windows live and google

    I want an icon for email as in internet explorer but how do I get it. Currently using windows live mail and gmail

    You have to go to optonline's support site to find out the setting to use for their IMAP account if they allow an IMAP account.

  • How do you do dual boot without Dual activation for CS3?

    I know this has been discussed but I can't find the post called Daryl Pritchard, "Activating CS3 with both Vista and XP Pro on same system" #3, 21 May 2007 12:49 am .  That link seems to be dead.
    I'm slow to make the switch, but I'm planning to install Vista on the same box I've had XP Pro on.  I have a LOT of software on this box (it normally takes 34 hours to install everything from scratch) including VIsual Studio (2003, 2005, 2008), Lotus Notes designer (R6.5, R8), 3D Studio Max, etc. etc. etc.  I'm not ready to flip the switch and just run the Vista upgrade.  I want to dual boot with XP on one partition and Vista on the other, so that I can boot to XP if something doesn't seem to be running correctly under Vista.
    Here is my dilemna.  I also have Photoshop CS3 installed on my laptop, and I need it there because I travel every few weeks and still have to manipulate images.  I'd like to avoid deactivating licenses everytime I get on a plane or drive across town.  I don't want to have to use up both of my "activations" when I'm staying within the intent of the Eula - it's only going to be used on one machine.
    How has everyone else faced this challenge?  I know there are plenty of people with dual boot set ups.
    I'll deactivate Photoshop on XP Pro if I have to, but that's going to be a headache if I have to turn on the laptop everytime I work in XP on the desktop and need to modify a PSD image.  

    I believe you can only deactivate/activate 20 times, precisely to keep
    people from swapping the two licenses amongst more than 2 computers, so
    deactivating on your travel-computer will only work for the next few times
    you do it.
    Depending on what things you do to your images, you might be able to get by
    with using Elements to work with the PSDs.  The newer versions of Elements
    lets you work with Layers so it may be ok.  Install the PSE trial and see
    how well it works.
    If you must have Photoshop, and one copy needs to be on your laptop, then
    you must choose dual-boot you want to use it on, and perhaps install the
    trial on the other bootable partition and if it works fine for everything,
    and at the end of 30-days, choose which one to keep activated, or decide
    that you can upgrade your XP.  I think you should attempt to upgrade it,
    anyway, just to see if it's even possible.   I think you can uninstall the
    upgrade if you do it right away, and get back to your XP...I had to do that
    when my graphics card refused to work, even though the Vista Upgrade Advisor
    didn't complain.  Installing Vista from scratch seemed to work.  I just
    bought a new HD and reinstalled everything.
    Another thing to consider is that Windows 7 will be available for retail
    purchase before Halloween and people like it better than Vista as far as
    running things faster, so maybe just skip Vista.  The only glitch I had was
    having to uninstall Nero's packet-writing (CDRW as a floppy) software after
    I upgraded to Vista and it didn't quite work and I had to use a Nero-clean
    utility to get rid of it.  It isn't compatible with Win7 and I could have
    gotten around the problem by merely uninstalling Nero before upgrading and
    putting it back, afterwards.  I have an older version of Nero was my actual
    problem.
    I am running the Win 7 Ultimate RTM from my MSDN subscription and like it a
    lot...more transparency and they finally combined the quick-links with the
    actual task-bar so you can just pin things down there and they are
    highlighted if they're running or not highlighted if not--sort of like a Mac
    has been doing for a while, but with much smaller icons if you want.

  • Dual boot kali linux with windows 8

    i have ideapad y510p and i want to dual boot kali linux with windows 8 
    i want a full guide to do it please !!help!!!

    Hello,
    if you got problems with the kernel, you can try backbox-linux. The kernel there is newer. It is based on Ubuntu 12.04 LTS.
    Have a nice day
    thoschi
    LENOVO IDEAPAD Z710 59403383,i7-4700MQ,8 GB DDR3-RAM,1.920 x 1.080 Pixel,NVIDIA® GeForce® GT 740M,Hybrid (1 TB S-ATA + 8GB SSD)

  • I'v got the latest macbook pro 13" and it dose not come with the lion os disk so how do i get the boot camp drivers for windows 7 without an os disk

    i'v got the latest macbook pro 13" and it dose not come with the lion os disk so how do i get the boot camp drivers for windows 7 without an os disk

    Page 5, step 2, #2, 2nd bullet.
    http://manuals.info.apple.com/en/Boot_Camp_Install-Setup_10.7.pdf

  • How can i find a boot cam by using internet after windows 7 set up

    how can i find a boot cam by using internet after windows 7 set up.

    how can i find a boot cam by using internet after windows 7 set up.

  • How to generate a chirp(linear FM) signal using dds theory in LabVIEW FPGA.

    how to generate a chirp(linear FM) signal using dds theory in LabVIEW FPGA.
    attachment:a sine signal using dds theory. Hope to get some help. Thanks!
    Attachments:
    FPGA DDS SineGen IP.vi ‏42 KB

    you need to increment the "accumulator increment" during the duration of the chirp.  the "accumulator increment" controls the frequency of the DDS cycle.  by increasing it's value, you are increasing the frequency.  the math for increment values follows the same math as determining the frequency to increment value.
    Stu McFarlane
    Viewpoint Systems, Inc.

  • -- A file association problem exists, which prevents the file you're trying to download from being associated with the correct application by the operating system using window 7  IE 11

    A file association problem exists, which prevents the file you're trying to download from being associated with the correct application by the operating system
    USING WINDOW 7  IE 11  HOW CAN I FIX???

    Try downloading the offline installers:
    Adobe Reader
    Flash Player for Internet Exporer - ActiveX
    Flash Player for Firefox - NPAPI

  • How can I create an csv/excel file using pl/sql and then sending that file

    How can I create an csv/excel file using pl/sql and then sending that file to a clients site using pl/sql?
    I know how to create the csv/excel file but I can't figure out how I would get it to the clients site.

    968776 wrote:
    How can I create an csv/excel file using pl/sql and then sending that file to a clients site using pl/sql?
    I know how to create the csv/excel file but I can't figure out how I would get it to the clients site.You are trying to do it at a wrong place..
    Whay do you want database (pl/sql) code to do these things?
    Anyhow, you may be interested in :
    {message:id=9360007}
    {message:id=9984244}

  • I use Windows Vista and Microsoft Outlook. After migrating to iCloud, the calendar of iCloud tranferred only part of my past Calendar items to the folder iCloud Calendar in my Outlook. How can I transfer all the entries?

    I use Windows Vista and Microsoft Outlook. After migrating to iCloud, the calendar of iCloud tranferred only part of my past Calendar items to the folder iCloud Calendar in my Outlook. How can I transfer all the entries? In iCloud's site all are there.

    If the calendar is on iCoud.com, all you would need to do to get it on your phone is go to Settings>iCloud on your phone, sign into your iCoud account and turn Calendars on.  The iCloud calendars will then download to your phone.

  • We are having old home movies put on DVD's. How do we import them to MacBook Pro using Snow Leopard and iMovie 8.0.6.  Can watch the video, but can't get it to import.

    We are having old home movies put on DVD's. How do we import them to MacBook pro using Snow Leopard and iMovie 8.0.6?  Can watch the movies on the laptop, but they will not import.

    We took 3 video cassette 8mm that were recorded in the early 90's to a place that burned the videos onto 3 DVDs.  When inserted to our Mac, the DVD player comes on to play the DVD. Opened Quicktime, but can find no way to import. Went to File>Open File>Sony_DVD_Recorder_Volume. Clicked on Sony_DVD-Recorder_Volume and it shows a file named VIDEO_TS.  Clicked on that and 6 files showed VIDEO_TS.BUP,   VTS_01-0.BUP,   VTS_01_0.IFO,  VTS-01_1.VOB,   VTS_01_2.VOB, VTS_01_3.VOB.  Where is DVDxDV?

Maybe you are looking for