How to load SW in 1310 wireless bridge when flash has no SW-image
During an upgrade (autonomous software), I indicated that the system should create enough room to load the new software.
However, while loading the new software, the system crashed, so no image at all is left in flash.
How can I load a software image in the wireless bridge ?
In old days with routers this was possible with some x-protocol over the console connection.
Is there any description on how to handle this on a wireless bridge.
I always end up in the boot mode.
Thanks
If the device doesnt have an image, type reset on the boot console, When it comes up , if will ask for certain options
set IP_ADDR
set NETMASK
set DEFAULT_ROUTER
set IP_ADDR
set NETMASK
set DEFAULT_ROUTER
Make sure the value (IP_ADDR, NETMASK .. ) are copied exactly, other wise it will not work, Once you have copied, if you type set, you can seet these values.
After this type the following commands
tftp_init
ether_init
flash_init
and then
tar -xtract tftp:/// flash:
and boot
Thanks
NikhiL
Similar Messages
-
I have a 1310 wireless bridge....when I power it up, it sometimes does not boot up. The I LED will just sit there and blink and the R and E LEDs will blink in unison with it. After a while just the I LED blinks. I cannot find any literature that tells me if this is an error code or not.
Also, when the thing does boot up, it tells me that the Radio interface is down and disabled, when in fact if you go into the settings of the radio interface, it is selected to be enabled.
What might be going on here?
Thank you.No, there is nothing on the console port when the thing is in the condition described above.
If I do get a successful boot, I can then access via a console port. I may try to reinstall firmware and see if that fixes the problem.
So you are saying the radio link will show as disabled/down until it actually tries to associate/authenticate with another bridge unit? That is normal? -
"Restart Now" IOS command for 1310 Wireless Bridge
I have 2 Cisco Aironet 1310 wireless bridges setup, line-of-sight, 3/4 mile apart, one as Root, the other as Non-Root. Occasionally they drop their connection but a hard restart of either or both bridges will reestablish the connection. What is the equivalent IOS command to the
"GUI > System Software > System Configuration > Restart Now" command? I would like to be able to telnet to either/both units and issue/script the appropriate command.the command is "reload"
BRIDGE# reload
Regards
Surendra -
Enable AES encryption on 1310 Wireless bridge
Hi All,
I have requirment to enable the AES encryption on the management VLAN traffic between connected root and non root bridges . can any one share the configuration guidelines please ??
below is the network setup .
Router<---->SW1 ( main office)--> Root-bridge < ---------->non root-bride------SW2 ( remote end site)
Apart from the specific configuration on the wireless bridge is any extra configuration required on the Switch interfaces??
Regards
LernerHello,
1. Make sure you are running version 12.3(7)JA or later since WPA2/AES was not always available for the 1310.
2. How do you currently have the root/non-root configured?
Ideally, adding AES shoudl be fairly straight forward. Keep in mind we recommend using WPA2 with AES.
configured on your root AND non-root:
dot11 ssid
authentication open
authentication key-management wpa version 2
interface do1
encryption mode ciphers aes-ccm -
Power Injector for 1310 wireless bridge
Hello,
We have a failed power injector on a 1310 series bridge. Will the "Power Injector LR" from a 1410 series bridge work on the 1310?
Thank you,
MattNo... both have a different output and should not be used interchangeably.
See this post by Surendra:
https://supportforums.cisco.com/message/3280050#3280050
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
How to load a page or page layout when click on hyperlink using jsf
Hi,
I created a hyperlink using a4j:commandlink, when i click on this link, i have to load a page. How to include the page using, <ui:include>, when i click on the hyperlink.
Please help me in this issueEnclose your <ui:include> component in a <h:panelGrid> or a <f:subView> as said above, and use rendered attribute that is set to false.
When you click on the link, set the rendered attribute of panelGrid or subView to true. Now use reRendered attribute of a4j:commandLink to rerender the panelGrid or subView.
Also check this regarding RoseIndia . -
Hi,
Is there a way to automatically disable the wireless interface when the LAN interface is connected on R61s and X61s?
Thank you!Hi,
Thanks for the answer. I'm trying to deploy the profile that I've created on all my laptops. But i'm facing an issue for a while.
When the profile is deployed on a laptop, Access Connections finds a new ethernet port and asks to assign it a profile. But the problem is that Access Connection don't allow me to assign it to my wired profile, only to my wireless profile and that doesn't make sens to me. Besides, it is written in the dialogue box that ethernet profiles are disable for the match of the new port...
Is there any way to assign the new port to the new profile without human interaction or just how to make the wired profile available when access connection is launched and find a new ethernet connection
Thanks in advance! -
1310 Wireless Bridge Poor performance
Hello I am getting really bad performance on a bridge i am trying to get up,
Laptop - Switch - AIR-BR1310G-E-K9-R attena-ed ----------------
attena-ed AIR-BR1310G-E-K9-R switch laptop.
When doing an FTP Transfer i get a poor 1MB, these are currently in a lab enviroment, this is a far cry from what i am hoping for,
can anyone see an issue
show run
Building configuration...
Current configuration : 1892 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname site1
enable secret 5 $1$XQ0Z$Fzjg/dJ/I1sY5bLjss0l4/
clock summer-time BST recurring last Sun Mar 1:00 last Sun Oct 2:00
ip subnet-zero
ip domain name xxxxxx
ip ssh time-out 60
ip ssh authentication-retries 2
ip ssh version 2
aaa new-model
aaa authentication login xxxxx
aaa session-id common
dot11 ssid XXXXXX
max-associations 1
authentication open
authentication key-management wpa
infrastructure-ssid
wpa-psk ascii xxxxxxxxxxxxxxxxxxx
username Cisco password 7 047802150C2E
username xxxxxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxxx
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
no power client local
power client 50
power local cck 50
power local ofdm 30
channel 2452
station-role root bridge
cca 75
concatenation
distance 1
antenna receive right
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
full-duplex
bridge-group 1
bridge-group 1 spanning-disabled
hold-queue 80 in
interface BVI1
ip address 192.168.1.1 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end
show run
Building configuration...
Current configuration : 1815 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname xxxxx
enable secret 5 $1$SN2n$CLPRLRzAjlUD47jR1ugca.
clock summer-time BST recurring last Sun Mar 1:00 last Sun Oct 2:00
ip subnet-zero
ip domain name xxxxxx
ip name-server 1.1.1.1
ip ssh time-out 60
ip ssh authentication-retries 2
ip ssh version 2
aaa new-model
aaa authentication login xxxxx
aaa session-id common
dot11 ssid xxxxx
max-associations 1
authentication open
authentication key-management wpa
infrastructure-ssid
wpa-psk ascii xxxxx
username Cisco password 7 062506324F41
username xxxxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxxxx
parent 1 003a.9a21.a8b0
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
station-role non-root bridge
antenna receive left
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
full-duplex
bridge-group 1
bridge-group 1 spanning-disabled
hold-queue 80 in
interface BVI1
ip address 192.168.1.2 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end
Regards NeilHi Scott,
Yes they are very close together, about a meter to be exact,
Sorry im by no means clued up on wireless, so im guessing your after these
e#show dot11 associations all-client
Address : 003a.9a21.b4c0 Name : xxxxxx
IP Address : 192.168.1.2 Interface : Dot11Radio 0
Device : 11g-bridge Software Version : 12.3
CCX Version : NONE
State : Assoc Parent : self
SSID : xxxxxxxx VLAN : 0
Hops to Infra : 1 Association Id : 4
Clients Associated: 1 Repeaters associated: 0
Tunnel Address : 0.0.0.0
Key Mgmt type : WPA PSK Encryption : TKIP
Current Rate : 54.0 Capability : WMM ShortHdr ShortSlot
Supported Rates : 1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Voice Rates : disabled
Signal Strength : -31 dBm Connected for : 135 seconds
Signal to Noise : 67 dBm Activity Timeout : 30 seconds
Power-save : Off Last Activity : 0 seconds ago
Apsd DE AC(s) : NONE
Packets Input : 101726 Packets Output : 198208
Bytes Input : 10283192 Bytes Output : 257691877
Duplicates Rcvd : 0 Data Retries : 10049
Decrypt Failed : 0 RTS Retries : 0
MIC Failed : 0 MIC Missing : 0
Packets Redirected: 0 Redirect Filtered: 0
Session timeout : 0 seconds
Reauthenticate in : never
the above is after issuing the power statements
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxxxx
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
no power client local
power client 1
power local cck 1
power local ofdm 1
station-role root bridge
cca 75
concatenation
distance 1
antenna receive right
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxx
parent 1 003a.9a21.a8b0
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
no power client local
power client 1
power local cck 1
power local ofdm 1
station-role non-root bridge
antenna receive right
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
end
or
show int dot 0
Dot11Radio0 is up, line protocol is up
Hardware is 802.11G Radio, address is 003a.9a21.a8b0 (bia 003a.9a21.a8b0)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 21/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:07:23, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 36
Queueing strategy: fifo
Output queue: 0/30 (size/max)
5 minute input rate 105000 bits/sec, 224 packets/sec
5 minute output rate 4630000 bits/sec, 440 packets/sec
231658 packets input, 14164388 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
448016 packets output, 581607544 bytes, 0 underruns
16 output errors, 0 collisions, 4 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
I can serperate them by atlease 10 meters down the hallway... , What is the likely hood of actually getting 54.0 when they are deployed, Distance no more that 1Km) how do these stats look?
Neil -
How to load and show PDF on stage in Flash using AlivePDF or PurePDF external libraries?
Hello,
I searched a lot on internet but didn't find a proper way to load and open/show PDF on stage in Flash. Following are my understandings about this topic.
I know Flash does not have the built-in functionality to load and show pdf document on stage.
I know you can do this in AIR application using HTMLLoader class but it required adove reader to be installed on your machine.
I have used AlivePDF/PurePDF and I know how to export/generate a PDF File using these libraries but I don't know how to use them to load and show PDF document on stage in Flash. According to my research, I think these libraries can accomplish my task but how, I don't know. That's because I am here for your help.
People suggest to first convert pdf into an image or swf file and then import it into Flash but I don't want this solution because my clients will be importing/uplading PDF file into my software.
Some people suggest to "Convert PDF renderer code written in C/C++ using Alchemy to flash library" and then use that library to my project. I don't have any idea how to do this. If anyone can help me to achieve required functionality this way, please guide me.
Now you know about my understandings, so you can guide me in better way. Let me give you an example what kind of functionality I want. Please visit: https://www.pdffiller.com. Upload a pdf file there and you will see that it shows that pdf to user (At the moment, I want this functionality) and pdf annotation i.e. write text on pdf and other functionalities.
NOTE: I am not a Flex and AIR developer. I am a Flash (Actionscript 3.0) Developer. So please first help according to flash. If you want to offer the solution according to Flex and AIR, you are most welcome.
I specially want "ADOBE EXPERTS - Adobe Flash developer from Adobe" to comment on this and help me out. It's about 4th day I am without a solution. I am afraid, I'll loose my client if I'll not have a solution in next couple of days.
Thanks,
momersaleem
eLearning SpecialistJust to throw in a $0.02, I looked at those libraries myself quite a while ago and all they had the ability to do was give you information and assets from the PDF. At that point you literally had to read each page in the PDF (whatever the library could extract), use the information it extracted (position, type size, images, etc) and create a layout engine that could "reconstruct" the page piece by piece.
I hope it's better these days but that's what I took from those libraries quite a while ago and it may still be true. That would explain "Convert PDF renderer code written in c/c++ using Alchemy to flash library". Someone may already have written a quality layout engine. Otherwise there was no "load pdf, run this ShowPDF() function to add to display list" functionality at all. -
has anyone else been totally ripped off by this company i know seven different people just family and friend who have totally screwd by them and when they call in and ask questions the people who work for verizon don't care they will even tell you to switch to straight talk KathleenCharlotteSJudyKeplerchristineRobbJustineKBGJoeCoVerizon Wireless ServicesPaulVerizon Wireless Services
i guess i really want to get ahold of someone in charge of our area because after the last hole month of being treated like a dog by them and being told they don't care I'm just willing to go to any lengths to see a company like that is not successful I'm a business owner to actually several businesses and your customers are the only reason your there but you can never forget about the little people verizon
-
HT5569 How do I print using a wireless printer when I'm using wifi for Internet at the same time
I can't figure out how to print via wifi when I'm using wifi for Internet at the same time please help
You need to have your printer & ipad connected to the same wifi router. ( This would be my best guess. )
Robert -
Should I have purchased a wired keyboard?
First make sure the batteries aren't dead and that the keyboard hasn't already been paired with another device. If it hasn't, the keyboard should pair automatically when you reboot. You may have to press and hold the power button on the right side of an Apple keyboard until the LED starts flashing.
Otherwise see these support articles:
Mac mini (Mid 2011 and later) and iMac (Late 2012): Bluetooth keyboard may not pair during Setup Assistant
Apple Wireless Keyboard: Difficulty during pairing process
If you have a third-party Bluetooth keyboard, you may need a wired keyboard to complete the pairing process. It's a good idea to keep a cheap wired keyboard and mouse or trackball as backups for a desktop Mac anyway, because Bluetooth isn't completely reliable. -
I want to send to my secretary's wireless printer, but I have an ethernet cable connecting my computer to the internet. Can I have both an internet and wireless connection so I can use the wireless network to send to her printer?
Is your computer connected to the same local network as your secretary's? If you have a router that provides both the wireless and wired network access for your business it should be possibe to access the printer wirelessly. In my setup here I have a combination of wired and wireless computers accessing a couple of wireless printers as well as three on the wired network. You may need to configure your router to allow the wored and wireless segments to communicate through your router. I will move this post to the Printer Networking and Wireless forum for better responses.
It would probably help to give some details of the printer model as well as the details of your router and woreless connections.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V -
How to select distinct values from a table when it has composite primary ke
Hi
I have the requirement like , I need to select distinct one column values from the table which has composite primary key. How to acheive this functioinality using view object.
Eg : Table 1 has col1 and col2, col3
col1 col2 col3
1 A NA
1 B NA
2 A NA
3 C NA
2 D NA
primary key (col1,col2)
I have to select distinct col1.
ThanksHi
I got the solution for above. By Creating the read only view object we can acheive this.
thanks -
How do you get songs off of itouch when it has been sycned with another computer
How do you get songs off an ipod touch to a new computer when the ipod touch has been synced with another computer. The other computer died. Thanks!
You don't. Unless they were purchased from the iTunes store, then you can go to File > Transfer purchases. Or you can right click (ctrl click if you're on a Mac) on the name of the device in the source list in iTunes and then choose Transfer purchases.
http://support.apple.com/kb/HT1848
Maybe you are looking for
-
In J1IIN the excise invoice type is not getting changed to BOND for Export
Hi Experts, In ECC 6.0 I am trying to create an Excise Invoice (Export) but the system in J1IIN is not allowing me to change Excise invoice type to Bond (deemed is reflecting in Blue), some more details are as follows: The Customer is for Country Ind
-
Script for saving/replacing .png´s
For Photoshop CS5: Hi, I need a script, which allows me to take the .png file i am working on, and save and replace it in the existing location with the exact same name: Without creating the "copy.png" string and preferebly without have to choose "In
-
anyone out there use the Alarm Clock app? it looks great its easy to set up but mine didn't go off this morning (good job i had a back up!) it says to set the alarm and leave it running in the background i did this but nada - nothing anyone else have
-
G4 display went black. Please help.
My screen will not wake up. Once I move the mouse, the screen will show for about a second and then it goes back to black. The display light is on and the computer seems to be working. I've tried shutting it down, vacumming the port, pressing f2 to c
-
Confirmation - Work Center - Routing
Hi all, I try to understand routings. When i try to confirm an operation with BAPI_PRODORDCONF_CREATE_TT for a work center which is not defined in routings, it returns no problem. But it is not in routing. How can it be confirmed? Or what changes whe