"Restart Now" IOS command for 1310 Wireless Bridge

I have 2 Cisco Aironet 1310 wireless bridges setup, line-of-sight, 3/4 mile apart, one as Root, the other as Non-Root. Occasionally they drop their connection but a hard restart of either or both bridges will reestablish the connection. What is the equivalent IOS command to the
"GUI > System Software > System Configuration > Restart Now" command? I would like to be able to telnet to either/both units and issue/script the appropriate command.

the command is "reload"
BRIDGE# reload
Regards
Surendra

Similar Messages

Power Injector for 1310 wireless bridge

Hello,
We have a failed power injector on a 1310 series bridge. Will the "Power Injector LR" from a 1410 series bridge work on the 1310?
Thank you,
Matt

No... both have a different output and should not be used interchangeably.
See this post by Surendra:
https://supportforums.cisco.com/message/3280050#3280050
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

1310 Wireless Bridge problems

I have a 1310 wireless bridge....when I power it up, it sometimes does not boot up. The I LED will just sit there and blink and the R and E LEDs will blink in unison with it. After a while just the I LED blinks. I cannot find any literature that tells me if this is an error code or not.
Also, when the thing does boot up, it tells me that the Radio interface is down and disabled, when in fact if you go into the settings of the radio interface, it is selected to be enabled.
What might be going on here?
Thank you.

No, there is nothing on the console port when the thing is in the condition described above.
If I do get a successful boot, I can then access via a console port. I may try to reinstall firmware and see if that fixes the problem.
So you are saying the radio link will show as disabled/down until it actually tries to associate/authenticate with another bridge unit? That is normal?

Need help with IOS commands to see wireless printer

Seems that I'm not asking the question correctly, or providing the right information.
The problem:
I've purchased a wireless printer, (an HP 6500a) and I can not see / ping / use the printer on the wireless network.
Environment:
Cisco 891 ISR in standalone. Single office - Home-office environment. Nothing spectacular. WLAN connected and operational to the internet.
The printer is configured to use a static IP of 10.0.0.3 and reports that it is connected to the AP. However, when I ping FROM the command line at the AP, I DO NOT see the printer. (I did previously, but we lost power last night due to a storm and I'm still trying to reconfigure it...) DHCP is configured on the router to exclude the range 10.0.0.1 through 10.0.0.99
How do I configure the wireless router to allow any connected client to share files / printers etc? Seems that the Cisco router has this shut off
by default and I've found nothing in the user manual or by asking for help on here how to reverse this so that I can share printers / files on the LAN.
Please, I'm not stupid, but I'm only casually familiar with IOS and Cisco's networking terms.
Thanks in advance,
-Mike
=============== Begin Wiresless AP config (running-config) ==============
Current configuration : 3122 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname (Remnoved)
enable secret 5 (Removed)
no aaa new-model
dot11 syslog
dot11 ssid (Removed)
   vlan 1
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii 0 (Removed)
username (removed)
username (Removed)
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers tkip
broadcast-key vlan 1 change 30
ssid (Removed)
antenna gain 0
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 1 mode ciphers tkip
broadcast-key vlan 1 change 30
ssid (Removed)
antenna gain 0
dfs band 3 block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
access-list 110 permit icmp any any echo
access-list 110 permit icmp any any echo-reply
access-list 110 permit icmp any any source-quench
access-list 110 permit icmp any any packet-too-big
access-list 110 permit icmp any any time-exceeded
bridge 1 route ip
banner login ^CC
% Password change notice.
Default username/password setup on AP is cisco/cisco with privilege level 15.
It is strongly suggested that you create a new username with privilege level
15 using the following command for console security.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want to
use. After you change your username/password you can turn off this message
by configuring "no banner login" and "no banner exec" in privileged mode.
^C
line con 0
privilege level 15
login local
no activation-character
line vty 0 4
login local
cns dhcp
end

Wireless clients can get on w/o issue. Nobody can ping anyone else or see them.
No file sharing, no printer.
Tried using the web-based config which works for some items, but wont access the advanced config.
I'm on my way into town, so can't post the router config, but it is posted in my earlier question
of last week. I can login later if you otherwise need it here.
Thanks,
-Mike

How to load SW in 1310 wireless bridge when flash has no SW-image

During an upgrade (autonomous software), I indicated that the system should create enough room to load the new software.
However, while loading the new software, the system crashed, so no image at all is left in flash.
How can I load a software image in the wireless bridge ?
In old days with routers this was possible with some x-protocol over the console connection.
Is there any description on how to handle this on a wireless bridge.
I always end up in the boot mode.
Thanks

If the device doesnt have an image, type reset on the boot console, When it comes up , if will ask for certain options
set IP_ADDR
set NETMASK
set DEFAULT_ROUTER
set IP_ADDR
set NETMASK
set DEFAULT_ROUTER
Make sure the value (IP_ADDR, NETMASK .. ) are copied exactly, other wise it will not work, Once you have copied, if you type set, you can seet these values.
After this type the following commands
tftp_init
ether_init
flash_init
and then
tar -xtract tftp:/// flash:
and boot
Thanks
NikhiL

Enable AES encryption on 1310 Wireless bridge

Hi All,
I have requirment to enable the AES encryption on the management VLAN traffic between connected root and non root bridges . can any one share the configuration guidelines please ??
below is the network setup .
Router<---->SW1 ( main office)--> Root-bridge < ---------->non root-bride------SW2 ( remote end site)
Apart from the specific configuration on the wireless bridge is any extra configuration required on the Switch interfaces??
Regards
Lerner

Hello,
1. Make sure you are running version 12.3(7)JA or later since WPA2/AES was not always available for the 1310.
2. How do you currently have the root/non-root configured?
Ideally, adding AES shoudl be fairly straight forward. Keep in mind we recommend using WPA2 with AES.
configured on your root AND non-root:
dot11 ssid
authentication open
authentication key-management wpa version 2
interface do1
encryption mode ciphers aes-ccm

Suggested IOS for 1532i Wireless Bridge

Hello all,
I'm currently running IOS version 15.2.4-JB3b(ED) for two autonomous point-to-point bridges. I'm having difficulty getting one of the bridges to stop flapping and autonegotiating at 10/full. The other side seems to be stable and will autonegotiate at 1000/full. I've had a 2nd cable run installed and terminated. I've tried rebooting both the power injector and the bridge in question. I've tried setting the switch port and bridge to 1000/full statically. But all my attempts to resolve this issue has failed. I'm not sure if this version of IOS for the 1532s are buggy but can someone point me to which IOS has been stable for them? Thanks!
Regards,
Terence

Hi Terrence,
Did you try this one ? It is released when 8.0 came out & worth trying.
ap1g3-k9w7-tar.153-3.JAB.tar
NB: I haven't got those AP model in my environment,so does not have first hand experience.
HTH
Rasika
**** pls rate all useful responses ****

AT Commands for Verizon Wireless USB760?

This cellular modem seems to respond to some AT commands (like AT+CSQ and AT+IPR?), but not other (like AT+CREG?). Novatel Wireless technical support and Verizon Wireless technical support have not responded to my queries regarding what AT commands ARE supported by the modem. I tried AT+CLAC, which is supposed to cause the modem to list all supported AT commands, but, surprise, that command is not supported either. Can anyone point me toward a list of the AT commands that this modem supports?
Thanks,
Don

I know this is an old post but for future researchers, these are the commands to reset the USB devices used with VZAM. These are to used with great care as you could mess up your device if entered incorrectly.
When you open it again it will rebuild the proper files and should resolve this concern.
*Note: The commands must be typed precisely as shown or it can render the device unusable if customer gets it wrong have the exit the window and try again.
1. Open VZ Access Manager
2. Hold down the Control button and type T (this should open the DOS prompt box)
3. Type ATZ and then click the Enter key (it should then respond OK)
4. Type AT$QCMIPP=0 (the last character is a zero) and then press the Enter key (it should then respond OK)
5. Type AT$QCMIPEP=1 and then press the Enter key (it should then respond OK)
6. Type AT$QCMIPGETP and then press the Enter key (device information will be displayed)
7. Close VZ Access Manager
When you open it again it will rebuild the proper files and should resolve this concern.

1310 Wireless Bridge Poor performance

Hello I am getting really bad performance on a bridge i am trying to get up,
Laptop - Switch - AIR-BR1310G-E-K9-R attena-ed ----------------
attena-ed AIR-BR1310G-E-K9-R switch laptop.
When doing an FTP Transfer i get a poor 1MB, these are currently in a lab enviroment, this is a far cry from what i am hoping for,
can anyone see an issue
show run
Building configuration...
Current configuration : 1892 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname site1
enable secret 5 $1$XQ0Z$Fzjg/dJ/I1sY5bLjss0l4/
clock summer-time BST recurring last Sun Mar 1:00 last Sun Oct 2:00
ip subnet-zero
ip domain name xxxxxx
ip ssh time-out 60
ip ssh authentication-retries 2
ip ssh version 2
aaa new-model
aaa authentication login xxxxx
aaa session-id common
dot11 ssid XXXXXX
   max-associations 1
   authentication open
   authentication key-management wpa
   infrastructure-ssid
   wpa-psk ascii xxxxxxxxxxxxxxxxxxx
username Cisco password 7 047802150C2E
username xxxxxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxxx
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
no power client local
power client 50
power local cck 50
power local ofdm 30
channel 2452
station-role root bridge
cca 75
concatenation
distance 1
antenna receive right
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
full-duplex
bridge-group 1
bridge-group 1 spanning-disabled
hold-queue 80 in
interface BVI1
ip address 192.168.1.1 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end
show run
Building configuration...
Current configuration : 1815 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname xxxxx
enable secret 5 $1$SN2n$CLPRLRzAjlUD47jR1ugca.
clock summer-time BST recurring last Sun Mar 1:00 last Sun Oct 2:00
ip subnet-zero
ip domain name xxxxxx
ip name-server 1.1.1.1
ip ssh time-out 60
ip ssh authentication-retries 2
ip ssh version 2
aaa new-model
aaa authentication login xxxxx
aaa session-id common
dot11 ssid xxxxx
   max-associations 1
   authentication open
   authentication key-management wpa
   infrastructure-ssid
   wpa-psk ascii xxxxx
username Cisco password 7 062506324F41
username xxxxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxxxx
parent 1 003a.9a21.a8b0
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
station-role non-root bridge
antenna receive left
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
full-duplex
bridge-group 1
bridge-group 1 spanning-disabled
hold-queue 80 in
interface BVI1
ip address 192.168.1.2 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end
Regards Neil

Hi Scott,
Yes they are very close together, about a meter to be exact,
Sorry im by no means clued up on wireless, so im guessing your after these
e#show dot11 associations all-client
Address           : 003a.9a21.b4c0     Name             : xxxxxx
IP Address        : 192.168.1.2        Interface        : Dot11Radio 0
Device            : 11g-bridge         Software Version : 12.3
CCX Version       : NONE
State             : Assoc              Parent           : self
SSID              : xxxxxxxx        VLAN             : 0
Hops to Infra     : 1                  Association Id   : 4
Clients Associated: 1                  Repeaters associated: 0
Tunnel Address    : 0.0.0.0
Key Mgmt type     : WPA PSK            Encryption       : TKIP
Current Rate      : 54.0               Capability       : WMM ShortHdr ShortSlot
Supported Rates   : 1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Voice Rates       : disabled
Signal Strength   : -31 dBm           Connected for    : 135 seconds
Signal to Noise   : 67 dBm            Activity Timeout : 30 seconds
Power-save        : Off                Last Activity    : 0 seconds ago
Apsd DE AC(s)     : NONE
Packets Input     : 101726             Packets Output   : 198208
Bytes Input       : 10283192           Bytes Output     : 257691877
Duplicates Rcvd   : 0                  Data Retries     : 10049
Decrypt Failed    : 0                  RTS Retries      : 0
MIC Failed        : 0                  MIC Missing      : 0
Packets Redirected: 0                  Redirect Filtered: 0
Session timeout   : 0 seconds
Reauthenticate in : never
the above is after issuing the power statements
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxxxx
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
no power client local
power client 1
power local cck 1
power local ofdm 1
station-role root bridge
cca 75
concatenation
distance 1
antenna receive right
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid xxxx
parent 1 003a.9a21.a8b0
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
no power client local
power client 1
power local cck 1
power local ofdm 1
station-role non-root bridge
antenna receive right
antenna transmit right
antenna gain 13
world-mode dot11d country GB outdoor
infrastructure-client
bridge-group 1
bridge-group 1 spanning-disabled
end
or
show int dot 0
Dot11Radio0 is up, line protocol is up
Hardware is 802.11G Radio, address is 003a.9a21.a8b0 (bia 003a.9a21.a8b0)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
     reliability 255/255, txload 21/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:07:23, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 36
Queueing strategy: fifo
Output queue: 0/30 (size/max)
5 minute input rate 105000 bits/sec, 224 packets/sec
5 minute output rate 4630000 bits/sec, 440 packets/sec
     231658 packets input, 14164388 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     448016 packets output, 581607544 bytes, 0 underruns
     16 output errors, 0 collisions, 4 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
I can serperate them by atlease 10 meters down the hallway... , What is the likely hood of actually getting 54.0 when they are deployed, Distance no more that 1Km) how do these stats look?
Neil

1300 Wireless Bridge

I have been using two 1310 wireless bridges for about six months now. They have been working very well. However this morning they stoped connecting and one says that the Software status is disabled and the hardware status is down.
in the configuration the Radio is enabled and one is set to root the other to non-rooot. Nothing changed just stopped working. I even tried switching witch is root and Non-Root. The problem stays with the Non-Root.
Thanks
Phillip

Try this link. Should help you:
http://www.cisco.com/en/US/products/hw/wireless/ps5279/products_tech_note09186a0080508551.shtml

Wireless Bridge by Aironet 3700i

I'd like to connect two network by using two Aironet 3700i APs like
NW1 -- AP1 -- AP2 -- NW2
I want to confirm that this is possible by simply setting AP1 = Root Bridge and AP2 = Non-Root Bridge.
I also want to confirm that this is possible even when AP2&NW2 are moving and connect to AP1 temporarily.

When you configure AP2 as workgroup bridge, then it will act as a wireless client. So it will associate to any normal AP (other AP no need to be the root bridge). Also you can modify the roaming behaviour so it will roam to different AP like any other client when moving.You can refer this to configuration options available on this
http://mrncciew.com/2013/07/24/wgb-roaming-part-1/
You can configure multiple vlan with WGB & you can refer below for that
http://mrncciew.com/2013/06/16/ios-ap-wgb-with-multiple-vlan/
If it is does not require that sort of roaming & always you will align with AP1 then you can configure it as Root Bridge & Non-Root-Bridge. Here is a reference configs for a wireless bridge
http://mrncciew.com/2013/11/09/wireless-bridge-with-eap-fast/
**** Pls do not forget to rate our responses if that is useful to you ****
HTH
Rasika

Wireless bridge can't access windows certificate server

We have 10 Cisco 1200 wireless APs. The VLAN 1 use Windows certificate as authentication and VLAN 100 for the public. They work fine. We just bought two 1310 wireless bridges for outdoor use. We contact Cisco support for setup these two bridges. The wireless can receive the signal but can't logon. The IP is 169.254.x.x. The Certificate server receive Event ID 2 as below. The Cisco engineer can't make it work and he said the setup Windows IAS is not his expertise. Any suggestions how can we fix this issue?
Event Type: Warning
Event Source: IAS
Event Category: None
Event ID: 2
Date: 4/13/2007
Time: 7:41:21 PM
User: N/A
Computer: DEVICES
Description:
User blin was denied access.
Fully-Qualified-User-Name = chicagotech.net/Users/Bob Lin
NAS-IP-Address = 10.0.20.54
NAS-Identifier = Outdoor_1300_2
Called-Station-Identifier = <not present>
Calling-Station-Identifier = <not present>
Client-Friendly-Name = Root Bridge1
Client-IP-Address = 10.0.20.54
NAS-Port-Type = Async
NAS-Port = <not present>
Proxy-Policy-Name = Use Windows authentication for all users
Authentication-Provider = Windows
Authentication-Server = <undetermined>
Policy-Name = All
Authentication-Type = PAP
EAP-Type = <undetermined>
Reason-Code = 66
Reason = The user attempted to use an authentication method that is not enabled on the matching remote access policy.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 00 00 00 00 ....

There are too many variables at play here, and too many unknowns...both on the server and client side...so it would be hard for anyone to offer suggestions other than the face you should talk to your system/network admins.

Wireless Bridge Solution

Hello,
I am looking for a wireless Bridge Solution the distance between 2 buildings is 200 Metre approx and the height of the buildings are 24 metres. The desired bandwidth is 11 Mbps and above.
Please help me in finalizing the solution. I am looking for a cheap solution other than 1300, 1400 or 1500 solution.
Regards..

You can always use a 1242 in bridge mode with external antennas. You will need a NEMA heated/cooled enclosure for the ap unless that will be mounted indoors, lightning arrestor and LMR cable to extend the antenna if required and antenna mounting hardware. But with most systems, you will need line of site, so hopefully you have this. Antenna wise, you can go with a yagi at both ends.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps6521/prod_qas0900aecd8031c8dc.html
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/product_data_sheet09186a008008883b.html

Wireless bridge supporting igmp

Has anybody got suggestions for a wireless bridge I can use on my youview setup.
Tried a few 18 months ago, iplayer and nowtv worked but not IP channels.
At the time I suspected it was down to incorrect igmp routing, my powerline setup is becoming problematic so I'm returning to a wireless solution
Does anyone have a confirmed working wireless solution with ALL the ip facilities of youview including premium IP channels?
My router is an older style bt homehub
Ta
Steve

the reason why this doesnt work is that a BT HH3 doesnt pass IGMP/multicast packets onto the wireless AP.
The supposed reason being that multicast could swamp the wireless network.
It doesnt matter what client one uses, if IGMP packets arent passed to the wireless AP (by the router) then would wont be able to use youview wirelessly.
by "use" I mean IPTV multicast channels (essentials BT sport etc) NOT iplayer of nowtv.
anybody claiming to have IPTV channels working with a HH3 over wirelss is telling porkies, unless they know something that I dont.

Information about mounting kit for 1310

Hi,
I have some 1310 with integrated antenna and I would to install some of them as an access-point in indoor environment.
I am wondering about which mounting kit choose to install it on a wall.
Is it right to use the mounting kit with product code AIR-ACCRMK1300?
Thx in advance
antonio

Hi Antonio,
I am truly sorry my friend
I didn't see the restriction you most correctly noted. Here is why
it won't work;
Q. Is it possible to combine the wall mount kit with an internal antenna on the 1300 Bridge?
A. No. The internal antenna would point into the wall when you use the wall mount. Also, the wall mount can accommodate the antenna.
Q. Is it possible to adjust a 1310 Wireless Bridge with an internal antenna that is installed on a wall mount kit, or is it fixed?
A. It is a fixed solution. Therefore, you should use an external antenna when you use a wall mount kit.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_q_and_a_item09186a008015502c.shtml#walll1
Cheers!
Rob

"Restart Now" IOS command for 1310 Wireless Bridge

Similar Messages

Maybe you are looking for