How to make Vi file as input file in Event structure?

Hiii All..
i got problems when to construct a event structure. The file input (vi format) doesnt have source of wire connection to conect the wire (shift register) .For your information the vi that i create only contain simple mathematical equation.
I already study the New Event Handler Example. but the file input for that example (acquire data.vi) have a source of connection. anyone can help me?
thank you very much
[email protected]
Solved!
Go to Solution.
Attachments:
TOTAL.vi ‏18 KB

Well, in your subVI you do need to wire up some inputs and outputs to your connector panel. As I said, a basic LabVIEW skill that you will find in the tutorials.
You have a number of inputs to your subVI. More than you would want to attach to a connector panel. You should perhaps use a cluster to group them together.
To get you started, here are the steps to connect a control or indicator to the connector panel.
1. Open subVI.
2. Right click on icon at upper right. Show Connector.
3. Hover over a block you want to be a connector terminal, it will change to a spool of wire. Click.
4. Go to the control or indicator on the front panel that you want to associate it with. Click again.
5. Repeat as needed for other controls and indicators and save your subVI. Now the subVI instance in your main VI can have wires connected to it.
You should plan your connector panel so that controls are on the left side of the panel, and indicators on the right. This will allow data to "flow into" and "flow out of" the subVI in a normal looking left to right orientation.

Similar Messages

How to make Finder NOT to show files from a specific folder in "All My Files"?

Hello!
Can someone please advice how to make finder NOT to show files from a specific folder in "All My Files"? See the attach - I recently installed Civilization 5 from Steam and now I have a lot of unneeded files (*.log and *.ini) shown in All My Files colder in Finder.
I don't want to see them. Any advise?

Using "All my Files" was very handy before all this rubbish popped up. =(

How to make mplayer play 3gp type files ??

how to make mplayer play 3gp type files ??
I downloaded a Japanese blue movie by amule, but I cannot play it!

Army wrote:Actually, a few weeks ago, opencore-amr went into [extra] and ffmpeg and mplayer are being compiled against it, so Arch's mplayer should support 3gp files ootb including audio. Video playback was never an issue, because 3gp is just a container, the video codec is usually h263 or h264, which are no problem for mplayer.
Very new versions of FFmpeg have native amr-nb support. I'm not sure if it happened before or after the most recent FFmpeg bump in the repos.

How to make photoshop cs4 open dng files?

How to make photoshop cs4 open dng files?

They are opened by Photoshop through the ACR plug-in you should make sure the ACR 5.7 update is installed for your CS4.
Adobe - Photoshop : For Macintosh
Adobe - Photoshop : For Windows

The file size of selected file in input file control is shown as 0 for multiple file selection in Safari 5.1

The file size of selected file in input file control is shown as 0 for multiple file selection in Safari 5.1. If you select single file, then it is able to return file size correctly. However, if you select multiple files, then the file size of each of the selected file is always returned as 0 from javascript. This works correctly in Safari 4.0 but it does not work in Safari 5.1.
How do I get the correct file size in Safari 5.1 ?

If you want to post (or send me) a link to the lrcat file, I'd take a look at it for you, and give you a break-down what's consuming all the bytes. But it might be fun to learn how to do that yourself (e.g. using SQL). I use SQLiteSpy, but other people have their favorites.. (or you can use a command-line client if you prefer..). One way: just run "drop table "{table-name}" on each table then look at filesize (do this to a copy, not the real thing).
Anyway, it's hard to imagine keywords and captions etc. taking much of the space, since even if you had 1000 10-character words of text metadata per photo average that still only adds up to 117MB, which isn't a substantial portion of that 8G you're seeing occupied.
Anyway, if you've painted the heck out of most of them and not cleared dev history, that'll do it - that's where I'd put my money too...
One thing to consider to keep file-size down:
===================================
* After reaching a milestone in your editing, take a snapshot then clear edit history, or the top part of it anyway (e.g. leave the import step), using a preset like:
Clear Edit History.lrtemplate
s = {
    id = "E36E8CB3-B52B-41AC-8FA9-1989FAFD5223",
    internalName = "No Edit",
    title = "Clear Edit History",
    type = "Develop",
    value = {
        settings = {
            NoEdit = true,
        uuid = "34402820-B470-4D5B-9369-0502F2176B7F",
    version = 0,
(that's my most frequently used preset, by far ;-})
PS - I've written a plugin called DevHistoryEditor, which can auto-consolidate steps and reduce catalog size - it's a bit cumbersome to use a.t.m. but in case you're interested...
Rob

How to make a form for input in web interface builder

Hi expert:
How to make a form for input in web interface builder?I have already used it to do PS planning, but I don't know how to draw lines and checkboxes . Thanks in advance.
Allen

WAD:
Open the WAD and create a new template. On the left hand navigation you will have several Web Items available. Under 'Standard' you have 'Analysis' item. Pull that into your template to the right. Under the Properties tab you need to pick the query [form/layout] that you have built in Query Designer.
You will also find other items such as Button group, Checkbox, drop down, list box etc available. Pick and drag into the template whatever it is you require. Lets say you want a button. Under the Properties tab select the 'Command' that you require. You could use standard commands that are available there. You could also define functions and commands that you require.
Query Designer:
Open the QD and drag the characteristics and key figures that you require into the rows and columns of the QD. You would need to specify restrictions under the Filter tab of the QD based on the granularity of data that you require. You would need to remember that the key figures need to be made Input Ready [do this by clicking on KF and on the planning tab select "change by user and planning functions"].
This shouldgive you a start. After you've explored it yourself a bit we can discuss further and I can certainly provide you additional details/material on these areas.
Srikant

How to make English and Chinese pdf files searchable?

I have scanned many A4 English and Chinese print-outs into pdf format. How to make these files searchable ? People mention about the OCR issue. Will the installation of Adobe make life easy and manageable?

I know Acrobat does Japanese OCR very well; I can only assume that it works for Chinese as well.
P.S. I just checked: Chinese (Simplified) and Chinese (Traditional) are both language selection options for OCR.

How to make Folder Action work on file, subfolder content change?

Hi!
I looking for information in how to make a Folder Action, Work Flow or any action from Automator to work on file change and not only on deletion, moving or insertion. What I want to know is if it's possible to trigger some script or app while monitoring a folder and its contents, files and subfolders, changes. Meaning that when I have a file that has its contents updated the action will be triggered like an txt file that I only insert a new line in it, for example.
Is there any solution that is not third party? Is there an internal Mac OS X solution that would work on Snow Leopard, Lion and Mountain Lion?

i have same problem. i would like to move automatically saved Word backup copy to another folder, but the folder action doesn't recognize the save as a new file that needs to be acted upon.

How to merge five different xml input files into three output files

Hi All,
Can you please explain me to merge 5 different xml input files into 3 output xml files.
I'm looking forward for ur suggestions...
Thanks
Pullarao

HI
Please see the below links
/people/pooja.pandey/blog/2005/07/27/idocs-multiple-types-collection-in-bpm - Collection of IDoc to Single File
http://help.sap.com/saphelp_nw04/helpdata/en/3c/831620a4f1044dba38b370f77835cc/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/62/dcef46dae42142911c8f14ca7a7c39/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/de/766840bf0cbf49e10000000a1550b0/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/cb/15163ff8519a06e10000000a114084/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/08/16163ff8519a06e10000000a114084/content.htm
Many other examples can be found under the following link at help.sap.com
http://help.sap.com/saphelp_nw04/helpdata/en/14/80243b4a66ae0ce10000000a11402f/frameset.htm
And some weblogs
https://weblogs.sdn.sap.com/pub/wlg/1403 [original link is broken] [original link is broken] [original link is broken]
/people/siva.maranani/blog/2005/05/22/schedule-your-bpm *****
/people/krishna.moorthyp/blog/2005/06/09/walkthrough-with-bpm
/people/michal.krawczyk2/blog/2005/06/11/xi-how-to-retrieve-messageid-from-a-bpm
/people/arpit.seth/blog/2005/06/27/rfc-scenario-using-bpm--starter-kit
/people/sravya.talanki2/blog/2005/08/24/do-you-like-to-understand-147correlation148-in-xi
/people/michal.krawczyk2/blog/2005/09/04/xi-do-you-realy-enjoy-clicking-and-waiting-while-tracing-bpm-steps *****
/people/udo.martens/blog/2005/09/30/one-logical-system-name-for-serveral-bpm-acknowledgements *****
/people/sudharshan.aravamudan/blog/2005/12/01/illustration-of-multi-mapping-and-message-split-using-bpm-in-sap-exchange-infrastructure
/people/kannan.kailas/blog/2005/12/07/posting-multiple-idocs-with-acknowledgement
Also have a look at these seminars,
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/media/uuid/daea5871-0701-0010-12aa-c3a0c6d54e02
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/media/uuid/e8515171-0701-0010-be98-e37bec4706cc
<b>BPM CollectPattern..</b>
http://help.sap.com/saphelp_nw2004s/helpdata/en/08/16163ff8519a06e10000000a114084/frameset.htm
Thanks !
Regards
Abhishek Agrahari
Questions are welcome here!!
<b>Also mark helpful answers by rewarding points </b>

How to make timecode track in transcoded file match original

Using Compressor 4.1.3, when I make an H264 QT from a DNX36 QT, the timecode track does not replicate properly. The first frame of timecode repeats for a frame which makes every frame after that read as one frame earlier than it is in the original file.
For example, the first frame of the original file is 01:00:00:00. In the H264, the 1st and 2nd frames are 01:00:00:00, and the 3rd frame is 01:00:00:01. The 3rd frame should be 01:00:00:02.
The DNX36 is a QT Reference movie exported from Avid MC 7.0.4.1. I am reading the timecode on the QuickTimes using QuickTime Player 7.6.6. This works correctly with Mac OS 10.7.5 and Compressor 3.5.3.
The system I'm having the trouble on is Mac OS 10.9.4, Compressor 4.1.3
Any ideas on how to make the timecode track of the transcoded file match the original?
Thanks.

I'm not sure what you are getting at. Is a string child the contents of a node treated as text?
If you are trying to match a child node regardless of case I doubt this is possible as the XML standard says an XML document is case sensitive so if your parser ignored case it would not be XML complient.
Hope this helps.

How to make the active save-to-file with the data from GPIB ?

Hello,,everybody !!
I want to make the active save-to-file with the data from GPIB since starting the measurement. To save-to-file at the end of measurment is somehow risky for losing the data because my measurment have to take for long time (eg. 24-48 hours).
Thank you in advance for anybody's help !!

Thanks Dennis,
I have already append, I got it but still have one small problem that between each line it has the blank line. Example as below ,
16:40:33 54.24
16:40:34 54.23
16:40:35 54.24
I want to get rid of the blank line in between.. Do you have the idea about it ?

File adapter input file format

Here the communication scenario is as follows: read a file and send a message via XI to an inbound interface.
A file adapter service has been defined. Message protocol 'file content conversion' has been chosen for the file adapter service. Next the file format has to be defined in communiction channel settings.
Is it possible to define the input record structure in the file to be red itself?
The first line will list all column names. The data records will follow in line two up till end of file.
Regards
Klaus

Now I can add some more information to the facts.
In XI 2.0 the adapter engine was used to connect the integration engine to external systems. The adapter engine converted input file contents to a XML message. The structure of the records in the input file has to be defined. There was one option to read this structure from the first line of the file itself. This option was called 'fromFile'.
Now the current situation in XI 3.0 is that the integration engine reads the input file. Conversion of file contents is still available but the option to read the record structure from the input file doesn't exist anymore.
Does anybody know whether I am right and this functionality isn't available anymore or how to achieve the desired system function in XI 3.0.
Regards
Klaus

Event controll: How to stop a running while loop inside a event structure

Hello,
I have some problems with controlling a while loop inside a event structure (see attached VI).
I habe 3 buttons ("Start Measurement, Stop Measurement, Quit Program"). When a measurement is running, it should be possible to stop the measurement by clicking on "Stop Measurement", but this does not work.
Has anyone an idea?
Thanks a lot and best regards,
Michael
Message Edited by MichaGue_01 on 04-23-2010 04:37 AM
Solved!
Go to Solution.
Attachments:
Event_Controll.vi ‏27 KB

Hello,
Try not to use while loops inside a Event structure.
My approach is using two While loops (one will have only the Event structure).
I had to use to Flag buttons that make it a bit more complicated but i am sure somebody will come up with a better idea, or you might want to have a think about it yourself.
Have a look on the modified version on the attachment.
Once you are happy how it works then you can Hide the 2 flag buttons from the Front Pannel by going to Block diagram right-click the indicators and choose option "Hide Indicators/Controls"
I did it in LV 8.6 so i hope you can open it on your PC if not i can downgrade it.
If you have any problem let us know.
Regards
Dimitrios
Test Systems Computing Engineer
Cummins Turbo-Technologies
Attachments:
Event_Controll[1]_modified.vi ‏18 KB

How to Transition to a Specific Case from an Event Structure Trigger?

Can someone help me troubleshoot my program. I've attached my VI so you can follow along with what I am describing. So here is the scenario:
I have a program that consists of four test states, stop test, request test info, and end program (cluster of 7 booleans). Each test state sends a serial command to a DUT, receives ACK packet, opens relays which disconnects the serial connection and DUT will continuously test by itself. If the user wants the end the test early, they can hit the "Stop current test" which will close the relay reestablishing serial communication, wait 10 secs for device to enumerate on the PC, and then send the serial command to stop the test. From here, the user can request test information from the DUT by hitting the "Request info" button.
So my dilemma is when I try to implement a time limit for cases 2 - 4. For case "M1-Idle", the program works flawlessly since there is no time limit. The program will send the serial command, transitions to "Open Relay" case and switch back to the "Idle" state to wait for the "Stop" command. The user has to hit stop whenever to close the relay, request info and/or continue testing.
For case 2 through 4, there is max time limit of 3 hours. This is where I am having difficulty opening the relays and then entering the timer count down case structure to start the timer. Question is, if I am using the Event Structure to trigger on a user action event (i.e. user presses "Run M2-Normal" - Menu.M 2: Value Change) it sends the command and move on to "Open relay" to break the serial connection as intended. Since the next state of "open relay" is "Idle" how can I add case selector to select "M2 - Timer" instead of "Idle" given that it was based on user selection of "Run M2" event?
Is that even possible? I tried using the feedback node on the state enum but its coming from the case state and not the event state so it doesn't enter properly into the timer state. Any help or ideas is greatly appreciated. Thanks in advanced.
Main_Working_Copy.vi is the main portion of the program.
Best regards,
Henry
Attachments:
Main.zip ‏106 KB

Hi Ofek_zeevi,
Welcome to the Support Communities!
The article below explains how to gift a song in the iTunes Store.
Some songs are not available as an individual purchase.
iTunes 11 for Mac: Give music and video
http://support.apple.com/kb/PH12293
I hope this information helps ....
Have a great day!
- Judy

How to make my waveform from excel file perodic in labview graph

Hi guys,
Previously I've made a vi which integrates the excel file, to plot the graph values in labview using the values in the excel file to give the me a better flexibility to decide what waveform i want it to be. Can i know how to actually make the graph periodic, as in the waveform repeats, because currently it can just plot out the waveform accordingly to the values i inserted in the excel. I've attached my vi and aso my csv file together. Thanks guy.
Attachments:
12.csv ‏1 KB
graph.vi ‏18 KB

So do you want to read the same values over again?
If that is what you wish to achieve then use waveform chart as opposed to waveform graph. I editted your code slightly so that you can see the different.
I hope this helps!
Mehak D.
Attachments:
graph.vi ‏18 KB

How to make Vi file as input file in Event structure?

Similar Messages

Maybe you are looking for