How to place a motion data representation in labVIEW?

i am using motion assistant software and labVIEW to move a slider in X and Y axis. i just want to know how can i plot sort of a graph in LabVIEW to represent my motion data? for example, if X axis moves to point 100, my graph will automatically plot to that point too. so if the slider moves to X,Y (1000,2000), my data representation will also move to (1000,2000) in the graph in LabVIEW.
i would greatly appreciate it if someone could just help me here. Thanks

Hello Gurl,
Thank you for contacting National Instruments. Depending on how the system is returning positional information, there are motion VIs that can return the current position of axes. Assuming that you have NI-Motion installed, you can find these VIs in the block diagram by right-clicking and selecting Search. Type "Read Position", and a number of ".flx" type VIs should show up. Use these VIs to obtain the current position of each axis. You can build the points that are returned from each axis into arrays using for loops. Once you have arrays built for each axis, bundle the axes into a cluster, and then pass the cluster to an XY Graph. The cluster is necessary to pass multiple axes of information to an XY Graph.
Regards,
Mike T
National Instruments

Similar Messages

How to place pipes, pumps and valves in LabVIEW 8.5?

Hello,
I'm an Undergraduate student of Electrical Engineering and simulating the Lube Oil system for the gas turbine generator.
I need to know how I can place the pipes, pumps and valves in LabVIEW 8.5??
Also I need to know if a control symbol on front panel (e.g. a pipe) can be rotated/tilted or not??
Replies awaited.
Regards

There is a Multi-Segment Pipe control in LabVIEW, but it isn't on the palette. It's a boolean and the color indicates the state.
The attached VI contains one.
Note in addition to changing the size/shape with the grab-handles, you can right-click to add/remove segments.
Attachments:
Pipe.vi ‏5 KB

How to use ELMO motion control device with LABVIEW

Hi,
I am
new to LabVIEW withvery little controls
experience (just now graduated). I need to use LabVIEW, NI USB 6009( DAQ)
and a Harmonica servo drive from Elmo to control a voice coil. . What I
am looking for is some general guidance to get me started; point me in
the correct direction so I can get rolling. I will be using a RS-232
line between the Harmonica and the PC.
I have generated a sine waveform to the NI USB 6009 from LABVIEW. I have to send this signal through the ELMO Harmonica 5/60 N to control a voice coil. I have
been reading the Elmo SimpleIQ Software Manual and am lost Kindly help me out.
Regards,
Pawan
The software manual states using Interpreter Language or User
Programming Language. Both of the languages seem to resemble what I
remember of C++, sort of. The document explains "while" and "for"
loops, etc.; however, my understanding is that I should be able to use
LabVIEW to accomplish such tasks and then just ask LabVIEW to output a
command to the Bassoon to control my voice coil. My best guess is that
I use the "System Commands" to output commands to the Bassoon although
the software manual also mentions compiling code similar to that of
standard programming modes.
Please help me out.
Thanks

Continued here.
LabVIEW Champion . Do more with less code and in less time .

How to place one column under another column in obiee report?

Hi all,
I am new to obiee, so need some help from obiee experts. Can anyone tell me how to place one column data under another column in obiee report?
i need the report to be as below
category total_students Course_enrollment Test_attended pass_test
total N % N % N %
all students ##### ## ## ## ## ## ##
Ethnicity
Asian ###### ## ## ## ## ## ##
African American ###### ## ## ## ## ## ##
white ######
Filipino ######
Gender
Male ##### ## ## ## ## ## ##
Female ##### ## ## ## ## ## ##
and similarly for other columns
where ethnicity, gender are columns in the table and Course_enrollment, Test_attended, pass_test are calculated columns.
Please help me to create a report as above if anyone knows how to do it.
Edited by: Shailaja on Jul 19, 2010 12:23 AM

Two ideas I can think of:
1) Create multiple pivot tables and then display them one under the other
2) Create multiple measure columns such as "male_amt", "female_amt", "white_amt", "asian_amt", "black_amt", etc. for all the columns you need. Then you could simple stack them in a single pivot table.
Option #2 might give you the prettiest results - but also requires a lot more maintenance (for instance, if you reclassify ethnic groups, you'd have to go through the reports to add additional metric columns).
Hope this helps,
Scott

How to save the retrieved data in a subscreen...

Hi,
I understand that the subscreen has to be created in transaction se51. However, i dont have any idea how to use it and incorporate it in my main program.
Im trying to figure out how to place all the data retrieved in a subscreen where the user has an option to remove files that are not necessary.
For example:
The user enters a single transfer order, multiple transfer order, or a range of transfer orders. Retrieve transfer order number (TANUM), transfer order item (TAPOS), TO quantity (VSOLM), and Material Number (MATNR) from table LTAP where field tanum = transfer order. If no data is retrieved, an error message will prompt the user to enter a valid transfer order.(<-- I already coded this part)
***The data retrieved will be placed in a sub-screen where the user has an option to remove files not needed to be printed. (<--i havent started this one)
Kindly provide me a sample code or a step by step process. I would really appreacite your help.
Thank you very much.
Regards,
Tim
Message was edited by: Maan

Hi Tim,
first a warm welcome and congratulation for your first post.
Because this is the forum for Samples and Downloads it is not really clear what you are doing. Do you develop an ABAP Dynpro, a BSP or a Web Dynpro?
I think the chance of an answer is much bigger if you post your question in the ABAP/BSP or Web Dynpro Forum.
Hope that helps
Best regards
Renald

How to Create and export motion data from After effects CC to Flash CC

Hi there ,
Basically what I've got here is as follows.
I have a small character animation (about 100x100 px) - that is running inside a screen of 1280x720 px.
I want to hold the caracter in one position (so that I can get ridd off the useless alpha. i guess i will do that manually by keyframing)
and also to give a motion data to be used in Flash CC - to assemble the original animation.
Can anybody help me out with this?

Yeah, that's one of the reasons that we removed it: no one was using it. And it was terrible.
Here's more information:
http://forums.adobe.com/message/5555577
Of course, if you _do_ want this feature, it's relatively easy to save the project back to After Effects CS6 and then use After Effects CS6 to create an XFL file. Keep in mind that all Creative Cloud subscribers have access to CS6 versions, too.

I lost my iPhone device, how can I get my data back on another one without using an iCloud backup just back up on i Tunes, Please Help.

I lost my iPhone device, how can I get my data back on another one without using an iCloud backup just back up on i Tunes, Please Help.??

You can find the backup files and then copy them to a safe place if you are worrying about this.
iTunes places the backup files in these places:
Mac: ~/Library/Application Support/MobileSync/Backup/
The "~" represents your Home folder. If you don't see Library in your Home folder, hold Option and click the Go menu.
Windows Vista, Windows 7, and Windows 8: \Users\(username)\AppData\Roaming\Apple Computer\MobileSync\Backup\
To quickly access the AppData folder, click Start. In the search bar, type %appdata%, then press Return.
Windows XP: \Documents and Settings\(username)\Application Data\Apple Computer\MobileSync\Backup\
To quickly access the Application Data folder, click Start, then choose Run. In the search bar, type %appdata%, then click OK.

How do I get a date out of this: 14:35:42.0868394-08:00 ???

I am receiving an XML document from a person who generates it via a .Net page. This is supposed to be a date/time object. In his .Net code he uses the object just fine. I have asked that he translate it to something more standards like {ts '2012-03-01 15:59:45'} but he won't and said I should just figure it out... Nice, huh?
Does anyone have any idea how I can get a date out of this value:
14:35:42.0868394-08:00 ???
I know that the last part (-08:00) refers to Pacific Standard Time. I am pretty sure that the 14:35:42 represents 2:35:42 PM. If that is correct, the 0868394 must represent 3/1/2012 (the day I ran the report).
Please help.

HugoSchmidt wrote:
I am receiving an XML document from a person who generates it via a .Net page. This is supposed to be a date/time object. In his .Net code he uses the object just fine. I have asked that he translate it to something more standards like {ts '2012-03-01 15:59:45'} but he won't and said I should just figure it out... Nice, huh?
Does anyone have any idea how I can get a date out of this value:
14:35:42.0868394-08:00 ???
I know that the last part (-08:00) refers to Pacific Standard Time. I am pretty sure that the 14:35:42 represents 2:35:42 PM. If that is correct, the 0868394 must represent 3/1/2012 (the day I ran the report).
-08:00 may indeed refer to the time zone. However, if you're expecting the date-time, then he is shortchanging you. What he has sent you is just the time in hours, minutes and seconds, with the seconds expressed in 7 decimal places.
You could just ignore the decimal places, and extract the time as follows
<cfset datetime_string = "14:35:42.0868394-08:00">
<cfset the_time = listgetat(datetime_string, 1, ".")>
<cfoutput>#the_time#</cfoutput>

After a Lion clean install, how do I retrieve my data from external back-up? Following Apple advice for use of Migration Assistant did not work creating similar issues leading to clean install.

After a Lion clean install, how do I retrieve my data from external hard drive?
Following Apple advice I used Migration Assistant which crashed new system twice which is why I had to clean install Lion in the first place.
Is there a sure way of doing it?
I have only a few programs that I will have to install myself and that should not be a problem.
I just want my data, music and photos back where I can use them.

Time machine backups. I went to migration assistant a few hours ago and limited my selection to "users", no need for applications, settings and other files. Stuff started moving over at a fast pace but has now seemed to stall.
I will let it run overnight as there are lots of songs and photos as well as a few movies.
If that does not work, then I will go into TM and try restore. I have restored some things in the past such a mail files and it has worked well.
The Apple fellow at the store told me to go right into TM, he may have had a point. I'll get it eventually.

I backed up my ipod. I then updated it but all of my data is still gone. How do I get my data back??

I backed up my ipod. I then updated it but all of my data is still gone. How do I get my data back??

Were the app in your iTunes library? If not the app data in the backup has no place to go. Redownload the apps in your iTunes libaray
Downloading past purchases from the App Store, iBookstore, and iTunes Store
and then restore from backup.
iOS: How to back up and restore your content
Otherwise, try restoring from backup again.
If still problem that means the backup does not include the data.

I unfortunately just got my IPhone 4s stolen.I thought I had the find my iPhone enabled but I didn't because I cannot locate the phone when I sign in ICloud.How can I erase all data on the phone so the thief can't access my personal information.

I unfortunately just got my IPhone 4s stolen.I thought I had the find my iPhone enabled but I didn't because I cannot locate the phone when I sign in ICloud.I have a password on the phone but i'm not sure if I turned on the option where the phone resets if you incorrectly put the password more than ten time. I immediately called my phone company (Verizon) and reported the phone stolen.So I know whoever took the phone cannot place calls or use the phone. But can they still access my data on the phone if they manage to unlock the phone? If so how can I erase all data on the phone so the thief can't access my personal information? is there any other way other than Find my IPhone to wipe off the data on the phone? I really don't want my personal information such as pictures, text messages, notes and social networks profile available to a stranger!!? Help please!!!

Hello thewrongway,
I'm sorry to hear about your phone! I understand the need for an active device. You are able to activate an old device and process an insurance claim for your iPhone 4s within 60days from the incident date. Keep in mind if the old phone is not a smartphone and you currently have unlimited data that feature will fall off. If you have a tier data plan no changes will be made. Please let me know if you have any additional questions. Thank you.
TominqueBo
VZW Support
Follow us on Twitter at @VZWSupport

How can I set the data binding between Web Dynpro & Database table

Dear friend,
I am a beginner of Web Dynpro. I want to develop my simple project like these:
1. Create my own database table via Dictionary Project such as TAB_USER and have 3 fields: USER_ID, USER_NAME, USER_POSITION and I have already deployed & archived it.
2. Create my own Web Dynpro Project, and create the input fields as User ID, User name, User position and icon 'Save' on the selection screen and I have deployed it already.
For the process, I want to input data at the screen and save the data in the table, please give me the guide line like these:
1. How can I set the data binding between Web Dynpro and Database table ?
2. Are there any nescessary steps that I will concern for this case?
Sorry if my question is simple, I had try to find solution myself, but it not found
Thanks in advances,
SeMs

Hi,
You can write your own connection class for establishing the connection with DB.
Ex:
public class ConnectionClass {
static Connection con = null;
public static Connection getConnection() {
try{
Context ctx = new InitialContext();
DataSource ds = (DataSource) ctx.lookup("jdbc/TSPAGE");
con = ds.getConnection();
return con;
}catch(Exception e){
return null;
You can place the above class file in src folder and you can use this class in webdynpro.
You can have another UserInfo class for reading and writing the data into the DB .
Regards, Anilkumar
PS : Refer
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/webas/java/simple java bean generator for database.pdf
Message was edited by: Anilkumar Vippagunta

When and how to update the "saved data" in report ?

Hi,
The BO version is "BusinessObjects Enterprise 12.0"
The case is that, some reports are uploaded withe saved data. while viewing the reports, the reports return the old data.
How to view the update data while click the "View" in CMC/InfoView ?
I have tried to schedule it , then can see the update data in "View the latest instance".
Is there any approach to refresh/update the saved data in the report ?
Thanks and regards,
Forest
Edited by: Forest lin on Dec 5, 2008 12:12 PM

Hello Forest lin,
I recommend to post this query to the [BusinessObjects Enterprise Administration|BI Platform; forum.
This forum is dedicated to topics related to administration and configuration of BusinessObjects Enterprise, BusinessObjects Edge, and Crystal Reports Server.
It is monitored by qualified technicians and you will get a faster response there.
Also, all BOE Administration queries remain in one place and thus can be easily searched in one place.
Best regards,
Falk

How to place an image in database and how to retrieve and display it in the front end

how to place an image in database and how to retrieve and display it in the front end
and to place an image in database and retrieve the image from database using xml
please,help me out.

Create a table with a Long RAW Datatype column for storing the Image Column Data.
Create the form based on the table , which by defaults the column with LONG RAW atatype to a Image Item.
You can use Forms Built in function READ_IMAGE_FILE to read a Image file stored on the file system in to the image item.
A save on the form saves the image in the Image item in the long raw column.

How to insert values in table control & how to place listbox in table ctrl

Dear all,
            I have created table control in Module pool program. My requirement is first
               1)How to place list box in table control
               2)Based on listbox selection i have to enter values in table control row..
With Regards,
Baskaran

Hi Baskaran,
For displaing list box, use FM: VRM_SET_VALUES.
Code like that:
TYPE-POOLS: vrm.
DATA: name TYPE vrm_id,
list TYPE vrm_values,
value LIKE LINE OF list.
PARAMETERS: ps_parm(10) AS LISTBOX VISIBLE LENGTH 15.
Instead of parameter for module pool , you declare data:
AT SELECTION-SCREEN OUTPUT.
name = 'PS_PARM'.
value-key = '3500000002'.
value-text = '3500000002'.
APPEND value TO list.
value-key = '3500000003'.
value-text = '3500000003'.
APPEND value TO list.
name = 'PS_PARM'.
value-key = '3500000004'.
value-text = '3500000004'.
APPEND value TO list.
name = 'PS_PARM'.
value-key = '3000000007'.
value-text = '3000000007'.
APPEND value TO list.
CALL FUNCTION 'VRM_SET_VALUES'
    EXPORTING
      id     = name
      values = list.
make the necesary change for module pool.
Hope this can solve your problems.
Regards,
Tutun

How to place a motion data representation in labVIEW?

Similar Messages

Maybe you are looking for