How to render or output a multicamera project

I am thankful for the previous help and now I have the multicamera project almost done.  I used multicamera window and went through 1 hour of film shot from two cameras.  It went into sequence 002 and then I put video transitions between each clip. It plays fine in the project window.  I don't know what to do next.  I tried export - media and that brought up a window with a preview and output preview and choices of dvd. I left it on ntsc dvd and click export it put a 1 meg file on the computer, project file or something.  It takes about a second to do that. I tried rendering workspace and rendering time line and that takes way longer but results in 130 separate files on the hard drive.  I don't know what to do with them.  One time early when I was playing with this with a single video file I had adobe encoder come up, but I can't find that anywhere now.  I don't understand how to get this video with the transitions rendered out to an avi file.  Thanks for helping,  I have a book coming from Amazon on how to use this, not here yet.  I find the adobe pdf help file, not so helpful.  Doug

What version are you using Doug?
If CS4, you file>export>media and it opens up the dialog you mention.  Then choose the one you want.  This will in turn launch the Adobe Media Encoder which will actually do the rendering.  Note where the output directory is.  From there, you should be good to go.

Similar Messages

  • How to render faster when working on project

    how to render faster when working on project in motion 5? Working on a project gets very slow when a lot of elements are going such as 3D

    In the Render menu, top right of the Canvas pane, you can turn off all the render settings not in use, such as lighting, shadows, etc.  Also, set the resolution and quality in that menu down lower.
    When you're ready to export, you can re-set those settings to how you want it to export.

  • How do I share all angles of a multicam project versus a single stream

    I have a project in which I am trying to demonstrate the impact of diferent filters/settings across 4 cameras.  I have captured and syncronized all four cameras using an audio track.  So far no problem.  I however cannot determine how to export/share the the final project so that all four cameras are seen in a 2x2 setting, very similar to what is seen during the multicam editing process.  I only see how to produce a single stream which allows me to switch/cut between the various angles (if I were so inclined to do so..)
    Thank you in advance for the help.

    Hello Tom; 
    Thank you very much, and yes, I am using Multicam to sync the stream.  Your reply definitly moved the ball down the field.  However, while in the red zone, I have one final problem.
    With 4 streams overlayed in a multicam clip, when I attempt to crop or otherwise resize one of the 4 streams, I am not seeing the next stream below.  I suspect this is because I produced the stream as a multicam versus Compound Clip.  Here is a picture of what I am seeing:
    Assuming my hunch is correct, I am left with a dilema:  I need to have all four clips syncornized.  Multicam addressed this.  However, I now need to be able to transform/crop the individual clips into 4 concurrent views which I believe can only be accomplished via compound clip. 
    Any thoughts on how I can achieve my goals?
    Also always, think you in advance for the support.
    - Ed

  • How are you outputting your 24fps projects to tape?

    Hi There,
    I am just looking for any input on how everyone is laying down there 24fps projects to tape? We have found a method that seems to be working - but is very tedious and not perfect...
    Here is the lowdown:
    1080p23.98 ProRes HQ sequence -----> outputting to Kona LHe Card -----> To Sony DVW-A500 D-Beta Deck.
    At this point, we are getting the Kona card to add the pulldown because of the dramatic increase in quality over FCP - BUT because we are going from a NDF timecode to a DF format there are the obvious sync and drift issues.
    So here is what we did:
    - created a sequence with the exact same settings as our normal FCP output sequence (1080p23.98) and dropped in an hour of bars with TC reader.
    - Output this sequence to tape.
    - The use the deck to go to the all the in and out point timecodes we will need - ON THE DECK ITSELF. Then check the broadcast monitor, to see what the timecode on the bars reads and insert a marker in the timeline for our inpoint and outpoint.
    This way, although our output sequence looks a little funny in FCP (say for example, one minute or bars will actually look 2 frames short) by the time it goes to tape with the pull down inserted, it ends up the right length.
    Now, the problem we are having is we can only seem to get as close as being a half frame from perfect. Our 1 frame two beep will either enter a half frame early or a half frame late, depending on where it is located in FCP - up until now we have always just accepted this, but it can be frustrating because it makes inserting any changes in an episode not possible. This is the same regardless of whether the tape was pre-striped and episodes inserted OR Assembled to tape.
    If anyone has any alternates that are working better for them, it would be greatly appreciated!
    NOTE: Outputting a 29.97 NDF tape is NOT a valid option - because aside from commercials, this would never be accepted by a broadcaster.
    Thanks again.

    No such thing as a "half frame" in video. Audio, yes, video...no. Full frames only.
    This is what I used to do:
    http://lfhd.blogspot.com/2006/09/online-workflow-overview.html
    This is what I do now:
    http://lfhd.net/2008/10/22/timecode-calculator/
    Figure out what my NDF timing has to be to hit the proper DF timing when outputting. But if I had to meet Discovery/NatGeo specs of needing commercials to hit on 00 frames...then I wouldn't work in 23.98 NDF timelines...nor shooting formats.
    Shane

  • Multicam project: rendering timeline disabled multicams in viewer

    i am working on a multicam project and recently rendered my timeline, ever since i did that, i have been unable to view the multicams in the viewer while playing back in the timeline. if i go to a spot in the timeline and pause, i can see all cameras, but once i start playing, i only see the selected camera. i did a test with a new sequence, created a short multicam clip and was able to see all cameras in the viewer. then once i rendered the new test sequence, i could no longer see all cameras. i am making sure that i am selecting "open" instead of "sync off" from the top pulldown of the viewer. finally, i closed out fcp, deleted the newly created render file for my test sequence, reopened the project, of course i got a message that one render file was missing, pressed continue, played back the sequence, and once again i was able to see all cameras. so my question is, is this the fix? delete all of the render files for the project so that i can view all cameras, seems kinda strange this is happening....

    You could just duplicate the sequence and render that for client viewing, keeping your working version unrendered, until you're ready to render.
    Overall, it basically depends on your workflow and what you're doing. Mine has a pretty slim range of workflow steps, so I just duplicate the sequence when I'm ready to move to the next stage. This way I can always go back to an earlier version or stage of the process if needed.
    Also keeps me from filling up harddrive space with unnecessary rendering. I generally do my render once I've got a 'locked cut' in place (collapsed sequence w/color correction, filters, L3rds...etc), then I duplicate that sequence after rendering to add different show opens/closes for different final outputs. The duplicate retains the original render files, so I don't have to keep rendering each final sequence.
    K

  • How do I embed fonts into Captivate projects?

    This question came up in May 2006 but was never really
    answered. I'd like to know how to embed fonts into my Captivate
    projects so that the output looks the same on all computers. While
    the text animations are fine, the Text Caption fields are the ones
    that seem to have fonts that go walkies on other computers. I know
    you can embed fonts in PDFs. Why not in Captivate (unless I'm
    missing something in 2.0).

    First, a tip for the forums: If you use the URL tags, your
    post won't require horizontal scrolling - sorry, but I use Firefox
    and entering a long URL totally blows my ability to smoothly read
    the post ... you can manually add a text link by using the "L" tag
    as shown below (I've put spaces in to avoid this being turned into
    another text link)
    [ L = Your Text]
    http://www.yourdomain.com [ /
    L ]
    Back to your issue, Charinos. I'm glad you did find the URL,
    but that thread and your problem are not even in the same world.
    That thread deals with fonts in text-entry boxes (boxes for
    end-user text-entry), and you are talking about text-captions, an
    entirely different object.
    In fact, if you make changes and save those changes to a
    text-caption, then publish the project, the fonts in your text
    captions will remain stable and are not dependent on the fonts
    installed on the end-viewer's machine. The reason is that when the
    SWF is compiled, the text captions are converted to images and so
    long as the file is viewed as intended in the HTML document - at
    the proper size - the stretching you describe cannot take place.
    I'm not saying you are seeing things, but if my understandings of
    the Captivate machine are correct, what you are saying is happening
    cannot
    be happening. Something else is going on, like a failure to
    save changes, use of non-conforming text-caption boxes with a
    resultant loss of margins, or something.
    Sorry I'm not more help. I can't duplicate what you are
    seeing but I hope someone else can help you out - I may still be
    misunderstanding your issue.

  • How to change the output executable file name(a.prj:(output)--- b.exe)

    LabWindows / CVI： how to change the output executable file name
                For example, I have an A project a.prj, I do not want to compile the output file is a.exe, but b.exe.
    I will try to save as a.prj b.prj, a.cws save as b.cws
    eg:a.prj  ---->(output)--->b.exe
    Solved!
    Go to Solution.

    You can go to Build >> Target Settings menu item, select Release (or Release 64) in the Configuration filed and set the name of the executable to create in Application FIle field, withouyt need to change the prj or cws filename.
    See the complete description of available options here.
    Proud to use LW/CVI from 3.1 on.
    My contributions to the Developer Zone Community
    If I have helped you, why not giving me a kudos?

  • Sun ONE Studio 4 aka Forte: How to set the output path for classes ?

    Help !
    Beginner's question:
    Sun ONE Studio 4 aka Forte:
    How to set the output path for classes ?
    As default, the class files are created in the same directory as the
    sources.
    In opposite, both JBuilder and Together support that there is a tree
    with the sources and another tree with the classes.
    The first answer I got was "not possible with Forte, but just if you write your own "ANT Build script" !
    a) Please point me to a ready-to-use ANT script for this purpose, if such is available
    b) Is using ANT instead of the MAKE as comfortable ? Besides the separation of sourcecode and classes, I would like to keep everything else to be the same, i.e. I don�t want to edit the ANT file if I enlarge the project by directories or files.
    Tia
    Sincerely
    Rolf

    You can set S1S's options to place newly created .class files in a specific location.
    Identify the compiler that is being used - Open the S1S's Tools/Options window, expand Editing and select Java Sources. Note the Default Compiler value. (If it's one if the Ant options, you use Ant to specify this option, not S1S.)
    Open the S1S's Tools/Options window, expand Building/Compiler Types and select the appropriate compiler.
    The Properties tab of the compiler has the property Target, which sets the filesystem where the compiler output is directed. If you choose <not set>, the .class files are written to their source directory.
    When you set the Target, your change affects all classes that use this compiler.
    Very few options can't be set in S1S; the challenge is finding out where they're set!

  • Need to render everytime I re-open project in PP3

    My problem:
    On a particular project, I need to re-render everything everytime I re-open project even after I have saved and closed project.
    I also experience SERIOUS ERROR crashes or simply PP3 freezes while trying to render whole timeline, I need to render in chunks.
    The project file is a single timeline 2:45 minutes long with only the clip on timeline in project; it's CFHD low res clips (not corrupted) and there's quite a lot of CF cross-fades in timeline (it's a trailer) with about 5-6 clip color corrected that need to be rendered.
    My specs are:
    PP3 + AspectHD v5.2 build 105
    dualmonitors with Ultramon 2.6
    AMD ATHLON x2 4600+
    4 GB SDRAM2 733 Mghz (dual channels)
    MATROX APVe
    ASUS SLI-DELUXE
    Sound Blaster X-FI

    Hello Frederic,
    I am having the same issue. I am also using AspectHD v5.2. The timeline which I am having this issue has many effects and also has some imported Photoshop files. Another aspect of this is that when I try and play the timeline the play-head jumps to the end of the timeline. If I render the clip it plays fine. Except when I exit Premiere and then open it again the renders are lost and I'm back at square #1. I have been struggling with this since November and am not sure how to fix it. I know you were hoping for an answer (as am I) but thought I would just chime in to let you know someone else is also having this issue --- for what it's worth...

  • Flex Build Path : How to really customize output folder ?

    Hi all,
    I am using this kind of project structure :
    D:\project\src\ : the flex project sources
    D:\project\src\classes\ : the mxml / AS classes
    D:\project\bin\ : the swf output
    My main application is in this path :
    D:\project\src\classes\projectPackage\Main.mxml.
    I configured my Flex Build Path (in the flex project
    properties) this way :
    - Main source folder :
    classes
    - Output folder :
    D:\project\bin
    Unfortunately, the output files are created in these paths :
    D:\project\bin\projectPackage\Main.swf
    D:\project\bin\projectPackage\Main-debug.swf
    D:\project\bin\projectPackage\Main-profile.swf
    Whereas I wanted :
    D:\project\bin\Main.swf
    D:\project\bin\Main-debug.swf
    D:\project\bin\Main-profile.swf
    Would you know if it is possible to configure the real output
    folder somewhere ?
    Thank you all
    Cheers
    Philippe

    Hi levancho,
    Thanks for your answer.
    You probably meant to use
    src\classes\projectPackage as the Main source folder.
    This is working this way. However, there are some little
    problems :
    I have this warning : "
    Source path entry, '
    D:\project\src\classes', is a subdirectory of source path
    entry, '
    D:\project\src\classes\projectPackage'." which is
    strange because it is the second path which is a subdirectory of
    the first.
    There are conflicts when the compiler
    tries to resolve the classes within the
    src\classes\projectPackage directory. For instance, for a
    class clalled Application located in
    src\classes\projectPackage\Application.as, it doesn't know
    how to make a difference between Application and
    projectPackage.Application.
    Solution : move classes from
    projectPackage to some sub packages.
    Anyway, if it may not be the perfect solution, it just works,
    so thank you very much :)
    Regards,
    Philippe

  • How do I move a Premier Elements Project to a new computer?

    I want to move a Premier Elements Project to a different machine with more efficient RAM and SSDs. How do I move a Premier Elements Project to a new computer?

    Welcome to the Premiere Elements Forum.
    I constantly migrate my Premiere Projects between my laptop, and my workstation, but I set those Projects up, initially, with that in mind - which is different than having a Project set up on one computer, and then moving it to another. For my setup (remember, this is initially, when I start a Project), see these two articles:
    Setting Up Project Folders & Sub-folders
    Using External HDD's for Video Editing
    For existing Projects, there are a couple of ways to address this. The method that you use, might depend on how you plan on moving the Project.
    If you have an external HDD, and plan to use that to do the move, see the "Using External HDD's" article above, as it talks about drive letters in the OS. Getting that correct first, can save a lot of work later.
    Then, one can use the Project Archiver to Copy the Project, and necessary files to that external. When one has done that, I strongly suggest that they test that "archived Project," to make sure that the Archiver has gathered everything necessary. The success of that process can depend on how one has set up their folders and sub-folders, and where their Assets (the material that has been Imported into the Project) is located. That is why I always urge one to test everything first. Then, just plug that external HDD into the new computer. At that point, they will have two options: edit to/from the external, or Copy everything to the new computer. For the former, see that "Using External HDD's" article, as there can be some limitations, such as both HDD speed and connection speed, that can impact how well things work.
    Next, one could just Copy (over a a wired, or wireless network, or via an external HDD), the Project file (PREL), all Assets, and most of the Scratch Disk folders, to the new computer.
    Note: there are files in the Media Cache, such as CFA's and PEK's for the Conformed Audio, that do not have to be Copied/Moved, as PrE will rebuild those (give the program time to do so, and do not edit the Project, until they ARE rebuilt). Same for the Render Files, as if those are needed, one can easily hit Enter/Return, to Render the Timeline, or part of it, again.
    Keep the folder structures.
    If one gets the "Where is file _____ ?" message, this ARTICLE will be helpful.
    Note that the PREL (Project) file is really an XML database. It contains NO MEDIA, but only absolute links to where that media was Imported from. See this ARTICLE for more background.
    Good luck, and if you have any questions, or something above was not clear, please ask, before you make the move, as the answers might save you some time, and extra work.
    Hunt

  • How to render click-able URL and bookmark links

    Hello,
    I would appreciate if anyone helps me to answer below questions
    We have Oracle Business Intelligence 11.1.1.6.8
    How to render a click-able URL in the report output?
    How to render the bookmark links (left side) in a PDF?
    Can we create group-level formula column?
    Thank you

    Hi Alan,
    I know this is an old post but I think it might help me.  You reference a tutorial to add an "invisible button".  I've been given a flash banner that I think has an invisible button but I don't know how to use it in my web page.  Clicking the banner opens a new window with a page "Undefined".  Maybe if I understand how to create the button I'll figure out what the author did and how I'm supposed to use it.  Can you give me the link to your tutorial?
    Thanks.
    Steve

  • How to render properly to Blackberry 8800

    I've completed the ADF Mobile tutorial which works fine on the Blackberry emulator/simulator. Table rows appear in a table object and look great visually. However, when I run it from the actual Blackberry 8800 the rows appear unformatted without the table object. How do I properly render the output to the 8800 to visually appear like it does in the emulator?
    thanks
    John

    Hi, John, did you use the 8800 simulator when you developed the application as well? Different BlackBerry devices behaves a little bit differently - we would render plain HTML content to BlackBerry 4.5 and below devices because its JS engine is poor. 8800 is one such device. If you are using a simulator running 4.6 and above, then it would look different from how it would appear on the 8800 device.
    Also, on 8800, you would need to ensure a few options are checked - for example one option was to "support hTML tables". You would need to check this option, or the table may not display correctly.
    If you have additional issues, please just email me directly and I can help at [email protected]
    Thanks,
    Joe Huang

  • How to find next number range for project definition in tcode CJ20N

    Hai Experts,
          Please help me 'How to find next number range for project definition in tcode "CJ20N". I was trying in function module NUMBER_GET_NEXT. Is it right function module? If its right what input i need to give for this tcode and for the field project definition?
    Note: I searched in forum before posting, but couldn't find the solution.
    Thanks
    Regards,
    Prabu S.

    Hi,
    For project defination internal number is assigned by system.
    When you saves's project then system allocate one number to project defination, you can view it,
    SE11 >>> table  PROJ >> Click on contents >>> execute,
    here you will get your project defination & number is assigned to project defination.
    kapil

  • How Can I Run A SQLJ Normal Project In SAP NWDS

    I have a question about SQLJ in SAP NWDS.
    1.I created a java dictionary project,and then create the table , then depoly it.it's ok.
    2.I created a java normal project including the above java dictionary project.
    3.I used the SQLJ tech in the java normal project,exporting the opensqllib.jar,sqljapi.jar,sqljc.jar,sqljimpl.jar.
    4.I coded the normal project,and export the project .jar,everything is ok.
    <b>5.But when i runed the project in NWDS,the error appeared:java.lang.NoClassDefFoundError: com/sap/sql/log/OpenSQLException
         at com.ezkj.deom.sqlj.MainApp.main(MainApp.java:21)
    Exception in thread "main"</b>
    How Can I Run A SQLJ Normal Project In SAP NWDS?
    PLS Help me and don't let me alone!

    Tony,
    Why not try to import your SQLJ project in SAP NWDS. Add all the jars mentioned to the project path both for compile time as well as runtime. Now try running he project. Once you are able to bypass java.lang.NoClassDefFoundError, you will get other errors related to SQL statements. These Oracle SQL statements needs to be converted to OpenSQL format.
    Chill out!!!
    Sukanta Rudra
    Note: If helpful, plz donate some points.

Maybe you are looking for