How to setup Express next to fixed network (for audio only use)

For reasons I shall not explain here I want to keep my existing fixed netwerk (which is connected to my DSL cable modem) and install my new Airport Express on the same computer. I will only use the Airport in this configuration to connect iTunes to my stereo. Can anyone help me setup the netwerk configurations?
The existing DSL cable modem has DHCP capabilities, which I use for dynamic IP configuration on the fixed netwerk. My cable modem is 192.168.1.10 and my computer normally 192.168.1.11 (subnetmask 255.255.255.0). I sometimes hook up a laptop which becomes 192.168.1.12.
How should I configure the Airport Express itself (using the Airport configuration assitant or Airport Admin Utility) and how should I configure the wireless network?
BTW, the Express does work fine when connected directly to the DSL cable modem (with the fixed network disabled). However, the cable modem is far from my stereo.

I struggled with this for what seemed like days. Reading posts, seeing if anyone had an answer. Then I logged onto my router and found that the firmware was out of date. I updated the firmware, went through all the recnfituration and used the same security key that I had before and after reboot/reboot of the router it connected to the AirPort Express, now over 12 hours later it has stayed connected, streams music flawlessly. You might wantt to check this out and seei f it will work for you.

Similar Messages

Can we setup a 13 period fiscal year for 2010 only, using the same variant

We currently have a fiscal year running from October. We have been taken over by a new comany who want our fiscal year to run from November. It has been decided that year 2010 will contain 13 periods.
Can someone help with how to set this up in OB29.
The current settings are for 12 normal periods and 4 special periods. Therefore it will not allow 13 periods to be setup in 2010. However, if I change the number of normal periods in the variant to 13 then there is a message saying that there are gaps in the other fiscal years which are not 2010.
What is the correct way to deal with the extra month? We are currently in 2010 which started in October and we don't want FY 2011 to start until November.
Thank you
Karen

Thank you for your reply, but the problem is that we want to add a 13th period.
The setup we have is as below.
1     29     4     0
2     26     5     0
3     26     6     0
4     30     7     0
5     28     8     0
6     25     9     0
7     30     10     0
8     27     11     0
9     30     12     0
10     29     13     0
11     27     1     +1
12     24     2     +1
12     31     3     +1
This is working fine to find October as period 13 when we use function DATE_TO_PERIOD_CONVERT, but there is an error in the setup saying 'Only define periods until 12'. When we try to run function LAST_DAY_IN_PERIOD_GET this crashes saying fiscal year variant not found for 2010.
There is a setting in the fiscal year variant which says
Calendar yr     2010 No.posting periods   12   No.special periods 4
For 2010 only we want this to be 13 periods. Is this possible?
Thank you
Karen

I currently have a D-Link DI-604 broadband router with windows computers. How can I add wifi to the network for use with ipad? Can I use AirPort Express?

I currently have a D-Link DI-604 broadband router with windows computers. How can I add wifi to the network for use with ipad? Can I use AirPort Express?

Yes. You can directly connect an 802.11n AirPort Express Base Station (AXn) using an Ethernet cable. The AXn would then just need to be configured as a bridge to allow the D-Link to continue to provide both NAT & DHCP services for all network clients connected to either router.
In this configuration, the AXn would broadcast a wireless network for your wireless network clients to connect to.

I am trying to install a second airport express to extend my network. When I use the aiport utility it does not see the second airport express.

I am trying to install a second airport express to extend my network. When I use the aiport utility it does not see the second airport express.

Suggest that you perform a Factory Default Reset as follows:
Pull the Express from power
Wait a few moments
Hold in the reset button and keep holding it an additonal 8-10 seconds while you plug the Express back in to power
Release the reset button and allow 40-45 seconds for the Express to restart
Apple's instructions to do what you want are here:
It will often help to temporarily connect an Ethernet cable from your Mac to the AirPort Express for the setup. Once the Express is configured, you can disconnect the Ethernet cable and move the Express to the desired location.
http://support.apple.com/kb/HT4259
Although an AirPort Extreme is shown as the extending device in the example, the setup for an AirPort Express is exactly the same

How can I block all other mail account just to only use the exchange mailbox of our company? This is to prevent the user to setup his on company iPhone.

How can I block all other mail account just to only use the exchange mailbox of our company? This is to prevent the user to setup his on company iPhone.

I don't know if I'm asking this all in a way that can be understood? Thanks ED3K, however that part I do understand (in the link you provided!)
What I need to know is "how" I can separate or rather create another Apple ID for my son-who is currently using "my Apple ID?" If there is a way to let him keep "all" his info on his phone (eg-contacts, music, app's, etc.) without doing a "reset?') Somehow I need to go into his phone's setting-create a new Apple ID and possibly a new password so he can still use our combined iCloud & Itunes account?
Also then letting me take back my Apple ID & password, but again allowing us (my son and I) to use the same iCloud & Itunes account? Does that make more sense??? I'm sincerely trying to get this cleared up once and for all----just need guidance from someone who has a true understanding of the whole Apple iCloud/Itunes system!
Thanks again for "anyone" that can help me!!!

How do i find a wi-fi network for my iphone

how do i find a wi-fi network for my iphone? Message keeps coming up "incorrect wi-fi password (do not know this password) Enter the password for "R7443"?
Seems to me the wi-fi is working as i can get on internet and get email - but i have no idea what password they are looking for.

Where are you looking for a wi-fi network for your iPhone? Home , office, friends?
The owner of wi-fi R7443 has the password. Ask them for it if you know them. If you don't know them or know who owns wi-fi R7443 then you have no reason to use it.
Most people have their own wi-fi network at their home and use it for their laptops and phones.

How do I ask photoshop elements to search for and only add pictures on my computer?

How do I ask photoshop elements to search for and only add pictures on my computer?

vbond0071 a écrit:
Please tell me its a simple fix???
[email protected]
My suggestion:
Read the help file carefully:
http://helpx.adobe.com/elements-organizer/using/workspaces.html
Now have a look at the the organizer display layout. Just over the main display panel where thumbnails are shown, there is a drop-down menu to choose the sort order. I assume you are on a recent version of Elements? If you are on PSE12 or 13 you can choose the chronological order (ascending or descending), the filename order, or the import batch. Additionally, if you are viewing an album you can have a manual custom sort.
My other advice is that before you use the organizer, you take the time to read this help file carefully:
Elements Organizer Help | Creating and editing catalogs
The organizer is a very power tool if you understand what it can do and if you don't have misconceptions about how it works. It's a powerful toolset based on catalogs. It can handle and manage folders and files, but that's not its main purpose. Its ability to manage the information included in the exif metadata of your files and the important information you enter with categories, keywords, captions, notes, ratings or the way you include pictures in albums, creations, stacks or version sets is very powerful.

How to specify different horizontal restore & collapse icon for af|panelSplitter using Skinning based on Style class or position?

Hello,
I am trying to provide different horizontal restore & collapse icon for af|panelSplitter using Skinning based on Style class or position. I have 2 af:panelSplitter with orientation="horizontal" - One with positionedFromEnd="true" one with positionedFromEnd="false". I want to specify the horizontal collapse and restore icon using Skinning. I want specify different icons based on positionedFromEnd. When I specify icons they are appearing for both splitters. I gave 2 different styleClass to these splitter but it is not taking them in account,
JSPX Page -
<af:panelSplitter orientation="horizontal" splitterPosition="196" positionedFromEnd="false" id="pnlSplitterLeft" collapsed="false" styleClass="panelSplitterLeftClass">
<f:facet name="first">

</f:facet>
<f:facet name="second">
<af:panelSplitter orientation="horizontal" splitterPosition="196" positionedFromEnd="true" id="pnlSplitterRight" collapsed="false" styleClass="panelSplitterRighClass">
<f:facet name="first">

</f:facet>
<f:facet name="second">

</f:facet>
</af:panelSplitter>
</f:facet>
</af:panelSplitter>
CSS Skinn
af|panelSplitter::horizontal-restore-icon {
    width: 10px;
    height: 55px ;
    content : url("/skins/AppSkin/Left_Open.gif");
af|panelSplitter::horizontal-collapse-icon {
    width: 10px;
    height: 55px ;
    content : url("/skins/AppSkin/Left_Close.gif");
af|panelSplitter.panelSplitterLeftClass::horizontal-restore-icon {
    width: 10px;
    height: 55px ;
    content : url("/skins/AppSkin/Left_Open.gif");
af|panelSplitter.panelSplitterLeftClass::horizontal-collapse-icon {
    width: 10px;
    height: 55px ;
    content : url("/skins/AppSkin/Left_Close.gif");
af|panelSplitter.panelSplitterRighClass::horizontal-restore-icon {
    width: 10px;
    height: 55px ;
    content : url("/skins/AppSkin/Right_Open.gif");
af|panelSplitter.panelSplitterRighClass::horizontal-collapse-icon {
    width: 10px;
    height: 55px ;
    content : url("/skins/AppSkin/Right_Close.gif");
It is always showing Left_Open.gif and Left_Close.gif for both splitters. But I want different image.
How to specify different horizontal restore & collapse icon for af|panelSplitter using Skinning based on Style class or position?
- Sujay

CSS attribute selectors are what you are talking about, but binding the selector with EL is a more-common approach. Using selectors like this require you to ensure browser support.
af|panelSplitter.panelSplitterRighClass::horizontal-collapse-icon [positionedFromEnd=true]

How can we make the ms-word data as read-only using java code?

How can we make the ms-word data as read-only using java code?

MVSK wrote:
By using java code i opened a file in ms-word. But the data i want to display as read-only. that means should not change it.I don't think you can do that. Display pdf documents instead.

How do I uninstall ios6 from my ipod? I only use the ipod for music.

How do I uninstall ios6 from my ipod. I only use the ipod for music.

Downgrading the iOS is not supported by Apple.
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Unsync all music and resync
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

How to setup once an Airport home network and keep it alive?

Hello!
I have the following hardware setup:
1 - A Macmini 2009, Ethernet wired to my router which allows the connection to the internet;
2 - An HP Deskjet printer, USB connected to the Macmini;
3 - My wife's laptop PC, WiFi connected to my Mac.
My Macmini handles the internet connection the traditionnal way (Ethernet and PPoE) and has a static IP on it.
(Why a Static IP? Because I run my own Webserver.)
I set up a WiFi Home Network in order to allow my wife sharing both my Internet Connection and the Printer Connection.
Everything run well: fast and smooth. The PC has Internet and Printer access.
Problem is:
After each restart, I must re-create the Airport home network.
System Preferences-->Airport doesn't memorize the name, parameters and credentials of this network.
How can I fix this?
Many thanks in advance for your replies!
Best regards
Gerry

If your router is wireless, you should probably use the laptop to configure it to take care of the network (i.e. have the router distribute the IP addresses). Then you can connect your computer to it via the LAN port on the router. Otherwise, you would have to set up your computer to "share its Internet connection" (via Preferences/Sharing or Preferences/Network not sure). I don't think you need to create a network for this.

How do I set up multiple Airport Expresses to connect over ethernet for Airtunes only?

I am trying to set up an Airtunes network using an Airport Extreme and three Airport Expresses connected together via ethernet (CAT5 cable). At each Airport Express there will be a speaker setup. I don't need/want internet connectivity on the network, but not sure if it is required for setup or not. I have made this work over wifi, using the Expresses to extend the network, but struggling to get this to work over ethernet.
I would be verry grateful of a step-by-step method to setting this up! I am also looking to set up 6 airport expresses to do the same thing in another location.
Thanks in advance!

Thanks for the info.
I assume that the AirPort Extreme is setup and working at this point.
Work with one AirPort Express at a time to get them all configured, and then you can locate them where they will be needed.
AirPort Setup will configure the Express devices to "extend a wireless network" using Ethernet, so they will be broadcasting the same wireless signal as the AirPort Extreme and provide more wireless signal coverage as well.
I have yet to meet the first person who thought that they had too much wireless coverage, but you would have the option to turn off the wireless on the Express if you wanted. Most users like having extended wireless for their devices.
Temporarily, move an Express close to the AirPort Extreme
Connect a spare Ethernet cable from one of the LAN <-> ports on the Extreme to the WAN "O" port on the Express
Power up the Express for a few minutes
Hold in the reset button on the back of the Express for 10 seconds and release. Allow a full minute for the Express to restart to a slow, blinking amber light.
Click the Airport icon at the top of the Mac's screen and wait a few seconds for AirPort Express to appear just under the listing of New AirPort Base Station
Click directly on the AirPort Express
AirPort Setup will open up automatically and take a minute to analyze the network, then announce that the Express will be configured to extend the AirPort Extreme network.
Enter a device name that you want to use....example.....Express1.....and click Next
AirPort Setup will configure everything for you. Notice that the message will say that the Express is being set up to extend using Ethernet. When you see the message of setup complete, click Done.
Now you can move the Express to the remote location where it is needed, hook it up to the Ethernet connection there, power up the Express and set up AirTunes on the device.
AirTunes is enabled by default, to other than make the speaker connection, you won't have much to do on that.
Set up other Express devices the same way, except assign a different name to each device....example....Express2, Express3, etc.....to keep things organized.

How to setup PS Elements as default editor for LR4?

Hi all,
I have both PS5 and Elements 10 installed on my computer. Lightroom 4 selected automatically PS5 as my default editor. I am planning to switch completely to Elements 10, so I would prefer to have this program as my default editor. Unfortunately I do not see how to do this. Lightroom only allows me to setup additional editor and this option I am already using for Topaz Fusion Express. So my goal is to replace PS5 with Elements 10 as primary (default) editor. How to achieve this?

the default editor is set by lightroom.
When Photoshop Lightroom starts, it checks to see if Photoshop is installed. If it can't find Photoshop, it checks to see if Photoshop Elements is installed. If it can't find either, Photoshop Lightroom disables the Edit In Photoshop command. The Additional External Editor command is not affected.
If you uninstalled Photoshop CS4 after installing Photoshop CS5, some of the data required to Edit In Photoshop could have been removed. Reinstalling Photoshop CS5 fixes this issue.
On Windows, Photoshop Lightroom checks for the Photoshop.exe or PhotoshopElementsEditor.exe keys in the HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\App Paths\ directory of the registry. These keys provide the file path to the applications.
On Mac OS, Photoshop Lightroom checks for the com.adobe.Photoshop.plist or com.adobe.Photoshop.Elements.plist files in the user's preferences folder. These files provide the file path to the applications, as well as other OS-related information about the applications. The plist files on Mac OS are created the first time applications are started. The files are also created any time the application is started and the files are not present.
however you can have as many editors as you want as presets.
thought... only the two "primary" have a keyboard shortcut.
Lightroom -> Preferences -> External Editing
http://i.imgur.com/N2s9b.jpg

How to setup a Seamless Transaction Gateway with PayPal (Australia Only)

I've been working with the team at PayPal to allow BC Partners to set up a cost effective way to setup a Seamless Transaction Shopping Cart Process on their BC eCommerce website without the need for a 3rd Party Merchant Provider like eWay or Secure Pay or their bank. This is designed for entry level businesses who want to control their setup costs and keep all funds in one place (PayPal).
Currently BC doesn't support Paypal's Payments Pro plan in Australia so you are limited with either a non-seamless payment process or using a 3rd Party Merchant provider with can be costly.
Without going into too much detail, the setup on PayPal's side is a mixture of a couple of plans, and is a little complicated however through our discussions we come to an arrangement of any additional fee's associated with the setup being waived since this is more so of a technical workaround than anything else.
Basically PayPal is the merchant provider, and the customer doesn't leave your website when making a purchase through the Shopping Cart. The setup is only $25/month plus transaction fees of between 1.1 to 2.4% + 30 cents depending on the number of payments (this is just an initial guide and confirmed on your discussion with the PayPal).
Because the setup involves quite a few steps and departments I've arranged a contact that will fast track this process and is familiar with this unique setup.
How to setup PayPal for a Seamless Transaction Process
Sign up for PayPal Business account Timeframe: <20 minutes
Email Peter [email protected] or phone (02) 8288 0333. CC me [email protected] or mention my name so he can correctly setup the process and apply the discounted pricing.
Prepare for the Verification process for the PayPal account (Proof of ID, Proof of Address, Business documents etc).
Wait for Account Verification. You will be informed to setup both PayFlow Pro* and Website Payments Pro (*the PayFlow payment will be waived as mentioned previously). Timeframe: up to 5 business days depending on swift supply of required documentation.
Wait for your Billing Agreement for Website Payments Pro once application has been approved. Sometimes they will receive a phone call to verify details of the application. Timeframe: Up to 72 hours
Login into your PayPal account to accept the Billing Agreement.
Notify Peter once the Billing Agreement has been accepted so your PayFlow Pro can be linked to your Website Payments Pro
Login into your Business Catalyst Website and navigate e-Commerce > Payment Gateways
Select PayPal PayFlow Payment Gateway (..,AU, ..)
Enter your Username, PayPal Password, and add VSA as the Partner
Setting up PayPal Payments
If you also want to make payments via PayPal (ie, with the customers Pay Pal account) you can continue with setting up the PayPal Website Standard secure with your PayPal Customer ID and your PDT Token which you'll need to setup in your PayPal Account.
If you have any questions give me or Peter an email. I'll continue to update this document as I go.
Please note this setup is current for Australian Pay Pal Customers only. This process does not support re-occurring billing.

Dennis, sounds like you are having issues connecting to your network. Here is what we are going to do.
On your first question, and second question for that matter, I would suggest using a WPA password. Our printers doe not associate with the other types as well as WPA. You should be able to do that, though I have not personally set up a router that way to have experience in how it will react with the networked devices. As for the issues you are having, once the settings are all in the correct order I am going to suggest we connect the printer to the network through the computer.
What you will do is install the printer using a USB connection, then re-run the setup software. Here there should be an option for USB to Wireless. This will be the easiest way to be sure that all the settings are correctly transferred over.
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=303770
You can find the software in the link above.
Let me know if this helps!

How do I connect Airport Extreme and Time Capsule to my new iMac so that AE is used for network and TC only used for Time Machine backup?

I didn't realize that Time Capsule will only support the print function of a wireless multifunction printer. So I want to use Extreme for my network to have full use of my printer and use TC as the Time machine backup only. How to I make the connections?

Thanks for your response and this is getting complicated but I just purchased a new iMac as well as the Airport TC. I've had the Airport Extreme for a year or so. The Airport Extreme worked perfectly with my old iMac wirelessly and I had all functions of my printer with no problems. I was expecting the same with the TC. But the instruction that came with TC say to connect the printer to the TC via USB...which I did. And the print function worked perfectly but nothing else. In researching I discovered that when wired that way the TC only supports the print function...not scan or fax or anything else. I tried going wireless since my AE worked perfectly via wireless but I got no printer functions at all that way. But I'm wondering also if I tried that during a time I was having other issues...I had to delete and re-add my printer which solved some other problems. I may try that again...and see if I can get all print functions with just the TC connected
As far as connecting both your AirPort Extreme and Time Capsule on your network, we're not clear on exactly how you want to do this. Will the AirPort Extreme connect to your modem using an Ethernet cable and the Time Capsule connect to the AirPort Extreme using an Ethernet cable?.......or......do you want the Time Capsule to connect to the network using wireless?
Well... first of all I would like not to have to use the AE at all...I would prefer using just my TC for network, all print functions and Time Machine backup if that's possible. My printer will not accept Ethernet connections (Canon MX512).
After failing at getting this to work, I decided I would try to use my AE for net and print functions and just use my TC for Time Machine backup. I tried several different connection configurations with no success until finally I connected cable modem to my AE via Ethernet and went wireless with the AE and printer. but connected the AE to the TC via Ethernet and amazingly everything worked like a charm (for a while) and I was patting myself on the back for being so smart. But now I find that the connection only lasts for a short time. If I leave it for a while the TC goes invisible...or at least I see a message saying the Ethernet is unplugged...but it is not... and I lose internet connection even though I have a green light on my AE. So now I'm at a loss. I don't know why I keep losing network signal and why my system thinks the Ethernet is unplugged.
So... after all this...I figured I wasn't so smart after all and I must have things wired incorrectly.
So... it sounds like you are saying I should go back and try again to get my new TC to work as I want it to via wireless instead of connecting via USB...is that correct? Could you tell me exactly how I should wire my equipment from cable modem to AE and/or TC to achieve net capability, full functions of my printer and Time Machine backup...
Thanks...

How to setup Express next to fixed network (for audio only use)

Similar Messages

Maybe you are looking for