How to transmit multiple messages over CAN

Hi All,
How to transmit multiple messages over CAN ? With all three messages i want to send the system time & date also.
How can i get the timestamp in DBL format (Since the timestamp in the input of ncWriteNetMult.vi is a DBL). If possible kindly share the code in Labview 7.1 also.
Thanks in advance.
J

The NI-CAN driver brings examples for nearly every use case. Driver version 2.4 or later has the Write multiple function to write multiple frames at ones.
There is an example available for LabVIEW, CVI and VC/VBasic called CAN Transmit multiple.
Also check the attached VI and the Can manual: http://www.ni.com/pdf/manuals/370289m.pdf
What do you mean by converting Timestamp to DBL? Timestamp contains all date and time information. You can convert it into string format as shown below and then use the relevant data from it by string operations.
Hope this solves your problem.
Shreyas Hebbare
Shreyas Technologies
India
Attachments:
Transmit Multipe Objects at Different Rates_LV80.vi ‏36 KB

Similar Messages

Program to Transmit multiple messages over J1939

Hello Every one,
Can any one please post the program to transmit multiple messages over J1939 using USB 8473 device. I was looking under Ni examples but it is showing only to send the frame data but not the scaled data,I want to trasmit the Scaled data information and Iam also using Extended arbitration Id's in my *.dbc file.
Thank you,

Aside from the issues with the USB device and use of the Channel API, as far as I know, the only examples provided for J1939 here are based on the frame API, which precludes you from using the channel API with a CAN database on the same port. If you migrate to non-USB based CAN hardware (which I would recommend if within your budget), DMC developed a set of J1939 protocol CAN drivers for LabVIEW which are based on the NI-CAN channel API provided by National Instruments (NI). The drivers provide functions at a layer above the base CAN channel API layer, allowing the simultaneous capture of data from both transactional J1939 packets, and broadcast CAN frames using the ease of the Channel API.

How to process multiple messages through one url over https

Hi,
My scenario is HTTP to IDOC, and the vendor will send different messages through one url to SAP system.
is there any way to achieve this?
Thanks
Jessica

can the Vendor at least pass URL parameters ? Normally, when you have several messages interfaces, the HTTP sender system should distinguish them with the URL parameters (party, namespace, interface). By that, XI then knows how to handle those messages, and can start its receiver determination pipeline. See SAP Help for HTTP sender channel:
Queries entering the plain HTTP adapter must have the following syntax:
http://<hostname:port>/<path>?<query-string>
The query string contains the following data:
●      Sender namespace ?namespace=<namespace>
●      Sender interface &interface=<interface>
These details define the sender interface.
●      Sender service &service=<service>
Specifies the sender service.
●      Sender party (optional) &party=<party>
CSY

Having trouble figuring out how to forward text messages. Can someone tell me how to do that? Where the forward button. You used to be able to hit forward and put radio button on all the messages. The screen looks blank to me.

In the new iOS7, Having trouble figuring out how to forward text messages. Can someone tell me how to do that? Where the forward button. You used to be able to hit forward and put radio button on all the messages. The screen looks blank to me.

In the new iOS7, Having trouble figuring out how to forward text messages. Can someone tell me how to do that? Where the forward button. You used to be able to hit forward and put radio button on all the messages. The screen looks blank to me.

How do I use multiple messages with CAN CREATE MESSAGE?

I'm an old hand at DAQ, but new to CAN.
I need to configure the CAN interface without using MAX or a DBC file directly (because i want the user to configure EVERYTHING in one place, and MAX doesn't handle my other channels).
I can provide the message IDs, channel start bits, etc., etc., by importing a DBC file myself.
So I'm looking at the CAN CREATE MESSAGE vi. I can make it work, using a single message, and a few channels on that message.
But how do I add another message to that task? Or do I create another task to handle a different message?
What's the difference between CAN CREATE MESSAGE and CAN CREATE MESSAGEex? I can't find any in the help docs.
Steve Bird
Culverson Software - Elegant software that is a pleasure to use.
Culverson.com
Blog for (mostly LabVIEW) programmers: Tips And Tricks

you can’t programmatically add messages/channels to an already existing task
So I can't create a task with more than one message, and I can't add a message to an existing task.
That sounds like I have to have a separate task for each message I want. That means separate READ operations at DAQ time. I hope the overhead doesn't cost too much (I'm doing a thousand other things at DAQ time).
I have an RT card in the system I'm designing. It's only using about 5% of the CPU time (PID controlling an engine). Will NI-CAN stuff work on the RT? How do I physically connect it? Is CAN just RS-232 at fast baud rates, or are there more electrical differences?
Steve Bird
Culverson Software - Elegant software that is a pleasure to use.
Culverson.com
Blog for (mostly LabVIEW) programmers: Tips And Tricks

HT3529 How to delete multiple messages at the same time?

I'm new with and IPhone I try to delete multiple messages at the same time. and I can't find how to do this.

Email messages? Tap the edit button...tap each message you want to delete...hit delete...once in trash, tap edit, then tap delete all.

How to show multiple messages for a single exception

hi
Please consider this example application created using JDeveloper 11.1.1.3.0
at http://www.consideringred.com/files/oracle/2010/MultipleMessagesExceptionApp-v0.01.zip
It has a class extending DCErrorHandlerImpl configured as ErrorHandlerClass in DataBindings.cpx .
Running the page and entering a value starting with "err" will result in an exception being thrown and multiple messages shown.
See the screencast at http://screencast.com/t/zOmEOzP4jmQ
To get multiple messages for a single exception the MyDCErrorHandler class is implemented like
public class MyDCErrorHandler
extends DCErrorHandlerImpl
public MyDCErrorHandler()
    super(true);
@Override
public void reportException(DCBindingContainer pDCBindingContainer,
    Exception pException)
    if (pException instanceof JboException)
      Throwable vCause = pException.getCause();
      if (vCause instanceof MyMultiMessageException)
        reportMyMultiMessageException(pDCBindingContainer,
          (MyMultiMessageException)vCause);
        return;
    super.reportException(pDCBindingContainer, pException);
public void reportMyMultiMessageException(DCBindingContainer pDCBindingContainer,
    MyMultiMessageException pException)
    String vMessage = pException.getMessage();
    reportException(pDCBindingContainer, new Exception(vMessage));
    List<String> vMessages = pException.getMessages();
    for (String vOneMessage : vMessages)
      reportException(pDCBindingContainer, new Exception(vOneMessage));
}I wonder if calling reportException() multiple times is really the way to go here?
question:
- (q1) What would be the preferred use of the DCErrorHandlerImpl API to show multiple messages for a single exception?
many thanks
Jan Vervecken

fyi
Looks like using MultipleMessagesExceptionApp-v0.01.zip in JDeveloper 11.1.1.2.0 (11.1.1.2.36.55.36) results in a different behaviour compared to when used in JDeveloper 11.1.1.3.0 (11.1.1.3.37.56.60)
see http://www.consideringred.com/files/oracle/img/2010/MultipleMessages-111130versus111120.png
When using JDeveloper 11.1.1.2.0 each exception seems to result in two messages where there is only one message (as intended/expected) per exception when using JDeveloper 11.1.1.3.0 .
(Could be somehow related to the question in forum thread "multiple callbacks to DCErrorHandlerImpl".)
But, question (q1) remains and is still about JDeveloper 11.1.1.3.0 .
regards
Jan

How to post multiple message using file adapter in XI2.0

We have to post multiple IDOCS.We have scenario as below.
We will have file structure like as shown below.
VKORG,VTWEG,SPART,BSART,PARVW,PARTNER,BSTDK,MATNR,MENGE,VSART,BSTZD,POLINE,BSARK
BE10;10;10;OR;SP;1000033;;M184-ISS01;2;G;131;0002;
BE10;10;10;OR;SP;1000033;;M184-ISS01;2;G;131;0002;
BE30;10;10;OR;SP;1000033;;M184-ISS01;2;G;131;0002;
For this we want that 2
messages should be created.In first message there will be first 2 records
with VKORG BE10 and in second message there will be last record with VKORG BE30.
We can do it through FILE2XMBWITHSTRUCTURECONVERSION and using some options.
I am sending the configuration that I have done for my adapter.
classname=com.sap.aii.messaging.adapter.ModuleFile2XMB
mode=FILE2XMBWITHSTRUCTURECONVERSION
#mode=FILE2XMB
XMB.TargetURL=http://20.60.53.36:8000/sap/xi/engine?type=entry
XMB.ReceiverBusinessSystem=sapdev210
#XMB.ContentKind=B
XMB.ContentKind=T
#XMB.ContentType=application/xml
XMB.ContentType=text/xml
#XMB.ContentType=text/plain
XMB.QualityOfService=EO
##xml conversion properties if mode FILE2XMBWITHROWCONVERSION specified (example, see docu)
xml.recordsetStructure=IDOC,*
xml.recordsetName=SALESDATA
xml.recordsetsPerMessage=1
xml.documentName=SALESDATA
#xml.fieldFixedLengths=
xml.IDOC.processFieldNames=fromConfiguration
xml.IDOC.fieldNames=VKORG,VTWEG,SPART,BSART,PARVW,PARTNER,BSTDK,MATNR,MENGE,VSART,BSTZD,POLINE,BSARK
xml.keyFieldName=VKORG
xml.keyFieldType=CaseSensitiveString
xml.IDOC.keyFieldValue=BE10.
xml.IDOC.fieldSeparator= ;
What I have tried is hardcoding 2 in xml.recordsetStructure=IDOC,2.It works fine
Since I already knew this.
Butin real scenario we wont be knowing this that is why I have given * in configuration , and
given
xml.keyFieldName=VKORG
xml.keyFieldType=CaseSensitiveString
xml.IDOC.keyFieldValue=BE10.
With this it should identify on key field and its value and put first 2 records in one message
and last record in second message.
It is not giving any error when we start adapter but no XML message is created.Can u plz help me
for the above problem.
My datatype in repository is like
SALESDATA
    IDOC
         VKORG
         VTWEG
and allother remaining fields.
Is this scenario possible in XI 2.0.If yes then will it be done through above approach or something else.
Thanx.
Rekha.

Hi,
I think you can not handle this problem with keyFieldName/keyFieldValue.
In my opinion with keyFieldName/keyFieldValue you can create different substructures of the same XML, but you can not seperate messages with the same substructure.
But I don't know how to handle your problem ;-(
Another point is that I see a dot after xml.IDOC.keyFieldValue=BE10.
My be this is a problem too.
Christoph

How do archive all messages over 5yrs old for easy access if needed

My Thunderbird folders are very large after 10 years and I have over 100 sub-folders. I need to keep all messages but would like to keep the oldest, say over 5 years old, separate as I rarely need to see them again. Archiving would make navigation easier. Where in Thunderbird's help pages does it explain how to do this , as well as how to access the archive ? Is it better to make a new profile called Archive and move the archived messages to that ?

Assuming you have all your emails pre-organised in folders called : Acme, Brown, Carter etc
When you created the Archive options, if you had selected yearly and retain folder structure, then it would be archived as follows:
> Archives
> > 2008
> > > > Acme
> > > > Brown
> > > > Carter
> > 2009
> > > > Acme
> > > > Brown
> > > > Carter
If you selected monthly and retain folder structure:
> Archives
> > 2008
> > > >2008-01
> > > > > >Acme
> > > > > >Brown
> > > > > >Carter
This would mean that all the Acme, Brown, Carter folders would be in Archives, but the size of the folder will be smaller because it is divided by year, or even smaller if monthly is used. (If you only have a few emails per month then yearly would be ok). So, if you have not organised your emails into eg: Acme, Brown, Carter folders, then do this first, then when you Archive them they will still be located under Archives in a folder of that name, so easy to locate.
Folders containing emails that you see in the Folder Pane are in reality mbox files - not folders, and these files are stored in your profile folder.
Each file has emails stored one after the other, in the order they were downloaded, so emails are not stored in individual files. If you accessed your Profile folder and opened one of these mbox files using 'Notepad', you would see one huge long document. Each mbox file also has a .msf indexing file.
Large documents carry a greater risk, if something goes wrong, you could lose a lot of emails. The point of using the auto archiving is that this will sub divide those large files into smaller files and therefore carry less overall risk per file and use less memory when accessing.
http://kb.mozillazine.org/Performance_-_Thunderbird
'' Thunderbird loads a folder's *.msf file into memory whenever it opens the folder. By default it keeps up to 30 *.msf files open for 5 minutes (and their contents in memory), unless they are "special" folders, which it never closes. It loads the inbox.msf file for every account on startup. The best way to minimize the amount of memory used is to archive messages you have already read or otherwise no longer need in Inbox into folders that you rarely open. Moving a message to an archive folder opens it, so consider archiving messages by year and month rather than yearly so that the archive being used doesn't get excessively large. ''
If you choose to not use Archive options and instead manually created Acme, Brown, Carter folders in the Archives folder,it means you will have to manually move emails into those folders.
In which case, you will just be creating new large folders, which will get larger everytime you move an email. As they are Archive folders then they will end up with even more emails than you currently have, so I'm sure you can imagine what could happen over time. With Archived emails you need to consider the long term.
At the end of the day the choice is yours, but at least you now have some information to make an informed choice.

How to delete multiple messages in mail

How to select a bunch of messages in mail to delete.

I Wonder if your sitting there laughing at us as if there is some big conspiracy about selecti all and deleting all from our iPhones and iPads.
The conspiracy.
Why can we not just not select all in the mail inbox and then delete all, if we do not want to delete every single one of them then deselect the few that we do not want to delete instead of having to select the thousands we do want delete individually.
And if you do make a mistake and delete the wrong emails by selecting all, then go to your trash and reinstate the ones you did not want to delete
I think 99% of us know how to DELETE emails individually, as you put it.
That's just sarcasm and if not then then your not fully understanding the question asked.
I would also say that probably 99% of us want to be able to select all and delete all if that's what we desire.
I would just like a honest answer of why we cannot select all delete all rather than giving me a load of rubbish about encase we delete something we didn't want to delete.

How to specify multiple message bundles in faces-config.xml

Hi
I have different properties file which I want to use as message bundle.
Message.properties
Help.properties
When I specify this in faces-config.xml
<application>
<message-bundle>/Message</message-bundle>
<message-bundle>/Help</message-bundle>
</application>
and now when I try to use that in my jsp page like this
<f:loadBundle basename="/Message" var="message"/>
<f:loadBundle basename="/Help" var="help"/>
and access any messagestring from those files I can not excess either of them. But when I use only one of them it works fine.
Am I doing something wrong or I can not do this thing at all??
Thanks in advance.

I only specify one properties file in the <application> tag. That one is used for system messages. I have other properties files for labels, and another for just standard app text, so in my faces-config.xml I have something like this:
<application>
<message-bundle>message</message-bundle>
<locale-config>
<default-locale>en</default-locale>
</locale-config>
</application>
where my message.properties is used for system messages (validation, etc).
I don't list the other property files there. I have two more that I use, labels_en.properties, and standard_en.properties. Labels are words that have a : at the end or a *: for required fields. Standard are just other words that I use in my application. So on every page that I have, I start out with the following header:
<html>
<f:view locale="en_US">
<head>
<f:loadBundle basename="label" var="label"/>
<f:loadBundle basename="standard" var="standard"/>
<title>
.....

How to delete multiple messages in the same mailbox all at once? Unity Connection

I just was assigned the task of administrating three Unity Connection servers that are networked. The Operator mailboxes on each system have been taking messages since 2010 and have over 5 thousand messages in them (nearly 3 mega bytes). I've corrected the set up so the mailboxes no longer are taking messages, but would like to delete all the new messages in order free up memory resources, and I don't want to undo all the Call Handler relationships in order to delete the mailboxes and then recreate them, etc. I used the PCA tool to clean up the Operator MBX on a standalone Unity Connection that had nearly 1800 messages, but it took nearly 30 minutes for the PCA tool to load and another 4.5 hours to delete one message at a time (major carpal tunnel afterwards!). For these mailboxes with 5-6K messages, the PCA tool was not loaded after 3 hours!   Is there a faster, more efficient tool for deleting all new messages in a single mailbox? (i.e., Message Hunter?)

Hi There,
+5 to heath for his good notes!
One nice way with Unity Connection is with the use of this excellent tool from the great suite of Unity Tools (use the ** reset" feature **).
Unity Connection Bulk User Delete
For resetting users you have the option of emptying the mailbox, resetting greetings, deleting voice names, resetting passwords, removing private lists and a number of other options you may choose.   For installations where the user base “changes over” frequently such as schools this may be a nicer option. This option is also allowed for CoRes installations since it does not involve the removal of user objects from the Connection database.
http://www.ciscounitytools.com/Applications/CxN/BulkUserDelete/BulkUserDelete.html
Cheers!
Rob
Please support CSC helps Kiva
https://supportforums.cisco.com/blog/12122171/cisco-support-community-helps-kiva

How to avoid multiple messages in Moni

Hi all,
i am doing a Multiple Idoc to file scenario.
evryday 30000 Idoc will be sent . have to collect all the record in a single file.The scenario is working fine.
But its creating 30000 entries in moni...
is there any way to send all the Idocs or may be 1000 idocs at a time so that only 1 entry is there in MONI?
regrads
Biplab

Hi,
Collection of IDocs can be done with BPM and without BPM see the below links
/people/pooja.pandey/blog/2005/07/27/idocs-multiple-types-collection-in-bpm - Collection of IDoc to Single File
/people/stefan.grube/blog/2006/09/18/collecting-idocs-without-using-bpm -collecting IDocs without BPM Idoc - Multiple - interfaces - Idoc to multiple interfaces in XI
Please reward points if it helps
Thanks
Vikranth

How to forward multiple messages in icloud mail

I need to forward 22 messages in icloud to someone. I have created a folder and placed them in it. I am using icloud in Win 7 pro on an HP laptop (have iPhone 5) and have tried sending them on icloud in the following browsers: chrome, firefox, safari, internet explorer. When I select more than one message in the folder, then attempt to click on 'forward,' it is grayed out. It seems icloud only allows forwarding one message at a time. Some of these messages have lengthy attachments, so cutting and pasting them into one email individually is silly. Any suggestions greatly appreciated.

The problem with mail is it uses a huge amount of broadband. Also takes up a lot of disk space. Thats why I use icloud mail. On both my imac and laptop I would be using double the broadband.
Sounds like there is no way to download several attachments at once on icloud mail?

How to handle the multiple message on the screen

I am new to j2me. I am trying to write a simple program for instant messaging. I want to write a program that to handle incoming messages. Now I am able to display one message at a time but I dont know how to handle multiple messages. Do anyone can give an example?
Is that anyway that pop up an indication for new messages in j2me?
Need yours expertise to help me. Thanks.

Use a custom canvas to display messages. Then you can do whatever you want with it!

How to transmit multiple messages over CAN

Similar Messages

Maybe you are looking for