How to use partial number of PPMs to generate SNP planned order

Hi all,
I have a requirement for SNP where I have got X number of identical work centers, on which an SKU can be manufactured. Now there are limitations at the operational level on the labour force or any other constraints, due to which only Y number of work centers can be operational on any day (X>Y). So effectively an SKU can use only Y number of PPMs out of X PPMs in the system on any particular day. X and Y are fixed.
I have tried to map the same by creating a bucket resource with bucket capacity Y and attached to all X PPMs and taken SNP optimizer run. It restricts the output quantity of the planned order by that of the bucket resource defined.
Is there a way to map this requirement, i.e. restricting the number of PPMs which the SKU can use on any day?
regards,
biplab

Hi,
You can try this by defining the down time for the particular resource in APO under downtime tab page.
Ex for a entire week.
I tried by locking the resource for the entire week and also removed the Maximum delay specified in the product master in our case.
Took the opt run and system is not suggesting the plans.
Or
You can make the PPM inactive before your run.
Request you to test and confirm this
Thanks,
nandha
Edited by: S.Nandakumar on Oct 4, 2010 9:34 AM
Edited by: S.Nandakumar on Oct 4, 2010 9:38 AM

Similar Messages

How to generate SNP planned order with different category

Our SNP system receives Forecast and Salse Order from DP system.
and we'd like to generate SNP planned order with different category..for example, 'AI' for Forecast Demand and 'AL' for Sales Order..
currently, If we run CTM, system generate SNP planned order with the
same category 'AI'..
another system(APS) in Our company receives planned order from SNP
and they want to receive planned order for forecast and planned order for sales order seperately..

It is not directly achievable however can be done through BADIs and two CTM profile. I am assuming that sales orders are planned ahead of Forecast demands. So have two CTM profiles - one for Sales Orders (regenerative mode) and the other for Forecast Demands (net change mode). You may have to invoke two BADIs in the first run for Sales Orders - one that changes master data by putting a temperory Forecast Horizon in SNP2 tab (BADI /sapapo/ctm_matloc). The other BADI (BADI /sapapo/ctm_orders) changes the ATP category just before saving. in the second run though you just need to run the latter BADI by saving it in the ATP category required. BADIs can be invoked based on CTM profiles used.

How to pick up a specific PPM for a particular planned order ?

I have created a specific PPM --now How to make a planned order in rrp3 pick up this specific PPM and cancel the original one ?
i don't find a solution for this in SCC03 in which t code ....can we assign a PPM with a planned order ?
Thanks
Ohio

Hi Rahul,
You can change the PPM for an order.
Follow the below given steps.
1. Go to transaction /sapapo/rrp2
2.Enter the logical system, APO order no. and planning version.
3.Click on change button
4.In the following screen, click again on change button which is provided to change source of supply.
5. In the pop up choose the newly created PPM and click on adopt.
This order would now be assigned to the newly created PPM.
Hope this helps!
Regards,
Jyoti

How to use Partial Page Navigation

according to Web User Interface Developer's Guide for Oracle Application Development Framework section 7.4.1 How to Use Partial Page Navigation,
I set 'oracle.adf.view.rich.pprNavigation.OPTIONS' to 'on' in the web.xml.
and in the jspx, I use af:commandNavigationItem to navigation and set the tag 'partialSubmit' attribute to true.
But it does not work. does anybody know how to use this feature?

Hi,
the question is "what does not work". Partial Page Navigation is there to improve performance on page navigation. So if you navigate from page1 using a navigation case to end up at page 2 then the outcome of the command action's action property should match the navigation case name.
Frank

How to use the selection profile and status profile for production order?

Hi expert,
I want to know how to use the selection profile and status profile for production order. what's the usage for these two selection profile and status profile ?
Please help me.
thanks in advance.
george.shi

Hi George,
There are are two types of statuses.One is system status and second one is user status.These statuses will tell us current situation of an order.
We can't change system statuses.But we can create our own statuses through status profile.With this profile we can control user statuses.
In this status profile,
1.We define the sequence in which user statuses can be activated,
2.We define initial statuses
3. Allow or prohibit certain business transactions.
Selection profiles are used to select the objects (say production orders) with different status combinations.We assign status profiles to selection profiles in BS42 T-Code.
Regards,
Raja.
Edited by: Rajarao on Oct 30, 2008 6:21 AM
Edited by: Rajarao on Oct 30, 2008 6:22 AM

Creating SNP planned order using ''BAPI_MOSRVAPS_SAVEMULTI3'

Hi Experts,
I am new to SAP-APO, kindly clarify my question. I am using 'BAPI_MOSRVAPS_SAVEMULTI3' with source of supply PDS for creating SNP planned order by passing 'EE' in the table parameters 'ORDER_HEAD-MASTER_ATPCAT'. It is creating a planned order which is PPDS planned order with number range starting from '1000...' rather than creating SNP planned order with number range starting from '8000..'. Please let me know what might be the reason for the BAPI misbehaving incorrectly. Also kindly let meknow what are specific parameters to pass to above bapi to create SNP planned order.

Hi,
The BAPI BAPI_MOSRVAPS_SAVEMULTI3 is used for creating PPDS inhouse orders.
You will have to use BAPI_MOSRVAPS_CREATESNPORDER for SNP inhouse orders creation from SNP PPMs( there is no explict mention of SNP PDS- you may please check).
Regards
Datta

How to Change Component on a SNP Planned Order ( Just 1 time )

Hello,
We are trying to change a component on a SNP Planned Order just 1 time.
So we do not want to change the PDS since this is one time change only.
We tried changing it in R/3. Once we do that, R/3 shows new component but APO still shows dependant demand on old component ( May be because APO SNP Planned order is still connected with the PDS ) .
Then we went to APO and tried to change the component in /sapapo/rrp3. Here you can delete the old component but doesn't let me add new component.
Next thing we tried was to convert it to PPDS Order. Once converted, we went to change mode and tried to remove old component and add new component. It lets me do this. Only issue with this route is that, it puts correct start and end dates on the order dependning on the order quantity and so order moves the dates which we do not like.
Is there any other better way to fix this issue ?.
Thanks.
Ketan Doshi.

This being a very unique requirement, I would use one-off approaches usually not followed. You may need to explore the use of BAPI BAPI_MOSRVAPS_CREATESNPORDER. This will help you point the source of planned order to a PPM or a PDS that you may want to create in APO system on a one-off basis. PPMs can be maintained in APO, however PDS are usually CIFed from R3. You can try to create PDS (based on the new component) in APO system only using backend tables. Try do some little research on /sapapo/curto tables to create the PDS in APO. Then use the BAPI to point the source to this new PDS. (better you also try the PPM approach since there are no issues keeping the PPM in APO)

SNP Planned Order without PPM

Hi Gurus,
I have a small confusion, Some of my products in a Production Plant donot have a SNP PPM. and when i run network heuristic on that location product. It creates SNP Planned orders.
Just for information the product location master has procurement type E (In House Production).
Please help me out if this is a normal behavior of the system.
Thanks,
M

Default behavior is to generate Orders without a source of supply.
"If there is neither a valid transportation lane (for procurement type F; external procurement) nor valid PPM/PDS (for procurement type E; in-house production), the system creates an SNP stock transfer or SNP planned order with no reference to a source of supply. The same applies if there is no product at the source location of the transportation lane"
if you dont want planned orders there,
Try using the SDP relevance indicator for the location - product . Am not sure but you can use option 1 in it (though it sounds like it will not plan in DP too)

Creation of SNP Planned Orders using Optimizer

Dear Experts .....
I am facing some problems while creating SNP Planned orders using Optmizer ( Discret Optimization).....
For eg.
I am using 3 months horizon ... the first two months is daily buckets with 12 hours capacity each one and the last month is weekly buckets.
The product minimun lot size exceed the daily capacity .... this way planned order have been created in the weekly buckets at the end of the horizon.
I need the system to create orders in the correct date avoiding use of safety stock .....
Regards
Mauricio

Those other 2 settings was already done .....
It is still not working .... iI am receiving the following message ...
Production process model/PDS 00000000000001011301001 S: Cannot be executed
Message no. /SAPAPO/SNPOPT159
Diagnosis
Production process model 00000000000001011301001 S at location 0100 is intended for cross-period lot size planning. It can be started in bucket 20110404->20110404. However, it does not then end in the same bucket.
Thanks for your effort trying to help me with this issue.

How about use partial key to loop at a hashed table?

Such as I want to loop a Internal table of BSID according to BKPF.
data itab_bsid type hashed table of BSID with unique key bukrs belnr gjahr buzid.
Loop at itab_bsid where bukrs = wa_bkpf-bukrs
and belnr = wa_bkpf-belnr
and gjahr = wa_bkpf-gjahr.
endloop.
I know if you use all key to access this hashed table ,it is certainly quick, and my question is when i use partial key of this internal hashed table to loop it, how about its performance.
Another question is in this case(BSID have many many record) , Sorted table and Hashed table , Which is better in performance.

You can't cast b/w data reference which l_tax is and object reference which l_o_tax_code is.
osref is a generic object type and you store a reference to some object in it, right? So the question is: what kind of object you store there? Please note - this must be an object reference , not data reference .
i.e
"here goes some class
class zcl_spfli definition.
endclass.
class zcl_spfli implementation.
endclass.
"here is an OBJECT REFERENCE for it, (so I refer to a class) i.e persistent object to table SPFLI
data oref_spfli type ref to zcl_spfli.
"but here I have a DATA REFERENCE (so I refer to some data object) i.e DDIC structure SPFLI
data dref_spfli type ref to spfli.
So my OSREF can hold only oref_spfli but it not intended for dref_spfli . That's why you get this syntax error. Once you have stored reference to zcl_spfli in osref then you will be able to dereference it and access this object's attributes.
data: osref type osref.
create object osref_spfli.
osref = osref_spfli.
"now osref holds reference to object, you can deference it
oref_spfli ?= osref.
osref_spfli->some_attribute = ....
OSREFTAB is just a table whose line is of type OSREF (so can hold multiple object references - one in each line).
Regards
Marcin

How to use page-number in xsl:if

Hi
I would like to use <fo:page-number/> in my if clause. Based on page number, I would like to add some more fields.
If help on this greatly appriciated.
Thanks,
Ram.

i'd like to check page num, if page num > 1 then output current page of total pages. if it's possible, plz tell me how?
because i used check row num to do this, its not right method.

IMessage on MacBook Pro - how to use mobile number?

So I upgraded to 10.8.2 on ML and IOS 6 on other devices. I notice on the iPhone that my iMessages can be received by default only to the mobile number.
I previously turned iMessage off because frankly it was a complete PITA and more trouble than it was worth. The mess created for recipients with messages coming from apple IDs when sent from the iPad and from a mobile number on the phone, then messages sent from one not showing on the other, replies not going from one device becase there was no internet available but the message had come to the apple ID and not the phone number etc etc. The woes went on. iMessage thus went off.
Now, the ability to use the phone number as the default across decvices did sound appealing and I THOUGHT that when I activated imessage on the Mac and iPad it would automatically show up with the option to use the mobile number on those devices. Instead I just get the email option and can see phone number at all.
Am I correct in assuming that I need to add the Apple ID so messages can be sent there BUT configure it somehow so that iMessages going out from those devices are sent as coming from my mobile and not an email address? last thing I want is the dog's breakfast that the last incarnation of iMessage brought and I would hope this time around that "It just works". I'm gettng more and more used to having to probe around with Apple though, to find ways to make it work.

Finally got this to work, coincidence or not i'm not sure, maybe the system was just catching up. On the iPhone I ONLY had the telephone number enabled. I then added the Apple ID and all the test messages arrived, as did the mobile number verify message. I then went and turned the Apple ID email off as a 'receive at' source. After that the mobile number was verified on the Macbook and was available to add as an iPad 'email address'.

How to use bullet number characters in a list?

As you can see in the screenshot above, I'm using bullet characters (from Wingdings) to create a numbered list. It may look fine; however, inserting these characters manually can't be the most efficient way to pull this off. The character after the fourth bullet is an “indent to here” character.
Can this style of bullets be automated using a real bulleted list in InDesign?

Geert DD wrote:
Okay, I found one: Fyra. This works fine for lists up to nine bullets.
On MyFonts.com I found more similar fonts, and they're set up like this:
The numbers 1-0 reside on the standard keys. Two digit numbers 01-99 can
be composed out of left and right half circles by using (lowercase)
‘abcdefghij’ for the first digit (left half circle) and ‘lmnopqrstu’ for
the second digit (right half circle). The critical pairs (all combinations with 1) can be found in various
places. Type ‘!’ for 10, ‘#’ for 11, '$‘ 12, ’%‘ for 13, ’&‘ for 14,
’(‘ for 15, ’)‘ for 16, ’*‘ for 17, ’+‘ for 18, ’,‘ for 19, ’-‘ for 21,
’.‘ for 31, ’/‘ for 41, ’:‘ for 51, ’;‘ for 61, ’?' for 81, ‘_’ for 91.
For manual insertion, that works fine. It seems impossible to automate, though.
However you achieve the result manually, I don't think that lists will number automatically, because these are graphics, not true numbers.
A Google search for "circled number fonts" without quotes returned a lot of links, but none seems to have great confidence. Perhaps other search terms will find the magic "bullet" you are looking for.
You can ease the pain a bit by creating a set of the numbers you need and storing them in an InDesign library or simply a standard InDesign file, then copy and paste when you need them.
HTH
Regards,
Peter
Peter Gold
KnowHow ProServices

Grade book percentages - how to use partials

I'm using the Grade Book template in Numbers
I have five assignments worth 1/2 point each
How can I insert .5% as a percentage of !00% in my grade book? When I do that it results in 50%
Thanks!!

1. Make sure your cells are formatted for percent.
2. Append the % sign to your entry if the value is <1% (+/-) - this is a known data entry anomaly
For example if you enter 5.7 for 5.7% and your cell is formatted for percent, your result will be 5.7% in the cell.
If you enter 0.45 in a cell formatted for percent, the result will be 45% (not what you want) so, instead, enter 0.45% and the result will be 0.45% (correct) - anything less than 1 percent seems to need the % sign added.
See the discussion here: https://discussions.apple.com/message/17624595#17624595

Has someone knowlege of how to use Custom Number Format in Numbers V3.0

Hello Everyone,
From Excel to Numbers '09 I worked with Custom Number Format.
Making formats like 60 sec, km/h or m/s².
In the new Version 3.0 it is not under 'Format'/Custom Number Format.
I did not find it! Has someone found a way to do it the old way.
I am working with the German version.
Bye

Limmy,
There is no option in Numbers 3.0 for Custom Format. If that is mandatory for your purposes, it is still available in Version 2.3.
Jerry

How to use partial number of PPMs to generate SNP planned order

Similar Messages

Maybe you are looking for