HP Laserjet CP1025nw problem with network setup

I want to ask does this printer model have some defect when connected to network? Because we tried to connect it via wired network and it will work by a few minutes then after it will not connect. I tried pinging and it shows destination host is unreachable. It was manually set for IP Address.
We sent it back to the vendor to get a new one and still the same problem persist. We tried different HP Printer model but it does not cause any problem. I am very sure problem arises from the printer.

Hi,
I uses the CP1025nw on a wired connection on a general manner with no such issues.. it is not a model defect or similar.
Have you tried using a different ethernet cord?
Have you tried plugging the cable into another port lan of your router?
While the computer cannot connect to the printer, does it have an IP address available or will it fully disconnect from the network? (that is in order to better understand if the printer disconnects or only not available for the computer)
Does the same happens from a single computer or do you see the same behavior from other devices on your network?
I suggest connecting the printer with a USB and updaing the latest firmware, that can be download from the following link:
http://ftp.hp.com/pub/softlib/software13/COL34894/lj-115939-3/LJCP1020_FW_Upgrade_Security-20150114....
Once you are done check for any difference. if the same persists try connecting an ethernet cable directly from the printer to your PC to ensure its functionality.
Can you see any similar behavior or may you see any difference? that allow isolating any cause to better understand if that also happen on a direct connection, (to simulate a different network).
Please let me know the results,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Similar Messages

Problems with Airport setup after buying Version 7 models, (older ones will not upgrade)

Problems with Airport setup after buying Version 7 models, (older ones will not upgrade)
I re set up my Airport network , having had 4 expresses for years doing a good job. I bought another and an express, but then a time capsule after my external drive died. .Problems with Airport setup after buying Version 7 models, (older ones will not upgrade)
I moved house and have fibre network so 38mb/s - they all look ok on the utility, but its not till I saw the App version that they are not compatible as mac will not upgrade the version 6 ones, leaving me with 2 disjointed networks and 7 appliances, 4 of the old , 3 of the new.
my new house is expansive so i wanted the extended range and airplay in each room.
This is not told to customers, and utility doesnt show any issues.
I do not seem to get any range from either network now, - and I'm quite experienced with airport (6 yrs of setting up & using & extending)
Any advice ?
LJx
Message was edited by: LJLDN
Message was edited by: LJLDN

Sorry couldn't change the detonations to Airport and am new so cant delete!

Problem with network on Iphone 4

Please tell me if someone has a problem with network on Iphone 4?

Of course other people have had problems. However, just knowing that other people have had some vague, undefined "network problems" most likely isn't going to be very useful. You'll get more and better help if you can give some details about your specific problem. Include who your carrier is, what country you're in. Then describe the exact nature of the problem. Then, maybe someone will be able to give good suggestions.
And, by the way, the free bumper program ended some time ago. It also was only a "solution" for one of many possible problems.
Best of luck.

Since I upgrade my iphone 3gs to ios 5.1, I have several problems with network and wi-fi, any solution?

Since I upgrade my iphone 3gs to ios 5.1, I have several problems with network and wi-fi, any solution? (No jailbreak)
Most of the time the iphone cannot reach any network and when it can, there is no data transfer, I can only make calls and sms.

Skizofrenias wrote:
Since I upgrade my iphone 3gs to ios 5.1, I have several problems with network and wi-fi, any solution? (No jailbreak)
Most of the time the iphone cannot reach any network and when it can, there is no data transfer, I can only make calls and sms.
iOS: Troubleshooting Wi-Fi networks and connections
iOS: Wi-Fi or Bluetooth settings grayed out or dim

Facing problems with network due which the phone goes into hangs status

Facing problems with network due which the phone goes into hangs status. some one help me with switching between 2g and 3G network

Hi Mani Nair,
I apologize, I'm a bit unclear on the exact nature of the issue you are describing. If you are talking about having issues with a 3G cellular data network, you may find the troubleshooting steps outlined in the following article helpful:
iPhone cellular data connection issues
Regards,
- Brenden

SAP Screen Personas error "A problem with network connectivity has been detected"

Hi,
We just installed Personas release 100 SP02 and performed the
configuration steps necessary. But when we acces the url and logon to
personas we get the following erre
A problem with network connectivity has been detected.
Please check you connection and refresh your browser.
Any help to solve this issue would be appreciated.
Best Regards.

Please use this checklist to see if everything is correct:
1. restgui service handler class has CL_HTTP_EXT_ITS_BASIC
2. SPRO -> Sap screen Personas -> Maintain system has
       - 3 letter system id
       - "Server.Url" without typo and value in http(s)://<SERVER>:<PORT>/ format
       - "Service.Uri" without typo and value as /restgui
3, Note 2026487 is installed
4. If target system is different from source system then you are able to access the following
         - http(s)://<TARGETSERVER>:<PORT>/clientaccesspolicy.xml
         - http(s)://<TARGETSERVER>:<PORT>/crossdomain.xml
5. role is assigned to user under /n/persos/admin_ui -> User Maintenance -> Search -> Show user -> Role
If you still get error, then if you are using SSO, please check if you have configured login/create_sso2_ticket parameter correctly.
Thanks
Chinthan

Upgrading to 6.1.1 hasn't solved the problem with network connection on 4S. Still "No Servise"!

Upgrading to 6.1.1 hasn't solved the problem with network connection on 4S. Still "No Servise"!

Same here. Everything was fine running on ios 6.0, I don't know what possessed me to upgrade! I contacted O2 and thet went through the usual settings; reboot; airplane mode etc and it works for a while (like 5 mins) then service is losted with the network. I've even deleted the exchange email account and rebooted as read on the internet that this would fix the problem.... guest what....yep no joy! This is clearly a faulty software update and need fixing pronto! I've read that ios6.1.2 will be out soon to fix the firmware that was suppose to fix the initial network problem. When will this be realeased Apple?! It's hardly fit for purpose when I can't make calls or surf the internet.

Problem with networking HP Laserjet 1100 with Leopard with new Intel iMac

I have an HP Laserjet 1100 that I have used with my old iMac running Panther. I had used the HPIJS drivers in the past with the HP Laserjet 5 driver selected. It worked flawlessly. I use IPP to connect to the printer via a printer server.
I have purchased a new iMac which is Intel based and runs Leopard. I am having a lot of trouble getting this printer to work with it. I went to the website referenced above and installed Ghostscript, Foomatic RIP and then finally HPIJS. As I add the printer, it gave me the option to select an HP Laserjet 1100 printer (from the HPIJS set). When I add the IP address, it says it is valid. When I try to print, there is no response; the job just times out. I had the same problem with the Gutenprint driver that was installed with Leopard.
Finally, I tried the HP Laserjet 6 from the HPIJS driver set. It had the word "recommended" next to it which was intriguing. It too did not work.
I would appreciate any help.
Steve Kirchner

I'm afraid that Ghostscript, etc. are PPC only applications and any printer plug-ins they install will not work on an Intel Mac. You should uninstall all the third-party stuff you've installed for the printer, then only use the included printer driver installed by OS X unless HP has a universal binary driver compatible with OS X and Intel Macs. You might try using LPD rather than IPP for the printer.

Communication problem with network printer

I have a Lexmark X9350 all-in-one printer. It has a built in wireless card and I am trying to print to it from my Powerbook G4. I have an airport extreme network setup in my home, and my PC is able to access the printer just fine. When I installed the printer software on the mac, it recognized the printer on the network and worked at first, but then suddenly couldn't find the printer. When I uninstalled and reinstalled the software it was very strange because when I got to the point where it searches the network for a printer, sometimes the printer shows up, and then if I click to refresh the printer sometimes disappears. It is not an issue with being out of range, because the printer display tells me it has plenty of connection, and as I said the PC can print with no problems. It appears to be something specific with Tiger not being able to consistently detect the printer.

I would look at XP's port configuration for the printer and then try and use the same protocol on the Mac. If XP is showing it as RAW Port 9100, then that is shown as HP jet Direct - Socket on the Mac. The only issue then is whether the OS X driver is available in the Lexmark list. Sometimes the provided OS X driver is only for direct USB connections, so you have to look at using an alternate driver, such as those offered by Gutenprint.

Problem with network printer on Windows 7 machine

I'm running Mavericks on a Mac Mini. I have a Windows 7 machine with an attached Brother HL-5340D printer. I'm using the Brother HL-5340D CUPS driver. Whatever configuration I use, I cannot get my Mac to print from the Brother. I have even set up dhcp on the Mac and connected to the Windows machine with a cable. I have tried ipp, ldr/ldp, windows, ip, and most of the relevant options under advanced, and nothing works. I've run out of ideas on what to try and how to test and where to look for hints. All I get is the following:
Unable to connect to ‘192.168.33.2’ due to an error.
Not a lot of help.

James Wilde wrote:
1. I forgot to say that it was the Mac equivalent of dhcpd that I turned on so that the Mac is the server, on 192.168.33.1, and it has assigned the number 192.168.33.2 to the Windows box. And yes, I do prefer in these cases to use fixed addresses, but the Windows box seemed reluctant to accept its ip address thus the decision to start dhcpd on the Mac. After that I could not ping the Windows box from the Mac box. I didn't try to ping the Mac from the Windows box. I'll try that tomorrow. As to the network, there are only these two machines on the cable network. The default router on the Windows box is, if I remember correctly, set by dhcpd to the ip address of the house router. I have now disabled the cable network. See below.
Unusual that you could not ping Windows from the Mac. Would explain why you got a connection error with this setup. But if you have now stopped using the cable connection then this is mute.
James Wilde wrote:
2. The network profile is set to Home on the Windows box. I don't see any references to Homegroup in any of my messages on this topic. If you are referring to another post I made on a different subject, I am aware of the problems with Homegroup, and as far as I know, I have avoided this, since my wife's Windows box is the only Windows box in the house. Everything else is either Mac or Ubuntu, apart from one or two Windows virtual machines on my Mac and Ubuntu boxes.
No, you didn't mention Homegroup but you did mention not being able to see the Windows computer "Incidentally I now find that I can't get any result from selecting Windows in the Add Printer dialog." So I thought I would mention that Homegroup can cause this.
James Wilde wrote:
3. I've tried all three options in the Add printer dialog, IP, Windows, and Advanced. Under Advanced I have tried lpd and spoolss and ipp, under ip I have tried ipp and lpd. The share name is Brother-HL-5340D, and the hyphen between Brother and HL I put there myself to make it one 'word'.
I've just tried your suggestion and get the following when I click on Add.
Unable to verify the printer on your network.
Unable to connect to ‘192.168.1.202’ due to an error. Would you still like to create the printer?
I've seen this occur when the LPD process is not working. Open the Services pane on the PC and check the LPD service has started. If it is running and you still get the error message, what happens if you say yes to creating the printer?
James Wilde wrote:
As i said, I have disabled the cable network and am using the house wifi network (all machines with fixed IPs). I can ping the computer and have just mounted a disk on her computer with smb using Finder/Go. The mount does appear to be read only, but at least I can open all the folders.
Anything else I can try?
That is a good outcome. Proves there is a functional path between both computers.
Since you can connect using SMB, and if you cannot LPD to work, then try adding the printer again using the Windows view in the Add printer pane. You should see the workgroup used by the Win7 PC followed by the Win7 computer name. Selecting it should prompt you to authenticate (unless you have saved the account in Keychain) and then the printer share name should appear. After selecting the share, select the Generic PS driver as a test to see if you can submit a print job - open the print queue on the Win7 PC to see if the print job appears. If this does work, you can remove the printer on the Mac and add again, this time selecting the Brother driver and then see if this works.

Windows 8/8.1 Partial Print Problems with Networked Inkjet Printers (Envy, Officejet and Deskjet)

There are a lot of threads being posted about this problems with printing on the following these devices when they are connected in a Network Environment (Wireless or Wired)
HP Officejet Pro 6830
HP Officejet 6800
HP Officejet Pro 6230
HP Officejet 6220
HP Officejet Pro 8610 e-All-in-One Printer series
HP Officejet Pro 8620 e-All-in-One Printer series
HP Officejet Pro 8630 e-All-in-One Printer series
HP Officejet Pro 8640 e-All-in-One
HP Officejet Pro 8650 e-All-in-One
HP Officejet Pro 8660 e-All-in-One
HP Officejet 7610 Wide Format ePrinter
HP Officejet Pro 3610 Black and White e-All-in-One
HP Officejet Pro 3620 Black and White e-All-in-One
HP Officejet Pro 251dw Printer series
HP Officejet Pro 276dw MFP series
HP Officejet 7110 Wide format ePrinter
HP Officejet Pro 501dw Printer
HP Officejet Pro 401dw Printer
HP Officejet Pro X451dw Printer
HP Officejet Pro X576dw MFP
HP Officejet Pro X476dn MFP
HP Officejet Pro 451dn/551dn MFP
HP Officejet Pro 451dw/551dw MFP
HP Officejet 4630 e-All-in-One
HP Deskjet Ink Advantage 4640 e-All-in-One Printer series
HP Deskjet 2540 All-in-One Printer
HP Deskjet Ink Advantage 2540 All-in-One Printer
HP ENVY 5530 e-All-in-One Printer
HP Deskjet Ink Advantage 4510 e-All-in-One Printer
HP ENVY 4500 e-All-in-One Printer
HP Deskjet Ink Advantage 3540 e-All-in-One Printer
HP posted a workaround for this problem while they were working with Microsoft to get the root cause of the problem, many customers commented that the workaround helped them out and they were able to print. This workaround was not easy to use as the customer needed to add another printer manually and changed drivers.
We can now announce that the problem has been fixed, the problem involved a Microsoft Network component that HP was using to talk to and track the printers on the network. This fix is being rolled out by Microsoft via Windows Update and anyone who has Windows Update enabled and set to automatically install updates should have already received this update. For those that do not have Windows Update setup to automatically install fixes the fix is available now and should be installed.
The details of this fix and a manual method of installing it can be found here.
http://support.microsoft.com/kb/3000461
This fix is only designed for users that are using there printer on a Network (Wireless or Wired) and will not fix partial printing problems encountered with USB connections.
There are many threads in HPs forums about this issue (below are links to a few of them)
http://h30434.www3.hp.com/t5/Printing-Issues-Troubleshooting/Missing-partial-prints-amp-Printer-Offl...
http://h30434.www3.hp.com/t5/Printing-Issues-Troubleshooting/HP-Envy-4500-cancels-job-in-the-middle-...
http://h30434.www3.hp.com/t5/Other-Printing-Questions/Only-prints-half-a-page/m-p/4054888
JonW
I work for HP

@tenkeypro
First, I would suggest you uninstall the exsisting driver and reinstall following one of these documents to see if it will clear this error message:
Install HP print and scan software on a Windows 8 computer (32-bit and 64-bit)
Universal Print Driver (no scan)
Driver support included in Windows 8 / Windows 8.1 or in Windows Update
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

Solaris9 x86 problem with network cards, ACPI, IRQs

Hello!
For the last two days I've been trying to solve the problem of Solaris9 x86 not being able to use my network card. I have tried with 3c905CX-TX-M, RealTek 8139 and Realtek 8029 and none of them works. The problem is the following:
Everything is properly configured, networking etc., but the cards can only send and cannot receive packets. When trying to ping, the packets leave the NIC but none of the reponses are detected by NIC. When I check with 'kstat elxl' I can see that 'intr' is zero, and out_packets is increasing as it's sending packets.
From the discussion forum I can see that this same problem has been known for several years. One of the conclusions is that Solaris x86 sucks at dealing with IRQ setup and that the best thing is to disable ACPI and 'PnP OS' option in BIOS. However, I've tried all releases of AMI bios and none them has neither of those options. I have played with various priority levels in BIOS but all that has accomplished is that the card, when first started, captures a few interrupts/packets but then stops again. This is usually just enough to finish the ARP exchange (arp -a shows the remote host).
And of course, all the cards work just fine in WindowsXP and Linux. And all the cards work nice in another PC which runs the same Solaris 9 x86.
My motherboard is Gigabyte 7VTXE. (The other one in which it works is ASUS P2B-DS).
I would really appreciate help!
Josip

I had almost identical problem today on an HP Kayak - which happened to be dual CPU one. The fix
set pcplusmp:apic_forceload = -1
in /etc/system worked for me. The only drawback is that it also leaves the machine single CPU. AFAIK this (downloadable) S9x86 kit is licensed only for one CPU anyway, so I wonder if something has been fixed in the code to make sure it is not run on multi-CPU systems. Before the fix, mpstat showed thousands of interrupts on CPU0, both CPUs were constantly busy at about 70% and there was no network connection on a number of cards I tried (3Com 90x - elxl, Intel iprb, another one with Realtek 8139 was never recognized, so I did not bother too much to find if there is a fix for this); pinging out resulted in the hub port light blinking, nothing comes back.
Anyway, the fix is good enough to test s9 for now; everything else seemed to be OK. If it may be of some use for somebody, don't go into the disk option of the Solaris Management Console; the machine in question had Windows 2003 server (RC2) installed before Solaris9, the disk tool decided that there was no label on the disk and asked to write it on; I clicked the 'cancel' button, but the partition table was irreversibly damaged, so I had to start from installing W2k3. My guess is that tool has been tested only with Sparc, so there is no issue with BIOS level partitioning there. BTW, system info of the SMC insists that the CPUs are Sparcs...

Problems with Email Setup

I purchased a Blackberry Curve 9330 a few days ago, and am having problems with the email setup. I previously had an older model of the Curve, so have used Blackberry for email before. I'm going to Messagex ---> Options ---> Email Account Management and I get the following message:
"A new BlackBerry device has been detected. You must move email account(s) to resume email delivery to your BlackBerry device. Email delivery to your old device has been stopped."
It then lists the three email accounts I had on my previous Blackberry, and I click on "Move". It prompts me to enter my passwords for each email address, I do, and it says "Your password has been successfully validated." It shows all three email addressess. I return to my home screen, and the email icons are not there. I go back to Email Account Management, and it prompts me to "move" my email accounts and enter passwords all over again. I've done this at least 20 times at this point.
HELP!

Hi and Welcome to the Community!!
I suggest the following steps, in order, even if they seem redundant to what you have already tried (steps 1 and 2 each should result in a message coming to your BB...please wait for that before proceeding to the next step):
1) Register HRT
KB00510 How to register a BlackBerry smartphone with the wireless network
2) Delete and Resend Service Books
KB05000Delete the service book for the BlackBerry Internet Service email account from the BlackBerry smartphone
KB02830 Send the service books for the BlackBerry Internet Service
3) Batt Pull Reboot
Anytime random strange behavior or sluggishness creeps in, the first thing to do is a battery pop reboot. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes. See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Hopefully that will get things going again for you! If not, then you should contact your wireless service provider for formal support.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

HP Laserjet 1020 problem with double-side printing

Hi, everyone!
I have a problem with my printer HP laserjet 1020. From the community I know that there is no driver for 1020, but there is for 1022 (http://support.apple.com/kb/DL907). I installed it and everything was fine until I tried to print 2-sided page... It appears 2-sided option disappeared and I don't know how to fix this...
Can anyone help, please?
Thank you for looking.

AMW122,
The part in the photograph appears to be part of the fuser assembly. If it is part of the fuser assembly, I would recommend you replace the fuser. An internet search on "LaserJet 3300 fuser" found several links.
From what I can see, it appears that the fuser sleeve is damaged which will continue to worsen.
If it is not the fuser, can you post another photograph further away so that we can see the location on the printer where it is located, etc...
Kaz
Kazman
I am an HP Employee
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

Problem with TMS setup in HA systems

Dear colleagues,
Our team have installed a new production environmnent to ECC in HA. We have a ASCS in cluster and two dialog instance in each server(local instance).
A virtual host GPPR3CIB and two instances in local, node GPPR301 and node GPPR302. This is an ECC 6.0 on Windows 2003 Server and SQL server 2005.
The architecture is as follows:
- GPPR301 node:
   - Virtual ASCS ASCS_0 (message server)
   - ABAP Primary Instance PPR301_1 (disp+work)
   - ERS (Enqueue replication server) instace ERS_10
- GPPR302 node:
   -ABAP Additional Instance PPR302_2 (disp+work)
   -Virtual Database Instance GPPR3DB
   -ERS (Enqueue replication server) Instance ERS_10
Once the installation is complete you need to apply SAP Note No. 943334 - "TMS setup in high availability systems" to set up high availability STMS. The problem is to distribute the configuration after running
the report " 'TMS_MGR_LOADBALANCING" described in SAP note.
The message indicates problems trying to run the command tp.exe. It has followed the note No. 1010990 and we have checked the folder permissions of the kernel but the problem persists.
Any information or help regarding this type of setup would be welcome.
Thanks.

Hi,
We have solved the problem with STMS. After several tests, the problem was in the parameter SAPLOCALHOSTFULL. This parameter must be assigned the hostname of the local system for each profile instance. If you've assigned the virtual host in the cluster generates the error in the distribution of the STMS.
Regards.

HP Laserjet CP1025nw problem with network setup

Similar Messages

Maybe you are looking for