HP LP2065- Need to connect 2 together for extended view

Hi,
I'd like to connect 2 HP LP2065 monitors together for extended viewing. ( Dragging files from one screen to another, not mirroring ). Can this be done without a Dual Monitor KVM switch? Thanks for any feedback or help in advance.
Note:
I currently run 1 HP LP2065 monitor with 2-3 laptops using a 4 port single monitor KVM switch. This set up works fine for one monitor. Online forums suggest getting a Dual Monitor KVM switch to run 2 monitors. But those switches cost $225 plus. And I can score another used HP LP2065 for less than $75

My first thought would be to add the Radeon 2600, it does work in 2007 models running Leopard. And the cost is acceptable.
As long as the X1900 is fine, no need to swap out for the newer 3870 just yet.

Similar Messages

  • Screen Structure for Extended View" in "Overview of Notification Type"

    Dear Members,
    When I am using the function "Screen Structure for Extended View" in "Overview of Notification Type" in SPRO, I am not able to make any changes to "Tab Page Allocation" and areas under "Screen Area"  What should i do to overcome this.
    Thanks & Regards

    Hi,
    The  "Tab Page Allocation" setting determines how many sub-screens can be added to the tab. It is therefore not possible to change this field for some tabs which are designed to be single screen only. Example - 10\TAB10 (items), 10\TAB11 (tasks).
    Should be changeable on tabs that allow multiple subscreens. Exampel - 10\TAB02 (Additional data).
    -Paul

  • IW21 Classification screen structurre for extended view for a notification type

    Hi Guru's,
    In Spro I added a screen structurre for extended view for a notification type
    I have well the subscreen now but the labels are missing and the button classification doesn't work.
    I guess that I should implement an user-exit or a badi.
    Any idea please ?
    Regards,
    Rahhaoui

    See this picture  This is from the same thread I referred earlier. I feel there should be better ways of learning these fundamentals about Module-pool programming, rahhaoui !
    Best of luck
    Jogeswara Rao K

  • Help needed in Joining tables for  Help view

    Hi All ,
    My requirement is create a search help , using a view which will join four table ,
    I was able to do using a databaser view and joining below tables
    KNA1     MANDT     =     KNVV     MANDT
    KNA1     KUNNR     =     KNVV     KUNNR
    TVV5     MANDT     =     KNVV     MANDT
    TVV5     KVGR5     =     KNVV     KVGR5
    TVV5     MANDT     =     TVV5T     MANDT
    TVV5     KVGR5     =     TVV5T     KVGR5
    But thes is doing a inner join and help is not providing valuse where tghere are no entries for KNVV-KVGR5
    for outer join i came to know we use hep view s instead of database viow ,
    But i have problem joining these table s while creating Help View .
    Any Help will be appricaited
    Thanks
    Vinay Kolla

    Hi Vinay,
    Use the tabls in below given order to get the right view.
    KNVV
    KNA1
    TVV5
    TVV5T
    KNA1-MANDT  = KNVV-MANDT
    KNA1-KUNNR = KNVV-KUNNR
    TVV5-MANDT = KNVV-MANDT
    TVV5-KVGR5 = KNVV-KNVV
    TVV5-MANDT = TVV5T-MANDT
    TVV5-KVGR5 = TVV5T-KVGR5
    Regard
    Anees

  • Need help with pushview for multiple view files

    Does anyone know how to create a pushview function or changeHandler function that would allow each item on a list when selected to change to a different view?
    Example is that if like has 1, 2, 3 on it selecting 1 would take user to view1.mxml, selecting 2 would send user to view2.mxml, etc.  I do not want to send all list items to the same view and just load different information.
    Thanks!

    I will check that out thanks! 
    In the mean time I did get the answer - see here: http://stackoverflow.com/questions/8936115/how-to-create-multiple-events-in-a-single-list- in-flex

  • How to create variant for table/view ?

    Hi,
    When I go through SM30, I find a radio button called variant. I don't know the effect.
    Can anyone tell me how to create variant for table / view ?
    I want to know when we need to create variant for table/view.
    Best regards,
    Chris Gu

    hi ,
    Whenever you start a program in which selection screens are defined, the system displays a set of input fields for database-specific and program-specific selections. To select a certain set of data, you enter an appropriate range of values.
    For further information about selection screens, refer to Selection Screens in the ABAP User's Guide.
    If you often run the same program with the same set of selections (for example, to create a monthly statistical report), you can save the values in a selection set called a variant
    Procedure
    To create a new variant:
           1.      On the ABAP Editor initial screen, enter the name of the program for which you want to create a variant, select Variants, and choose Change.
           2.      On the variant maintenance initial screen, enter the name of the variant to be created.
    Note the naming convention for variants (see below).
           3.      Choose Create.
    If the program has more than one selection screen, a dialog box for screen assignment appears. The dialog box does not appear if the program only has one selection screen. The selection screen appears in this case.
           4.      If there is more than one selection screen, select the screens for which you want to create the variant
    5.      Choose Continue.
    The (first) selection screen for the report appears.
    If your program has more than one selection screen, use the scroll buttons in the left-hand corner of the application toolbar to navigate between them and to fill the fields with values. If you keep scrolling forwards, the Continue button appears on the last selection screen.
           6.      Enter the desired selection values, including multiple selection and dynamic selection.
           7.      Choose Continue.

  • What do put in templates for website viewing on phone & tablets

    I followed directions for website viewing on Phone, Tablet, Desktop, but is is still not working, to leave it blank it will default to desktop viewing, but I don't understand what do I put in the templates for Phone viewing and Tablet viewing I included the {tag_pagecontent} in all 3 templates.
    Do I checkmark DEFAULT TEMPLATE this is where to upload on the Admin side, after I upload the files with the htm extension, finally I clicked SAVE & PUBLISH.
    What do I need to in templates for Phone viewing and Tablet viewing.
    Attached is the info I have in the templates I created in DreamWeaver with a htm extension, the SAME info is in all 3 templates:
    <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
    <html xmlns="http://www.w3.org/1999/xhtml">
    <head>
    <meta http-equiv="Content-Type" content="text/html; charset=utf-8" />
    <!-- TemplateBeginEditable name="doctitle" -->
    <title>Untitled Document</title>
    <!-- TemplateEndEditable -->
    <!-- TemplateBeginEditable name="head" -->
    <!-- TemplateEndEditable -->
    </head>
    <body>
    <!-- TemplateBeginEditable name="ContentArea" -->{tag_pagecontent}<!-- TemplateEndEditable -->
    </body>
    </html>
    HELP HELP HELP
    Judy

    You must be checking it in Email Me function. Once you send a real campaign the link will work on every platform under the sun.
    Cheers,
    -mario

  • Extending View Object at Responsibility level.

    Hi All,
    Is it possible to extend view object at responsibility level?
    Please tell me steps for extending view object at responsibility level/function level.
    Thanks in advance.
    Laukik Pachanekar

    Substitution of VO & AM will can be done only at site level. However controller extension can be personalized/substituted at any level, which includes responsibility level also.
    Thanks,
    --Anil
    http://oracleanil.blogspot.com/

  • Instructions for extending a wireless network through a wired connection

    These are the instructions for extending a wireless network by wiring two airports together.
    The benefit of this is to provide a strong signal in more locations in your home or business.
    The advantage of this technique over WDS is that the wired connection is faster and more reliable.
    These instructions assume you have a) an existing wireless network setup using an airport , b) a new airport that you want to add to your network, c) you can run a cat 5 cable between the two airports, and d) you are familiar with the airport utility.
    If while using these instructions you are prompted to update your airport firmware please do so.
    1) Gather the following information from your existing Airport on the Summary tab of Airport utility:
    a) Wireless Network Name
    b) Wireless Security
    c) You will also need the password, which hopefully you just know.
    2) Plug in your new Airport, connect it to the existing Airport using a cat 5 cable.
    3) Reset the new Airport using the tip of a paper clip. On my Airport Express that is next to the audio out.
    4) After a short wait the new Airport should appear in Airport Utility with a generic name.
    5) Click the new airport and click "Manual Setup". You may have to cancel out of some popups to get to the Manual Setup button.
    6) On the "Base Station" tab set a "Name" that does NOT equal the the name of your old Aiport. Also set the password. This us the password that one uses to make changes to the setup of the Airport.
    7) On the "Wireless" table set a "Wireless Network Name", "Wireless Security", and "Password" to exactly match that of your old Airport. This is the password that one uses to gain access to the network.
    8) On the "Internet->Internet Connection" tab set connection sharing to "Off (Bridge Mode)".
    9) Click "Update" at bottom right of Airport Utility.
    10) Test by using "Advanced->Logging and Stats->Wireless Clients" to see which clients are connecting to which Airport.

    viafax999 wrote:
    coolhwhip wrote:
    Thanks for the reply.  Like I said, I am pretty new to this.  So I need to buy something like this to put in my media center then?
    http://www.amazon.com/Hawking-HWREN1-Hi-Gain-Wireless-300N-Extender/dp/B001DMEYCY/ref=sr_1_1?s=pc&ie...
    Do I even need the Wireless N router at all, or will the Westell do the trick?  I'd be looking to stream HD from my main home PC, so I need good wireless speed.
    I assume that there is a tv in your media center so what would make much more sense would be to get a coax splitter and split the coax at that tv and then move the vz westell router to the other side of the splitter.  It really makes no matter where the westell router is on the coax setup and doing this should allow you to connect your devices directly to the router.
    So the coax feed from the ONT comes in through the garage into the office and is connected to the Westell in the office (which is hard-wired into my office PC).   If I move the Westell to the entertainment center I'll be in the same boat w/ my office PC then, i.e. needing a wireless connection to the Westell to get internet access.  Am I missing something here?

  • I need to connect my Imac 27'' (newest version) up to 3/4 monitors (all 40'' LCD tv's with VGA and HDMI connections) with extended display to all external screens, not duplicate images. Is this possible?

    i need to connect my Imac 27'' (newest version) up to 3/4 monitors (all 40'' LCD tv's with VGA and HDMI connections) with extended display to all external screens, not duplicate images. Is this possible?

    I would suggest you visit an Apple dealer, preferably an Apple Store if there's one in your city, and ask for assistance in determining what you need. The questions and issues you bring up are rather complex to address in a technical support forum and would be better addressed in person where you and the salesperson can ask questions back and forth to arrive at the optimal setup.
    Regards.

  • Which cable do I need to connect my Mac Book Pro to my Panasonic PV-GS150 video camera for transferring video to iMovie?

    which cable do I need to connect my Mac Book Pro to my Panasonic PV-GS150 video camera for transferring video to iMovie?

    I totally understand.
    Check some things from here, I have 2 and they have been great so far.
    Check here, lots of storage and reasonable prices. Also great support, you get to speak to a person
    Clean off your on the G5 drive and off you go.
    I suggest buying a second drive and setting it up for a back up, Time Machine or Carbon Copy Cloner, or SuperDuper (both "bootable" back up) All searchable on the web.
    http://eshop.macsales.com/search/elite+pro
    You can talk to a person for REAL advice, Phone: 800.275.4576  Ask about exporting to your G5 and and exporting to your existing OSX, you may only need a small inexpensive drive for this.
    Quick delivery and willing to help.
    Hope this makes you back up and running :-)
    Do get a back up drive, as it is not ""whether my drive will fail, as much as "when my drive fails"
    All the best

  • What cables do I need to connect my 2013 macbook pro to my HD tv? I know I need mini display to HDMI, but male? female HDMI??? and also, do I need a separate cable for sound?

    what cables do I need to connect my 2013 macbook pro to my HD tv? I know I need mini display to HDMI, but male? female HDMI??? and also, do I need a separate cable for sound?

    Actually you need a Thunderbolt to HDMI adapter. It will carry both audio and video.
    This one will work: Mini DisplayPort | Thunderbolt® to HDMI® Adapter w/ Audio Support

  • I have the G Drive 1 TB (GEN4 1TB) external drive purchased in 2010. I need to connect to my new MacBook Pro. I'm using the external drive for media storage of my video editing projects. Will a 800fw to thunderbolt adapter cable work?

    I have the G Drive 1 TB (GEN4 1TB) external drive purchased in 2010. I need to connect to my new MacBook Pro. I'm using the external drive for media storage of my video editing projects. Will a 800fw to thunderbolt adapter cable work? I understand that using a USB port connection is not fast enough for video editing. I read somewhere the G Drives don't connect well to MacBook Pro.
    thanks
    larry

    I doubt this can be relocated or moved so you might want to just repost in the macbook pro area.
      MacBook Pro
    https://discussions.apple.com/community/notebooks/macbook_pro
    https://discussions.apple.com/community/mac_os?view=discussions
    Can you afford a new Thunderbolt case and cable? any case with FW800 is going to be slow 72MB/sec and less, and any new 1TB drive is capable of 75MB/s minimum up to 125MB/sec.
    Thunderbolt storage can of course when setup properly reach 100's of MB higher using multiple drives.
    Use what you have for a system backup or for secondary backup storage.
    you might be able to take the drive - most cases allow you to open and swap drives - and use this:
    G-Technology 1TB G-DRIVE mini High-Speed Portable Hard Drive                                   
    or this:
    http://store.apple.com/us/product/HB137VC/A/g-technology-4tb-g-raid-professional -high-performance-dual-drive-hard-drive?fnode=5f

  • I have a hard drive for CD storage that needs to connect to the Ethernet router. sInce my router is not in this room, and in another room, I want to use my Mac as a router for the drive, and share the wifi. Ho do I do this

    I have a hard drive for CD storage that needs to connect to the Ethernet router. sInce my router is not in this room, and in another room, I want to use my Mac as a router for the drive, and share the wifi. Ho do I do this? I gace tried the System Preferences -> Sharing, shared internet to Ethernet, but can't se ethe device on Finder

    Djembe wrote:
    UEFI (unified extensible firmware interface) boot requires Global unique identifier Partition Table (GPT) as opposed to the older Master Boot Record (MBR). If your existing drive is formatted in MBR, you will need to adjust BIOS settings to enable legacy boot in order for it to work properly.
    Is there a performance difference between GPT and MBR? If GPT is better, I do not mind formatting the drive with it.
    5. No special drivers are needed.
    Thanks. What about the thunderbolt port?
    7. I think Lenovo estimates 6 hours.
    Lenovo says 6 hours with the 6-cell battery on its website.
    BrendaEM wrote:
    Hi,
    There was a serious BIOS/UEFI problem with that SSD . Perhaps this thread will save you some headaches. Someone is recomending shutting off Rapid Boot in the setup, which would probable mean little with a SSD, anyway.
    I read through this, and it looks like the problem was fixed in a BIOS update, which I plan to do. However, it also seems like Intel Rapid Start is not even worth it in the first place, as sleep consumes almost no power at all.
    W540: i7-4700mq, K2100m, 8 GB DDR3L, 512 GB SSD
    T510: i7-620m, NVS 3100m, 8 GB DDR3, 512 GB SSD

  • HT3014 my mac has the VGA port and I need a newer monitor for it. what do I use that will connect it. I had a new dell monitor and none of the things that dell said worked. so I am going to get a mac monitor for a second unit.

    my mac has the VGA port and I need a newer monitor for it. what do I use that will connect it. I had a new dell monitor and none of the things that dell said worked. so I am going to get a mac monitor for a second unit.
    my laptop is a 2008 model

    Hmmm... 2008 MBP has...
    Video (Monitor):     1 (DVI)
    Details:     Supports external display in dual display and mirroring modes. VGA output provided by included Apple DVI-to-VGA adapter, S-video output provided by optional adapter (sold separately).
    http://www.everymac.com/systems/apple/macbook_pro/specs/macbook-pro-core-2-duo-2 .5-15-early-2008-penryn-specs.html

Maybe you are looking for